DW082 - Laser pointer DEWALT - Free user manual and instructions

USER MANUAL DW082 DEWALT

English (original instructions) 32

Technical diagram showing two battery mounting components with labeled parts 5 and 6, and a close-up inset of component 7.

B 8 C 2

1 V0

D

3

DANSK

KLASSE 3R LASERPRODUKT

DEWALT DW082 6.0 V mm 2 15 LARGE WIND WE WILL BE TREAT, LARGING LEARNING WITH SLASTIC TOLERANCE PULSE ON SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEE OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEA OR CHAMPATION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEa OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPION SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEb OR CHAMPIN SPEc OR CHAMPION SPEc OR CHAMPION SPEc OR CHAMPION SPEc OR CHAMPION SPEc OR CHAMPION SPEc OR CHAMPION SPEc OR CHAMPION SPEc OR CHAMPION

You have chosen a DeWALT tool. Years of experience, thorough product development and innovation make DeWALT one of the most reliable partners for professional power tool users.

Technical data

Voltage	V
Type
Battery size 4 x LR6 (AA)
Laser power mW < 1
Laser class 2
Wavelength nm 630 - 680
Protection class IP54
Self-leveling range ° +/- 4
Operating temperature °C 0 - 40
Receptacle thread 1/4" x 20
Weight	kg

Definitions: Safety Guidelines

The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

Denotes risk of electric shock.

ENGLISH

Denotes risk of fire.

Safety Instructions for Lasers

WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

• Do not operate the laser in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Use the laser only with the specifically designated batteries. Use of any other batteries may create a risk of fire.
• Store idle laser out of reach of children and other untrained persons. Lasers are dangerous in the hands of untrained users.
• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one laser, may create a risk of injury when used on another laser.
• Tool service MUST be performed only by qualified repair personnel. Repairs, service or maintenance performed by unqualified personnel may result in injury. For the location of your nearest authorized DEWALT repair agent, refer to the list of authorized DEWALT repair agents on back of this manual or visit www.2helpU.com on the Internet.
• Do not use optical tools such as a telescope or transit to view the laser beam. Serious eye injury could result.
• Do not place the laser in a position which may cause anyone to intentionally or unintentionally stare into the laser beam. Serious eye injury could result.
• Do not position the laser near a reflective surface which may reflect the laser beam toward anyone's eyes. Serious eye injury could result.
• Turn the laser off when it is not in use. Leaving the laser on increases the risk of staring into the laser beam.

ENGLISH

• Do not operate the laser around children or allow children to operate the laser. Serious eye injury may result.
• Do not remove or deface warning labels. If labels are removed user or others may inadvertently expose themselves to radiation.
• Position the laser securely on a level surface. Damage to the laser or serious injury could result if the laser falls.
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should also be avoided.

WARNING: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

WARNING! DO NOT DISASSEMBLE THE ROTARY LASER. There are no user serviceable parts inside. Disassembling the rotary laser will void all warranties on the product. Do not modify the product in any way. Modifying the tool may result in hazardous laser radiation exposure.

Additional safety instructions for lasers

• This laser complies with class 2 according to EN 60825-1: 2007. Do not replace a laser diode with a different type. If damaged, have the laser repaired by an authorised repair agent.
• Do not use the laser for any purpose other than projecting laser lines. An exposure of the eye to the beam of a class 2 laser is considered safe for a maximum of 0.25 seconds. Eyelid reflexes will normally provide adequate protection. At distances over 1m , the laser complies with class 1 and thus is considered completely safe.
• Never look into the laser beam directly and intentionally.
• Do not use optical tools to view the laser beam.
• Do not set up the tool at a position where the laser beam can cross any person at head height.
• Do not let children come in contact with the laser.

ENGLISH

- When you notice liquid leaking out, proceed as follows:

- Carefully wipe the liquid off using a cloth. Avoid skin or eye contact. Do not swallow.

- In case of skin or eye contact, rinse the liquid off with clean flowing water for at least 10 minutes and contact a doctor.

WARNING: Fire hazard! Avoid short-circuiting the contacts of a removed battery.

