IAN 351982 - Inflatable pool Playtive - Free user manual and instructions

USER MANUAL IAN 351982 Playtive

• Warning. None of the packaging and fastening materials are considered part of the toy and must always be removed for safety reasons before the product can be given to children to play with. Danger to life!

• Children can drown in very small amounts of water. Empty the pool when not in use. Risk of injury!

• Do not allow your child to use the product un- supervised since children are unable to judge potential dangers. Use only under the direct supervision of an adult.

• Do not place hard objects with sharp edges, e.g. toys, in the pool while it is in use. Do not wear or carry jewellery, watches or keys. Take off your shoes or your child’s and remove glasses if worn.

• To protect against damage to the product and injuries to people the product may not be used until it is fully inflated.

• Children may not jump into the pool.8

• Speak to your children about how to use the product while playing safely.

• Do not modify the product in any way.

• Use only clean tap water. Contaminated water can endanger the health of users.

• Adult assembly required.

• Do not install the paddling pool over con- crete, asphalt or any other hard surface.

• The product should be assembled on a flat lawn without any stones, sticks, bumps or hollows. Please ensure that the product is at an appropriately safe distance of at least two metres away from buildings, steps, fences, walls, waterways, overhanging branches, washing lines, electrical cables, and any other obstacles.

• Check the product for damage and wear be- fore each use. The product may only be used in good order and condition!

• Do not use the product if air is leaking.

• Do not use the product without the slide inflated.

• Children may only play with the product under adult supervision. Avoiding material damage!

• All inflatables are susceptible to cold. For this reason never unfold and inflate the product at a temperature lower than 15°C!

• Warning. Avoid the use of sunscreen and skin care products containing alcohol. Sunscreen and skin care products containing alcohol may dissolve the colour coating of the inflatable PVC items. This can lead to discolouration on your body, your clothing, or on other objects which come into contact with the product.

• In the event that the air pressure increases in the hot sun, it must be balanced accordingly by letting out air.

• Make sure that the product, especially when inflated, does not come into contact with stones, gravel, or sharp objects and does not rub or scrape against anything as this can cause damage to the plastic foil.

• Use only the correct pump adapters to insert into the safety valves. The valves might other- wise be damaged.

• Do not over-inflate because you then risk tear- ing open the welded seams. Close the valves properly after inflating.

• Avoid contact with sharp-edged, hot, pointed, or dangerous objects. Assembly An adult should always assemble the product. Please follow the individual assembly steps in the order indicated.

1. Selecting the location

Choose a suitably flat and clean surface with plenty of space to unpack and unfold the prod- uct. Spread the product out in the place where it will later be used. Check that all individual parts are present and in good order and condition.

• Always inflate the air chambers fully!

• Avoid inflating the air chambers too much because there is the risk of over- stretching the welded seams or even tearing them open.

• Use standard commercial foot pumps or double-stroke piston pumps with matching adapter attachments to inflate the product.

• Do not use a compressor or com- pressed air bottles to inflate the product. This can lead to damage to the product.

• Make sure that the chambers are filled with air uniformly. GB/IE9

• Inflate each air chamber until it feels firm to the touch. When you press with your thumb against the air cham- ber it should still give a little. Sequence WARNING! Follow the correct sequence when inflat- ing the air chambers. Always inflate all air chambers fully.

1. Main chamber (1a)

2. Slide with side walls (1b)

1. Fill the main chamber (1a) with air and close

the cap (fig. B). Inflate the air chamber until it feels firm to the touch. When you press with your thumb against each air chamber it should still give a little. Close the valve seal.

2. To fill components 1b-1e and 2-5 open the

valve seal and inflate the air chambers. Close the valve seal and push in the valve by press- ing lightly (fig. C).

4. Garden hose connection

To connect a garden hose use a suitable hose coupling and attach it to the product’s water connection (fig. D). Filling the product with water Fill the product slowly and do not leave it unat- tended while filling. Note: Fill the product up to, at most, the printed mark. Important! Do not exceed the filling capacity of 165l without water sprayer attached! Emptying the product Open the drainage hole and allow the water to run out (fig. E). Note: Please follow the local regula- tions regarding specific requirements for disposing of water from swimming pools. Disassembly Allow the product to dry completely before folding it up. Remove the garden hose. Take off all individual removable parts. Deflating the product

1. To deflate the main chamber rapidly, open the

2. To deflate the other components pull out the

valve and squeeze the valve stem lightly so that the air can escape or insert the deflation tube into the seal to allow the air to escape rapidly. Repairs Minor leaks or holes can be repaired with the repair patch supplied. Important! Do not inflate the product for 20 minutes after repair! Do not use the repair patch for leaks or holes on the seam.

1. Let the air out of the product completely.

2. Clean the area around the leak thoroughly.

The area must be dry and free from grease. GB/IE10

3. Cut out a piece of the repair material that is

big enough for its edges to overlap the dam- aged area by about 1.3cm.

4. Peel the repair patch off the paper, place it on