M01776 - Battery charger Brüder Mannesmann - Free user manual and instructions

Product type	Battery charger / Jump starter
Brand	Brüder Mannesmann
Model	M01776
Internal battery	Lead-acid rechargeable, 7 Ah
Nominal voltage	12 V
Starting current (peak)	600 A
Integrated compressor	Yes, max pressure 18 bar (260 psi)
LED work light	Yes
USB port	Yes, 5 V / 1 A
12 V socket	Yes, for accessories
Jump cables	With clamps, rubber insulation, copper conductors
Mains charger included	Yes, 230 V~ / 50 Hz
Cigarette lighter charger included	Yes
Charging time (mains)	Approximately 12 hours
Charge display	Green LED
Reverse polarity protection	Yes, audible and visual alarm
Dimensions (approx.)	300 x 200 x 250 mm
Weight (approx.)	5 kg
Warranty	2 years
Usage	Non-professional (domestic)

Frequently Asked Questions - M01776 Brüder Mannesmann

How to fully charge the Brüder Mannesmann M01776 before first use?

Plug the mains charger (15) into a 230 V~ / 50 Hz socket and connect the small plug to the charging socket (9) on the front of the device. Wait approximately 12 hours. The LED (10) lights up green when charging is complete. Ensure the main switch (1) is in the OFF position during charging.

How to use the jump start function for a 12 V vehicle?

Make sure the vehicle engine is off. Connect the RED clamp to the positive terminal of the battery, then the BLACK clamp to a fixed metal ground in the engine compartment (never on the negative terminal). Turn on the main switch (1) and wait 3 to 5 minutes. Try starting the engine for a maximum of 5 to 6 seconds. If necessary, wait 3 minutes before another attempt. After starting, remove the black clamp first, then the red.

What to do if the clamps are connected incorrectly?

In case of reverse polarity, the reverse polarity LED (7) lights up and an audible alarm sounds. Disconnect the clamps immediately and reconnect them correctly: red to positive (+), black to a metal ground (never to the battery negative).

Can I use the compressor to inflate car tires?

Yes. Attach the hose connector (14) to the tire valve and flip the clamping lever. Turn on the compressor (13) and monitor the pressure gauge (12). Turn off when the desired pressure is reached. Do not let the compressor run for more than 10 minutes continuously; let it cool for 10 minutes if needed.

What accessories are provided for inflation?

The device comes with a valve adapter (17) to inflate balloons, toys or sports equipment. Insert the adapter into the hose connector and flip the clamping lever before turning on the compressor.

How to use the USB output?

Plug your USB device into the USB port (6). The switch (8) activates or deactivates the voltage. The output delivers max 5 V / 1 A. The green LED lights up when the output is active. Note that this is not a data port.

Can I charge the device with my car's cigarette lighter?

Yes. Use the supplied cigarette lighter charging cable (16). Plug the cigarette lighter plug into the vehicle's socket, and the small plug into the charging socket (9) of the M01776. Do this only during a trip to avoid draining the car battery.

What safety precautions should be observed?

Protect the device from moisture, extreme temperatures and dust. Wear safety glasses when working with lead-acid batteries. Avoid contact with battery acid. Do not short-circuit the clamps. Use only in a well-ventilated area. Do not use the device near flammable gases or liquids.

How to maintain the internal battery if the device is not used for a long time?

The battery discharges naturally. To preserve its lifespan, recharge the device every 3 to 5 months, even if not in use. Use only the supplied charger.

What to do in case of a problem or defect?

First consult the complete manual. If the problem persists, contact Brüder Mannesmann customer service by phone at +49 2191/37 14 71, by fax at +49 2191/38 64 77, or by email at [e-mail]. The device is guaranteed for 2 years from the date of purchase, subject to proper use.

USER MANUAL M01776 Brüder Mannesmann

Exterior view of a Bruder Manesmann WERKZEUGE charging device with two clamp clips (no visible text or symbols on body)

DE

Please read and understand this manual, before starting to work with this equipment! Save this manual for any later reference.

