USER MANUAL W 500 WallSprayer WAGNER
Translation of the original operating instructions
MANY THANKS FOR PLACING YOUR TRUST IN US
We would like to congratulate you on purchasing this brand product from Wagner; we are sure that you will enjoy working with it greatly.
Please read the Operating Manual carefully and observe the safety information before starting the device. Store the Operating Manual in a safe place close to the product in case it needs to be used by someone else.
We would be happy to be of assistance if you have any questions, suggestions or requests. Please contact us via the phone number included on the back page or via our homepage, www.wagner-group.com/service.
Contents
1.Explanation of symbols used 19
2. General Safety Instructions 19
3. Safety Instructions for Spray Guns 21
4.Description/ Scope of delivery 22
5. Field of application 23
6. Coating Materials Suitable for Use 23
7. Coating Materials Not Suitable for Use 23
8. The following materials can only be processed with optional accessories: 23
9.Preparation of the workplace. 23
10.Preparation of the Coating Material 24
11.Start-up 24
12. Settings on the ON/OFF switch. 25
13. Selecting the Spray Setting (Fig. 6) 25
14. Adjusting the Material Volume (Fig. 8) 26
15.Spray Technique 26
16. Interruption of Work 26
17. Taking Out of Operation and Cleaning. 27
18.Maintenance 28
19. Spare Parts 28
20. Accessories 29
21.Environmental protection. 29
22. Important Note regarding Product Liability! 29
23. Correction of Malfunctions 30
24. Technical Data. 31
3+1 years guarantee 32
1. Explanation of symbols used
| This symbol indicates a potential danger for you or for the device. Under this symbol you can find important information on how to avoid injuries and damage to the device. |
| Danger of electrical shock |
| Indicates tips for use and other particularly useful information. |
| Devices and accessories marked with this symbol are suitable for processing high-viscosity materials such as e.g. interior wall paints (dispersion and latex paints). If a material bears this logo, it is particularly well suited for use with the relevant device. |
2. General Safety Instructions
Caution!
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refer to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Safety at the workplace
a) Keep your workplace clean and well lit. Disorder or unlit workplaces may result in accidents.
b) Never use the tool in hazardous areas that contain flammable liquids, gases or dusts. Power tools generate sparks that can ignite the dust or vapors.
c) Keep children and other persons away when using the power tool. You can lose control of the tool if you are distracted.
2. Electrical Safety
a) The tool plug must fit into the socket. The plug may not be modified in any form. Do not use adaptor plugs together with protective-earthed tools. Unmodified plugs and suitable sockets reduce the risk of an electric shock.
b) Avoid physical contact with earthed surfaces such as pipes, heating elements, stoves and refrigerators. The risk through electric shock increases if your body is earthed.
c) Keep the equipment away from rain and moisture. The risk of an electric shock increases if water penetrates electrical equipment.
d) Do not misuse the mains lead by carrying the tool by the lead, hanging it from the lead or by pulling on the lead to remove the plug. Keep the lead away from heat, oil, sharp edges or moving tool parts. Damaged or twisted leads increase the risk of an electric shock.
e) If you work outdoors with a power tool, only use extension cables suitable for outdoor use. The use of an extension lead that is suitable for outdoors reduces the risk of an electric shock.
f) If you cannot avoid using the tool in a damp environment, use a residual current operated circuit-breaker. Using a residual current operated circuit-breaker avoids the risk of electric shock.
3. Safety of Persons
a) Be attentive. Pay attention to what you are doing and work sensibly with a power tool. Do not use the tool if you are tired or under the influence of drugs, alcohol or medication. Just a moment of inattention while using the tool can lead to serious injuries.
b) Wear personal safety equipment and always wear safety goggles. Wearing personal protective equipment, such as dust mask, non-slip safety shoes, safety helmet or ear protection, depending on the type of power tools, reduces the risk of injury.
c) Avoid accidental starting-up. Ensure that the switch is in the "OFF" position before inserting the plug into the socket. Accidents can occur if you carry the power tool while your finger is on the switch or if you connect the power tool to the power supply which it is on.
d) Remove setting tools or wrenches before switching on the power tool. A tool or wrench that is in a rotating tool part can lead to injuries.
e) Avoid an unnatural posture. Ensure that you are standing securely and have your balance at all times. This ensures that you can control the tool better in unexpected situations.
f) Wear suitable clothing. Do not wear wide clothing or jewelry. Keep your hair, clothes and gloves away from moving parts. Loose clothing, jewelry or long hair can be caught in moving parts.
a) Do not overload the tool. Use the power tool designed for the work that you are doing. You work better and safer in the specified performance range if you use the suitable power tool.
b) Do not use power tools whose switch is defective. A power tool that cannot be switched on or off is dangerous and has to be repaired.
c) Remove the plug from the socket before carrying out tool settings, changing accessories or putting the tool away. This precautionary measure prevents unintentional starting of the tool.
d) Store unused power tools so that they are inaccessible to children. Do not let persons use the tool who are not familiar with it or who have not read these instructions. Power tools are dangerous when they are used by inexperienced persons.
e) Take proper care of your tools. Check whether the moving parts function trouble-free and do not jam, whether parts are broken or damaged so that the tool function is impaired. Have damaged parts repaired before using the tool. Many accidents have their origin in power tools that have been maintained badly.
f) Use the power tool, accessories, insert tools, etc. in accordance with these instructions and in a fashion specified for this special tool type. Take the working conditions and the activity to be carried out into consideration. The use of power tools for purposes other than the intended ones can lead to dangerous situations.
5. Service
a) Have your tool repaired only by qualified specialist personnel and only with original spare parts. This ensures that the tool safety is maintained.
b) If the supply cord is damaged, it must be replaced by the manufacturer or it's service agent or a similarly qualified person in order to avoid a safety hazard.
3. Safety Instructions for Spray Guns
- Caution! Wear breathing equipment: Paint mist and solvent vapors are damaging to health. Always wear breathing equipment and only work in well ventilated rooms or using supplementary ventilating equipment. It is advisable to wear working clothing, safety glasses, ear protection and gloves.
CAUTION: DANGER OF INJURY!
Never point the spray stream towards human beings or animals.
Sockets and plugs must be masked. Risk of an electric shock as a consequence of sprayed material entering the socket!
- Do not use the spray guns to spray flammable substances.
- The spray guns are not to be cleaned with flammable solvents.
- Caution against dangers that can arise from the sprayed substance and observe the text and information on the containers or the specifications given by the substance manufacturer.
- Do not spray any liquid of unknown hazard potential.
- The device may not be used in workplaces covered by the explosion-protection regulations.
- To avoid the hazard of explosion when spraying, provide for effective natural or artificial ventilation.
- There must be no sources of ignition such as, for example, open fires, smoke of lit cigarettes, cigars and tobacco pipes, sparks, glowing wires, hot surfaces, etc. in the vicinity during spraying.
- Ensure that no solvent vapors are sucked in by the unit. Do not spray onto the unit!
- The spray gun is not a toy; children must therefore not be allowed to handle it or play with it.
- Before working on the spray gun remove the power plug from the socket.
- Cover areas that are not to be sprayed. When working keep in mind that wind, for example, may transport paint mist over great distances and cause damage.
- The units may only be used with a functional valve. If paints rises in the ventilating hose (Fig. 1, item 18) do not operate the unit further! Dismantle and clean the ventilating hose, valve and diaphragm and replace the diaphragm if necessary.
- Do not lay the spray gun.
- The device is equipped with a thermal release which disconnects the device in case of overheating. In this case, turn off the device, remove the plug and let the device cool down for at least 1/2 hour. Eliminate the cause of heating, e.g. bent hose, soiled air filter, slots for air intake covered.
With original WAGNER accessories and spare parts, you have the guarantee that all safety regulations are fulfilled.
4. Description/ Scope of delivery
| Description/ Scope of delivery (Fig. 1) |
| 1 Air cap 2 Nozzle | |
| 3 Spray jet adjustment ring 4 Union nut | |
| 5 Wall Extra I-Spray spray attachment 6 Trigger | |
| 7 Material volume regulation 8 Handle | |
| 9 Combined ON/OFF and speed switch 10 Air hose |
| 11 Carrying belt 12 Air filter | |
| 13 Air screen 14 Mains lead | |
| 15 Spray gun holder 16 Container | |
| 17 Valve 18 Ventilating hose | |
| 19 Feed hopper 20 Stirring rod | |
| 21 Practice poster 22 Lubricating grease (with illustration)* |
- This is inside the container: remove it before starting operations!
