WC126433 - Wine cellar Emerio - Free user manual and instructions

Product type	Wine cellar
Brand	Emerio
Model	WC126433
Capacity	Up to 105 bottles (Bordeaux type)
Temperature range	5 °C to 18 °C
Temperature zones	2 zones: upper (5–12 °C), lower (12–18 °C)
Climate class	N/ST (16–38 °C)
Refrigerant	R600a (28 g)
Power supply	220–240 V~, 50 Hz, 2.0 A
Electric shock protection	Class I
Insulation blowing agent	Cyclopentane
Number of shelves	4 adjustable metal shelves
Interior lighting	LED (switchable)
Ventilation	Internal fan for air circulation
Door reversal	Yes (right or left opening)
Defrost	Automatic (natural)
Recommended serving temperatures	Champagne: 6 °C, dry white wine: 10 °C, red wine: 16–18 °C
Display	Digital LED, adjustable in °C or °F
Reset function	Unplug for a few minutes to reset
Warranty	2 years from date of purchase

Frequently Asked Questions - WC126433 Emerio

What is the maximum bottle capacity?

The wine cellar can hold up to 105 bottles of Bordeaux type. Larger bottles reduce the capacity.

How to adjust the temperature?

Use the Up (K4) and Down (K5) buttons on the control panel. Press to make the display flash, then adjust. The temperature stabilizes after approximately 24 hours.

Can I change the door opening direction?

Yes, the door can open to the right or left. Follow the manual instructions to reverse the hinges. Two people are recommended.

What to do in case of a power failure?

Settings are preserved. Do not open the door to maintain temperature. In case of prolonged outage, unplug the appliance and store wine elsewhere.

How to clean the wine cellar?

Unplug the appliance. Remove shelves and wash them with warm water and mild detergent. Clean the interior with the same solution. Wipe the door gasket. Dust the rear condenser.

Why is my appliance making noise?

Gurgling or cracking noises are normal, caused by refrigerant circulation. Ensure the appliance is level. Normal noises are not covered by warranty.

The display shows an error code, what to do?

Codes E1 (internal temperature), E2 (ambient temperature), or CE (communication) indicate a problem. Unplug the appliance for a few minutes to reset. If the problem persists, contact customer service.

How long does it take to reach the set temperature?

It takes approximately 24 hours for the temperature to stabilize. Time may vary depending on load, ambient temperature, and door opening frequency.

Can I freeze food in this wine cellar?

No, this appliance is designed only for wine storage. It is not suitable for freezing food.

How to maintain the appliance during prolonged absence?

Unplug the appliance, empty it, clean the interior, and dry it. Leave the door slightly open to prevent mold.

USER MANUAL WC126433 Emerio

Exterior view of a black stainless steel refrigerator with clear glass doors and ventilation slots (no visible text or symbols)

Wine Cooler (EN)

Weinkühler (DE)

Instruction manual – English ...... - 2 -

Before use make sure to read all of the below instructions in order to avoid injury or damage, and to get the best results from the appliance. Make sure to keep this manual in a safe place. If you give or transfer this appliance to someone else make sure to also include this manual.

In case of damage caused by user failing to follow the instructions in this manual the warranty will be void. The manufacturer/importer accepts no liability for damages caused by failure to follow the manual, a negligent use or use not in accordance with the requirements of this manual.

1. Read and save these instructions. Attention: pictures in the instructions are for reference only.

2. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

3. Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances.

4. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

5. WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

6. WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

7. WARNING: Do not damage the refrigerant circuit.

8. WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

9. Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

10. This appliance is intended to be used in household and similar applications such as

11. staff kitchen areas in shops, offices and other working environments;

12. farm houses and by clients in hotels, motels and other residential type environments;
13. bed and breakfast type environments;

14. catering and similar non-retail applications.

15. WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.

16. WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.

17. To avoid contamination of food, please respect the following instructions:

18. Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.

19. Clean regularly surfaces and accessible drainage systems.
20. Clean water tanks if they have not been used for 48h; flush the water system connected to a water supply if water has not been drawn for 5 days. (Only applicable to water dispenser and water inlet system.)

21. If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould developing within the appliance.

22. This refrigerating appliance is not intended to be used as a built-in appliance.

23. Climate class:

- Extended temperate (SN): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 10°C to 32 °C';

• Temperate(N): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 32 °C';
• Subtropical (ST): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C';

• Tropical(T): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 43 °C'.

• This appliance is intended to be used exclusively for the storage of wine.

• This refrigerating appliance is not suitable for freezing foodstuffs.

• Do not use it outdoors. Keep it away from sources of heat, direct sunlight and humidity.

• Children should be supervised to ensure that they do not play with the appliance.

• It is recommended to check regularly the supply cord for any sign of possible deterioration, and the appliance should not be used if the cable is damaged.

• This appliance should not be used for commercial or industrial purposes or for any purpose other than the one for which it was designed. This appliance is intended for wine storage.

• Before inserting the plug into the mains socket, please check that the voltage and frequency comply with the specifications on the rating label.

• To remove the plug from the plug socket, pull the plug. Do not pull the power cord.

• Do not wind the cord around the appliance and do not bend it.

• Do not connect the device to a power outlet that is not protected from overloads.

• Never use power boards with multiple sockets to connect the device.

• WARNING: Do not immerse the cord in water, handle the electrical components or grip them with wet hands.

• The power socket to which the appliance is connected must be easily accessible, so it can be disconnected quickly in an emergency.

• Turn the appliance off before unplugging the power cord from the socket.

• This appliance is not intended to be activated by an external timer, by a separate remote-control system or any other device that automatically switches on the device.

• If you do not use the appliance for a long period of time, please turn it off and unplug it from the power supply.

• Do not store explosive materials such as aerosol containers with a flammable thruster in this device.

• Any maintenance or repair of this device must be carried out by a licensed professional. Do not attempt to repair the device yourself.

• WARNING: The ventilation openings on the appliance's casing must remain uncovered. Be careful not to block them.

• WARNING: Do not use mechanical devices inside the appliance.

• WARNING: Do not dismantle or otherwise damage the refrigeration system.

• This appliance is heavy. Be careful when moving it.

• When transporting the appliance, be careful not to damage any part of the refrigeration system.

• Important! Leave your device vertical for 24 hours before plugging it in for the first time so the refrigerant gas can equalize.

• If your device has been horizontal during transport, wait 48 hours before turning it on.

• After installation, make sure the appliance is not resting on the power cable.

• Never clean the appliance with flammable products. The fumes could cause a fire or explosion.

• WARNING: Do not use electrical devices to clean your appliance.

• Regarding the information pertaining to the installation, handling, use, servicing, replacement of lamp (if applicable), cleaning and disposal of the appliance, thanks to refer to the below paragraph of the manual.

WARNING: Risk of fire / flammable materials

The coolant circuit of this unit contains the refrigerant isobutane (R600a), a natural gas that is flammable and of high environmental compatibility. Make sure no parts of the coolant circuit get damaged during transport and installation of the appliance.

If the coolant circuit is damaged:

• avoid any open flames or ignition source;
• disconnect the plug;
• thoroughly air the room in which the appliance is installed and contact an authorized technician.

TRANSPORT AND PACKAGING

Transport the appliance

Transport the appliance, if possible, in vertical position. Otherwise, it is absolutely necessary to allow the appliance standing upright for 48 hours before installation. Protect the appliance during transport against weather influences.

Unpacking the appliance

• Remove the appliance from its packaging.
  • To prevent hazards, check the appliance for any transport damage.

NOTE: Production residue or dust may have collected on the appliance. We recommend cleaning the appliance according to chapter "Cleaning and Maintenance".

APPLIANCE EQUIPMENT

Appliance overview

1. Fan
2. Control panel & digital display
3. Glass door
4. Metal shelf with wooden trim
5. Temperature sensor
6. Adjustable foot

INSTALLATION

Conditions for the installation location

• Good ventilation is required around the appliance to dissipate the heat properly and to guarantee efficient cooling operation at low power consumption. Enough clearance is necessary.
  To ensure adequate ventilation of the appliance, allow a minimum of 15 cm between the appliance and the nearby walls as shown in the illustration below.

- Only install at a location with an ambient temperature suitable for the climate class of the appliance. The climate class can be found under "TECHNICAL SPECIFICATIONS".

- Place the appliance on a steady and safe surface. If the appliance is not horizontally leveled, adjust the feet accordingly.

- Avoid the installation:

- near heaters, next to a stove, direct sunlight or any other heat sources;

- at locations with high humidity (e.g., outdoors, bathroom), as metal parts would be susceptible to corrosion under such circumstances:

- near volatile or flammable materials (e.g., gas, fuel, alcohol, paint, etc.), in rooms which may have poor air circulation (e.g., garages).

- Do not expose the appliance to any weather.

- Some microwaves do not have a wave jamming shield so when your appliance is placed less than 1m from a microwave, the operation of your appliance can be affected.

• The appliance must be positioned so that the power socket remains accessible after installation.

• Unwind the power cord but do not plug it into the electricity supply immediately.

- Install your appliance in its final location before loading it. If the appliance is moved while loaded, the appliance's walls may be permanently deformed.

• IMPORTANT: Two people are required to properly and safely install the appliance.

Foot adjustment

Your appliance is equipped with adjustable feet to facilitate levelling.

It is recommended to adjust the front feet to level the appliance. Correctly levelled feet will limit noise and vibration of the appliance.

Turn the adjustable foot by hand (be careful not to jam your fingers).

- Turn the foot anti-clockwise to raise the level of the appliance.

- Turn the foot clockwise to lower the level of the appliance.

Before loading your appliance

• Levelling: The appliance must be levelled before loading your wine.

• Stable floor: Place the appliance on a stable surface where the ground can support the loaded weight.

Ambient temperature

The appliance should be placed in a room with temperature between 16-38°C. If the ambient temperature is above or below the climatic class, the performance of the appliance will be impacted. Cold or warm temperature can cause fluctuating fridge temperatures, the appliance may not reach the set temperature or may stop working.

Electrical connection

Warning:

• The installation to the mains supply must conform to the local standards and regulations.
• Improper connection may cause to an electric shock!
- Do not modify the appliance plug. If the plug does not fit properly to the outlet, let install a proper outlet by an authorized specialist.
- The accessibility of the power plug must be ensured to disconnect the appliance from the power supply in case of emergency.
• Make sure that the voltage supply matches the specifications on the rating label before connecting.
- Connect the mains cable to a properly installed and earthed wall outlet.
- If the plug after installation is not accessible, a corresponding disconnect device must be available to meet the relevant safety regulations.

Changing the orientation of the door

The door can be right or left opening. Change the door by following the instructions below. Making this change requires 2 people.

Instructions for changing the "right-hung" door and reassembling it so it is "left-hung":

(The pictures below are for the guideline to reverse the door. The appearance of the appliance may be different from the product you purchased.)

Note: The door seal may come out of its place when changing the door. If you notice gaps between the seal and the appliance frame when the door is closed, pull carefully on the seal to close these openings. The correct positioning of the seal is important to ensure the appliance is waterproof.

1. Unplug the power cord from the socket.2. Remove the top hinge cover.3. Unscrew the top hinge and remove it, then remove the door by gently lifting it.
4. Unwind the front right foot completely until it comes off. Remove it.5. Unscrew the lower hinge and remove it.
6. Place the lower hinge on the opposite side after removing the front foot and attach the hinge with the screws you have just removed from the right side.7. Replace the foot on the left side of the appliance with the adjustable foot removed from the right side. Screw the smaller foot onto the right side.
8. Place the door on the lower hinge. Make sure the glass door is upright and closes easily.
9. Place the top hinge on the opposite side.10. Place the door on the appliance, then loosely screw the hinge without tightening completely.
11 Once the door is installed, adjust the hinge by tightening the screws until the door is in the correct place.12. Replace the top hinge cover.

BEFORE USE

Prior to first use

Caution:

After transport, the appliance should be left standing upright for 24 hours before connecting to the power supply. Nonobservance could lead to malfunction of the cooling system and causes an appliance break-down.

Clean the appliance interior including all accessory parts. Consider the instructions which we provide in the chapter “Cleaning and Maintenance”.

Leave the appliance open to eliminate residual odors.

Recommendations:

• Place the appliance in a cool place away from sunlight and heat sources.
• Certain parameters such as room temperature, door opening time or the number of bottles stored inside could affect the internal temperature of your appliance. We recommend that you check the internal temperature regularly and adjust it if necessary.
• Do not cover the vents.

Operating noise:

To reach the desired temperature, this appliance, like all wine fridges with compressor cooling systems, can produce certain noises, which are normal operating noises.

• Gurgling noise: caused by the refrigerant gas circulating in the refrigeration area of the unit.
• Cracking noise: resulting from the contraction and expansion of the gas to produce the cold.

The perception of noise by the individual is directly related to the environment in which the appliance is located. Noise in normal operation is not a cause of the warranty's application.

USING YOUR APPLIANCE

1. Loading your appliance

• You can load your wine bottles in single or double rows.
• For loading, take note of the following: if you don't have enough bottles to completely fill your appliance, it's best to spread the load over the entire height of the appliance to avoid a thermal imbalance at the top or bottom of the appliance.
• The balanced distribution of bottles throughout the height of the appliance is the most efficient way to use the energy of the appliance.
• The bottle capacity is expressed in bottles of the “Bordeaux” type. If larger bottles are stored, or if additional shelves are used, the maximum bottle capacity is reduced.
• To accommodate the largest type of bottle or increase the capacity of the appliance by stacking the bottles, when necessary, the shelves must be removed or moved (see paragraph "Adjustable shelves").
• Keep a gap between the bottom of the appliance and the bottles to allow air to flow. As in an underground wine cellar, air circulation is important for a homogeneous temperature inside your wine fridge. This will also reduce energy consumption.

Important information about the serving temperature of wine

Your appliance has been designed to allow you to set desired serving temperature of your wine. Each wine varietal is served at a different ideal temperature.

The temperature is adjustable from 5-18 °C. Unless the wine producer recommends a different temperature for your particular wine, champagne should be served at 7°C, white wine should be served at 12°C and red wine should be served at 18°C (see table in “Wine service temperatures”).

Some wines can be served young (2 to 3 years), while others are much better aged (10 years and older). Each wine peaks at a different age. Check the ideal drinking age for your wine with your wine merchant.

Setting types: Please note that depending on where your appliance is kept, how often the door is open, the ambient temperate and the loading, the time taken to reach the set temperate varies. Usually, it takes about 24 hours for the appliance to reach the desired temperature and indicate a stable temperature on the digital display. The temperature displayed will change when the desired temperature is adjusted or whenever a large number of bottles are added to the appliance.

2. Loading plan

• Your appliance can accommodate up to 105 bottles, of light Bordeaux type, with a stack based on three shelves.
• While loading several levels of bottles on the same shelf, please gently store your bottles in the 1st row to prevent them from colliding with the 2nd row. Store the bottles in a "head to tail" - crossing the neck and bottom of each bottle, so you can get close to the stated maximum capacity.
• If you store larger bottles or add a shelf to more easily access of your bottles, storage capacity will be reduced.
• The way you load your appliance and the number of shelves, determines capacity. Below you will find an explanatory diagram for loading (capacity with load "head to tail"):

Diagram of a multi-tiered cylindrical container with circular holes, no text or symbols present

Diagram of a multi-tiered cylindrical structure with concentric circles, no text or symbols present

Pure schematic diagram of five identical mechanical or fluidic components with no text, numbers, or symbols

• The indoor fan helps keep the temperature consistent throughout the appliance. The appliance door should not be kept open for long periods of time as it will impact the appliance's ability to remain cool.

• This appliance is a multi-zone fridge which allows you to set the temperature of each compartment independently. As wine is best served at different temperatures depending on the type of wine, you can store multiple types of wine in your appliance at their ideal temperatures following the temperature settings below:

• Top compartment of the unit (5-12°C): rosé wines, champagne and white wines

• Bottom compartment of the unit (from 12-18°C): red wines

3. Adjustable shelves

• Your appliance has 4 adjustable metal shelves, which gives the strength to stack several rows of bottles (the moulding at the bottom of the appliance allows bottles to be stacked underneath the bottom shelf).
• The shelves can be adjusted to different spacings depending on your needs (be careful not to place bottles on the temperature zone separator).

• Door seal protection: Ensure you open the door completely before removing shelves from their rails.
- Do not slide multiple loaded shelves outwards as it may cause bottles to fall or may cause the appliance to tip forward.
- Do not cover shelves with material like aluminum foil or metal plate as this will impact internal airflow.
- Do not move your appliance while it is loaded with bottles. This could distort the walls of the appliance and cause back injuries.

4. Functions and temperature setting

Please note that depending on the selected settings and the loading, it can take 24 hours for the appliance to reach the desired temperature.

• Plug the power cord into a suitable power supply.
• Set the thermostat to adjust the temperature using the K4 and K5 keys

K1: On/Off

Press the key to start or turn off the appliance.

K2: Light

Press the key to turn on / off the inside light.

K3: Select the storage area

Press this key to select the top or bottom zone.

L1: View temperature by selected area

Temperature display:

A: Top zone: 5-12 °C

B: Bottom zone: 12-18 °C

Note: Symbol “%” in the lower right corner means humidity. It is not applicable to this product/model you purchased.

K4: Increase temperature

Press the key once, the LED display will flash indicating the current temperature. Press again to set the temperature. One touch will increase the temperature by one degree. The blink stops after 5 seconds without action on your part, and the newly set temperature is recorded. The LED display then shows the actual temperature inside.

K5: Decrease temperature

Press the key once, the LED display will flash indicating the current temperature. Press again to set the temperature. One touch will reduce the temperature by one degree. The blink stops after 5 seconds without action on your part, and the newly set temperature is recorded. The LED display then shows the actual temperature inside.

K6: Settings

Fahrenheit/Celsius

Switch the temperature display between Fahrenheit/Celsius by pressing the key.

There are two internal fans for airflow however fluctuations of up to 3 degrees is expected. The average temperature throughout the appliance will be a maximum of 1.5^ C of the requested temperature (once sufficient time for cooling has passed). Once a temperature difference of 3^ C above the set temperature is detected, the cooling cycle will start to bring the temperature down to below the set temperature. Once the cooler temperature is reached, the cooling stops and the temperature inside the appliance is allowed to slowly increase. This cycle is continuous and results in a very small range of constant fluctuation.

The temperature sensor is placed halfway down the compartment and reads the temperature instantaneously. Small amounts of deviation in temperature are expected (less than 6^ C).

Please do not open the door too often as this will disrupt the operation of the temperature sensors. The appliance automatically adjusts moisture and condensation levels within the appliance as required.

Attention

When the temperature sensor is failing due to power outage or bug, an error code appears.

E1: internal temperature problem

E2: ambient temperature problem

CE: communication problem

5. Wine service temperatures

The table below shows the recommended serving temperatures for different wine.

Wine	Recommended temperature
Champagne, sparkling	6 °C
White: Sémillon, Sauvignon Blanc	8 °C
Vintage Champagne	10 °C
Dry white: Chardonnay	10 °C
Dry white: Gewürztraminer, Riesling, Pinot gris	10 °C
Sweet late harvested white: Sauternes, Barsac, Monbazillac	10 °C
Beaujolais	13 °C
Sweet white wine: Sauternes...	14 °C
White Chardonnay vintage	14 °C
Pinot Noir Red	16 °C
Red Grenache, Syrah	16 °C
Red vintage Pinot Noir	18 °C

To bring the wine to the serving temperature, it is recommended to place it in your appliance at least 48 hours before serving and uncork or aerate a few minutes before tasting.

6. Power outage

In the event of a power outage, all temperature settings will be automatically preserved, unless you change the thermostat setting.

A power outage of an hour or two will not affect the temperature of your appliance. To avoid a sudden change in temperature when the power supply is turned off, you should avoid opening the door. In the event of a prolonged cut, storage alternatives must be found to preserve your wine.

If you plan to temporarily shut off the electrical power or if there is a power outage scheduled by your power provider, it is imperative to disconnect the power socket rather than have your power meter shut down. A sudden shutdown of the current could damage the mother board in your appliance.

CLEANING AND MAINTENANCE

Defrosting

Your appliance is designed with a "natural" defrosting system. When the engine is shut down, the refrigerated surfaces of the appliance will automatically defrost. The de-icing water descends into a drainage container near the compressor at the back of the appliance. This water is evaporated by the heat produced by the compressor.

Important: Keep the drain and gutter clean to prevent it to clog and water to flow inside the appliance.

Cleaning

Before cleaning or restarting, unplug at the socket.

Never use abrasive products or sponges with scrapers for cleaning inside or outside your device.

- Remove all accessories (e.g., shelves, water pan located at the bottom of the back of the appliance). Wash them with lukewarm water with a mild, odorless detergent (an unscented dish liquid, for example), rinse with water containing bleach and dry thoroughly.

- Wash the interior walls in the same way; take special care of the shelves.

- Wash the door seal without omitting to clean also under the door seal.

- Reconnect the device and get it back into operation.

Occasionally, dust the condenser at the back of the unit; a build-up of dust could reduce the performance of the unit.

At certain times of the year, condensation on the door may occur. If this happens, wipe the water from the door and avoid opening the door of the appliance often as this amplifies the difference between the inside of the appliance and the ambient temperature.

In case of prolonged absence, empty and clean the appliance; keep the door ajar for the duration of non-use.

Important!

When the appliance is not used:

• Unplug the appliance.
• Remove all objects inside.
• Clean and dry the interior space of the appliance per the above instructions.
• Leave the door slightly ajar to avoid mold.

TROUBLESHOOTING

Some issues can be easily resolved. Before using after-sales service or a repairman, please see the following table:

Problem	POSSIBLE CAUSES
The appliance doesn't work.	The appliance is not plugged in or it is switched off.The circuit breaker is triggered, or the fuse is damaged.Check to see if the power outlet is powered by connecting another electrical appliance.
The appliance is not cold enough.	Check the temperature setting.A high ambient temperature may require a higher setting.The door is opened too often.The door is not completely closed.The door seal is not properly positioned.
The compressor works and goes out often.	The room temperature is warmer than normal.A large quantity of bottles has been added to the appliance.The door is opened too often.The door is not completely closed.Temperature control is not properly defined.The door seal is not properly positioned.
The light doesn't work.	The socket is not plugged in.The circuit breaker has gone off or a fuse is damaged.
Vibration.	The appliance may not be level.
The appliance seems to be making too much noise.	Squeaking or slamming may come from the circulation of the refrigerant gas, which is normal.At the end of the cycle, the compressor emits a noise caused by the passage of the refrigerant into your appliance.The contraction and expansion of the gas inside the walls can emit hissing and crackling.The appliance is not level. Check the setting of the feet.
The door doesn't close properly.	The door was reversed and not properly reinstalled.The seal is defective (the magnet or rubber is altered).The shelves block the door closure.

If your appliance doesn't seem to be working normally, unplug the device for a few minutes, then plug it in again to reset the appliance.

If the problem persists or for any other problems occurring at your device: contact the After-Sale Service.

Any service or repair on the cooling process must be carried out by a licensed professional who will have to carry out an inspection of the refrigeration circuit.

Similarly, any service or repairs on the electrical circuit must be carried out by a qualified electrician.

Note: Any repair by an unlicensed technician will result in cancellation of the warranty.

TECHNICAL SPECIFICATIONS

Rated voltage:	220-240V~
Rated current:	2.0A
Rated frequency:	50Hz
Climate class:	N/ST
Refrigerant:	R600a (28g)
Protection against electrical shock:	I
Insulation blowing gas:	CYCLOPENTANE

Climate class:

• Extended temperate (SN): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 10°C to 32°C';
• Temperate(N): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 32 °C';
• Subtropical (ST): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C';
• Tropical(T): 'this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 43 °C';

Note: More data information, please scan the QR code on the energy label.

GUARANTEE AND CUSTOMER SERVICE

Before delivery our devices are subjected to rigorous quality control. If, despite all care, damage has occurred during production or transportation, please return the device to your dealer. In addition to statutory legal rights, the purchaser has an option to claim under the terms of the following guarantee:

For the purchased device we provide 2 years guarantee, commencing from the day of sale. If you have a defective product, you can directly go back to the point of purchase.

Defects which arise due to improper handling of the device and malfunctions due to interventions and repairs by third parties or the fitting of non-original parts are not covered by this guarantee. Always keep your receipt, without the receipt you can't claim any form of warranty. Damage caused by not following the instruction manual, will lead to a void of warranty, if this results in consequential damages then we will not be liable. Neither can we hold responsible for material damage or personal injury caused by improper use or if the instruction manual are not properly executed. Damage to accessories does not mean free replacement of the whole appliance. In such case please contact our service department. Broken glass or breakage of plastic parts is always subject to a charge. Defects to consumables or parts subjected to wearing, as well as cleaning, maintenance or the replacement of said parts are not covered by the warranty and are to be paid.

The guarantee period of the spare parts is 2 years. If you need replacement, please contact our customer service.

ENVIRONMENT FRIENDLY DISPOSAL

Recycling – European Directive 2012/19/EU

This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used

device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

For professional repair and ordering spare parts, please contact our customer service.

Emerio B.V.

Zomervaart 1A

2033 DA Haarlem

The Netherlands

Service Hot Line: [phone]

Diagram of a multi-tiered storage unit with circular components, no text or symbols present

Diagram of stacked cylindrical objects in a container (no text or symbols)

Pure schematic diagram of five identical mechanical or electrical components with no text, numbers, or symbols

Diagram of a multi-tiered storage unit with circular components, no text or symbols present

Diagram of stacked circular components in a container-like structure (no text or symbols)

Pure schematic diagram of five identical mechanical or electrical components with no text, numbers, or symbols

PLACERING AV APPARATEN

Diagram of a multi-tiered storage unit with circular compartments and vertical supports (no text or symbols)

Diagram of a multi-tiered cylindrical structure with concentric circles and a base plate (no text or symbols)

Pure mechanical component diagram without any text, numbers, or symbols

3. Justerbara hyllor

BESCHRIJVING VAN HET APPARAAT

Diagram of a multi-tiered storage unit with circular compartments (no text or symbols)

Diagram of a multi-tiered cylindrical structure with circular holes, no text or symbols present

Pure schematic diagram of five identical mechanical or fluidic components with no text, numbers, or symbols

Diagram of a multi-tiered storage unit with circular and rectangular units, no text or symbols present

Diagram of stacked circular components in a vertical container (no text or symbols)

Pure schematic diagram of five identical mechanical or fluidic components with no text, numbers, or symbols

3. Regulowane półki