P24ST - Grass trimmer Powerworks - Free user manual and instructions

USER MANUAL P24ST Powerworks

Exterior view of a gray electric tool with lever and base (no text or symbols visible)

STG305

CE

Original Instructions / Übersetzung der Originalanweisungen/ Traducción de las instrucciones originales/ Traduzione delle istruzioni originali/ Traduction des instructions d'origine/ Vertaling van de originele gebruiksaanwijzing/ Alkuperäisten ohjeiden käännös/ Översättning av original instruktionerna/ Produsentens instruksjoner/ Oversættelse af de originale vejledninger / Překlad originálního návodu/ Preklad originálneho návodu/ Prevod originalnih navodil/ Prijevod izvornih uputa/ Az eredeti utasítás fordítása/ Превод на оригиналните инструкции/ Orijinal Talimatların Tercümesi/ Originaalkasutusjuhendi tõlge

English

EN

1 Safety.... 2
2 Description.... 2

2.1 Purpose....2
2.2 Overview.... 2

3 Safety.... 2

4 Installation.... 2

4.1 Unpack the machine....2
4.2 Attach the guard....2
4.3 Assemble the shaft.....2
4.4 Install the battery pack.... 3
4.5 Remove the battery pack.... 3

5 Operation....3

5.1 Controls....3
5.2 Start the machine.... 3
5.3 Stop the machine.... 3
5.4 Operation tips....3
5.5 Cutting tips.... 3

5.6 Adjust the length of the cutting line.... 3
5.7 Adjust the length of the cutting line manually....3
5.8 Line cut-off blade....4
5.9 Change to the edging mode......4

6 Maintenance....4

6.1 General information....4
6.2 Clean the machine.... 4
6.3 Replace the spool....4
6.4 Replace the cutting line....4

7 Transportation and storage...... 5

7.1 Move the machine....5
7.2 Store the machine.... 5

8 Troubleshooting......5
9 Technical data.... 6
10 Warranty....6
11 EC Declaration of conformity......6

1 SAFETY

WARNING

Make sure that you do/obey all safety instructions.

Refer to Safety Manual.

2 DESCRIPTION

2.1 PURPOSE

This machine is used to cut grass, light weeds, and other similar vegetation at or around ground level. The cutting plane must be approximately parallel to the ground surface. You cannot use the machine to cut or chop hedges, shrubs, bushes, flowers and compost.

2.2 OVERVIEW

Figure 1 - 16.

1	Lock-out button
2	Trigger
3	Front handle
4	Upper shaft
5	Lower shaft
6	Cut-off blade
7	Trimmer head
8	Guard
9	Rotating handle latches
10	Positioning holes
11	Spool retainer button
12	Spool cover
13	Tab
14	Spool
15	Hole
16	Spool housing
17	Anchor hole
18	Guide slot
19	Battery release button
A	Direction of roatation
B	Best cutting area
C	Dangerous cutting area

3 SAFETY

WARNING

Make sure that you do/obey all safety instructions.

Refer to Safety Manual.

4 INSTALLATION

WARNING

Remove the battery pack from the machine before installation.

WARNING

Do not use accessories that are not recommended for this machine.

4.1 UNPACK THE MACHINE

WARNING

Make sure that you correctly assemble the machine before use.

WARNING

• If the parts have damage, do not use the machine.
• If you do not have all the parts, do not operate the machine.

• If the parts are damaged or missing, speak to the service center.

• Open the package.

• Read the documentation in the box.
• Remove all the unassembled parts from the box.
• Remove the machine from the box.
• Discard the box and package in compliance with local regulations.

4.2 ATTACH THE GUARD

Figure 2 - 3.

WARNING

Do not touch the cut-off blade.

1. Remove the screw from the trimmer head with a Phillips head screwdriver (not included).
2. Put the guard onto the trimmer head.
3. Align the screw hole on the guard with the screw hole on the trimmer head.
4. Tighten the screw.

4.3 ASSEMBLE THE SHAFT

Figure 4.

1. Push in the rotating handle latches on the lower shaft.
2. Align the latches with the positioning holes and slide the two shafts.

3. Turn the lower shaft until the latches locks into the positioning holes.

4. Insert the screws into the shaft.

5. Tighten the screws.

4.4 INSTALL THE BATTERY PACK

Figure 5.

WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the motor stops before you install or remove the battery pack.

• Read, know, and do the instructions in the battery and charger manual.

• Align the lift ribs on the battery pack with the grooves in the battery compartment.

• Push the battery pack into the battery compartment until the battery pack locks into place.
• When you hear a click, the battery pack is installed.
• Align the lift ribs on the battery pack with the grooves in the battery compartment.
• Push the battery pack into the battery compartment until the battery pack locks into place.
• When you hear a click, the battery pack is installed.

4.5 REMOVE THE BATTERY PACK

Figure 5.

1. Push and hold the battery release button.
2. Remove the battery pack from the machine.

5 OPERATION

i IMPORTANT

Before you operate the machine, read and understand the safety regulations and the operation instructions.

WARNING

Be careful when you operate the machine.

5.1 CONTROLS

5.2 START THE MACHINE

Figure 6.

1. Push the lock-out button and pull the trigger.

5.3 STOP THE MACHINE

Figure 6.

1. Release the trigger to stop the machine.

5.4 OPERATION TIPS

Figure 7.

WARNING

Keep clearance between the body and the machine.

WARNING

Do not operate the machine without guard in place.

Do these tips when you use the machine

• Keep the machine connected to the correctly worn harness.
• Keep a firm hold with the two hands on the machine while you operate the machine.
• Cut tall grass from the top down.

If grass winds around the trimmer head:

• Remove the battery pack.
• Remove the grass.

5.5 CUTTING TIPS

Figure 8.

• Tilt the machine toward the area to be cut. Use the tip of the cutting line to cut grass.
• Move the machine from right to left to prevent thrown debris toward the operator.
• Do not cut in the dangerous area.
• Do not force the trimmer head into uncut grass.
• Wire and picket fences cause cutting line wear and breakage. Stone and brick walls, curbs, and wood can wear the cutting line quickly.

5.6 ADJUST THE LENGTH OF THE CUTTING LINE

Figure 6.

NOTE

The machine has an auto-feed head. It will damage the machine if you hit the head to try to advance the line.

NOTE

If the cutting line does not automatically advance, it can be tangled or empty.

1. When the machine is on, release the trigger.
2. Wait two seconds, push the trigger again.

NOTE

The line will extend approximately 0.4 in. with each stop and start of the switch trigger until the line reaches the cut-off blade and the cut-off blade cuts the excess length.

5.7 ADJUST THE LENGTH OF THE CUTTING LINE MANUALLY

Figure 9.

1. Stop the machine.

2. Push the spool retainer button and pull on cutting line to manually advance the cutting line.

3. After you extend new cutter line, always return the machine to its normal position before you start it again.

5.8 LINE CUT-OFF BLADE

Figure 9.

This trimmer is equipped with a line cut-off blade on the guard. The line cut off blade continuously trims the line to ensure a consistent and efficient cut diameter. Advance line whenever you hear the engine running faster than normal, or when trimming efficiency diminishes. This will maintain best performance and keep line long enough to advance properly.

5.9 CHANGE TO THE EDGING MODE

Figure 10 - 11.

NOTE

You can change the machine to a well groomed edger for edging patios, driveways and walkways or other areas.

1. Stop the machine.
2. Push on the rotating handle latches and turn the trimmer head 180 degrees until the trimmer head locks into position.
3. Release rotating handle latches.
4. Insert the screws into the shaft.
5. Tighten the screws.

6 MAINTENANCE

i IMPORTANT

Read and understand the safety regulations and the maintenance instructions before you clean, repair or do the maintenance work on the machine.

i IMPORTANT

Make sure that all nuts, bolts and screws are tight. Examine regularly that you install the handles tightly.

i IMPORTANT

Use only the replacement parts and accessories of the initial manufacturer.

6.1 GENERAL INFORMATION

i IMPORTANT

Only your dealer or approved service center can do the maintenance that is not given in this manual.

Before the maintenance operations:

• Stop the machine.
• Remove the battery pack.
• Cool the motor.
• Store the machine in cool and dry place.
• Use correct clothing, protective gloves and safety glasses.

6.2 CLEAN THE MACHINE

• Clean the machine after use with a moist cloth dipped in neutral detergent.
• Do not use aggressive detergents or solvents to clean the plastic parts or handles.
• Keep the trimmer head free of grass, leaves, or excessive grease.
• Keep the air vents clean and free of debris to avoid overheating and damage to the motor or the battery.
• Do not spray water onto the motor and electrical components.