5. Field of application
W 500 has been specially developed for the application of interior wall paints. Special spray attachments are required to process low-viscosity materials such as paints, glazes etc.. These can be found under "Accessories".
6. Coating Materials Suitable for Use
Interior wall paint (dispersions and latex paint)
7. Coating Materials Not Suitable for Use
Materials that contain highly abrasive components, facade paint, caustic solutions and acidic coating substances. Flammable materials.
8. The following materials can only be processed with optional accessories:
Water- and solvent-based paints, finishes, primers, 2-component paints, clear finishes, automotive finishes, staining sealers and wood sealer-preservatives.
9. Preparation of the workplace
Sockets and plugs must be masked. Risk of an electric shock as a consequence of sprayed material entering the socket!
Mask all the areas and objects that are not to be spray painted, or remove them from the work area. No liability is assumed for damage due to overspray.
Silicate paint corrodes glass and ceramic surfaces upon contact! All such surfaces must therefore be completely covered.
Pay attention to the quality of the adhesive tape used.
Do not use excessively strong adhesive tape on wallpaper and painted surfaces, in order to avoid damaging these surfaces when removing the tape. Remove adhesive tape slowly and evenly; do not use jerky movements. Do not leave adhesive tape on surfaces any longer than necessary, in order to minimise the possibility of residues when removing.
Also observe the adhesive tape manufacturer's instructions.
10. Preparation of the Coating Material
Spray material that is at least at room temperature (e.g. diluted with warm water) provides a better spray result.
Attention! Do not heat spray material above 40^ .
Interior wall paints can be sprayed undiluted or slightly diluted with the spray attachment provided. Detailed information is available in the technical data sheet of the manufacturer ( Internet Download).
- Stir the material thoroughly and dilute it in the container as per the recommended dilution (an agitator is recommended for stirring).
| Thinning recommendation |
| Sprayed material | |
| Interior wall paint (dispersion and latex paint) dilute by 0-10% |
- If the feed rate is too low even at maximum flow setting, dilute in steps of 5 - 10% until the feed rate meets your requirements.
11. Start-up
Before connecting to the mains supply, be sure that the supply voltage is identical with the value given on the rating plate.
- Attach the carrying strap to the unit. (Fig. 2)
- Unscrew the container from the spray gun.
- Aligning suction tube. (Fig. 3)
If the suction tube is positioned correctly, the container contents can be sprayed without almost any residue.
When spraying horizontal surfaces, turn suction tube forward. (Fig. 3 A)
When spraying objects overhead, turn suction tube back. (Fig. 3 B)
We recommend orienting the feed tube to the rear, to ensure optimal coating of walls and ceilings.
- Place the container on a paper base and pour in the prepared coating substance with the aid of the feed hopper included in the scope of supply (Fig. 1, 18).
Screw the container tightly onto the spray gun.
- Connect the front part with the rear part of the gun. (Fig. 5)
- Mount the air hose (Fig. 4, a + b). Insert the air hose firmly into the connection of the unit and the gun handle. The position of the hose is not relevant.
- Put the machine down only on a level, clean surface. Otherwise, the gun may suck in dust, etc.
- Sling on the carrying strap with the unit.
- Press the ON/OFF switch at the device.
12. Settings on the ON/OFF switch
The W 500 has a multi-stage On/Off switch. This allows the power of the unit to be adjusted to the material used, in order to optimise the spray pattern and reduce the spray mist.
Switch in Position "0" Unit switched off
Switch in Position "1" Unit switched on to speed stage 1
(for working with very thin materials)
Switch in Position "2" Unit switched on to speed stage 2
(for working with more viscous materials)
For thin materials the spray mist can be reduced and energy saved by switching to speed stage 1.
13. Selecting the Spray Setting (Fig. 6)
WARNING! Danger of injury! Never pull the trigger guard while adjusting the air cap.
2 different spray jet shapes can be set by turning the adjustment ring (fig. 6, 1)
Fig. 7 A = vertical flat jet → for horizontal surfaces
Fig.7 B = horizontal flat jet for vertical surfaces
Use the red adjustment lever to also switch between a wide () and a narrow (D) spray jet.
14. Adjusting the Material Volume (Fig. 8)
Set the material volume by turning the regulator on the trigger guard of the spray gun
lower material volume
higher material volume
An average flow setting provides the best result for most wall paints.
15. Spray Technique
- Cover all surfaces not to be sprayed.
- It is advisable to test the spray gun on cardboard or a similar surface to find the correct setting.
Important: Start at the edge of the area to be sprayed. Start the spray movement first of all, and then press the trigger. Avoid interruptions within the area to be sprayed.
The spray movement should come from the arm, not just from the wrist. This ensures that a uniform distance is maintained between the spray gun and the spray surface during the spray operation. Select a distance of 20 - 30cm , depending on the desired spray jet width.
Fig. 9 a: CORRECT Even distance to the object.
Fig. 9 b: INCORRECT An uneven distance will result in uneven paint application.
- Move the spray gun evenly cross-wise or up-and-down, depending on the spray pattern setting.
- An even movement of the spray gun results in an even surface quality.
- If nozzle and air cap are soiled, clean both parts with water and solvent.
"Cross spray" when using paint with a poor covering capacity or if the surface is highly absorbent (Fig. 10).
Interior wall paint in strong colour shades should be applied at least twice (allow first paint coat to dry first). This will ensure good coverage.
16. Interruption of Work
- Turn the machine off.
- During longer breaks, vent the container by briefly opening and then closing it again.
- Clean nozzle openings after an interruption in operation.
17. Taking Out of Operation and Cleaning
Proper cleaning is the prerequisite for problem-free operation of the paint application device. No warranty claims are accepted in case of improper or no cleaning.
1) Turn the machine off.
2) Divide the spray gun. Press the hook (Fig. 5 "click") slightly downwards. Turn the gun front part and gun rear part against each other.
3) Screw of the container and empty it. Pull out the suction tube with container seal.
4) Preclean the container and feed tube with a brush. Clean the ventilating bore (Fig. 11, 1).
We recommend the use of a common household washing-up brush to clean the container.
5) Pour water or solvent into the container. Screw the container back on. Do not use flammable materials for cleaning purposes.
6) Assemble the gun again (Fig. 5).
7) Turn on the machine and spray the water or solvent into a container or a cloth.
8) Repeat the above procedure until the water or solvent emerging from the nozzle is clear.
9) Turn off the machine and divide the spray gun.
10) Screw of the container and empty it. Pull out the suction tub with container seal.
CAUTION! Never clean seals, diaphragm and nozzle or air holes of the spray gun with metal objects.
The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe.
11) Pull the ventilating hose (Fig.12, 1) at the top from the gun body. Screw off the valve cover (2). Remove the diaphragm (3). Clean all the parts carefully.
12) Remove the adjustment ring (fig. 13, 1) carefully from the union nut (2).
13) Unscrew the union nut (fig. 13, 2) and remove the air cap (3), air screen (4), and nozzle (5). Clean the air cap, air screen and nozzle with a brush and solvent or water.
14) Clean the outside of the spray gun and container with a cloth soaked in solvent or water.
15) Assemble the parts again (see "Assembly").
Assembly
The unit may only be operated with an integer diaphragm (Fig. 12, 3).
1) Place the diaphragm (Fig. 12, 3) with the pin facing upwards on the bottom section of the valve. Also see the marking on the gun body.
2) Place on the valve cover (Fig. 12, 2) and screw it closed.
3) Place the ventilating hose (Fig. 12, 1) on the valve cover and on the nipple at the gun body.
4) Check the nozzle seal (fig. 14, 6) in the nozzle.
5) Place the nozzle (fig. 15, 5) on to the gun body with the recess facing downwards.
6) Put the air screen (fig. 16, 4) in the air cap (3). Put both on the nozzle (5) and secure with the union nut (2).
7) Adjust the setting ring (fig. 17, 1) so that the two "horns" grip the air cap and the red adjustment lever rests on the pin.
8) Place the container seal from below on the suction tube and slide it over the collar, while turning the container seal slightly.
9) Insert the suction tube with container seal in the gun body.
18. Maintenance
WARNING! Never operate the machine without the air filter; dirt could be sucked in and interfere with the function of the machine.
Disconnect plug before changing parts.
- Change the air filter if it is soiled.
- Remove air filter cover. (Fig. 18, a)
- Insert a new air filter into the compartment.
- Replace the cover on the unit until it latches.
In order to mount the gun more easily apply lubricating grease (enclosed) liberally to the O-ring at the gun front part (Fig. 19, 7).
19. Spare Parts
| Spare Parts List (Fig. 19) |
| Pos. Name Order No. | |
| 1 Wall Extra I-Spray spray attachment incl. 1800 ml container 2361 749 |
| 2 Spray jet adjustment ring 2363 258 | |
| 3 Un on nut 2328 903 | |
| 4 Air cap 2362 885 | |
| 5 Air screen 2362 886 | |
| 6 Nozzle | 2367 899 |
| 7 O-ring | 2362 875 |
| 8 Ventilating hose, valve cover, diaphragm | 2304 027 |
| 9 Container seal | 2328 919 |
| 10 Suction tube | 2328 922 |
| 11 Container with cover 1800 ml (only for Wall Extra spray attachment) | 2304 025 |
| 12 Handle | 0414 911 |
| 13 Air hose | 2362 880 |
| 14 Carrying belt | 2322 299 |
| 15 Air filter | 2364 990 |
| 16 Cover | 2362 881 |
| 17 Feed hopper (3 pcs.) | 2304 028 |
| 18 Stirring rod 2304 419 | |
| Lubricating grease 2315 539 | |
20. Accessories
The CLICK&PAINT SYSTEM with additional spray attachments and accessories offers the right tool for each work.
Further information about the WAGNER range of products for renovating is available under www.wagner-group.com
21. Environmental protection
The device and all accessories and packaging have to be recycled in an environmentally friendly manner. Do not dispose of the appliance with household waste. Support environmental protection by taking the appliance to a local collection point or obtain information from a specialist retailer. Leftover paint and solvents may not be emptied into drains, the sewage system or disposed of as household rubbish. It has to be disposed of separately as special waste. Please pay special attention to the instructions on the product packaging.
22. Important Note regarding Product Liability!
According to an EU directive, the manufacturer is only liable without limitation for faults in the product if all parts come from the manufacturer or have been approved by the manufacturer and have been mounted to the device and are operated properly. If third-party accessories or spare parts are used, the manufacturer is exonerated wholly or partly from his/her liability if use of the third-party accessories or spare parts have caused a defect in the product.
23. Correction of Malfunctions
| Problem Cause Remedy | |
| No coating material emerges from the nozzle | • Nozzle clogged
• Material volume setting turned too far to the left (-)
• No pressure build-up in container
• Container empty
• Feed tube loose
• Feed tube clogged
• Ventilating bore (Fig.11, C) clogged | →Clean
→Turn to the right (+)
→Tighten container
→Refill
→Insert
→Clean
→Clean |
| Coating material drips from the nozzle | • Coating material assembly at air cap, nozzle or needle
• Nozzle loose
• Nozzle seal worn
• Nozzle worn | →Clean
→Union nut tighten
→Change
→Change |
| Atomisation too coarse | • Material volume too large
• Material volume adjusting screw turned too far to the right (+)
• Nozzle contaminated
• Viscosity of coating material too high
• Too little pressure build-up in container
• Air filter heavily soiled | →Turn material volume adjusting screw to the left (-)
→Clean
→Dilute further or set Stage "2"
→Tighten container
→Change |
| Spray jet pulsates | • Coating material in container running out
• Nozzle seal worn
• Air filter heavily soiled | →Refill
→Replace
→Change |
| Coating material causes "paint tears" | • Too much coating material applied
• Viscosity of coating material too low | →Turn material volume adjusting screw to the left (-)
→Dilute less |
| Too much fog of coating material (Overspray) | • Distance to the object too large
• Too much coating material applied
• Material very thin | →Reduce distance
→Turn material volume adjusting screw to the left (-)
→Dilute less or set Stage "1" |
| Width of paint spray cannot be adjusted | • Adjustment ring is not connected to the peg on the air cap
• Air screen is clogged up | →Connect adjustment ring and peg
→Disassemble and clean |
| Device does not function | • Device overheated →Unplug the power plug, let the device cool down approx. 30 minutes, do not bend the hose, check the air filter, do not cover the intake slots |
| Paint in the ventilating hose | • Diaphragm soiled
• Diaphragm defective | →Clean the diaphragm
→Replace the diaphragm |
| Poor covering capacity on the wall | • Spray material is too cold
• Highly absorbent surface or paint with poor covering capacity
• Distance too large | The material you are spraying should be at room temperature →Cross spray (Fig. 10)
→Closer to the object |
24. Technical Data
| Technical Data |
| Max. viscosity: 3300 mPas | |
| Power source: 230 V | ~, 50 Hz |
| Power consumption: 370 W | |
| Atomizing output: 120 W | |
| Max. delivery rate 375 ml/min | |
| Double insulation: | ☐ |
| Sound pressure level*: 80 dB | (A); Uncertainty K = 4 dB |
| Sound pressure output* 93 dB (A); Uncertainty K = 4 dB |
| Oscillation level: | < 2.5 m/s²; Uncertainty K = 1.5 m/s² |
| Air hose length: | 3.5 m |
| Weight: | approx. 3.1 kg |
- Measured in accordance with EN 60745-1
The specified oscillation level has been measured according to a standard test procedure and can be used to compare against electric tools.
The oscillation level is also for determining an initial assessment of the vibrational strain.
Attention! The vibration emission value can differ from the specified value when the electric tool is actually in use, depending on how the electric tool is being used. It is necessary to specify safety measures to protect the operating personnel. These measures are based on an estimated shutdown during the actual conditions of use (all parts of the operating cycle are taken into consideration here, for example periods when the electric tool is switched off, and, when it is switched on but running without any load).
3+1 years guarantee
The guarantee runs for three years, counting from the date of sale (sales slip). The guarantee is extended by a further 12 months if the device is registered online within 4 weeks of the purchase at www.wagner-group.com/3plus1. Registration is only possible if the buyer is in agreement with the data being stored that is entered during registration. The guarantee covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or free-of-charge replacement of the defective parts. The guarantee does not cover incorrect use or commissioning or fitting or repair work which is not stated in our operating instructions. Wearing parts are also excluded from the guarantee. The guarantee excludes commercial use. We expressly reserve the right to fulfil the guarantee. The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. Wherever legally possible, we exclude all liability for injury, damage or consequential loss, especially if the tool has been used for a purpose other than that stated in the operating instructions, commissioned or repaired other than in accordance with our operating instructions or if repairs are performed by someone who is unqualified. We reserve the right to perform any repairs in excess of those stated in our operating instructions. In case of guarantee or repair, please refer to your point of sale.
Warning
If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because special purpose tools are required.
Warning: Do not connect the blue or brown wire to the earth terminal of the plug! The wires in this mains lead are coloured in accordance with the following code:
blue = neutral brown = live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
- Should the moulded plug have to be replaced, never re-use the defective plug or attempt to plug it into a different 13 A socket. This could result in an electric shock.
Should it be necessary to exchange
the fuse in the plug only use fuses approved by ASTA in accordance with BS 1362.5 Amp fuses may be used.
- To ensure that the fuse and fuse carrier are correctly mounted please observe the provided markings or colour coding in the plug.
- After changing the fuse, always make sure that the fuse carrier is correctly inserted. With out the fuse carrier, it is not permissible to use the plug.
- The correct fuses and fuse carriers are available from your local electrical supplies stockist.
We declare under sole responsibility that this product conforms to the following relevant stipulations:
2006/42/EC, 2014/30/EU, 2011/65/EU, 2012/19/EU
Applied harmonised norms:
EN 60745-1, EN 50580, EN 62233, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3
The EU declaration of conformity is enclosed with the product.
If required, it can be re-ordered using order number 2362404.
41-605 Swietochlowice
T+48/32/346 3700
F+48/32/3463713
ORKLA HOUSE CARE AB
Box 133
564 23 Bankeryd
Sweden
T+46(0)36376300
ROMIB S.R.L.
str.Polygonulinnr.5-7
100070 Ploiesti, judet Prahova
T+40-344801240
F+40-344801239
J. WAGNER AG
Industriestraße 22
9450 Altstätten
T+4171-7572211
F+4171-7572323
MAKIMPORT
HERRAMIENTAS, S.L.
C/Mejico n^号 6