Residual Risks

The following risks are inherent to the use of this device:

- injuries caused by staring into laser beam.

Labels on tool

The following pictographs are shown on the tool:

Read the instruction manual before use.

Laser warning.

Do not stare into the laser beam.

Splashproof housing.

ENGLISH

DATE CODE POSITION

The Date Code, which also includes the year of manufacture, is printed on the inside of the battery compartment.

Example:

2010 XX XX

Year of Manufacture

Important Safety Instructions for Batteries

WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:

• Carefully follow all instructions and warnings on the battery label and package.
  • Always insert batteries correctly with regard to polarity (+ and -).

- Do not short battery terminals.

- Do not charge batteries.

• Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type.
• Remove dead batteries immediately and dispose of per local codes.

- Do not dispose of batteries in fire.

- Keep batteries out of reach of children.

- Remove batteries if the device will not be used for several months.

Batteries (fi g. B)

BATTERY TYPE

The DW082 operates on four LR6 (AA-size) batteries.

Package contents

The package contains:

1 Laser plumb bob

ENGLISH

4 Batteries
1 Kitbox (K-models only)
1 Instruction manual
- Check for damage to the tool, parts or accessories which may have occurred during transport.
- Take the time to thoroughly read and understand this manual prior to operation.

Description (fi g. A)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

1 On/off switch
2 Power indicator
3 Laser aperture (up laser beam)
4 Laser aperture (down laser beam)
5 Battery compartment

INTENDED USE

The laser plumb bob DW082(K) has been designed to project laser dots to aid in professional applications. The tool can be used both inside and outside for vertical (plumb) alignment.

DO NOT use under wet conditions or in presence of flammable liquids or gases.

This laser is a professional tool.

DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENT

WARNING: Do not place the laser in a position which may cause anyone to intentionally or unintentionally stare into laser beam. Serious eye injury may result from staring at the beam.

ENGLISH

Unpacking

FITTING THE WARNING LABEL

The safety warnings on the label shown on the laser must be formulated in the language of the user.

For that purpose, a separate sheet of self-adhesive labels has been supplied with the tool.

WARNING: Check that the safety warnings on the label have been formulated in your language.

The warnings should read as follows:

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 3R LASER PRODUCT

- If the warnings are in a foreign language, proceed as follows:

• Remove the required label from the sheet.
• Carefully place the label over the existing label.
• Press the label in place.

Replacing batteries (fi g. B)

The attachment uses batteries of type LR6 (AA).

• Open the battery compartment cover (5).
• Replace the batteries (6). Make sure the new batteries are placed as indicated.
• Close the battery compartment cover.

WARNING: When replacing batteries, always replace the

complete set. Do not mix old batteries with new ones.

Preferably use alkaline batteries.

Low battery indicator (fig. B)

The tool has been equipped with a low battery indicator (7) located on the control panel. The low battery indicator is lit while the tool is switched on. It will blink to indicate that the batteries need to be replaced and the tool will automatically shut down.

ENGLISH

- Switch off the tool and remove the batteries as soon as the indicator blinks.

Setting up the tool (fi g. C)

The tool has magnets (8) to hold it to steel floor track.

• Place the tool on a relatively smooth and level surface.
• Adjust the tool for a plumb application.

Adjusting the tool (fi g. C)

• To initiate the leveling procedure, switch on the tool. The plumb orientation is correctly adjusted as long as the laser beams remain on.
• The laser beams start flashing to indicate that the tool has been set up at a slope that is beyond the self-leveling range of 4^ . Switch the tool off, re-adjust the tool set-up within the self-leveling range and switch the tool on again.

Aligning the laser dot (fi g. C)

- Align the laser dot of either one of the laser beams with the position mark. Move the tool as required.

OPERATION

Instructions for use

WARNING: Always observe the safety instructions and applicable regulations.

• Always mark the center of the laser dots.
- Make sure the tool has been set up securely.
- Extreme temperature changes cause movement of internal parts that may affect the accuracy of the tool. Regularly check the accuracy while using the tool under these circumstances.
- Although the tool corrects small out-of-level errors automatically, when it is bumped, re-adjustment to balance or set-up may be required.
- If the tool has been dropped or has tipped over, have the laser head calibrated by a qualified repair agent.

