B127002D2H - Audio Visual Accessory Tripp Lite - Free user manual and instructions

USER MANUAL B127002D2H Tripp Lite

• Support 4K video resolution (3840 x 2160 @ 60 Hz) and 4:4:4 chroma subsampling

• Support up to 7.1-channel surround sound audio

• DisplayPort 1.2a compatible

• Supports up to 8-channel LPCM, AC-3, DTS digital audio

• Plug and play—no software or drivers required B127-1A1-DH

• DisplayPort over Cat6 Power-over-Cable (PoC) Extender Kit

• Extends a 4K (3840 x 2160 @ 60 Hz) signal up to 125 ft. (38 m) from the source

• Additional HDMI port on the local transmitter unit allows connection of a local monitor

• Remote receiver unit features built-in equalization (EQ) control and auto EDID image adjustment

Includes mounting hardware that allows both the local transmitter and remote receiver units to be wall-mounted, rack-mounted or pole-mounted B127-002-D2H

• DisplayPort over Cat6 Power Over Cable (PoC) 2 Port Splitter/Extender Kit

• Extends a 4K (3840 x 2160 @ 60 Hz) signal up to 125 ft. (38 m) from the source

• Remote HDMI receiver units feature built-in equalization (EQ) control and auto EDID image adjustment

• Kit includes a 2-port splitter extender and two remote receivers

• Includes mounting hardware that allows unit to be wall-mounted, rack- mounted or pole-mounted4 Product Features B127-004-D4H

• DisplayPort over Cat6 Power over Cable (PoC) 4-Port Splitter/Extender Kit

• Extends a 4K (3840 x 2160 @ 60 Hz) signal up to 125 ft. (38 m) from the source

• Remote HDMI receiver units feature built-in equalization (EQ) control and auto EDID image adjustment

• Kit includes a 4-port splitter extender and four remote receivers

• Includes mounting hardware that allows unit to be wall-mounted, rack- mounted or pole-mounted

• Additional HDMI port on the local transmitter unit allows connection of a local monitor B127-008-D

• DisplayPort over Cat6 Power over Cable (PoC) 8-Port Local Transmitter Unit

• Extends a 4K (3840 x 2160 @ 60 Hz) signal up to 125 feet (38 m) from the source to up to eight receivers

• Includes mounting hardware that allows unit to be wall-mounted, rack- mounted or pole-mounted

• Additional HDMI port on the local transmitter unit allows connection of a local monitor Optional Accessories:

• P580-XXX DisplayPort Cables5 Disclaimer Before installation, please check the following settings of your source(s) and TV/monitor(s):

1. Set monitor to display at 60 Hz. Double-check factory settings, as

default may be set to a lower frequency (Hz).

2. Ensure your monitor’s input setting is set to HDMI 2.0. Some displays

may have a default setting of HDMI 1.4

3. Verify your monitor has the HDR feature enabled. Some displays may

have this feature disabled as a default setting.

4. Check if the Ultra HD (UHD) Deep Color setting is enabled on your TV/

monitor. Confirm with your TV/monitor manufacturer which HDMI ports support UHD Deep Color. Note: If you wish to connect a local monitor to your installation, depending on the make/model of your TV or monitor, the UHD Deep Color setting may need to be disabled on your local TV/monitor to achieve 4K 60 Hz resolution.6 Mounting Instructions (select models) The B127-1A1-DH, B127-002-D2H, B127-004-D4H and B127-008-D include mounting hardware, allowing for a variety of mounting methods. The following images illustrate how the included mounting brackets can be attached for different installations. Note: The model shown in the below images is for illustrative purposes only. Your product may vary by model number, size or port orientation. The mounting options for all over IP units are the same. Wall-mount 19” Rack-mount Pole-mount7 Standard Extender Kit Installation Notes:

• Test to ensure the entire installation works properly before pulling cables through ceilings/walls.

• To achieve maximum distance and performance, use 24 AWG solid-wire Cat6 cable. Using stranded-wire Cat6 cable, or cable with a gauge (AWG) size higher than 24 AWG will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling. All Tripp Lite N202-Series Cat6 cables use 24 AWG solid-wire cabling.

• The installation diagram shows a B127-1A1-DH unit.

• External power is not required for the remote receiver due to Power over Cable (PoC) technology incorporated in the transmitter unit. B127-1A1-DH Extender Kit MONITOR PC LOCAL TRANSMITTER REMOTE RECEIVER Up to 125 ft. (38 m) at 4K/60 Hz Up to 125 ft. (38 m) Cat6 cable at 4K/60 Hz Up to 15 ft. (4.5 m) HDMI 2.0 cable at 4K/60 Hz Up to 15 ft. (4.5 m) DisplayPort cable at 4K/60 Hz

1. Make sure all equipment in the installation—such as TVs, Blu-ray

players and the transmitter—is powered OFF.

