DAC060BGUWDB - Air Conditioning DANBY - Free user manual and instructions

Product type	Window air conditioner
Brand	Danby
Model	DAC060BGUWDB
Cooling capacity	6,000 BTU (approx.)
Dimensions (approx.)	Width: 45 cm, Height: 36 cm, Depth: 46 cm
Weight (approx.)	28 kg
Power supply	115 V ~ 60 Hz, 5 A (approx.)
Plug type	3-prong with grounding
Operating modes	Cooling, Dry, Fan, Auto
Fan speeds	Low, Medium, High, Auto
Remote control	Included with AAA batteries
Special features	Timer (on/off), Sleep, Energy saver, Ionizer, Follow me
Air filter	Washable, clean every 2 weeks
Care and cleaning	Clean filter with lukewarm soapy water; Exterior with a soft damp cloth
Safety	Grounding required; Do not use extension cord; Do not install through wall
Installation	Single or double window, tilt outward 3° to 4°
Warranty	1 year parts and labor (in workshop)
Spare parts and repairability	Filter, remote control, batteries; Danby after-sales service
Error codes	AS, HI, LO, Evaporator error
General information	Manual available in French, English, Spanish

Frequently Asked Questions - DAC060BGUWDB DANBY

How to correctly install the air conditioner in a window?

First, fix the 'L' bracket at the top of the cabinet. Install the side curtains by sliding them into the channels. Place the unit in the window, pull down the top sash, and extend the curtains. Secure each curtain with 13 mm screws. Use the adhesive foam seal to close the opening between the windows. Ensure the unit is tilted outward 3° to 4° to allow water drainage.

How often should the air filter be cleaned?

The air filter should be cleaned approximately every 2 weeks. A light on the control panel will illuminate to remind you. To clean, remove the filter, vacuum debris, wash with lukewarm soapy water (max 40°C), rinse, and dry thoroughly before reinstalling. Press the 'Filter' button to resume normal operation.

What to do if the unit displays an error code?

Possible error codes are AS (ambient temperature sensor error), HI and LO (temperature sensor errors), and an evaporator sensor error. If a code appears, unplug the unit, wait 5 to 10 minutes, then plug it back in. If the error persists, contact Danby after-sales service at 1-800-263-2629.

The remote control no longer works, what should I do?

First check the batteries: make sure they are inserted correctly (+/-) and not depleted. Replace with new AAA alkaline batteries if necessary. The remote works up to 8 meters from the unit. Ensure no obstacles (curtains, etc.) block the receiver on the control panel. If the problem persists, reset the remote by pressing the 'Default' button.

What are the different operating modes?

The unit offers 4 modes: Cooling (to lower temperature), Dry (to remove humidity, fan speed auto), Fan (to circulate air without cooling), and Auto (automatically chooses mode based on ambient temperature). Use the 'Mode' button on the panel or remote to switch between them.

Why does water drain inside the house?

This is usually due to insufficient tilt of the unit toward the outside. The unit should be tilted downward about 3° to 4° (a height difference of 19 mm to 2.5 cm between front and back). Check the tilt angle and adjust if necessary. In very hot and humid weather, slight dripping outside is normal.

The air conditioner is noisy, is this normal?

Excessive noise may be due to unstable installation in the window. Make sure the unit is properly secured and screws are tight. Operating sounds (fan, compressor) are normal. If noise persists, check that nothing is blocking the fan blades. If in doubt, contact after-sales service.

How to use the timer function?

For auto start, press the 'Timer' button once (the start indicator lights up). Use the up/down arrows to set the delay before start (in 30-minute increments up to 10 hours, then hourly). For auto stop, press the button twice and set the stop delay. Both functions can be used simultaneously.

What does the Follow Me function do?

The Follow Me function uses a temperature sensor built into the remote. Press the 'Follow Me' button on the remote to activate. The remote sends the temperature at your current location to the unit every 3 minutes, which then adjusts cooling to reach the desired temperature where you are. The corresponding indicator on the panel flashes every 3 minutes.

How to maintain the unit at the end of the season?

Before storing the unit, run it in Fan only mode for half a day to dry the inside and prevent mold. Clean the air filter and ensure it is dry. Store the unit in a dry place. To remove the unit from the window, get help to avoid falls. Check local regulations for proper disposal.

USER MANUAL DAC060BGUWDB DANBY

Owner's Manual. 1-12

CLIMATISEUR

Welcome to the Danby family. We are proud of our quality products and we believe in dependable service. We suggest that you read this owner's manual before plugging in your new appliance as it contains important operation information, safety information, troubleshooting and maintenance tips to ensure the reliability and longevity of your appliance.

Visit www.Danby.com to access self service tools, FAQs and much more. For additional assistance call 1-800-263-2629.

Note the information below; you will need this information to obtain service under warranty.

You must provide the original purchase receipt to validate your warranty and receive service.

Model Number:

Serial Number:

Date of Purchase:

Need Help?

Before you call for service, here are a few things you can do to help us serve you better.

Read this owner's manual:

It contains instructions to help you use and maintain your appliance properly.

If you receive a damaged appliance:

Immediately contact the retailer or builder that sold you the appliance.

Save time and money:

Check the troubleshooting section at the end of this manual before calling. This section will help you solve common problems that may occur.

1-800-26-Danby (1-800-263-2629)

Important Safety Information READ AND FOLLOW ALL SAFETY INSTRUCTIONS

ELECTRICAL REQUIREMENTS

All wiring must comply with local and national codes and must be installed by a qualified electrician. Check the available power supply and resolve any wiring problems before installing and operating this appliance.

The rating plate located on the right side of the appliance just above the power cord contains electrical and other technical data.

This appliance is not designed for "through the wall" installation.

GROUNDING INSTRUCTIONS

This appliance must be grounded. Grounding reduces the risk of electrical shock by providing an escape wire for the electrical current.

This appliance has a cord that has a grounding wire with a 3-prong plug. The power cord must be plugged into an outlet that is properly grounded. If the outlet is a 2-prong wall outlet, it must be replaced with a properly grounded 3-prong wall outlet.

WARNING - Improper use of the grounding plug can result in a risk of electric shock. Consult a qualified electrician or service agent if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded.

Do not connect your appliance to extension cords or together with another appliance in the same wall outlet. Do not splice the power cord. Do not under any circumstances cut or remove the third ground prong from the power cord. Do not use extension cords or ungrounded (two prongs) adapters.

If the power supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified person in order to avoid hazard.

SAVE THESE INSTRUCTIONS!

LOCATION

This air conditioner is designed for easy installation in single or double hung windows. Since window designs vary, it may be necessary to make some modifications for safe installation.

This air conditioner is not designed for vertical, slider type windows or "through the wall" installation.

Ensure that the window and frame are structurally sound and free from dry or rotted wood.

Install the air conditioner in a window on a side of the building which favors more shade than sunlight. If the appliance must be in direct sunlight, it is advisable to provide a shade awning over the appliance to ensure efficienct functioning.

Do not install the appliance where leakage of combustible gas is suspected.

This appliance is designed to evaporate condensation under normal conditions. Under extremely hot or humid conditions, excess condensation may overflow to the outside. The appliance should be installed where condensation cannot drip on pedestrians or neighboring properties.

Provide suffi cients clearance around the appliance to allow ample air circulation. The rear of the appliance should be outdoors, it should not be in a garage or another room. Keep the appliance away from obstacles and at least 76~cm (30 inches) above the ground. Ensure that curtains and other obstructions do not block air flow to the appliance.

INSTALLATION INSTRUCTIONS

REQUIRED TOOLS

• Screwdrivers: Phillips and fl at head.
• Power Drill: 3.2mm (1/8in.) diameter drill bit
  Pencil
• Measuring Tape
• Scissors
  Carpenter's Level

ACCESSIONS

The following accessories are included with the appliance and should be used during the installation.

1. 13 mm( 1/2inch) screws (x7)
2. 9.5mm (3/8 inch) screws (x4) (Factory installed on some models.)
3. Safety Lock (x1)
4. Adhesive Foam Seal (x1)
5. Regular Foam Seal (x1)
6. "L" shaped mounting bracket (x1) (Factory installed on some models.)
7. Curtain Bracket (x2)
8. Weather Stripping (x5)
9. Foam Insert (x2)
10. Side Curtains (x2)

ASSEMBLY

Note: Images in this manual are for instructional purposes only. The actual shape of the appliance may vary slightly.

Install the "L" Shaped Bracket

Attach the "L" shaped bracket to the top of the cabinet as shown below using the provided 9.5 mm (3/8 inch) screws (x4).

Note: The "L" shaped bracket may come factory installed on some models.

Install the Side Curtains

Attach the side curtains to the cabinet by sliding the curtain frame into the side channel of the cabinet as shown below.

The curtains are labeled "left" and "right on the frames. This refers to the left and right sides of the appliance when facing the front of the appliance.

INSTALLATION INSTRUCTIONS

INSTALLATION

Cut the regular foam seal to fit the area of the window sill that the air conditioner will rest on.

Place the air conditioner into the window with the "L" shaped mounting bracket positioned in front of the upper sash. The bottom of the cabinet should be positioned on the recessed portion of the window frame. Pull the upper window sash down until it rests just behind the front flange of the "L" shaped mounting bracket.

Expand the side curtains on each side and secure the top of the frames to the window sash using one 13mm (1/2 inch) screw on each side of the "L" shaped mounting bracket.

Attach the clamps on the lower part of each curtain to the window sill using one 13mm (1/2 inch) screw on each side of the cabinet.

Place the adhesive foam seal into the opening between the inside and outside windows and attached the safety lock to the outside window frame using two 13mm (1/2 inch) screws.

Check the Tilt Angle

The air conditioner should be tilted downward towards the outside approximately 3^ to 4^ . This tilt will encourage any condensed water to drain to the outside. If any condensed water leaks to the inside of the house, check the tilt angle and adjust as necessary.

Measure the tilt angle from the front of the cabinet's edge. The difference in height between the front and the back of the appliance, labeled "A" on the image below, should be approximately 19mm - 2.5cm (3/4 inch - 1 inch).

Install the Foam Inserts

The foam inserts can block any cracks or spaces in the side curtains and help maintain the energy efficiency of the appliance.

After the appliance is installed in the window, measure the width of the side curtains from the side of the appliance to the edge of the curtain.

If necessary, cut the foam insert to the correct size and then slide the foam insert into the slots in the side curtain. The supplied weather stripping can be used to block any other cracks or spaces as required.

OPERATING INSTRUCTIONS

FEATURES

1. Cabinet
2. Exterior Air Inlet
3. Interior Air Outlet
4. Interior Air Inlet
5. Control Panel
6. Air Filter (not pictured)

CONTROL PANEL

1. Up and Down Arrows: Used to adjust the set temperature in 1^ increments and the timer function in 30 minute increments up to 10 hours and then in 1 hour increments up to 24 hours.
2. Display Panel: Displays the set temperature, the ambient temperature and the timer settings. To change the temperature scale being displayed, press the up and down buttons at the same time.
3. Timer Button: Used to set the auto on and auto off timer.
4. Filter Button: The indicator light will illuminate as a reminder to check the fi tter.Once the fi tter has been cleaned, use this button to resume operation.
5. Sleep Button: Used to set the Sleep function.
6. Ionizer Button: Used to set the ionizer function.
7. Mode Button: Used to choose the operating mode.
8. Fan Button: Used to set the fan speed. The fan can be set to Low, Medium, High and Auto.
9. Remote Control Receiver: Ensure this receiver is not obscured by curtains or other items as it could impact remote control functioning.
10. Energy Saver Button: Used to set the energy saver function.
    11.PowerButton: Used to turn the appliance on or off.
11. Follow Me Indicator Light: Illuminates when the Follow Me function is active. Follow Me can only be set from the remote control.

