All in All 360 Rotate i-Size - Car seat COSATTO - Free user manual and instructions

Product type	Car seat
Brand	Cosatto
Model	All in All 360 Rotate i-Size
Compliance	Regulation No. 129 (Enhanced i-Size)
Usage modes	Rear-facing (40-105 cm, up to 19.5 kg), Forward-facing (76-150 cm, up to 19.5 kg), Booster (100-150 cm)
Rotation	360° with adjustment lever
Installation	ISOFIX (retractable arms) + telescopic support leg
Maximum child weight	19.5 kg
Reducer	Used according to height (with or without side and headrest cushions)
Harness	5-point, adjustable, safety buckle
Headrest	Height adjustable
Backrest recline	Rear-facing: position R; Forward-facing: positions 1-4; Booster: position 1
Side shield	Integrated
Safety indicators	Green on ISOFIX arms and support leg
Cover maintenance	Machine washable (follow labels), no abrasive detergent
Parts cleaning	Sponge with warm water and mild detergent
Spare parts available	Reducer, cushions, covers, ISOFIX guides, etc. (see manual)
Warranty and support	Contact Cosatto ([e-mail]) or website
Storage of manual	Pocket at the back of the seat
Minimum age forward-facing	15 months
Do not use	On seat with active airbag

Frequently Asked Questions - All in All 360 Rotate i-Size COSATTO

How to install the seat in rear-facing mode?

Place the seat in rear-facing orientation, backrest in position R. Attach the ISOFIX arms to the anchor points (green indicators) and deploy the support leg until it touches the floor (green indicator).

Can I rotate the seat 360° while driving?

No, rotation is only allowed when stationary to facilitate installation and access to the child. Never drive in the lateral position.

When to use the reducer and its cushions?

For a child of height ≤ 60 cm: use the full reducer (side and headrest cushions). From 61 to 87 cm: reducer alone without cushions. From 88 cm: remove the reducer.

How to clean the seat cover?

Remove the cover following instructions (detach elastics and fasteners). Machine wash according to label, without abrasive detergent (bleach, ammonia). Dry completely before putting it back.

What to do after a car accident?

The car seat and belts must be replaced even if they seem intact. An accident may reduce their protective capacity. Contact Cosatto for a replacement.

Can the seat be used as a booster without ISOFIX?

Yes, in booster mode (100-150 cm), you can use only the vehicle seat belt. In this case, retract the ISOFIX arms and support leg, and secure the child with the seat belt (guide in the headrest).

How to know if the ISOFIX installation is correct?

The safety indicators on the ISOFIX arms and support leg must be fully green. If any indicator is red, the installation is not secure.

Can this seat be used on the front passenger seat?

Yes, provided the airbag is deactivated. Consult the vehicle manual to deactivate the airbag. Never use with an active airbag.

What regular maintenance is recommended?

Regularly inspect the seat (harness, buckle, ISOFIX, cover). Clean plastic/metal parts with a damp cloth. Store away from humidity and sunlight.

Where to find spare parts?

Spare parts (reducer, cushions, covers) are available on the Cosatto website (for UK/Ireland) or via distributors listed at www.cosatto.com/stockists. Contact [e-mail] for assistance.

USER MANUAL All in All 360 Rotate i-Size COSATTO

All in All Rotate i-Size i-Size Car Seat

R129/03 40 - 105cm ≤19.5kg 100 - 150cm

(EN) Instruction 1-32

(FR) Instruction, (DE) Gebrauchsanleitung, (IT) Istruzioni

(EN) Part list diagram

33

(FR) Schéma de nomenclature, (DE) Teilelisteabbildung,
(IT) Diagramma della lista delle parti

(EN) Spare part list diagram 34

(EN) Instruction diagram 35-48

(FR) Schéma d'instructions, (DE) Anleitungsdiagramm,
(IT) Diagramma di istruzioni

Important: Keep these instructions for future reference.

Important safety Information

The instruction manual should be kept safely with child car seat for its life period:

There is a compartment at the rear of the child car seat for storage of the instruction manual.

It is recommended to check that the child restraint is compatible with the intended vehicle at the time of purchase.

Please refer to the vehicle list, Cosatto fit checker app (http://cosat.to/fitchecker) or the vehicle fitting list section on the website (http://cosat.to/allinallrotateisizevl).

Seat positions in other vehicles may also be suitable to accept the child restraint. If in doubt, consult either Cosatto or the retailer.

Child age and weight:

• When used in rearward facing mode, the car seat is suitable from birth, height between 40 and 105cm , up to maximum weight of 19.5kg .
• IMPORTANT - DO NOT USE FORWARD FACING BEFORE THE CHILD'S AGE EXCEEDS 15 MONTHS.
• When used in forward facing mode, the car seat is suitable from 15 months, height between 76 and 105cm , up to maximum weight of 19.5kg .
• When used in booster mode, the car seat is suitable for height between 100 and 150 cm .