6.3 REPLACE THE SPOOL

Figure 12.

1. Push the tabs on the sides of the trimmer head at the same time.
2. Pull and remove the spool cover.
3. Remove the spool.
4. Replace with a new spool.

NOTE

Make sure that the cutting line is in the guide slot on the new spool, and is extended approximately 5 in. before you install the new spool.

1. Put the end of the cutting line through the eyelet.
2. Extend the cutting line to release it from the guide slot in the spool.
3. Push the tabs and install the spool cover onto the spool housing.
4. Push the spool cover until it clicks into position.

6.4 REPLACE THE CUTTING LINE

Figure 13 - 16.

NOTE

Remove the remaining cutting line on the spool.

i NOTE

Use only with the nylon cutting line of 0.065" (1.65 mm) diameter.

1. Cut two pieces of cutting line approximately 3m long of each.

2. Bend one end of the line 1/4 of an inch (6.35mm).

3. Put the lines into the anchor holes of the spool.
4. Wind the cutting lines around the spool tightly in the indicated direction.
5. Put the cutting lines in the guide slots.
6. Do not wind the cutting line beyond the edge of the spool.

7 TRANSPORTATION AND STORAGE

7.1 MOVE THE MACHINE

When you move the machine, you must:

• Wear gloves.
• Stop the machine.
• Remove the battery pack and charge it.
• Assemble the blade guard.

7.2 STORE THE MACHINE

• Remove the battery pack from the machine.
• Make sure that children cannot come near the machine.
• Keep the machine away from corrosive agents such as garden chemicals and de-icing salts.
• Secure the machine during transportation to prevent damage or injury. Clean and examine the machine for any damage.

8 TROUBLESHOOTING

Problem Possible Cause Solution
The machine does not start when you push the trigger.	No electrical contact between the machine and the battery pack.	1. Remove battery pack.2. Check contact and install the battery pack again.
	The battery pack is depleted.	Charge the battery pack.
	The lock-out button and trigger are not pushed at the same time.	1. Pull the lock-out button and hold it.2. Pull the trigger to start the machine.

Problem Possible Cause Solution
The machine stops when you cut.	The guard is not attached to the machine.	Remove the battery pack and attach the guard to the machine.
	Heavy cutting line is used.	Use only with the nylon cutting line of 0.065" (1.65 mm) diameter.
	The grass winds around the motor shaft or the trim-mer head.	1. Stop the machine.2. Remove the battery pack.3. Remove the grass from the motor shaft and trimmer head.
	The motor is overloaded.	1. Remove the trimmer head from the grass.2. The motor will recov-er to work as soon as the load is removed.3. When you cut, move the trimmer head in and out of the grass to be cut and remove no more than 8" in pass.
	The battery pack or machine is too hot.	1. Cool the battery pack until its function returns to normal.2. Cool the machine for approximately 10 min-utes.
	The battery pack is disconnected from the tool.	Install the battery pack again.
	The battery pack is depleted.	Charge the battery pack.
The line does not forward.	Lines are welded to themselves.	Lubricate with silicone spray.
	Not enough line on spool.	Install more line.
	Lines are worn too short.	Advance the cutting line.
	Lines are tan-gled on spool.	1. Remove the lines from the spool.2. Wind the lines.
The line keeps breaking.	The machine is used incorrectly.	1. Cut with the tip of the line, avoid stones, walls and other hard objects.2. Advance the cutting line regularly to keep full cutting width.
The grass winds around the trimmer head and motor housing.	Cut tall grass at ground level.	1. Cut tall grass from the top down.2. Remove no more than 8" in each pass to prevent wrapping.
The line does not cut well.	The cut-off blade becomes dull.	Sharpen the cut-off blade with a file or replace it.
Vibration increases obviously.	The line is worn down at one side and not advanced in time.	Make sure that the line at two sides is normal. Advance the line.

9 TECHNICAL DATA

Voltage 24 V
No load speed 8400 /min
Cutting head Automatic feed
Cutting line diameter	0.065" (1.65 mm)
Cutting path diameter	10 in. (254 mm)
Weight (without battery pack)	1.7 kg
Measured sound pressure level	L_pA =71 dB(A), K_pA =3 dB(A)
Measured sound power level	L_wA =87.0 dB(A)
Guaranteed sound power level	L_wA.d =90 dB(A)
Vibration <2.5 m/s	^2 , k=1.5 m/s ^2
Battery model 29085	13/2908613/2908713/2908813

Noise value.

