PSSFS 3 A1 - Socket tester PARKSIDE - Free user manual and instructions

USER MANUAL PSSFS 3 A1 PARKSIDE

Operation and safety notes

FR BE

TESTEUR DE PRISE

GB/IE Operation and safety notes Page 28

Warnings and symbols used ...... Page 29

Introduction Page 32

Intended use.... Page 32

Scope of delivery.... Page 34

Parts description.... Page 34

Technical data Page 35

Safety instructions.... Page 36

Before use.... Page 41

Use Page 42

Testing the socket wiring. Page 42

RCD test Page 43

Cleaning and care Page 45

Storage Page 45

Disposal Page 46

Warranty Page 47

28 GB/IE

Warnings and symbols usedThe following warnings are used in this user manual and on the packaging:
	DANGER! This symbol in combination with the signal word “Danger” marks a high-risk hazard that if not prevented could result in death or serious injury.
	WARNING! This symbol in combination with the signal word “Warning” marks a medium-risk hazard that if not prevented could result in death or serious injury.
	CAUTION! This symbol in combination with the signal word “Caution” marks a low-risk hazard that if not prevented could result in minor or moderate injury.
	ATTENTION! This symbol with the signal word “Attention” indicates a possible property damage.
	NOTE: This symbol in combination with “Note” provides additional useful information.
	Danger of explosion!
	Wear protective gloves!
	Conforms to European Union Directives.
	Read the instruction manual.

30 GB/IE

	Continuous double or reinforced insulation of category II DIN EN 61140
	Earth (Ground) Terminal
	Use the product in dry indoor spaces only.
	Alternating current (AC)
	Direct current (DC)

SOCKET TESTER

Introduction

We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

Intended use

This product is intended for checking the correct connection of 3-wire shockproof sockets and for indicating wiring errors by means of 3 LED indicators.

32 GB/IE

An inversion of the neutral and the earth conductors will not be detected by this product.

This product is integrated with an RCD (Residual Current Device) test function, which can be used to check the tripping function of a 30 mA RCD. It features rapid detection of correct/incorrect wiring, fast and effective RCD test function.

Any other use or product modification shall be considered improper use and holds considerable safety hazards. The manufacturer assumes no liability for damages due to improper use. Not intended for commercial use. This product is designed only for indoor use. Always observe the regulations and laws in the country of use.

- Scope of delivery

1xSockettester

1 x Instruction manual

Parts description

1 LED indicator: N (Neutral)
2 LED indicator: PE (Protective Earth)
3 LED indicator: L (Live)
4 Coding table
5 Button: RCD TEST
6 LED indicator: I n > 30 mA (RCD test)

Technical data

Nominal voltage: 220-240 V

\~, 50 Hz

Nominal current: < 3 mA

RCD test current: 30 mA

Size: Model HG05551C: 60 mm x 60 mm x 63 mm

Weight: Model HG05551C: approx. 72.2 g

Operation

Temperature: 0 to +40 °C

Relative humidity: < 80 %

The technical data and design may be changed without any notification.

Safety instructions

Before using the product, please familiarise yourself with all the operating and safety instructions. Please include all documentation when passing this product on to others.

The warranty will be void in the event of damage caused by failure to observe these safety instructions! We do not assume any liability for any resulting damage!

We shall not accept liability for damage to property or personal injury caused by incorrect handling or non-compliance with the safety instructions! In such cases, the warranty will be null and void.

The unauthorised conversion and/or modification of the product is not allowed for safety and approval reasons. Do not disassemble the product.

The product is not a toy. Be especially careful when children are around.

36 GB/IE

The product may not be used for verification of voltage absence. The absence of voltage may only be verified by a bipolar voltage tester according to EN 61243-3.
The audio signal heard, when voltage is checked, provides no reliable indications as to type and level of the voltage.
■ Only touch the product by the handle areas provided for that purpose. Do not cover the LED indicators.
Take particular care when dealing with voltages exceeding 30 V\~ or 30 V ---! Even at these voltages, there is a danger of fatal electric shock if you touch electric conductors.
Do not use the product in rooms or under unfavourable ambient conditions in which there are or could be combustible gases, vapours or dust.
- Do not use in the immediate vicinity of:
- strong magnetic or electromagnetic fields,
- transmitting aerials or HF generators.

⚠ WARNING!