OPERATING INSTRUCTIONS

REMOTE CONTROL

1. Mode Button: Used to choose the operating mode.
2. Energy Saver Button: Used to set the energy saver function.
3. Ionizer Button: Used to set the ionizer function.
4. Follow Me Button: Used to set the Follow Me function.
5. Sleep Button: Used to set the Sleep function.
6. LED Button: Press to turn the LED back light on or off.
7. Clock Button: Press and hold the button for 3 seconds in order to set the clock. Press the Up and Down Arrows to adjust the time in 10 minute intervals

Note: The clock feature is only available on the remote, the appliance does not have a clock. The remote clock is a 24 hour clock only.

1. Cancel Button: Cancels current Timer settings.
2. Timer Button: Used to set the auto on and auto off timer.
   10.Fan Button: Used to set the fan speed. The fan can be set to Low, Medium, High and Auto.
3. Up and Down Arrows: Used to adjust the set temperature in 1^ increments and the timer function in 30 minute increments up to 10 hours and then in 1 hour increments up to 24 hours.
4. Default Button: Press to restore the remote control default settings.
   13.Lock Button: Press this button to lock the remote control and prevent the settings from being inadvertently changed.

OPERATING INSTRUCTIONS

REMOTE CONTROL BATTERIES

The remote control requires two AAA alkaline batteries (included). Batteries should be replaced when:

a) No sound is heard when attempting to program the appliance.
b) The appliance does not respond to a command issued by the remote control.

Battery replacement:

1. Slide the rear cover on the remote in the direction of the arrow.
2. Insert two AAA batteries following the same orientation depicted inside the battery chamber (+ / -)
3. Reinstall the rear cover.
4. If the remote control will not be used for extended periods of time, the batteries should be removed.

Notes:

• Protect the remote control from high temperatures, and keep it away from radiation exposure.
• Keep the control panel receiver out of direct sunlight.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh,etc) batteries.
• The remote operates within a range of 8 meters (26 ft.) from the receiver located inside the main appliance. Any obstruction between the receiver and remote may cause signal interference, limiting the ability to program the main unit.

This Class B digital apparatus complies with the Canadian ICES-003 standard. CAN ICES-3 (B)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Changes or modifi cations not approved by the party responsible for FCC compliance could void the user's authority to operate the equipment. This appliance complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

OPERATING INSTRUCTIONS

FUNCTION INSTRUCTION

Operating Modes

There are four operating modes to choose from. Press the Mode Button repeatedly to choose the desired mode. The adjacent indicator light will illuminate to show which mode has been selected.

Cool Mode

Choose Cool Mode to set the cooling function. Use the Up and Down Arrows to choose the desired temperature. When Cool Mode is selected, the fan speed can be adjusted by pressing the fan button.

- Dry Mode

Choose Dry Mode to remove excess moisture from the air during periods of high humidity. All water pulled from the air will condense inside the appliance and drain out the back. The fan speed will be automatically set and cannot be modifi ed in Dry Mode.

- Fan Mode

Choose Fan Mode to run the internal fan without engaging the cooling function. Press the fan button repeatedly to choose the fan speed, Low, Med, High or Auto.

- Auto Mode

Auto Mode is a pre-set factory program that automatically defi nes the mode (Cool or Dry) and fan speed based on the set temperature, the ambient temperature and the ambient humidity.

Timer Function

The Timer Function can be used to turn the appliance on or off after a set period of time.

Auto On Function

1. Press the Timer Button once and the Auto On indicator light will illuminate.
2. Use the Up and Down Arrows to select the desired amount of time before the appliance should turn on. The Up and Down Arrows will add or subtract time in 30 minute increments up to 10 hours and then in 1 hour increments up to 24 hours.
3. Use the Mode Button to select the desired mode.
4. Use the Fan Button to select the desired fan speed.
5. The time selected will appear on the display panel and will count down until the appliance turns on.

Auto Off Function

1. Press the Timer Button twice and the Auto Off indicator light will illuminate.
2. Use the Up and Down Arrows to select the desired amount of time before the appliance should turn off. The Up and Down Arrows will add or subtract time in 30 minute increments up to 10 hours and then in 1 hour increments up to 24 hours.
3. The time selected will appear on the display panel and will count down until the appliance turns off.

Using Auto On and Auto Off Simultaneously

If there is a need for the appliance to turn on, run for a set period of time and then turn off, the Auto On and Auto Off functions can be used at the same time by fi rst setting one and then the other. Both indicator lights will illuminate and the display will count down to the appliance either turning off or on, whichever function was set fi rst.

Note: The timer will not cycle the appliance on and off indefinitely. The Auto On and Auto Off timers will function one time and then the appliance will return to regular functioning.

Turning the appliance off, pressing the default button on the remote or unplugging the appliance will clear all memory settings, including the timer.

OPERATING INSTRUCTIONS

Follow Me Function

There is a temperature sensor built into the remote control that will continuously collect the current room temperature. Keep the remote control with you and the appliance will automatically adjust the set temperature based on the current temperature where you are located to reach the most comfortable condition and temperature.

Press the Follow Me button to activate the Follow Me function. The remote will display the current temperature at its location. The remote will send a signal to the air conditioner every 3 minutes, so long as you remain within range of the appliance.

The Follow Me light on the control panel of the appliance will illuminate for 5 seconds every three minutes to indicate that it has received a signal from the remote. If the appliance does not receive a signal from the remote during any 7 minute interval, it will beep to indicate that the Follow Me mode has ended.

The maximum distance for the Follow Me feature is 8 meters (26 feet). This feature is available in Cool and Auto modes.

Sleep Function

The Sleep Function can be used to conserve energy during sleeping hours.

When selected, the set temperature will increase by 1^ / 2^ every half hour for one full hour. The appliance will hold the new set temperature for 6 hours before automatically returning to normal operation.

The Sleep Function can be canceled at any time by pressing the Sleep Button.

Energy Saver Function

The Energy Saver Function will automatically cycle the fan on and off when the compressor is not in use to minimize how often the compressor needs to turn on. This function is available in Cool, Dry, Auto Cool and Auto Fan modes.

The fan will continue to run for 3 minutes after the compressor turns off. The fan will then cycle on for 2 minutes in 10 minute intervals until the ambient temperature is above the set temperature, at which point the compressor will turn on and cooling will resume.

Ionizer Function

The ionizer Function is a form of air purifi cation that negatively charges the air. Dust particles, pollen and other particles in the air cannot pass through the fi iter when they are negatively charged. This ensures that the maximum amount of dust and dirt are removed from the air. Additionally, the ionizer function helps to remove unwanted odors from the air.

CARE & MAINTENANCE

AIR FILTER

The air fi ler should be cleaned approximately every 2 weeks. The air fi ler may require more frequent cleaning if there is signifi cant dander or fur in the air.

Approximately every two weeks, the fi liter indicator light on the control panel will illuminate as a reminder to clean the fi liter. Follow the steps below to clean the fi liter and return the appliance to normal functioning.

1. The air fi liter is located behind the front intake grill. To remove the air fi liter, grasp the fi liter tab on the right side of the grill and slide it out to the right. If the front intake grill has two indents, pull the grill forward to remove the air fi liter.
2. Use a vacuum cleaner with a soft brush attachment to remove any large debris or dust build up from the air filter.
3. Wash the filter in lukewarm, soapy water, below 40^ (104^) , or use a neutral cleaning agent.
4. Rinse the filter with clean water and dry thoroughly before reinstalling in the appliance.
5. Press the fi lter button on the control panel to resume normal functioning.

Note: Do not operate the appliance without the air fiiter installed.

ERROR CODES

If the display panel shows any of the below error codes, unplug the appliance, let it stand for 5-10 minutes and then plug it back in. If the error persists, call for service.

AS - Room temperature sensor error

HI - Temperature sensor error

LO - Temperature sensor error

• Evaporator temperature sensor error

CLEANING

To avoid possible electric shock, ensure that the appliance is unplugged before performing any cleaning or maintenance.

The outside of the appliance can be wiped clean with a soft cloth or with a lukewarm, damp cloth if necessary.

Do not use gasoline, benzene, thinner or any other chemicals to clean this appliance as these substances can cause damage to the finish and deformation of plastic parts.

Never pour water directly onto the appliance as this will cause deterioration of electrical components and wiring insulation.

END OF SEASON CARE

Before removing the appliance from service for the year, operate the appliance on high fan mode for half a day to ensure the inside of the appliance is dry. This will help avoid the growth of mold or mildew inside the appliance. Ensure the filter is clean and dry. Store the appliance covered in a dry location.

Note: When installing or removing the appliance from the window, ensure that caution is taken to prevent it from falling backward. It is recommended that installation or removal is completed with assistance to prevent injury to persons or damage to property or the appliance.

DISPOSAL

Check for local regulatory compliance regarding approved and safe disposal of this appliance.

TROUBLESHOOTING

Danby Consumer Care: 1-800-263-2629

Hours of operation:

Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time

Friday 8:30 am - 4:00 pm Eastern Standard Time

Information in this manual is subject to change without notice.

PROBLEM POSSIBLE	CAUSE
Appliance will not operate • Plug	is not fully inserted into the wall outlet • Blown fuse or circuit breaker
Insufficient cooling	• Air filter is dirty • Restricted air flow • Appliance size is too small for application
Noise • Inadequate support in window	low installation
Odors • Formation of mold or mildew	ew on internal wet surfaces • Place an algaecide tablet in base pan; push the tablet through the grill on either side of the appliance
Water dripping inside • Appliance	is not properly angled to allow water to drain to the outside
Water dripping outside • On very hot or humid days dripping water from the back of the appliance is normal	hot or humid days dripping water from the back of the appliance is normal
Frost build up • When outdoor temperature are below 18.3°C (65°F) frost may form when the appliance is in cooling mode • Switch the appliance to fan only mode until the frost melts	peratures are below 18.3°C (65°F) frost may form when the appliance is in cooling mode • Switch the appliance to fan only mode until the frost melts

LIMITED "CARRY IN" WARRANTY

This quality product is warranted to be free from manufacturer's defects in material and workmanship, provided that the unit is used under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter "Danby") or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts are warranted for thirty (30) days from the date of purchase, with no extensions provided.

First 12 months During the first twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor's option, at no charge to the original purchaser.

To obtain service Contact the dealer where the unit was purchased, or contact the nearest authorized Danby service depot, where service must be performed by a qualified service technician. If service is performed on the unit by anyone other than an authorized service depot, all obligations of Danby under this warranty shall be void.

It is the responsibility of the purchaser to transport the appliance to the nearest authorized service depot.

Transportation charges to and from the service location are not protected by this warranty and are the responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or property caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.
2) Damage in transit or when moving the appliance.
3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.
4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating conditions (ie. extremely high or low room temperature).
5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).
6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.
7) Service calls resulting in customer education.
8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for outdoor application, including but not limited to: garages, patios, porches or anywhere that is not properly insulated or climate controlled).

Proof of purchase date will be required for warranty claims; retain bills of sale. In the event that warranty service is required, present the proof of purchase to our authorized service depot.

Warranty Service

Carry In

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: [519] 837-0920 FAX: [519] 837-0449

1-800-263-2629

04/17

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: [phone] FAX: [phone]

Bienvenue

PROBLEM CAUSE POSSIBLE

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: [phone] Telecopier: [phone]

1-800-263-2629

04/17

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: [phone] Telecopieur: 419425-8629

Bienvenido

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: [phone] FAX: [phone]

1-800-263-2629

04/17

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: [phone] FAX: [phone]

NOTES / REMARQUES / NOTAS :

NOTES / REMARQUES / NOTAS :

MODEL • MODELE • MODELO

DAC060BGUWDB