10 WARRANTY

(The full warranty terms and conditions can be found on Powerworks® webpage)

The Powerworks® warranty is 3 years on the product, and 2 years on batteries (consumer/private usage) from the date of purchase. This warranty covers manufacturing faults. A faulty product under warranty might be either repaired or replaced. A unit that has been misused or used in other ways then described in the owner's manual might be rejected for warranty. Normal wear, and wear parts are not considered as warranty. The original manufacturer warranty is not affected by any additional warranty offered by a dealer or retailer.

A faulty product must be returned to the point of purchase in order to claim for warranty, together with the proof of purchase (receipt).

11 EC DECLARATION OF CONFORMITY

Name and address of the manufacturer:

Name: Changzhou Globe Co., Ltd.

Address: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 China.

Name and address of the person authorised to compile the technical file:

Name: Peter Söderström

Address: Propellergatan 1, 211 15 Malmö, Schweden

Herewith we declare that the product

Category: String trimmer

Model: 2103613

Serial number: See product rating label

Year of Construction: See product rating label

• is in conformity with the relevant provisions of the Machinery Directive 2006/42/EC.
• is in conformity with the provisions of the following other EC-Directives:

• 2014/30/EU (EMC-Directive)
• 2000/14/EC (Noise Directive) incl. modifications(2005/88/EC)

Furthermore, we declare that the following (parts/clauses of) European harmonised standards have been used:

• EN 60335-1; EN 50636-2-91; EN 62233; EN 55014-1; EN 55014-2 EN ISO 3744; ISO 11904; EN ISO 11806-1.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

String trimmer

Measured sound power level: 87.0 dB(A)

Guaranteed sound power level: 90 dB(A)

Conformity assessment method to Annex VI / Directive 2000/14/EC.

Place, date: 10/11/2018

Signature: Ted Qu, Quality Director

Ted Gu

Deutsch

DE

Adresse: No. 65 (3-4) Xinggang Rd., Zhonglou

Zone, Changzhou 213101 China.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Faden-Rasentrimmer

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Cortabordes

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Decespugliatore

11 DÉCLARATION DE CONFORMITÉ CE

Adresse : No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 Chine.

• 2014/30/UE (Directive CEM)
• 2000/14/CE (Directive Bruit) modifications includes (2005/88/CE)

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

4.2 BEVESTIG DE BESCHERMING

Afbeelding 2 - 3.

WAARSCHUWING

Adres: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 China.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Grastrimmer

Gemeten geluidsvermogensni- 87,0 dB(A)

veau:

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Siimaleikkuri

Mitattu äänentehotaso: 87,0 dB (A)

6.1 ALLMÄNNA UPPLYSNINGAR

i VIKTIGT

7 TRANSPORT OCH FÖRVARING

7.1 FLYTTA MASKINEN

Adress: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101, Kina.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Trädtrimmer

5.5 TIPS FOR KLIPPING

Figur 8.

Adresse: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101, Kina.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Kantklipper

Målt lydeffektnivå: 87,0 dB (A)

Garantert lydeffektnivå: 90 dB (A)

Metode for samsvarsvurdering for Annex VI / direktiv 2000/14/EC.

Sted, dato: 10/11/2018

6.1 OBECNÉ INFORMACE

i DÜLEŽITÉ

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Strunová sekačka

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Strunová kosačka

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Kosilnica z nitko

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Trimer s plastičnom niti

Izmjerena razina snage zvuka: 87,0 dB(A)

Zajamčena razina snage zvuka: 90 dB(A)

Metoda procjene sukladnosti prema Dodatku VI direktive 2000/14/EZ.

Mjesto, datum 11.10.2018.

Potpis: Ted Qu, direktor za kvalitetu

Ted au

Magyar

HU

Cím: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 China.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Fükasza

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Кордов тример

Измерено ниво на сила на звука: 87,0 dB(A)

Adres: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101 Çin.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Aadress: No. 65 (3-4) Xinggang Rd., Zhonglou Zone, Changzhou 213101, Hiina.

ITS Testing & Certification, Davy Avenue, Knowlhill, Milton Keynes, MK5 8NL

Jõhvtrimmer