IAN 331515_1907 - Uncategorized Playtive - Free user manual and instructions

USER MANUAL IAN 331515_1907 Playtive

• Children can drown in very small amounts of water. Empty the pool when not in use. Risk of injury!

• Do not allow your child to use the product un- supervised since children are unable to judge potential dangers. Use only under the direct supervision of an adult.

• Objects that are hard and have sharp edges, e.g. toys, should not be in the pool when it is being used. Do not wear or carry jewellery, watches or keys. Take off your shoes or your child’s and remove glasses if worn.

• To protect against damage to the product and injuries to people the product may not be used until it is fully inflated.

• Children may not jump into the pool.

• Speak to your children about how to use the product while playing safely.

• Do not modify the product in any way.

• Use only clean tap water. Contaminated water can endanger the health of users.

• Adult assembly required.

• Do not install the paddling pool over con- crete, asphalt or any other hard surface.

• The product should be assembled on a flat lawn without any stones, sticks, bumps or hollows. Please ensure that the product is at an appropriately safe distance of at least two metres away from buildings, steps, fences, walls, waterways, overhanging branches, washing lines, electrical cables, and any other obstacles. GB18 GB

• Check the product for damage or wear before each use. The product may be used only when in good working order and condition! Do not use the product when there is visible or suspected damage.

• Do not use the product if air is leaking.

• Do not use the product without the slide inflated. Avoiding material damage!

• All inflatables are susceptible to cold. For this reason never unfold and inflate the product at a temperature lower than 15°C!

• Avoid using sunscreen and skin-care products containing alcohol. Sunscreen and skin-care products containing alcohol can cause the colour coating of this PVC inflatable product to peel. This can lead to stains on your body, your clothing and other objects that are in contact.

• In the event that the air pressure increases in the hot sun, it must be balanced accordingly by letting out air.

• Make sure that the product, especially when inflated, does not come into contact with stones, gravel, or sharp objects and does not rub or scrape against anything as this can cause damage to the plastic foil.

• Use only the correct pump adapters to insert into the safety valves. The valves might other- wise be damaged.

• Do not over-inflate because you then risk tea- ring open the welded seams. Close the valves properly after inflating.

• Avoid contact with sharp-edged, hot, pointed, or dangerous objects. Assembly An adult should always assemble the product. Please follow the individual assembly steps in the order indicated.

1. Selecting the location

Choose a suitably flat and clean surface with plenty of space to unpack and unfold the product. Spread the product out in the place where it will later be used. Check that all indivi- dual parts are present and in good order and condition.

• Always inflate the air chambers fully!

• Avoid inflating the air chambers too much because there is the risk of over-stretching the welded seams or even tearing them open.

• Use standard commercial foot pumps or double-stroke piston pumps with matching adapter attachments to inflate the product.

• Do not use a compressor or com- pressed air bottles to inflate the product. This can lead to damage to the product.

• Make sure that the chambers are filled with air uniformly.

• Inflate each air chamber until it feels firm to the touch. When you press with your thumb against the air cham- ber it should still give a little. Sequence WARNING! Follow the correct sequence when infla- ting the air chambers. Always inflate all air chambers fully.

1. Main chamber (1a)

2. Slide with side walls (1b)

8. Aquatic plant (5)

cap (fig. B) Inflate the air chamber until it feels firm to the touch. When you press with your thumb against each air chamber it should still give a little. Close the valve seal.

2. To inflate components (1b) - (7) open the val-

ve seal and inflate the air chambers. Close the valve seal and push in the valve by pressing lightly (fig. C).19 Note: For better positioning first fill the bases of the moray eel (2), aquatic plant (5) and jellyfish (4) with water and then inflate them.

4. Connecting the garden hose

To connect a garden hose use a suitable hose coupling and attach it to the product’s water connection (fig. D). Filling the product with water Fill the product slowly and do not leave it unat- tended while filling. Always fill the product up to the marking shown. Important! Do not exceed the filling capacity of 300l without water sprayer attached! Emptying the product Open the drainage hole and allow the water to run out (fig. E). Note: Please follow the local regula- tions regarding specific requirements for disposing of water from swimming pools. Disassembly Allow the product to dry completely before folding it up. Remove the garden hose. Take off all individual removable parts. Deflate the product as follows:

1. To deflate the main chamber rapidly, open the

2. To deflate the other components pull out the

valve and squeeze the valve stem lightly so that the air can escape or insert the deflation tube into the seal to allow the air to escape rapidly. Repairs Minor leaks or holes can be repaired with the repair patch supplied. Important! Do not inflate the product for 20 minutes after repair! Do not use the patch for leaks or holes on the seam.

1. Let the air out of the product completely.

2. Clean the area around the leak thoroughly.

The area must be dry and free from grease.

3. Cut out a piece of the repair material that is

big enough for its edges to overlap the dama- ged area by about 1.3cm.

4. Peel the patch off the paper, place it on the

damaged area and press tight. Storage, cleaning Exchange the water in the product frequently, es- pecially in hot weather and if it is soiled. When not in use, always store the product clean, dry and uninflated at room temperature. The valves should always be closed during storage. Clean the product only with water or soapy water, never with abrasive detergents. When storing for the winter do not put any sharp objects on the product and do not apply talcum powder. Disposal Dispose of the article and the packaging materi- als in accordance with current local regulations. Packaging materials such as foil bags are not suitable to be given to children. Keep the pack- aging materials out of the reach of children. Dispose of the products and the packaging in an environmentally friendly manner. The recycling code is used to identify various materials for recycling. The code consists of the recycling symbol – which is meant to reflect the recycling cycle – and a number which identifies the material. Notes on the guarantee and service handling The product was produced with great care and under constant supervision. You receive a three- year warranty for this product from the date of purchase. Please retain your receipt. The warranty applies only to material and workmanship and does not apply to misuse or improper handling. Your statutory rights, espe- cially the warranty rights, are not affected by this warranty. With regard to complaints, please contact the following service hotline or contact us by e-mail. Our service employees will advise as to the subsequent procedure as quickly as possible. GB20 GB We will be personally available to discuss the situation with you. Any repairs under the warranty, statutory guar- antees or through goodwill do not extend the warranty period. This also applies to replaced and repaired parts. Repairs after the warranty are subject to a charge. IAN: 331515_1907 Service Great Britain Tel.: 0800 404 7657 E-Mail: deltasport@lidl.co.uk21222312.16.2019 / AM 11:35