Flex Integral 5312 - Shaver BRAUN - Free user manual and instructions

USER MANUAL Flex Integral 5312 BRAUN

lock trimmerhead lock onoff

• Do not use the shaver near, or over, basins filled with water (e. g. bath tubs, showers etc.).

• For safety reasons, periodically check the cord for damage and replace it, if it is loose in the shaver socket. 1 Description

Low-charge light (red) (models 5316/5315 only)

Charging light (green)

• When charging the shaver for the first time, connect it to the mains and charge it (switch position «off») for at least 4 hours / model 5312: 8 hours. Then shave without the cord until the red low-charge light lights up. (Model 5314/5312: shave without the cord until the shaver runs distinctly slower.)

• Subsequent charges will take approximately 1 hour (5312: 8 hours).

• Wattage: 5 Watts Voltage range during charging: 12–240 V

• The green charging light indicates that the shaver is connected to the mains. After the cell unit is fully charged, the green charging light goes off. If later on, the charging light comes on again, this indicates that the shaver is being recharged to maintain its full capacity.

• Model 5316/5315 only: The red low-charge light lights up when the capacity has dropped below 20 %, provided the shaver is switched on. The remaining capacity will then be sufficient for 2 to 3 shaves. 4 Shaving

The shaver is delivered with the switch lock activated (position «lock»). Push the switch lock up before you shave for the first time. To avoid accidentally switching the shaver on, e. g. when travelling, push the switch lock to position «lock».

4.2 Switch positions

Shaving with the pivoting head. The pivoting cutting system auto- matically adjusts to every contour of your face. head lock Shaving with the pivoting head locked (to permit shaving in difficult areas, e.g. under the nose) trimmer The long hair trimmer is activated (for trimming sideburns, moustache and beard). off on lock trimmer head lock lock off on trimmer head lock lock trimmer head lock off on lock trimmer head lock off on lock trimmer head lock

4.3 Shaving with the cord

If the cell unit is discharged, you may also shave with the shaver connected to the mains (100–240 V ~). (If the shaver should not run immediately, charge it with the switch on position «off» for approx. 1 minute.) 5 Keeping your shaver in top shape

• After shaving, switch the shaver off. Press the release button, take off the triple shaving frame and gently tap it out on a flat surface.

• Then thoroughly clean the duo cutter block with the brush as well as the inner area of the pivoting head.

• About every four weeks, clean the duo cutter block with Braun cleaning agents.

5.2 Changing the shaving parts

The shaver foil and cutter block are precision parts that, in time, are subject to wear. Replace your foil frame and cutter block every 18 months and get a 25% better shave.* (Shaver foil and cutter block: part no. F/C505, available at your dealer or Braun Service Centres)

• (Overall evaluation from Braun users comparing their shave with new parts and those used for 18 months.) Tips for the perfect shave

• We recommend that you shave before washing, as the skin tends to be slightly swollen after washing.

• Hold the shaver at right angles (90°) to the skin. Stretch your skin and shave against the direction of beard growth.

• To ensure optimum shaving performance, we recommend to replace the shaver foil and cutter block every 18 months, or when the parts are worn. 90° 5465151_FI5312_16_MN Seite 10 Mittwoch, 4. Dezember 2002 2:29 1411

5.3 Preserving the cell unit

• In order to maintain the capacity of the cell unit, the shaver has to be discharged by shaving every 6 months approximately. Then recharge the shaver to full capacity again.

• Do not expose the shaver to temperatures of more than 50 °C for longer periods of time. 6 Accessories (available from your dealer or at Braun Service centres)

6.2 Charging cord as of 12 V