ENGLISH

Switching on and off (fi g. D)

• To switch the tool on, press the on/off switch (1).
• To switch the tool off, press the on/off switch (1) again.

Transferring a position mark

The tool produces two laser dots in opposite directions to transfer a mark.

- Use the one beam to locate the mark and transfer the mark using the opposite laser beam.

Optional accessories

Consult your dealer for further information on the appropriate accessories.

MAINTENANCE

Your DeWALT laser unit has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper laser care and regular cleaning.

Field calibration check

The fi eld calibration check must be performed securely and accurately to make a correct diagnosis. Whenever an error is registered, have the tool calibrated by a qualifi ed repair agent.

WARNING: Always have the laser head calibrated by a qualified repair agent.

Plumb check

• Place the tool on the floor in an area parallel to a vertical surface of about 15 m height.
  • Mark a marking on the floor.
• Switch on the tool and align the laser beam with the floor marking.
  • Mark the centre of the laser dot on the ceiling.
• Switch off the tool and rotate it 180^ .
• Switch on the tool, align the laser beam with the floor marking and once again mark the centre of the laser dot on the ceiling. Switch off the tool.
  • Measure the difference between the markings.

ENGLISH

• If the difference between the markings is 6 mm or less, the laser head is properly calibrated.
• If the difference between the markings is more than 6 mm, the laser head must be calibrated.

Cleaning

• Remove the batteries before cleaning the tool.
• Keep the ventilation slots clear and regularly clean the housing with a soft cloth.
• When necessary, clean the lens using a soft cloth or a cotton bud soaked in alcohol. Do not use any other cleaning agents.

Protecting the Environment

Separate collection. This product must not be disposed of with normal household waste.

Should you find one day that your DeWALT product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection.

Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

DeWALT provides a facility for the collection and recycling of DeWALT products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf.

ENGLISH

You can check the location of your nearest authorised repair agent by contacting your local DeWALT office at the address indicated in this manual. Alternatively, a list of authorised DeWALT repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com.

Batteries

- When disposing batteries, think of the protection of the environment. Check with your local authorities for an environmentally safe way of battery disposal.

GUARANTEE

DeWALT is confident of the quality of its products and offers an outstanding guarantee for professional users of the product. This guarantee statement is in addition to and in no way prejudices your contractual rights as a professional user or your statutory rights as a private non-professional user. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.

• 30 DAY NO RISK SATISFACTION GUARANTEE •

If you are not completely satisfied with the performance of your DEWALT tool, simply return it within 30 days, complete with all original components, as purchased, to the point of purchase, for a full refund or exchange. The product must have been subject to fair wear and tear and proof of purchase must be produced.

• ONE YEAR FREE SERVICE CONTRACT •

If you need maintenance or service for your DeWALT tool, in the 12 months following purchase, you are entitled to one service free of charge. It will be undertaken free of charge at an authorised DeWALT repair agent. Proof of purchase must be produced. Includes labour. Excludes accessories and spare parts unless failed under warranty.

• ONE YEAR FULL WARRANTY •

If your DeWALT product becomes defective due to faulty materials or workmanship within 12 months from the date of purchase, DeWALT guarantees to replace all defective parts free of charge or – at our discretion – replace the unit free of charge provided that:

• The product has not been misused;
- The product has been subject to fair wear and tear;
• Repairs have not been attempted by unauthorised persons;
• Proof of purchase is produced;
- The product is returned complete with all original components.

If you wish to make a claim, contact your seller or check the location of your nearest authorised DeWALT repair agent in the DeWALT catalogue or contact your DeWALT office at the address indicated in this manual. A list of authorised DeWALT repair agents and full details of our after-sales service is available on the Internet at:

www.2helpU.com

ESPAÑOL

HILO DE PLOMADA DE LÁSER DW082(K)

¡ Enhorabuena!

DEWALT. DW082 6.0V 2 Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Security

DeWALT DW082 6.0 V 2 Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Safety Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Severity Security

L'emballage contient: