DAI 29 - Iron TEAM - Free user manual and instructions

Product type	Steam iron
Brand	Team
Model	DAI 29
Power supply	220-240 V / 50-60 Hz
Power	Approximately 2000 W
Tank capacity	200 ml (estimated)
Temperature setting	Yes, positions MIN to MAX (synthetic, silk/wool, cotton/linen)
Steam function	Adjustable continuous steam, double steam (steam boost)
Spray function	Yes
Dry ironing	Yes
Heating indicator	Yes
Soleplate	Probably stainless steel or aluminum
Cord length	Approximately 2 m
Dimensions	Approximately 25 x 12 x 15 cm
Weight	Approximately 1.2 kg
Care and cleaning	Internal cleaning with steam function; descaling with specific product; soleplate with non-abrasive cleaner
Safety	Do not leave unattended; unplug before filling and cleaning; do not immerse
Repairability	Contact an authorized after-sales service
General information	Manual available in several languages

Frequently Asked Questions - DAI 29 TEAM

How to fill the water tank?

Unplug the iron and let it cool down. Set the temperature button to MIN and the dry/steam button to the dry position. Fill through the opening without exceeding the maximum level. While ironing, unplug and fill while holding the iron horizontally.

How to adjust the temperature according to the fabric?

Turn the temperature adjustment knob clockwise until the symbol corresponding to the fabric (synthetic, silk/wool, cotton/linen) is opposite the mark. If in doubt, refer to the garment label.

How to use the steam function?

Fill the tank, plug in the iron and select the appropriate temperature. Set the dry/steam button between ✕ and for medium steam or towards for max. Wait for the heating indicator to turn off. Do not use at low temperature to avoid water dripping.

How to use the spray function?

The spray function can be used at any temperature, with or without steam. It moistens stubborn creases. Check the garment label first, as some fabrics may be marked by water contact.

How to use the double steam?

Press the double steam button to get extra steam on difficult areas and stubborn creases. Make sure the temperature is high enough (cotton/linen position).

What to do if water drips from the soleplate?

This can happen if the temperature is too low. Increase the thermostat setting so that steam forms properly. Also check that the dry/steam button is properly positioned.

How to clean the inside of the iron?

Set the dry/steam button to cleaning position (), hold the iron horizontally for one minute allowing steam to escape. This partially removes limescale. For complete descaling, use a specific product.

How to descale the iron?

Use a commercial descaling product for steam irons. Follow the dosage instructions. The steam cleaning function is only partial maintenance; regular descaling is necessary depending on water hardness.

How to store the iron after use?

Set the thermostat to MIN, unplug, empty the tank by tilting the iron. Place it vertically on its heel to cool down and let moisture evaporate. Once cold, you can store it.

What essential safety precautions are there?

Never leave the iron unattended when plugged in. Unplug before filling the tank, cleaning or storing. Do not immerse in water. Use the handle, do not touch hot surfaces. Check the condition of the cord regularly.

USER MANUAL DAI 29 TEAM

team International

White iron iron with gray body and side panel, no visible text or symbols

Dampfbügeleisen mit Spray
Steam Iron with spray
Fer à vapeur avec spray
Stoomstrijkijzer met spray
Plancha a vapor con spray
Ferro a vapor com spray
Ferro a vapore com spray

Fax [phone]

Generated by Unregistered Batch DOC TO PDF Converter 2011.3.804.1511, please register!

Copies of the I/B. Please reproduce them without any changes except under special instruction from Team International BELGIUM. The page must reproduced and folded in order to obtain a mini booklet B5 (+/- 150 mm width x 210 mm height). The page must be folded in order to keep the good numbering when you turn the page of the I/B. Don't change the page numbering. Keep the languages integrity.

Labeled diagram of an iron iron with numbered parts for identification

2

D

1. Fill opening
2. Spray nozzle
3. Double steamjet button
4. Variable steam/dry dial
5. Spray button
6. Temperature indicator
7. Temperature dial
8. Soleplate