The product does not perform a comprehensive test. It only checks for probable common improper wiring conditions.
■ Refer all indicated problems to a qualified electrician.
To avoid electric shock, do not touch any naked conductor with hand or skin; and do ground yourself while using the product.
The product may not indicate the presence of a live conductor because a live conductor may be present when none of the LED indicators of the product lights.
- Do not use the product in a place where explosive gas, vapour or dust is present.

In order to avoid electrical shock, use caution when working with voltage above 32 V\~ RMS, 42 V\~ peak or 60 V---. Such voltage poses a shock hazard.
■ Always keep the product dry.
The RCD test result of the product is not guaranteed to be correct.
The LED indicators of the product may light up weakly depending on the distributed capacitance of the electrical installation.

If a plug adaptor has to be used to test a shockproof socket or a lead connection, ensure that this plug adaptor is in a perfect condition and that the protective conductor connection of the plug adaptor is continuously connected. Using plug adaptors without continuous protective conductor leads to faulty test results.

The product cannot detect an inversion of the neutral (N) and the earth (PE) conductor.

The product is only intended for temporary connection (< 2 minutes) to shockproof sockets. The product is not intended for permanent operation!
The product is not intended for determining the absence of voltage on electrical systems.
The product is intended for measurements in dry environments.
The product must be used only in earthed mains and at a nominal voltage of 220–240 V\~.
Insulating conditions on site (e.g. insulating mat, wooden ladder, insulating safety shoes) might impact the correct functioning of the product.
■ Work on live parts and electrical components of all kinds is dangerous! Immediately before and after use: Check the product for correct functioning at a correctly wired shockproof socket.

Do not use the product

• if one or more of the LED indicators are not working,
• if it does not seem to be ready for operation or
• if the surface of the housing exhibits visible damage!

Before use: Always check the product for damages.
- Do not dismantle the product!
The product must be protected against contamination and damaging of the housing surface.

Before use

- Check the consignment for completeness and for signs of visible damage. If any damage is found, the product must not be used.

■ Remove all packaging material from the product.

Use

● Testing the socket wiring

Plug the product into the shockproof socket to be tested.
The 3 combined LED indicators N, PE 2 and L 3 indicate the test result:

N 1	PE 2	L 3	Test result
×	√	√	Correct wiring
×	√	×	Missing/interrupted earth (PE)
×	×	√	Missing/interrupted neutral
√	√	×	Reversed live and neutral
√	×	√	Reversed live and earth
×	×	×	Missing/interrupted live
		√ = on / = off

RCD test

⚠ WARNING! The product is a simple indicator and cannot be used as a replacement of a professional RCD tester.

• Check for correct wiring of all shockproof sockets on the branch circuit under the monitoring of the RCD to be tested.
  Plug the product into the shockproof socket, which is under the monitoring of the RCD to be tested. Verify that the shockproof socket's wiring is correct (see "Testing socket wiring").

■ Press RCD TEST to check the tripping function of an upstream RCD ( I = 30 mA):

Action Result

The RCD trips. Tripping function is working.

The RCD does not trip. Have the RCD or the entire electrical installation checked immediately by a qualified electrician.

i NOTES: Once the RCD is tripped off, the N 1, PE 2, L 3 and IΔn > 30mA 6 LED indicators turn off. If these indicators do not turn off, there might be a problem in your RCD (or) electrical installation. Contact a qualified electrician immediately.

● Cleaning and care

- Do not allow liquids to enter the product. Otherwise the product may be damaged.

• Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions since these could damage the housing or even impair operation.
  ■ Use a dry, lint-free cloth for cleaning.
  The product is maintenance-free. No components need to be maintained by you inside the product.
• Keep the product clean to ensure fault-free operation.

Storage

■ Always store the product in a dust free environment.
■ Store the product in a dry location.

● Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1 - 7: plastics / 20 - 22: paper and fibreboard / 80 - 98: composite materials.

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

Warranty

The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.

The warranty for this product is 3 years from the date of purchase. Should this product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you.

The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your proof of purchase. This warranty becomes void if the product has been damaged, or used or maintained improperly.

The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts.

Warranty claim procedure

To ensure quick processing of your case, please observe the following instructions:

Please have the till receipt and the item number (e.g. IAN 123456_7890) available as proof of purchase.

You will find the item number on the type plate, an engraving on the front page of the instructions (bottom left), or as a sticker on the rear or bottom of the appliance.

If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.

You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.

Service

Service Great Britain

Tel.: [phone]

E-Mail: [e-mail]

Service Ireland

Tel.: [phone]

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [e-mail]

50 GB/IE