The Jump Start System is suitable for emergency-start of your vehicle with 12V electrical system, for inflating tires of cars, motorcycles, bicycles etc., balls and other inflatable sports- or playthings and as power-supply for 12V-tools. In addition, a LED work lamp and a USB output are integrated.

The system has not been designed for commercial use.

Safety-warnings and precautions

1. Check the quick start system for damage prior to every use! Faulty or damaged parts must be properly repaired and replaced by a customer service workshop.
2. The device must be protected from rain, splash water and humidity!
3. Avoid direct sunlight, extreme heat or cold and keep the device away from dust and dirt.
4. Operation, charging of the battery and storing only on acid-resistant surface!
5. Use and store the Jump starter exceptionally In upright position.
6. Wear eye-protection when working on or around lead-acid batteries.
7. Avoid contact with battery acid. If splashed, immediately wash effected area with clean water. Continue washing area, until medical help arrives.
8. Connect cables to proper polarities. Turn vehicle ignition OFF, before making cable connections. Connect RED (POSITIVE) cable to positive battery terminal first, then connect BLACK (NEGATIVE) cable to body ground (a non-moving metal part) second. Do not connect the BLACK NEGATIVE cable to the negative battery terminal.
9. Use this tool in well ventilated areas. Do not attempt to jump-start vehicle around flammable gases or liquids.
10. Do not allow the black and red clamps to touch. If this happens, it can melt clamps or other metal objects. Place them only on the corresponding terminals.
11. Use only with vehicles and boats with 12 volt electrical systems.
12. For emergency use only. Do not use this system in the place of a vehicle battery. Only use to jump-start your vehicle.
13. The Jumpstart system must only be used for purposes, described and written in this manual.

Important

• The energy station comes with a partially charged battery.
• The battery needs to be fully charged before the unit is used for the first time!
• The battery discharges automatically when the energy station is not used for a long time. In order to preserve the operating life of the battery, it should be recharged at least once every 2-3 months, irrespective of the amount of usage.
• Use only the supplied power supply unit for charging purposes.

Technical details

Battery Type: Sealed, lead-acid, rechargeable, 7 amp-hours

Power Output: 12 VDC, 300 amps starting power (600 A peak)

Cables: Rubber insulated (#4) copper;

Compressor: 260 PSI (18 bar) maximum pressure

Output Socket: 12 VDC cigarette lighter output

Discription

1. Main switch
2. LED working-light
3. Carrying handle
4. 12V= outlet
5. Booster clamps
6. USB-port
7. Voltage reversal indicator
8. On-/off-switch for working-light and USB-port
9. Loading-socket
10. Loading indicator
11. Voltage checking button
12. Pressure meter
13. On-/off-switch for compressor
14. Pressure hose
15. Charging-adaptor 230V\~/50Hz
16. Loading-adaptor for cigarette-lighter
17. Inflating-adaptors

Features: - AC/DC power pack

- inflating needle and air raft tips

- LED working light

Operation

Warning: Electrical shock can cause death or injury. Avoid touching exposed conductors of electricity.

The Jumpstart System is designed only for use with vehicles and boats with 12V-system. You can also use this system as a portable power supply of 12 VDC in remote areas or emergencies.

To use the Jumpstart to start your vehicle

1. Make sure the vehicle or boat to be jump-started is not running and set the ignition „OFF“.
2. Do not allow the black and red clamps (5) to touch. If this happens, it can melt clamps or other metal objects.
3. Connect the RED clamp to the POSITIVE (+) terminal on the vehicle's battery.
4. Connect the BLACK clamp to a non-moving metal part of the engine, not to the negative terminal of the battery.
5. In the event of improperly connected pole clamps, the LED (7) flashes red and a warning signal is triggered.