F

☐ Please read these instructions carefully before using the appliance.
☐ Check that your mains voltage corresponds to that stated on the appliance.
☐ Never leave the appliance unsupervised when in use. Keep out of reach of children or incompetent persons.
From time to time check the cord for damages. Never use the appliance if cord or appliance show any signs of damage.
☐ Only use the appliance for domestic purposes and in the way indicated in these instructions.
☐ Never immerse the appliance in water or any other liquid for any reason whatsoever. Never place it into the dishwasher.
□ Never use the appliance near hot surfaces.
☐ Should the cord be damaged, it must be replaced by a competent qualified electrician ^(*) .
Before cleaning, always unplug the appliance from the power supply.
☐ All repairs should be made by a competent qualified electrician ^(9) .
□ Never use the appliance outside and always place it in a dry environment.
☐ Never use accessories which are not recommended by the producer. They could constitute a danger to the user and risk to damage the appliance.
☐ Never move the appliance by pulling the cord. Make sure the cord cannot get caught in any way. Do not wind the cord around the appliance and do not bend it.
☐ Never touch the hot parts of the appliance. Always use the handle.
☐ Make sure the cord does not come into contact with the hot parts of the appliance.
Before using the appliance for the first time, remove all labels and remainders from the sole plate and carefully wipe it dry.
□ Always let the appliance cool down before cleaning, storing or filling it (model with spray and/or steam).
☐ To fill the tank it is absolutely necessary to unplug the cord (model with spray and/or steam)
□ Always unplug the iron when not in use.

(*) Competent qualified electrician : after sales department of the producer or importer or any person who is qualified, approved and competent to perform this kind of repairs in order to avoid all danger. In any case you should return the appliance to this electrician.

UK STYLE PLUG WIRING INSTRUCTIONS (IN THE UK ONLY)

This product must only be used from a 13 amp power socket. If a BS1363 approved 13 amp plug is used, it should be fitted with a 13 amp fuse. The wires on the power cord are colour coded: blue = neutral, brown = live, green or green & yellow = earth.

The blue wire must be connected to the terminal marked N or coloured in black.

The brown wire must be connected to the terminal marked L or coloured in red.

The green (& yellow) wire must be connected to the terminal marked E or coloured in green (& yellow).

! BEFORE USING IRON, remove any labels from soleplate and wipe any manufacturing residue from soleplate using a soft cloth.

FILLING THE WATER TANK

Only use demineralised water. If you want to use the steam/dry dial fill the water tank as follows:

1) Unplug the iron from the outlet to let it cool down and set it horizontally on a stable level surface.

2) Turn the temperature dial to "MIN" and variable steam/dry dial to the setting.

3) Using a measuring cup, fill tank through the fill opening.

NOTE : never fill with anything but water.

TEMPERATURE SETTINGS

• You can chose the temperature setting in function with the cloth to iron.
• In order to turn the iron on, please turn the temperature knob clockwise into the required position.

DRY PRESSING

- Turn on the iron. - Set temperature dial for the desired fabric.

NOTE: be sure to check the garment label for fibre content and set for the fabric requiring the lowest temperature.

• Turn the variable steam/dry dial on position
- Set iron on heel rest and wait until temperature indicator light goes out.

STEAM PRESSING

Kind of textile	Temperature dial	Steam ironing
Synthetic (e.g. acetate, acrylic, viscose, Polyamide, polyester, ....)	MIN
	●
Silk Wool	●●
Cotton Linen	●●●MAX
CARE AND CLEANING	●●●MAX

• Fill the water tank (variable steam/dry dial on position ✗).

• Turn on the iron.
• Turn the temperature dial clockwise into the required position.
• Turn variable steam/dry dial between ✗ and 📋 for minimum steam or on the position for a larger amount of steam.

- Set the iron on its heel and wait until the temperature indicator goes out.

! Set the temperature dial within the steam range. If temperature setting is too low, water may drip from soleplate.

! Check the garment label before ironing because some cloths may be damaged when exposed to steam or water.

SPRAY

• Produces a mist for removing stubborn creases.
- Spray can be used at any temperature setting and during either dry or steam pressing. Press down the spray button to spray.
! Be sure to check the garment label for care instructions. Some fabrics may be damaged when exposed to steam or water.

STEAMJET

The steam jet feature provides additional steam for removing stubborn creases.

CARE AND CLEANING

• Cleaning the inside parts of the iron is done by turning the steam/dry dial into the
• position and holding the iron horizontally for about one minute so steam can escape.
- When you turn the variable steam/dry dial into the 📄 this goes up a little bit and you can take it out.
- There is no problem. YOU JUST HAVE TO PUT IT BACK IN ITS PROPER PLACE BEFORE EACH USE. Therefore just keep it deep (in the good position) and turn it clockwise.

WHEN YOU HAVE FINISHED IRONING

• Turn temperature dial to "MIN" and unplug iron from electrical outlet.
• With soleplate facing away from you, turn iron upside down to empty water.
• Then store the hot iron on its heel rest so that any remaining moisture will evaporate.

MODE D'EMPLOI

POUR VOTRE SECURITE

REPASSAGE AVEC VAPEUR