GF 384 - Milling machine Güde - Free user manual and instructions

Product type	Tiller (garden cultivator)
Brand	Güde
Model	GF 384
Engine type	4-stroke OHV
Maximum power	2.8 kW / 3.8 HP
Displacement	161 cm³
Maximum working width	360 mm
Number of blades	4
Sound power level	LWA 93 dB
Weight	31.7 kg
Blade brake	Blades stop within 3 seconds after releasing the lever
Safety gear	Gloves, goggles, ear protection, safety shoes
Warranty	24 months for the end consumer (12 months for professional use)
Order number	94392
Intended use	Gardening, agriculture, forestry
Maintenance	Oil change every 25 hours, air filter cleaning, spark plug check every 100 hours
Transport	Wheel in transport position, device switched off, drain fuel for long duration

Frequently Asked Questions - GF 384 Güde

What type of fuel to use for the Güde GF 384?

Use fresh unleaded gasoline. Do not use an oil-gasoline mixture as the engine is a 4-stroke with a separate oil sump. Follow the instructions in the manual for refueling.

What engine oil is recommended?

Use a 4-stroke oil of quality SAE 30 or 10W-40. Fill to the dipstick mark. The first oil change must be carried out after 25 hours of operation.

How to start the engine?

Set the lever to Starter, pull the starter cord evenly 3 to 5 times. Once started, set the lever to the desired speed. For a warm engine, start directly without choke.

What to do if the engine does not start?

Check the fuel level, clean the air filter, inspect the spark plug. If the engine is flooded, unscrew the spark plug, clean and dry it, then pull the cord several times without the plug.

How to adjust the working depth?

Move the depth limiter to one of the 3 available positions. Adjustment must be done with the engine off. The wheel must be in work position (position 12.1) for tilling.

What are the essential safety instructions?

Always wear gloves, goggles, ear protection and safety shoes. Never put your hands near rotating blades. Do not use the device in rain or in an enclosed space. Wait until the blades have completely stopped before touching the device.

How to transport the tiller?

Place the wheel in transport position (12.2). Make sure the engine is off. Drain the fuel if transport is long. Secure the device to prevent tipping or leaking.

How often should the oil be changed?

Oil change is recommended every 25 hours of operation. Check the oil level before each use and top up if necessary.

What to do in case of excessive vibrations?

Stop the engine immediately and check the tightness of all fastening screws. If the problem persists, have the device checked by an authorized workshop.

Where to find spare parts or after-sales service?

Visit the website www.guide.com in the Service section. For any complaint, have the serial number, order number (94392) and year of manufacture ready. Contact support by phone at +49 (0) 79 04 / 700-360 or by email at [e-mail].c

USER MANUAL GF 384 Güde

To enjoy your new GARDEN CUTTER as long as possible, please read carefully the Operating Instructions and the attached safety instructions before putting the appliance into operation. We also recommend keeping the Operating Instructions for future reference.

We reserve making technical changes to improve the appliance as part of the continuous product development.

This document represents the original Operating Instructions.

Any reprints, even partial, are subject to approval.

Scope of delivery (1)

1. Truck
2. handle (drive lever)
3. Drive lever
4. Depth limiter
5. Semibeam
6. Rotary wheel
7. handle (ON/OFF, speed)
8. Cross brace

Warranty

A warranty period of 12 months applies to commercial use and 24 months apply to private use and commences on the day of purchase of the device.

Warranty applies exclusively to failures due to defective material or workmanship. An original sale slip with indication of date of sale must be presented in case of claiming for the warranty rights.

Warranty does not cover unprofessional use such as device overload, violent use, damage caused by third party or foreign materials, failure to comply with operations and assembly manual, and normal wear and tear.

General safety instructions

It is necessary to read the whole guide for operation before the first use of the machine. In case of any doubts associated to the connection and operation of the machine contact the producer (service department).

TO MAINTAIN THE HIGH LEVEL OF SAFETY PLEASE OBSERVE THE FOLLOWING INSTRUCTIONS STRICTLY:

ATTENTION!

1. Pay attention to environmental conditions that you work in. The engine driven machine starts producing toxic gases after engine activation. These gases could be invisible and without any smell. Therefore you must never work with the machine in closed or badly ventilated areas. Provide good illumination for your work. If you cut in wet conditions, on snow or ice, in slopes or in unlevelled terrain, ensure good stability.
2. Do not let foreign persons accessing to the machine. Keep visitors and by-standers, especially children, sick or weak persons, in a safe distance from your workplace. Pay attention that other persons may not touch the machine.
3. Ensure safe storage of tools. Machine that are not in use store in a dry place at certain height if possible or lock them so that they are not accessible to other persons.

4. Use a proper tool for every work. Do not use e.g. small machines or accessories for works that should in fact be performed using heavy machines. Use machines exclusively for purposes which they were designed for.

5. Care for suitable wear. Your clothing should be purposeful and in may not constrain you in work.

6. Wear personal protective means. Wear safety shoes with steel puffs and non-skid sole.
7. Wear protective glasses. Shooting up of objects by the machine could occur.
8. Wear means for hearing protection. Wear personal means for hearing protection like ear obturators.
9. Hand protection. Wear solid gloves - good protection is provided by gloves made of chrome leather.
10. Transport. The garden cutter must be transported always with the rotary wheel in transport position. When machine is stand off pay attention that nobody could be threatened. Secure the machine against tipping over, damage and fuel leakage.
11. Remove wrenches etc. All wrenches etc. should be removed before the machine is started.
12. Stay always attentive. Pay attention to what you do. Follow your common sense when working. Do not operate engine-driven machines when tired. Do not operate the engine being under influence of alcohol, drugs or medicaments that aggravate the ability to concentrate.
13. Refilling the fuel. Before refuelling it is always necessary to stop the engine. Open the tank cover always carefully to allow the over-pressure ventilate slowly to avoid squirting the fuel. When working with the machine high temperatures are generated at the machine body so let the machine cooled down before refuelling otherwise fuel ignition could occur resulting in serious burns. Be careful not to overfill the tank when refuelling. If the fuel flows out nearby it must be removed immediately and the machine must be cleaned. Check firm settlement of screw cover after refuelling to avoid its loosening due to vibrations during operation.

Behaviour in case of emergency

Provide necessary first aid treatment corresponding to the injury nature and seek qualified medical help as soon as possible. Protect the injured person from other injuries and calm him/her down.

First aid kit must always be available in the place of your work in case of accident in accordance with DIN 13164. Material taken out of the first aid kit needs to be supplemented right away.

If help is needed, please provide the following details:

1. Place of accident
2. Accident nature
3. Number of injured persons
4. Injury type

Marking on the machine

Explanation of symbols

The following symbols are used in this guide and/or on the machine:

Safety of the product:

CE
The product corresponds to relevant standards of the EU

Restrictions:

Ban, general (in connection with other pictogram)	Fire, non-protected source of light and smoking forbidden
Do not finger into rotating parts	Do not use the machine when raining

Caution:

Caution/Attention	Warning from dangerous electrical voltage
Warning from inflammable substances	Caution-danger of tumbling over
Warning from hot surface	Warning from gases harmful for health
The machine may be used only outside closed rooms	Warning from rotating parts
Warning from objects flying away	Keep the safety distance

Orders:

Wear ear-phones

Wear protective shoes

Read the guide for operation before use

Environmental protection:

Waste should be disposed by expert service so that to avoid any environmental damage.

The packaging material from the cardboard can be handed in into a collection point for recycling.

Packaging:

Protect from moisture	The package must point upwards	Attention - Fragile
Interseroh-Recycling

Technical specifications:

Engine output

Working width

Engine speed

Tank volume	Weight	Capacity
LWA dB
Noise

Use in accordance with designation

The machine is designed only for ordinary use in agriculture, forestry, gardening and care for greenery. When provisions given by general regulations and/or by this guide the producer cannot be held responsible for any damage.

Residual risks and preventive measures

Mechanical residual risks

Threat	Description	Protective measure(s)
Cutting, cutting off	Rotating plough-blades could cause serious cutting injuries and possibly amputation of bodily parts.	Always wear protective gloves. Never finger into the machine when operated.
Catching, winding up	Weeding plough-blades could wind ropes, wires or parts of clothing up to them.	Remove alien objects from the land, keep distance from fencing, wear close-fitting clothing.

Electrical residual risks

Threat	Description	Protective measure(s)
Direct contact with electricity	Touching the spark plug extension when the engine is running could result in electrical accident.	Do not touch the spark plug extension when the engine is running.

Thermal residual risks

Threat	Description	Protective measure(s)
Burns, frost-bites	Touching the exhaust pipe could cause burns.	Let the machine to be cooled down.

Danger from noise

Threat	Description	Protective measure(s)
Hearing impairment	Frequent and/or long-term work with the machine without ear protectors could cause a hearing impairment.	Wear ear protectors.

Danger from vibrations

Threat	Description	Protective measure(s)
Whole body vibrations	Prolonged work with the machine could result in bodily harms due to vibrations.	Make breaks from work regularly.

Danger from materials and other substances

Threat	Description	Protective measure(s)
Contact, aspiration	Inhalation of exhausting gases could be extremely harmful for health.	The machine may be operated outdoor only.
Fire or explosion	The machine is driven with inflammable mixture of fuel that could ignite for example during refuelling.	Do not refuel close to open flames and do not smoke during refuelling.

Other risks

Threat	Description	Protective measure(s)
Objects thrown away or splashing liquids	Stones or soil thrown away could cause injuries.	Make sure that no other persons are present in the work area and wear personal protective means.

Disposal

Instructions for waste disposal implying from pictograms that are located on the machine or possibly on the packaging. The explanation of such signs can be found in chapter "Marking on the machine".

Requirements for operators

The operator must read the guide for operation carefully before any use the machine.

Qualification

No special qualification except detailed instruction session led by an expert is necessary for use of the machine.

Minimum age

The machine may be operated by persons older than 16 years only. The exception is the case of the machine utilisation by operation by juvenile persons when this occurs used during profession training to get skills under supervision of a trainer.

Training

The operation of the machine requires just corresponding instruction by an expert or the guide for operation. No special training is necessary.

Technical specifications

Engine design:	4-Takt OHV
Max. output:	2,8 kW/ 3,8 PS
Swept volume:	161 cm³
Operating width:	360 mm
Number of plough-:	4
Noise:	LWA 93 dB
Weight approx.:	31,7 kg
Order No.:	94392

Transport and storage

• The machine may be transported with stopped engine only.
  Clean the machine thoroughly before storage.
• Store the machine at a clean and dry place.

Fuel or oil could leak out during transport of the machine. Please secure the machine in a corresponding way and make preventive protective precautions to avoid environmental pollution.

Assembly and putting into operation for the first time (Abb.1-9)

• Impeller (Fig. 1, 6) on the front of the device by means of nut and screw, (Fig. 2). Thereafter, the spring in the fender mount (Fig. 3).
• Depth limiter from the bottom to insert into the hole, secure with a cut-out with a pin.

• Handle bracket (Fig. 1, 5) with 4 screws behind the engine mount (Fig. 5+6)
  Cross brace assembly (Fig. 7)

• The PVC connection between the two handles plug and tighten the screw on the grip panel.
  Both handles to grip panel screw (Fig. 8)

• Mount throttle (Fig. 9)

Engine:

First filling oil into the oil filling (Fig. 10, A) is an up to the mark (Fig. 11).
Then, fill petrol in the tank (Fig.10, B).

Safety instructions for putting into operation for the first time

Always pay attention to tightening of bolting and use exclusively parts listed in the scope of delivery.

Procedure

Perform the assembly of individual parts in the illustrated order. Doing so pay attention to proper arrangement of construction parts according to illustrations.

The machine is delivered without oil and fuel due to transportation. Fill these according to the data.

Operation

Rotary wheel in operating position (Fig. 12)

Set the rotary wheel into the position 1 for cultivation. (Fig. 12,1)

ATTENTION!

The machine may be transported only with the rotary wheel in the position 2. (Fig. 12,2)

The rotary wheel may be adjusted only when the engine is stopped!

Cutting height calibration (Fig. 13)

Required depth of cultivation is set by shifting the depth limiter. Three different positions are possible.

Operating lever (Fig.14)

Starting/stopping the machine

Switch the handle to the Choke (Fig. 14). Now pull the starting string uniformly. The engine should start after 3 to 5 pulling the starting string. Put the handle (Fig. 14) onto the required speed and after that press the drive handle against the pillaret (Fig. 15)

Caution: If the engine has been warmed yet it can be started immediately into the position Slowly or Quickly.

After releasing the drive handle the drive stops but the engine keeps running. The engine can be stopped only by switching the switch into the OFF position (Fig. 14).

When starting the engine the machine must not tilt, only if necessary for the operator to start the engine at reverse side.

Safety instructions for the operator

• Use the machine only after having the guide for operation carefully.
• Observe all safety instructions specified in the guide.
• Act responsibly towards other persons.
• This machine is equipped with a brake of plough-blades to ensure that plough-blades stop after release of drive handle not later than in 3 seconds. Do not try to stop plough-blades or tilt the machine with rotating plough-blades aside under any circumstances. Wait until the plough-blades stop automatically.
  If plough-blades contact with a foreign object please stop the engine immediately and check the machine for damage when plough-blades stopped. Continue working only with undamaged machine.
• Walk only when working, no not run.
  Always walk forward when working. Never go back with the machine.
• On slopes work always across them and never up and down. Be especially careful when changing the direction.
• When crossing areas without grass and transportation to the workplace and back the plough-blades must not be in operation.

Step-by-step guide

1. Fill the fuel into the machine (chapter Assembly and 1putting into operation for the first time)
2. Remove any foreign objects from the terrain.
3. Cultivate the terrain with garden cutter until the soil is sufficiently cultivated.
4. Clean the machine thoroughly after each use.

Inspections and maintenance

Safety instructions for inspections and maintenance

Only regularly maintained and treated machine can become a satisfactory instrument. Insufficient maintenance and care could lead to unforeseen accidents and injuries.

• Always stop the engine and disconnect the spark plug extension in case of any work on the machine!
• Never use aggressive cleaning agents for cleaning. It could damage or destroy the machine.

Inspection and maintenance plan

Before start of work:

• Check the state of engine oil (Fig.10A+11)
• Check for loosen parts

Every 25 hours of operation

Engine oil replacement
Engine oil condition check
Air filter cleaning (Fig.16)
- Removing of remainders of grass or soil from rotating parts with a brush or an unpointed object.
- Wiping of the cover with a soft cloth. If a dirt is stiffened the machine may be cleaned using a soft cloth soaked with soapsuds.

Every 100 hours of operation

• Inspection, cleaning and possible spark plug replacement.(Fig.17)

Maintenance

Do you have any technical questions? A claim? Do you need spare parts or the Operating Instructions?

You will be helped quickly and without needless bureaucracy at our webpage www.guide.com in the Services part. Please help us be able to assist you. To be able to identify your appliance when claimed, we need to know its serial No., order No. and year of production. All these details can be found on the type label. Enter the details below for future reference.

Serial No.

Order No.

Year of production:

Tel.: [phone] / 700-360

Fax: [phone]

E-Mail: [e-mail]

Faults - Causes - Elimination

Fault	Cause	Elimination
Engine does not start	1. Empty tank2. Dirty air filter3. Weak ignition spark4. „Over-swilled“ engine	1. Fill the tank up to its full capacity; check whether the carburettor contains a fuel; check tank de- aeration and make an opening in the tank lid with a needle.2. Clean the air filter.3. Clean the spark plug or install the new one if necessary; check the ignition cable; let the ignition checked in a service.4. Unscrew the spark plug, clean it and dry; pull several times the starting string when the spark plug is unscrewed.
Engine outages occur	1. Ignition cable is loosened.2. Fuel piping is clogged or fuel is bad.3. Ventilation opening in the fuel tank lid is blocked4. There is water or dirt in fuel piping.5. Air filter is dirty.	1. Fit the spark plug extension firmly onto the spark plug.2. Clean fuel piping, use fresh fuel.3. Replace the fuel tank lid.4. Drain the fuel and refill clean and fresh fuel.5. Clean the air filter.
Engine often stop at idle run	1. Ignition distance is too long, spark plug is defective.2. Carburettor is not adjusted precisely.3. Dirty air filter	1. Adjust or replace the spark plug.2. Adjust the carburettor.3. Clean the air filter.
Drive does not work properly	1. Check the drive handle string tension.2. Drive does not work.	1. Perform additional adjustment of drive handle string tension if necessary. (pic. 19)2. Let the machine checked in a service point.
Excessive vibrations	1. Fixing screws are loosened	1. Tighten the fixing screws.

Introduction

Manuale step by step

Interseroh-Recycling

Muszaki adatok:

Translation of the EC-Declaration of Conformity

We, hereby declare the conception and construction of the below mentioned appliances correspond - at the type of construction being launched - to appropriate basic safety and hygienic requirements of EC Directives. In case of any change to the appliance not discussed with us the Declaration expires.

Annex IV Notified Body Name: No: Adress:

Type Ex.Cert.-No.:

2016/1628/EU

Emission No.: e242016/16282018/9895RA1/P025700

2000/14/EC_2005/88/EC