XBlast - Remote control toy Overmax - Free user manual and instructions

Product type	Radio-controlled toy (car)
Brand	Overmax
Model	XBlast
Car power supply	Lithium battery 7.4V (included)
Controller power supply	3 AA 1.5V batteries (not included)
Charging time	Approximately 150 minutes
Recommended charger	USB adapter 5V/1A (not included)
Recommended age	14 years and above
Main functions	Forward, brake/reverse, adjustable steering, variable acceleration
Remote control range	Not specified (estimated 20-30 meters)
Package contents	Car, controller, lithium battery, USB cable, 4 clips, 2 nuts, screwdriver
Car dimensions	Not specified (estimated 30 cm long)
Car weight	Not specified (estimated 500 g)
Cleaning	Damp cloth, no chemicals
Maintenance	Oil moving parts, remove battery if not in use
Safety	Do not use near water, do not charge unattended, avoid heat sources
Repairability	Contact an authorized service, do not modify

Frequently Asked Questions - XBlast Overmax

How to recharge the car battery?

Turn off the car, disconnect the battery, connect it to the USB cable, then plug the cable into a computer or 5V/1A adapter. The green light indicates charging. Allow approximately 150 minutes. Never leave the battery charging unattended.

Which batteries to use for the controller?

The controller requires 3 AA 1.5V batteries (not included). Follow the polarity indicated inside the compartment.

How to pair the controller with the car?

First turn the car ON, then turn the controller ON. Wait approximately 15 seconds for the connection to establish. The power LED should light up.

From what age can this toy be used?

This toy is recommended for children aged 14 years and above. Do not allow younger children to play without supervision.

What to do if the car does not drive straight?

Use the steering adjustment knob on the controller. Turn it to align the front wheels. Refer to figure 7 in the manual for details.

How to clean the car?

Turn off the device and remove the battery. Clean with a damp cloth (no chemicals). Remove sand and dust after each use. Keep all parts dry.

Can I use a different charger than the one provided?

You can use a USB adapter with the following specifications: 5V / 1A. Never use a higher power charger.

What to do if the controller blinks red?

The blinking red LED indicates low battery in the controller. Replace the three AA batteries with new ones.

Can I use the car on grass or sand?

It is best to use the car on flat, hard surfaces. Avoid sand, grass, or surfaces that may damage the vehicle.

How to adjust the maximum speed?

Turn the accelerator control on the controller: clockwise to increase speed, counterclockwise to decrease. Refer to figure 9 in the manual.

USER MANUAL XBlast Overmax

EN: The product complies with requirements of EU directives.

Pursuant to the Directive 2012/19/EU, this product is subject to selective collection. The product must not be disposed of along with domestic waste as it may pose a threat to the environment and human health. The worn-out product must be handed over to the electrics and electronics recycling center.

Thank you for placing trust in us and choosing Overmax.

Thanks to the use of high-quality materials and modern solutions, we provide you with a product perfect for everyday use. We are convinced that the product will satisfy your requirements as it has been manufactured with utmost care. Before you use the product, please read this manual carefully.

Should you have any remarks or questions concerning the product, please do not hesitate to contact us:

Please read this manual before you start using the product to see all its functions and use them in accordance with intended use.

1. Do not repair or modify the device. Only an authorized service technician is allowed to perform these operations.
2. Do not switch the device on if you have noticed any damage.
3. Do not use the device when it acts up, has been dropped or immersed in water, overheats extensively, is discolored or deformed, and when other atypical circumstances occur. Contact the manufacturer's authorized service center.
4. Never leave the charging battery unattended.
5. The device is intended for persons aged above 14. Do not let younger children play with it.
6. Use the device away from sources of heat, high temperatures, hot surfaces, direct sunlight, source of ignition, naked flame, oils and sharp edges.
7. Do not use the device in inflammable, explosive or toxic atmosphere.
8. Do not use chemicals to clean the device.

EN

1. After every use, switch the device off and disconnect the battery.

2. Do not immerse the entire device in water or other liquids. Do not use the device near water.

3. Before you start cleaning or moving the device, switch it off.

4. Do not use the device for other purposes than designed.
5. Keep the device away from sharp items.
6. Do not place other items on the device when you use it.
7. Use the device on flat and hard surfaces only. Avoid going on sand, grass or other surfaces which may lead to damage.
8. To charge a battery, use a supplied charging cable only.
9. After every charging, disconnect the charging cable from USB port.
10. Pay attention to battery polarization in the device and controller.
11. In the device use the supplied battery only, in the controller three batteries AA 1,5V are used (they are not supplied). In the controller do not use storage batteries.
12. After the use, do not touch a car engine because it may be extremely hot.
13. Transformer, power supply, or battery charger used with the electric device shall be regularly examined for damage to the supply cord, plug, enclosure or other parts, and in the event of such damage, it shall not be used until the damage has been repaired.
14. The device must not be connected to more power sources than recommended.
15. Recharge the batteries only under adult supervision.
16. Batteries must be removed from the device before charging.
17. Do not use different types of batteries or new and used batteries.
18. Remove exhausted batteries from the device.
19. Power terminals should not be short-circuited.
20. Non-rechargeable batteries should not be recharged.

1. Description of box content (see fig. 1):

1. Controller
2. Lithium battery 7.4V

3. USB charging cable

4. Car

5. 4 × Clasp, 2 × Nut
6. Screwdriver

The power adapter is not supplied. Use the power supply of the following parameters:

Input: 100-240V~50/60Hz, Max 0.2A

Output: 5V-1A

2. Description of controller (see fig. 2):

1.Forward
2. Brake/Reverse
3. Control knob
4. Wheel turn adjustment
5. Reversed direction of control knob operation
6. On/off switch
7. Reversed direction of throttling valve operation
8. Power/connection LED
9. Toe-in adjustment
10. Acceleration adjustment

1. On/off switch
2. Motor
3. Battery connector

3. How to charge battery (see fig. 10):

Charge the battery before use.

• Switch the car off.
• Disconnect the battery from the car before charging.
• Connect the battery plug to USB cable.
• Connect USB cable to PC or USB adapter.
• Charging takes about 150 minutes. A green light on the charger suggests the battery is connected.
• Disconnect the battery from charger and insert it in the car.

EN

NOTE After using in the car, wait 10-15 minutes before you start charging the battery. Do not leave the charging battery unattended. Recommended charger parameters: 5V mA.

4. How to assemble batteries in the controller (see fig. 4):

1. Loosen the screw of the battery cover with a screwdriver. Remove battery cover.
2. Insert 3 AA batteries 1.5V . Pay special attention to battery polarity.
3. Put the cover back on. Tighten the screw with a screwdriver.

A red flashing LED on the controller means the battery is low. Stop the car and replace all three batteries 1.5V AA.

5. How to pair controller with the car (see fig. 5):

• Slide the on/off switch on the car into „ON". Switch the on/off switch into „ON" to start the car.
• Slide the on/off switch on the controller into „ON". Power LED will go on.
  If the LED fails to go on, check the controller's batteries for suitable condition and proper assembly.
• Wait for about 15 seconds until the controller connects to the car.

6. How to control the vehicle (see fig. 6):

• Remove the protective film from the car before use.
• Turn the knob left or right to move front wheels.
• Press the controller's throttling valve to go forward. The farther you move the valve, the faster the car drives. Move the throttling valve forward to brake and then reverse.

7. Description of controller functions:

If you can see the car deviates to the left or right instead of going straight, you can adjust the turn with toe-in adjustment on the controller. Keep the front of the car in the air when using the adjustment (see fig. 7).
- To change the wheel turning angle, turn the wheels turning adjustment knob (1) to the right to increase the angle, or to the left (2) to reduce the angle. If you set the knob in „0" position, the car will not turn (see fig. 8).
- To adjust the speed, turn the throttling valve adjustment to the right (1) and the maximum speed will be increased. Turn it left (2) to reduce the maximum speed (see fig. 9).

8. How to clean and maintain

• Before you start cleaning, switch the device off and remove battery.
• Apply oil on all moving parts.
• Clean the car and controller with a wet cloth.
• Do not use chemicals to clean the device.
  After every use, remove sand and dust from the car. Make sure all elements of the car are always dry.
• Remove the battery from the controller when you do not use it.

The pictures are for reference only. The real design of products may differ from the pictures presented.

Einführung