2. Using DisplayPort cables (such as Tripp Lite P580-XXX-Series),

connect the DisplayPort source to the INPUT port on the B127-1A1-DH local transmitter unit.

3. Optional for B127-1A1-DH: Using an HDMI 2.0 cable (such as

to the RJ45 port on the remote receiver unit.

5. Using an HDMI 2.0 cable (such as Tripp Lite P569-XXX-CERT or

P568-XXX-2A-Series cable), connect the remote receiver unit’s HDMI port to a monitor.

6. Power on all connected displays. The LOCAL (orange) LED will

illuminate to indicate the local port is connected to a display.

Connect the external power supply to the local transmitter unit and plug it into an available wall outlet or (optional) a Tripp Lite Surge Protector, Power Distribution Unit (PDU) or Uninterruptible Power Supply (UPS). The POWER (green) LED will illuminate to indicate the unit is receiving power from the external power supply. The POWER (green) LED on the remote receiver unit will illuminate to indicate the unit is receiving power from the local transmitter unit by way of PoC technology.

8. Turn on the power to the DisplayPort source. The OUTPUT (orange)

LED on the local transmitter unit will illuminate to indicate a signal is received from the source.

9. The RJ45 (orange) LED will illuminate on both local transmitter and

remote receiver units to indicate a signal is being received from source to display. The screen should now display on the connected monitor.9 Standard Extender Installation Notes:

• Test to ensure the entire installation works properly before pulling cables through ceilings/walls.

• To achieve maximum distance and performance, use 24 AWG solid-wire Cat6 cable. Using stranded-wire Cat6 cable, or cable with a gauge (AWG) size higher than 24 AWG will result in shorter extension distance. Higher gauge cabling, such as 26 AWG, has a more limited transmission capability than lower gauge cabling. All Tripp Lite N202-Series Cat6 cables use 24 AWG solid-wire cabling.

• The installation diagram shows the B127-004-D4H local transmitter unit. The B127-002-D2H installation is the same, except there are only two remote ports and no local monitor port. The B127-008-D Transmitter Unit features eight remote ports and one local monitor port.

1. Make sure all equipment in the installation—such as TVs, Blu-ray

players and the transmitter—is powered OFF.

2. Using DisplayPort cables (such as Tripp Lite P580-XXX-Series),

transmitter unit to the RJ45 port on the B127-100-H remote receiver unit.

5. Repeat step 4 for each additional remote receiver unit being

6. Using an HDMI 2.0 cable (such as Tripp Lite P569-XXX-CERT or

P568-XXX-2A-Series cable), connect the B127-100-H’s HDMI port to a monitor.

7. Repeat Step 6 for each additional remote B127-100-H receiver unit

in the installation.

8. Power on all connected displays. The LOCAL (orange) LED will

illuminate to indicate the local port is connected to a display.

9. Connect the external power supply to the B127-002-D2H,

B127-004-D4H or B127-008-D local transmitter unit and plug it into an available wall outlet or (optional) a Tripp Lite Surge Protector, Power Distribution Unit (PDU) or Uninterruptible Power Supply (UPS). The POWER (green) LED will illuminate to indicate the unit is receiving power from the external power supply. On the B127-100-H, the POWER (green) LED on the remote receiver unit will illuminate to indicate the unit is receiving power from the extender/splitter.11

10. Turn on the power to the DisplayPort source. The (orange) LED on the

B127-002-D2H, B127-004-D4H or B127-008-D will illuminate to indicate a signal is received from the source. Additionally, the OUTPUT (orange) LED will illuminate for each port signal connection.

11. The RJ45 (orange) LEDs on the B127-100-H will illuminate to

indicate a signal is being received from the extender/splitter. The screen should now display on the connected monitor. Standard Extender Installation Warranty and Product Registration 1-Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment, which has been damaged by accident, negligence or misapplication or has been altered or modified in any way. EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser. EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.12 Warranty and Product Registration PRODUCT REGISTRATION Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

• No purchase necessary. Void where prohibited. Some restrictions apply. See website for details. WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union) Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)

• Send the new equipment back for recycling when this ultimately becomes waste Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and illustrations may differ slightly from actual products. 1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support 20-02-117 93-393A_RevB13 Manual del Propietario Extensores y Divisores DisplayPort 4K / 60 sobre Cat6 Modelo de Juego de Extensor: B127-1A1-DH Modelos de Juego de Divisor: B127-002-D2H, B127-004-D4H Modelo de Transmisor Local: B127-008-D 1111 W. 35th Street, Chicago, IL 60609 EE UU • tripplite.com/supportCopyright © 2021 Tripp Lite. Todos los derechos reservados. English 1 • Français 26 • Русский 3914 Contenido del Empaque Características del Producto Todas