WS105 - Alarm system Chuango - Free user manual and instructions

Product type	Wireless alarm system
Brand	Chuango
Model	WS105
Dimensions (W x D x H)	90 × 90 × 42.2 mm (connector excluded)
Weight	Approximately 200 g
Power supply	100-240 V AC, 50/60 Hz
Backup battery	Lithium 3.7 V, 600 mAh, 2.22 Wh
Sound volume	90 dB
Radio frequency	433 MHz
Housing material	PC + ABS plastic
Operating conditions	Temperature: 0 °C to +55 °C; Humidity: < 80 % (non-condensing)
Maximum number of accessories	40
Entry/exit delays	30 s, 60 s or canceled (adjustable)
Strobe lighting	Yes, with indicator light
Standalone operation	Yes, without control panel
Wireless connection	With control panel and accessories (remote control, detectors, etc.)
Memory	E²PROM (non-volatile)
Maintenance	Clean with a soft, dry cloth. Do not use solvents.
Safety	Memory protection in case of power outage; deterrent siren
Spare parts and repairability	Wireless accessories available; parts not specified by the manufacturer

Frequently Asked Questions - WS105 Chuango

How to install the WS105 siren?

Plug the siren into a power outlet (100-240 V AC), then press the power switch. A long beep confirms power-up. You can then pair it with a control panel or wireless accessories.

How to pair the siren with a control panel?

Briefly press the connection button on the siren (0.5 s). After 3 seconds, a beep sounds and the strobe lights up. Then press the [SOS] or [Arm] button on the control panel. A beep confirms successful pairing.

How to connect wireless accessories (remote control, detector)?

Put the siren into connection standby mode by briefly pressing the connection button. Trigger the accessory (e.g., press a button on the remote control). A beep confirms the connection. You can connect up to 40 accessories.

How to delete all paired accessories?

Press and hold the connection button for 6 seconds until you hear a long beep. The indicator blinks twice, indicating that all accessories and control panels are cleared.

How to adjust the entry/exit delay?

Press the connection button twice for a 30-second delay, three times for 60 seconds, or four times to cancel the delay (default: no delay). During the delay, the siren beeps every 5 seconds.

Can the siren operate without a control panel?

Yes, the siren can be used in standalone mode by directly connecting wireless accessories. It then triggers the alarm when a detector is activated.

How to activate night lighting?

In standalone mode, press the [Home mode] button on the remote control twice within 3 seconds. The siren switches to silent mode and the night light turns on. Press [Disarm] to turn off.

What to do in case of a lost remote control?

For security reasons, delete all accessories (see question 4) then reconnect the remaining accessories. This excludes the lost remote control.

What is the backup battery life?

The 3.7 V / 600 mAh lithium battery provides approximately 8 hours of standby power during a power outage.

How to maintain the WS105 siren?

Clean the housing with a soft, dry cloth. Do not use chemicals or abrasives. Periodically check the proper operation of detectors and the siren.

USER MANUAL WS105 Chuango

2017 Chueng: All Rights Reserved.

Printed in China Voc:WS 105 JMI VLTD

CHUANGO

MULTILINGUAL

USER MANUAL

WS-105

Mini Strobe Siren

Features

1. Compact size with plug-in design
2. 100% wireless configuration, D.I.Y. Installation
3. Built-in 1,000,000 RF codes combination maintains high reliability
4. E² PROM information protection, power failure won't cause damage to data
5. Easy to pair automatically with accessories
6. Work with all kinds of our wireless accessories
7. Mute operation for night, not disturbing neighborhood
8. Built-in 3.7V 600mAh lithium battery enables 8-hour standby

Introduction

The wireless siren is powered by AC 100V ~ 240V, without need of wiring. According to different requirements, users can install more wireless sirens indoor in different places to deter the illegal intruders.

Multiple wireless sirens in different places can be wirelessly connected with the control panel to build a system. When the control panel receives alarm signals from detectors, wireless sirens will hoot and the strobe lights will flash.

The wireless siren can also be used as a control panel independently. According to different requirements, users can build up a standalone on-site alarm system by connecting new homo-frequency accessories with this siren.

Product Overview

① Power Switch/Connect Button
② Strobe Light
(3) Siren

Power On/Off

Power On

The siren is powered off in default setting. Plug the siren into AC power socket, and then press the power switch button. The siren is powered on after a long beep.

Power Off

Press connect button once under working status. Then press the connect button for 6 seconds until a long beep is heard. The siren is powered off.

Strobe Light Indication

When armed, the strobe light will be on after one flash. When disarmed, the strobe light goes out after two flas

Work as Wireless Siren

When it works as a wireless siren, the siren should be connected with wireless control panel in advance. When the control panel is alarming, the siren hoots and the strobe light flashes to deter illegal intruders.

Connect to Control Panel

Firstly, press the connect button (0.5 seconds), the wireless siren beeps once. 3 seconds later, it gives out another beep and the strobe light flashes, then the siren goes into connecting status. Secondly, press [SOS] or [Arm] button on the panel, the wireless siren and control panel are connected successfully after one beep. Press connect button again to exit connecting status after one beep.

Notes: Please don't trigger any accessory when connecting with the control panel.

Testing:

Press the [Arm] button on the remote control, if the built-in siren of control panel and wireless siren beep once, the connection is successful. If not, the connection fails, please reconnect them.

Work as Standalone Alarm

The siren can build up a standalone alarm system by adding wireless accessories.

When the siren is armed, if any sensor is triggered, the siren will hoot and strobe light will flash to deter illegal intruders.

Connect Wireless Accessories

Firstly, press the connect button (0.5 seconds), the wireless siren beeps once. 3 seconds later, it gives out another beep and the strobe light flashes, then the siren goes into connecting status. Secondly, trigger the wireless accessory once (such as press any button on the remote control / separate the transmitter and magnet of the door contact / press the test button of motion detector), and it will be connected after one beep. Repeat the above operation to connect other accessories.

Note: The siren supports up to 40 wireless accessories.

Testing:

Press the [Arm] button on the remote control, if the wireless siren flashes once, it means the connection of remote control is successful. Then trigger the sensor, siren will hoot. If not, the connection fails, please reconnect.

Delete All Accessories or Panels

If you lose the wireless accessories especially the wireless remote controls, it is recommended to delete all the accessories and then re-connect for safety.

Press down the connect button for 6 seconds until one beep is heard, at the same time, the LED indicator flashes twice, it means all connected accessories and panels are deleted.

Entry and Exit Delay

Entry and exit delay time can be set if you do not want to take the remote control.

After setup, if you arm the system, the siren beeps once every

5 seconds until it goes to arm state. If the detectors (except those in 24-H zone) are triggered, the siren will sound the alarm after the delay time. (Siren ringing time is 3 minutes). The setup method is as below:

Press Connect Button twice, delay 30 seconds.

Press Connect Button three times, delay 60 seconds.

Press Connect Button four times, no delay.

Default setting: No delay.

Note: Press the [Arm] button on the remote control twice, the system switches to arm state immediately.

Switch On/Off Night Lamp

When the siren working as a standalone alarm, it can also be used as a LED night lamp.

Press the [Stay] button on the remote control, its LED indicator blinks once, and then press the [Stay] button again within

3 seconds, the siren switches to home mode silently and the night lamp is on. Press [Disarm] button, the siren will be disarmed and the strobe light will be switched off.

Specifications

Power Supply: AC 100 V-240 V, 50/60 Hz

Volume: 90 dB

Backup Battery: 3.7 V 600 mAh lithium battery, 2.22 Wh

Static Current: <13 mA

Alarm Current: < 100mA

Radio Frequency: 433 MHz

Housing Material: PC+ABS plastic

Operation Condition:

Temperature: 0^ +55^

Relative Humidity: < 80% (non-condensing)

Dimensions: 90 × 90 × 42.2 mm (Plug part excluded)

Merkmale

Funkfrequency:433MHz

Radiofrequency:433 MHz