Location:

• Refer to the vehicle list for information of where the child car seat base will fit in your vehicle.
• Never use the child car seat on a seat where an airbag is fitted and active. Refer to your vehicle user manual for information on de-activating the airbag.
• If the vehicle seat backrest has a recline function, place the vehicle seat in the most upright position when using the child car seat.
• Do not use the child car seat in the home. It has not been designed for home use and should only be used in your car.

Safety - Please read carefully:

• NEVER use this child car seat with its side facing the vehicle seat.
• Any rigid items and plastic parts of the child car seat must be so located and installed that they are not liable, during everyday use of the vehicle, to become trapped by a movable seat or in a door of vehicle.
• If any load bearing points other than those described in the instructions are used, this can significantly reduce the protection factor of the child car seat.
  ALWAYS secure your child with the safety harness when using this child car seat.
• Never leave your child unattended.
• Do not attempt to dismantle, modify or add to any part of the child car seat or change the way your vehicle seat belts are made or used.
• After an accident the child car seat should be replaced and the vehicle seat belts. Although they may look undamaged, they may not protect your child as well as they should.
• Do not place anything such as a towel or cushion under the child car seat. This could affect the performance of the child restraint system in an accident.
• Any vehicle seat belt holding the child car seat to the vehicle should be tight, and that belt should not be twisted.
• Always make sure that the child car seat harness and vehicle seat belt are correctly tensioned to ensure maximum protection for your child.
• Prevent harness/ vehicle seat belt from getting trapped between car doors or rubbing against sharp parts of the seat or body.
• If the harness/vehicle belts becomes cut or frayed, replace it before travelling.
• Never use replacement parts other than those approved by Cosatto.
• Cosatto advise that child car seat should not be bought or sold second-hand. Many child car seat acquired this way have been found to be dangerous.
• NOTE: The child car seat can mark vehicle seat upholstery. Cosatto cannot be held responsible for damage or marking to vehicle seat upholstery.
• Security is only guaranteed if the child car seat is fitted in accordance with these instructions.
• Safely secure any luggage or other objects that might cause injuries to the occupant of the child car seat in the event of a collision.
• Failure to comply with the instructions would be dangerous, and will automatically void the warranty and exempt Cosatto from any liability.
• The harness buckle has been designed to be released quickly in an emergency. IT IS NOT CHILD PROOF. More inquisitive children may learn to undo the buckle. Children should be told never to play with the harness buckle or any other part of the child car seat.
• It is important that the lap harness is worn low down, so that the pelvis of the child is firmly engaged.
• In booster seat mode, the lap vehicle seat belt must be worn in such a way as to properly secure the pelvis of the child.
• Never use the child car seat without its fabric cover because the fabric cover constitutes as an integral part of the child car seat performance. The fabric cover should not be replaced with any other than the ones recommended by Cosatto.
• Cover the child car seat if it is left in direct sun light for prolonged period as the child car seat base surfaces may get very hot. Check the child car seat surface before placing your child in the seat.

Notice:

1. (40 - 105cm) This is an i-Size Enhanced Child Restraint System. It is approved according to Regulation No.129, for use in, i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle users' manual.
2. (100 - 150cm) This is an i-Size booster seat Enhanced Child Restraint System. It is approved according to UN Regulation No.129, for use primarily in" i-Size seating positions" as indicated by vehicle manufacturers in the vehicle user's manual.
3. Never use this child car seat on passenger seat fitted with an active airbag is installed.
4. If in doubt, consult either the child restraint manufacturer or retailer.

Care & Maintenance:

• Your child restraint system has been designed to meet safety standards and with correct use and maintenance will give many years of trouble free performance.
• Store your child restraint system in a dry, safe place.
• Storing a damp child restraint system will encourage mildew to form, so after exposure to damp conditions, dry off with a soft cloth and allow to dry thoroughly before storing.
• Avoid leaving the child restraint system in sunlight for prolonged periods as this may cause fabrics to fade.
• Inspect the child restraint system regularly for signs of damage- stop using the product if damage is found.
• DO NOT take apart, or attempt to take apart the child restraint system when cleaning. It is unnecessary and dangerous to do so.
• Plastic and metal parts may be sponged clean with warm water and a mild detergent.
  Refer to the wash care on soft goods for cleaning instruction.
• Remove insert from seat cover/ seat liner prior to cleaning.
• Never clean with abrasive, ammonia based, bleach based or spirit type cleaners.

Visual language Key:

XX	Refer to warning XX
√	Correct action
X	Incorrect action
{click}	Audible sound

Repeat action x times

General action arrow

Lock

Unlock

	Press and hold
	Check
Cont. XX	Continue to step XX
	Repeat on other side

Part List:

Please refer to diagrams:
P1: Headrest P8: ISOFIX arm
P2: Seat liner head section P9: Side impact protection block
P3: Seat liner P10: Storage compartment
P4: Seat liner side wing section P11: Support-leg
P5: Chest pads (pair) P12: ISOFIX guide (x2)
P6: Harness P13: Tuck in tool
P7: Crotch pad

Replacement Parts:

The replacement parts shown below are available for your product. For UK & Ireland customers, order through our website: http://www.cosatto.com/service-centre/spar
For customer outside UK & Ireland, contact information for your local distributor can be found on http://www.cosatto.com/stockists
If you require any further assistance, please contact us at [e-mail]
S1: Seat liner S7: Crotch pad
S2: Seat liner wedge S8: Chest pads (pair)
S3: Seat liner head section S9: Headrest cover
S4: Seat liner side wing section (right) S10: Seat cover
S5: Seat liner side wing section (left) S11: ISOFIX guide (set)
S6: Seat liner side wing section insert S12: Tuck in tool

Fitting & Operation Information:

Please refer to the following diagrams:

Location 1- IMPORTANT: Never use the child car seat on a seat where an airbag is fitted and active. Refer to your vehicle user manual for information on de-activating the airbag.

Backrest 2- Adjusting:

recline Important: Only use the specified recline position(s) for each mode:

Rearward facing mode (40 - 105cm): R

Forward facing mode (76 -105cm): 1, 2, 3, 4

Booster seat mode (100 - 150cm): 1

Headrest 3-Adjusting:

4-Satisfactory headrest position:

Harness 5-Crotch strap adjustment:

6- Loosening:

NOTE: Pull only the harness straps.

7-Tightening:

NOTE: The harness must be reasonably tight. It should restrain but not make the child uncomfortable.

Check that the straps are not twisted while the child is seated.

8- Opening:
9-Closing:

Securing your child in the child car seat:

10- Open the harness (refer to step 8) (a). Raise the headrest (refer to step 3) (b).
11- Place your child in the child car seat. Close the harness (refer to step 9) (a). Adjust the headrest (refer to step 6) (b). Tighten the harness (refer to step 7) (c).

Side impact protection block

12- Opening:
13-Closing:

Child car seat

14- Adjusting the seat unit's orientation:

Open the support-leg fully (a).

Pull and hold the seat rotate adjustment lever (b) then rotate the seat (c).

15- Seat positions:

b, c: Sideward facing position:

The sideward facing position allow access for placing or removing a child from the seat unit after the car seat is fitted.

WARNING: Do Not travel with the seat unit in this position.

d: Rearward facing position:

When use as a rearward facing child car seat, the car seat is suitable from birth, height between 40 and 105cm , up to maximum weight of 19.5kg .

IMPORTANT - DO NOT USE FORWARD FACING BEFORE THE CHILD'S AGE EXCEEDS 15 MONTHS.

a: Forward facing position :

When use as a forward facing child car seat, the car seat is suitable from 15 months, height between 76 and 150~cm

Note: In booster seat mode, the seat unit cannot be rotated.

ISOFIX arm 16- Location:

The two ISOFIX low anchorage anchor points are usually located between the vehicle seat base and back (a).

Some vehicles have ISOFIX indicator near the ISOFIX low anchorage anchor points (b).

17-Fitting the ISOFIX guides (Optional):

The ISOFIX guides can help identify the vehicle ISOFIX anchor points and make installation easier. They can also help with the protection of your vehicle seat.

18-Fitting:

Press and hold ISOFIX arm adjustment buttons and extended the arms fully (a).

Engage the ISOFIX arms (b) and ensure that the ISOFIX arm security indicators are green (c).

Push the base back until it rests firmly against the vehicle seat backrest (d).

Removal is a reversal of this procedure.

Support-leg 19-Fitting:

Open the support-leg fully (a).

Adjust the support-leg (b) until it makes firm contact with vehicle floor (c) and the support-leg contact indicator is green (d).

Rearward facing mode (40 - 105cm):

20-Fitting:

Convert the seat unit to rearward facing orientation (refer to step 14).

Recline the backrest to position R (refer to step 2) (a).

Position the child car seat on the vehicle seat, rearward facing.

Attach the ISOFIX arms to the anchor points (refer to step 16 - 18) (b).

Engage the support-leg (Refer to step 19) (c).

Removal is a reversal of this procedure.

Seatliners 21-

When your child's height is 60~cm or below, the child car seat must be used WITH the seat liner, head & side wing sections.

When your child's height is between 61 and 87~cm the child car seat must be used with the seat liner section only, WITHOUT the head & side wing sections.

When your child's height 88 cm or above, the child car seat must be used WITHOUT the seat liner, head & side wing sections.

Forward facing mode (76 - 105cm):

IMPORTANT - DO NOT USE FORWARD FACING BEFORE THE CHILD'S AGE EXCEEDS 15 MONTHS.

22-Fitting:

Convert the seat unit to forward facing orientation (refer to step 14).

Recline the backrest to position 1,2,3 or 4 (refer to step 2) (a).

Position the child car seat on the vehicle seat, forward facing.

Attach the ISOFIX arms to the anchor points (refer to step 16 - 18) (b).

Engage the support-leg (Refer to step 19) (c).

Removal is a reversal of this procedure.

Booster seat mode (100- 105cm):

Converting to booster seat mode:

23- Unfasten the rear zip (a) and open the rear compartment door (b). Disconnect the chest pads connector rod (c & d) and store in the storage slot (e).

Close the rear compartment door & fasten the rear zip (f).

24- If fitted, remove the seat liner.

Loosening the harness (refer to step 6) (a).

Raise the headrest to its highest position (refer to step 3) (b).

Open the harness (refer to step 8) and remove the chest pads (c) & crotch pad (d).

25- Press the buckle behind the seat cover (a) and unfasten the seat cover flap (b).

Close the harness (refer to step 9) and store it in the storage compartment (c).

The buckle must be stored lowdown in the storage compartment.

Belted only:

Fitting:

26- Decline the backrest to position 1 (Refer to step 2) (a).

Position the child car seat on the vehicle seat, forward facing.

Retract the ISOFIX arms (refer to step 18) (b).

Retract the support-leg (Refer to step 19) (c).

Secure your child with vehicle belt (refer to step 27 - 28) (d).

Removal is a reversal of this procedure.

Vehicle belt 27- Place your child into the child car seat.

Pull the vehicle belt out and around the child (a) and fasten the buckle (b).

Fit the diagonal vehicle belt through the headrest diagonal vehicle belt guide (c).

28-Tension the vehicle belt (a & b).

IMPORTANT: The position of the vehicle belt buckle can affect the stability of the child restraint system. In an accident this could stop the child restraint system from protecting your child as well as it should. After tightening the vehicle belt, if the buckle lies in the position marked (X) then try fitting the child restraint system in another seating position in your vehicle.

Removal is a reversal of this procedure.

Belted with ISOFIX arms only:

29-Fitting:

• Recline the backrest to position 1 (Refer to step 1) (a).
• Position the child car seat on the vehicle seat, forward facing.
• Attach the ISOFIX arms to the anchor points (refer to step 16 - 18) (b).
• Retract the support-leg (Refer to step 19) (c).
• Secure your child with vehicle belt (refer to step 27 - 28) (d).
• Removal is a reversal of this procedure.

Softgoods Removing:

30- Convert the car seat to booster seat mode (refer to step 23 - 25). Unfasten the headrest cover elastic loops on both sides (a). Remove the headrest cover (b).

31- Unfasten the seat cover front plastic retainers (a). Unfasten the seat cover flap (b) and the seat cover elastic loops (c). Release the fabric around side impact protection blocks (d). Remove the seat cover (e). Reverse the procedures above to refit the softgoods.

Tuck in tool 32- Using the tuck in tool:

Checklist:

• Have you check the compatibility of the child car seat with the intended vehicle?
• If applicable, is the air-bag de-activated?
• Is your child car seat correctly fitted to the vehicle seat?
• Have you check the safety indicators on ISOFIX arms, ISOFIX support-leg?
• Is your child correctly secure in the child car seat?
• Is harness adequately tensioned and not twisted?

http://www.cosatto.com/service-centre/spares

*calls from BT landlines are free but calls from mobiles and other networks may vary.

Email: [e-mail]

Letter: Cosatto Limited, Bentinck Mill, Bentinck Street, Farnworth,

Bolton, Lancs, BL4 7EP, England.

All the design and trademarks contained herein are the property of Cosatto Limited.

No part of this document may be reproduced without the permission of Cosatto Limited.

www.cosatto.com

(EN) Notice:

(40 - 105cm) This is an i-Size Enhanced Child Restraint System. It is approved according to Regulation No.129, for use in, i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in the vehicle users' manual.

(100 - 150cm) This is an i-Size booster seat Enhanced Child Restraint System. It is approved according to UN Regulation No.129, for use primarily in "i-Size seating positions" as indicated by vehicle manufacturers in the vehicle user's manual.

For compatibility of non i-Size vehicle, please refer to the fit checker app (http://cosat.to/fitchecker) or the compatibility list on the website (http://cosat.to/allinallrotateisizevl).

Never use this child restraint system in seating positions where an active frontal airbag is installed.

Important - Do not use forward facing before the child's age exceeds 15 months (refer to instructions).

If in doubt, consult either the child restraint manufacturer or retailer.