GH227 - Soup maker BUFFALO - Free user manual and instructions

USER MANUAL GH227 BUFFALO

Model • Modèle • Modell • Modello • Modelo • Malli: GH227UK Safety Tips Position on a flat, stable surface A service agent / qualified technician should carry out installation and any repairs if required. Do not remove any components or service panels on this product Consult Local and National standards to comply with the following: o Health and safety at work legislation o BS EN Codes of practice o Fire Precautions o IEE wiring regulations o Building regulations DO NOT use jet / pressure washers to clean the appliance DO NOT use the appliance outside DO NOT use the appliance to store medical supplies DO NOT use electrical appliances inside the appliance (e.g. heaters, ice-cream makers etc) DO NOT allow oil or fat to come into contact with the plastic components. Clean immediately if contact occurs DO NOT store products on top of the appliance Always carry, store and handle the appliance in a vertical position and move by holding the base of the appliance Always switch off and disconnect the power supply to the unit before cleaning Keep all packaging away from children. Dispose of the packaging in accordance with the regulations of local authorities If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Product Description GH227 Buffalo 5.7L Cylindrical Soup Kettle Pack Contents Body Assembly Kettle Liner Top Ring Lid Assembly Installation Remove all packaging and dispose of safely. Wash Liner, Top Ring and Lid in warm soapy water, rinse in clean water then dry thoroughly. Operation Place the plug in the electric socket to connect electricity. Partly fill the Body with water (water level should be between the Min and Max fill lines). Place the metal collar on the body of the kettle, then place the inner liner inside the Body of the soup kettle (The inner liner should sit on top of the metal collar). Pour the hot soup or food in to the Liner, then position the Lid on the Top Ring. Switch on electricity at socket. Start heating by rotating the control knob clockwise, indicator light will come on and stay on until holding temperature selected is reached. Power will come on to start heating again when the temperature of the kettle falls.Telephone Helpline: 0845 146 2887 UK Cleaning, Care & Maintenance Disconnect from electricity supply, allow to cool before emptying the water from the Body, always use fresh water when the kettle is to be used. Always wash the Kettle Liner, Top Ring and Lid after every use. Wipe both exterior and interior of the Body to remove any food residues, do not immerse the Body in water or clean with a pressure washer. Trouble Shooting Technical Specifications Code Voltage Power Watts Current Amps Dimensions mm Weight Kgs GH227 230V/50Hz

Electrical Wiring This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 3 amp fuse as standard. The plug is to be connected to a suitable mains socket. The appliance is wired as follows: o Live wire (coloured brown) to terminal marked L o Neutral wire (coloured blue) to terminal marked N o Earth wire (coloured green/yellow) to terminal marked E This appliance must be earthed, using a dedicated earthing circuit. If in doubt, consult a qualified electrician. Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible Disposal The WEEE logo on this product or its documentation indicates that the product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your areaUK Compliance BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent and federal authorities BUFFALO products have been approved to carry the following symbol: