Timon - Bed Lionelo - Free user manual and instructions

USER MANUAL Timon Lionelo

CAREFULLY AND KEEP FOR

1. Do not use this product without reading the instrucons for

2. Stop using the product as soon as the child can sit or kneel

Placing addional items in the product may cause suocaon.

Do not place the product close to another product, which could present a danger of suocaon or strangulaon, e.g. strings, blind / curtain cords, etc.

5. Do not use more than one maress in the product.

6. Product should be placed on horizontal oor.

7. Young children should not be allowed to play unsupervised

in the vicinity of the crib.

The crib should be locked in the xed posion when the child is le unaended.

All assembly ngs should always be ghtened properly and care should be taken that no screws are loose, because a child could trap parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc) which would‑ 6 ‑EN pose a risk of strangulaon.

10. The maximum thickness of the maress is marked by a red

lining on the inside of the crib. Do not use a maress thicker than indicated.

Be aware of the risk of burning cigarees, open res and other sources of strong heat, such as electric bar res, gas res, etc. in the near vicinity of the crib.

DO NOT use crib if any parts are missing, damaged, or broken. Contact Lionelo for replacement parts and instruconal literature if needed. DO NOT substute parts. WARNING for maress:

Do not use the maress if any part is broken, torn, or missing, use only spare parts approved by manufacturer.

2. Intended for cots of maximum internal size 51 x 90 cm.

3. Do not use more than one maress in the cot.

4. Be aware of the risk of open re and other sources of strong

heat, such as electric bar res, gas res, etc. in the near vicinity of the cot. WARNING for bedside sleepers:

DO NOT use bedside sleeper if any parts are missing, damaged, or broken. Contact Lionelo for replacement parts and instruconal literature if needed. DO NOT substute parts.

The height from the oor of the adult’s bed for which the bedisde sleeper is suitable: 51 - 67 cm.

The bedside sleeper is intended for standard type adult beds only. Do not use the product with waterbeds or bed and mareses with rounded corners (g. 19).

8. Do not use aachment systems other that those described

9. Bedside sleepers shall never be used in an inclined posion.

To prevent a suocaon hazard from entrapment, the bedside sleeper shall be properly secured to the adult bed using the aachment system.

There shall never be a gap between the lower side of the‑ 7 ‑ EN bedside sleeper and the maress of the adult bed.

12. Check the ghtness of the aachment system before each use

by pulling the bedside sleeper in a direcon away from adult bed.

13. If there is a gap between the bedside sleeper and the adult

Gaps should not be lled with pillows, blankets and other items.

15. DANGER! Always completely raise the drop side when not

aached to the adult’s bed.

WARNING: To avoid hazards from the child’s neck being

caught on the top rail on the side that is next to the adult bed, the top rail must not be higher than the adult bed maress.

WARNING: To avoid risk of your child being strangled the

aachment system to the adult’s bed shall always be kept away from and out of the crib.

1. Take the frame and a base out of the packaging carefully and place them on

2. Part lower elements of the bed’s frame unl you can hear a disncve click.

Fasten the material under the bed’s base by wrapping a metal tube underneath the bed with Velcro bands (g. 7).

Li the tube and use snap fasteners to aach it to the top frame of the baby’s bed (g. 8).

6. Buckle on both sides of the opening side.

Press the wheels into the holes by the leg bases. They should engage automacally. When they do, you will hear a disncve click (g. 9).

In order to disassemble the wheels, press the buon (g. 20) with a at hard object. LOCKING MECHANISM Every wheel has a built-in locking mechanism. To lock a wheel, press the brake by‑ 8 ‑EN pulling the plasc level downwards (g. 11). NOTE! When using the baby’s bed, remember to lock all wheels.

BABY’S BED HEIGHT ADJUSTMENT

The baby’s bed height can be adjusted at 6 levels. The product’s height can be adjusted independently from each side, thanks to which it is possible to set an inclinaon. The height changing buons are located on both sides of the product, just under the top frame of the bed. To change the height, press the buon on one side of the bed, then li or lower the bed as desired. Do the same on the other side.

WARNING: The maximum permissible inclinaon of the baby’s bed is a dierence of

2 levels. The child’s head must always be higher than other parts of the body (g. 12). NOTE! Before you change the height of the maress, take the child out of the bed.

FUNCTION OF THE BEDSIDE SLEEPER

Timon baby’s bed can be used as an bedside sleeper (aached to parents’ bed). Before you use the product for this purposes, make sure the baby’s bed has been placed properly, and linking belts have been aached and tensed up as requested. The product must be aached to parents’ bed in a way that excludes any gaps between the product and the maress. When using, make sure the bedding, quilt, etc. do not take space in the bed. NOTE! It is allowed to use the product solely by the beds and/or maresses with straight sides. The use of the product by the round or water beds and/or maresses is forbidden. To make use of the bedside sleeper, prepare the product for such use properly. To do so, follow the points below:

1. Unzip on both sides of the opening side (g. 13)

2. Release the protecon by pressing the buons on the frame and slide the

metal frame tube out of the clips.

3. Push the baby’s bed closer to the parents’ bed.

4. Adjust the height of the cot (g. 14).

NOTE! When using the baby’s bed as an bedside sleeper, the height must be the same on both sides.

5. Use the belts to aach the baby’s bed to parents’ bed. Fasten the belt from

the internal side of the le and right frame, and then wrap around the bed’s frame and fasten it.‑ 9 ‑ EN

Tighten the belts and make sure the baby’s belt has been aached to parents’ bed properly. TRAP RISK In order to avoid trap risk, the baby’s bed must be secured properly and aached to parents’ bed as recommended. The product must be aached to parents’ bed in a way that excludes any gaps between the product and the maress. If this is impossible, do not use the product as a bedside sleeper. WARNING! Before each use, check that there is no gap between parents’ maress and the side wall of the baby’s bed. FALL RISK The baby’s bed is designed for children whose weight does not exceed 9 kg. Remember! Always li the side of the baby’s bed when it is not aached to the parents’ bed. NOTE! If the child can sit, kneel or pull itself, it should not use the baby’s bed anymore.

1. Take the maress out.

2. Set the height of the baby’s bed to level II.

3. Press both buons under the top frame of the baby’s bed at a me (on both

5. Fold in the boom of the bed.

6. Fold up the basket by liing it up.

Press the buon by the base to fold lower components of the bed’s frame (g. 18).

9. Do the same on the other side.

CLEANING AND MAINTENANCE

The product should be washed by hand using a mild detergent. Do not iron, do not tumble dry. Maress: machine wash at 60°C. The product has been tested and meets all the requirements of the following standards: EN 1130:2019+AC:2020, EN 16890:2017+A1:2021 The pictures in this manual are for illustrave purposes only. Therefore, they may dier from the actual product.‑ 10 ‑PL