6. Pay attention to the clamps being sufficiently fixed on the terminals.

7. Switch on the quick start system by turning the main switch (1) and wait for 3 to 5 minutes.

8. Switch the vehicle ignition to the „ON“ position.
9. Switch the ignition to the start position for no more than 5 to 6 seconds.
10. If the vehicle or boat engine does not start, wait at least 3 minutes before re-trying.
11. When the engine is running, disconnect the black clamp first and return the cable to its stored position on the jumpstart system.
12. Disconnect the red clamp and return the cable to its position on the system.
13. Recharge the Jump Start system as soon as possible. You can only perform an emergency start if the quick start system is fully charged.
14. The quick start system is not suitable for starting completely discharged batteries!

To use your Jump Start System to power appliances:

1. Lift up the cover of the cigarette lighter receptacle (4).
2. Insert the cigarette lighter plug of the appliance into the cigarette lighter receptacle and connect to your 12V-tool.

USB output

At the USB port (6), small loads with a USB plug may be operated. The USB port delivers 5 Volt with up to 1000 mA and is not a data port. With the switch (8), the voltage on the port can be switched on or off. The operating status is indicated by the green LED.

Compressor Operation

1. If inflating a tire, place the hose connector on the tire valve stem and press the connector lever down to lock in place.
2. If inflating a ball, air mattress or other item, place the inflation needle or plastic adapter (17) into the hose connector end, press the connector lever down to lock in place.
3. Turn the compressor power switch (13) to the „ON“ position.
4. Note: Do not over-inflate item. Check pressure gauge (12) and stop inflating, when adequate pressure is reached.
5. Only run the compressor for 10 minutes at a time. If more air is needed, wait 10 minutes for cooling down, before using again.

Recharging

This unit is rechargeable by either the re-charging adapter or by use of a vehicle 12 VDC cigarette lighter output socket. It is recommended that the battery is kept fully charged at all times. (Caution! Put the main switch (1) in the “OFF” position.)

If the battery is left in a low charge state, it could shorten battery life. The time required to recharge the battery depends on the number of previous battery jump starts. To check and see if the battery is low, press the red button (11). When the LED (10) flashes green, the quick start system is sufficiently charged.

To re-charge using the adapter

1. Plug the adapter cord connector into the receptacle (9) on the front panel.
2. Put the charging-adaptor (15) into a 230 V\~ outlet.
3. Allow the Jump Start System to recharge about 12 hours. Check the re-charge progress by pressing the red button (11).
4. When the LED (10) flashes green, the quick start system is sufficiently charged.

To recharge using a 12 VDC supply:

Note: Recharging with this method will not recharge the system to the same 14 to 15 VDC voltage level, as when using the AC-adapter.

1. Insert the cigarette lighter recharger cord plug (16) into the cigarette lighter receptacle on the boat or vehicle.
2. Insert the other end of the cigarette lighter recharger cord (small plug) into the receptacle (9) on the front panel of the unit.
3. You should only charge the energy station when en route, as otherwise the unit will run down the vehicle's battery.

Battery disposal

- After the battery in the jump start system has expired, it must be recycled. Some countries requires this recycling. Contact the local solid waste authority for recycling information.

• Caution: Do not dispose of battery by fire. This could result in explosion.
• Before disposing of battery, cover exposed terminals with heavy duty insulation tape to prevent short-circuit.

2 years warranty

The warranty for this tool starts at the date of purchase. Please provide your purchase bill as proof.

This warranty includes:

• repair of operational failures
- replacement of faulty parts
• qualified service and installation

provided that the failure does not result of wrong handling.

Please do not hesitate to contact us for any further queries:

Old Power Tools and Protection of the Environment

• If your power tool has been so heavily used that it has become worn out and has to be replaced, or you have no further use for it, you must turn the power tool in at a central recycling centre for disposal.
• Please contact your community waste collection service or local authority to find out where you can hand in your tool for disposal.
• Power tools contain valuable raw materials that can be recycled. You will contribute to recycling valuable raw materials by handing your tool in at a central waste disposal centre.
• Power tools also contain substances that may be harmful to the environment and humans if disposed of inappropriately.

- The no-go sign with the dustbin means that you have a duty to take that article with the sign to be recycled by a separate waste collection facility for electrical and electronic equipment.