Nutrition Mixer - Blender SILVERCREST - Free user manual and instructions

USER MANUAL Nutrition Mixer SILVERCREST

1. Overview 2
2. Intended purpose 3
3. Safety instructions 3
4. Items supplied 6
   5.How to use 6
5. Operation 7

6.1 Uses 7
6.2 Preparing food 7
6.3 Mixing/ Chopping 7
6.4 Chopping ice cubes 8
6.5 Drink immediately 8
6.6 Storage 8
6.7 Overheating protection 8

1. Cleaning 9
2. Storage 9

3. Disposal 10

4. Troubleshooting 10

5. Technical specifications 11
6. Warranty of the HOYER Handel GmbH 11

1. Overview

1 Base unit
2 Suction feet
3 Cable spool
4 Power cable with mains plug
5 Blender jug (large, min. 150 ml - max. 800 ml)
6 Blender jug (medium, min. 150 ml - max. 500 ml)
7 Blender jug (small, min. 150 ml - max. 200 ml)
8 Blade attachment with a cross blade
9 Blade attachment with a flat blade
10 To Go lid (2x) and keep-fresh lid (1x)
11 Opening for drinking
12 Drinking closure
13 Nose (3x at each blender jug)

not shown:

14 Recipe book

Thank you for your trust!

Congratulations on your new nutrition mixer.

For a safe handling of the device and in order to get to know the entire scope of features:

• Thoroughly read these user instructions prior to initial use.
• Above all, observe the safety instructions!
  The device should only be used as described in these user instructions.
• Keep these user instructions for reference.
• If you pass the device on to someone else, please include this copy of the user instructions. The user instructions are a part of the product.

We hope you enjoy your new nutrition mixer!

Symbol on your device

The food-safe material of devices with this symbol will not change the taste or smell of food.

2. Intended purpose

The nutrition mixer is ...

... for mixing whole-fruit beverages (smoothies) and chopping ice cubes. For this purpose, use the blade attachment with the cross blade 8. ... for chopping solid foods (e.g. nuts). For this purpose, use the blade attachment with the flat blade 9.

The device is designed for private, domestic use. The device must only be used indoors. This device must not be used for commercial purposes.

Foreseeable misuse

WARNING! Risk of material damage!

• Thick or firm peels, (e.g. of citrus fruits, pineapple), stems and pips of stone fruits (e.g. cherries, peaches, apricots) must be removed before blending.
  The device must not be used to chop especially hard food such as e.g. bones or nutmecs.

3. Safety instructions

Warnings

If necessary, the following warnings will be used in these user instructions:

DANGER! High risk: failure to observe this warning may result in injury to life and limb.

WARNING! Moderate risk: failure to observe this warning may result in injury or serious material damage.

CAUTION: low risk: failure to observe this warning may result in minor injury or material damage.

NOTE: circumstances and specifics that must be observed when handling the device.

Instructions for safe operation

• This device must not be used by children.
  Children must not play with the device.
  The device and the power cable must be kept away from children.
• This device can be used by people with restricted physical, sensory or intellectual abilities or people without adequate experience and/ or understanding if they are supervised or instructed on how to use this device safely and if they are aware of the resulting hazards.
• If the mains power cable of this device should become damaged, it must be replaced by the manufacturer, the manufacturer's customer service department or a similarly qualified specialist, in order to avoid any hazards.
• This device is not intended to be operated using an external timer clock or a separate remote control system.
  Disconnect the mains plug from the wall socket...

... when it is not supervised,

... before you assemble or disassemble the device, and

... before you clean the device.

Clean the blade attachments, the blender jugs and the lids with warm water and a bit of detergent or in the dish washer.
- The blades of the blade attachment are sharp. Please be very careful when handling them.
- Misuse of the device may result in injuries.
The blades of the blade attachment are sharp. Please be very careful when handling them. When washing manually, the water should be sufficiently clear that you can see the blades easily.

DANGER for children

Children must not play with packing material. Do not allow children to play with plastic bags. There is a risk of suffocation.
- Please ensure that children are not able to pull the device down from the work surface with the power cable.
- Keep the device out of the reach of children.

DANGER to and from pets and livestock

• Electrical devices can represent a hazard to pets and livestock. In addition, animals can also cause damage to the device. For this reason you should keep animals away from electrical devices at all times.

DANGER! Risk of electric shock due to moisture

The device must never be operated in the vicinity of a bathtub, a shower, a filled hand basin or similar.
The motor unit, the power cable and the mains plug must not be immersed in water or other liquids.
- Protect the motor unit, the power cable and the mains plug from dampness and dripping or splashing water.
- If liquid gets into the motor unit, remove the mains plug immediately. Have the device checked before reusing.
- Never touch the device with wet hands.
- If the device falls into water, disconnect the mains plug immediately. Only then is it safe to retrieve the device.

DANGER! Risk of electric shock

• Only plug the mains plug into the wall socket after the device has been completely assembled.
• Only connect the mains plug to a properly installed and easily accessible wall socket whose voltage corresponds to

the specifications on the rating plate. The wall socket must continue to be eily accessible after the device is plugged in.

• Ensure that the power cable cannot be damaged by sharp edges or hot points. Do not wrap the power cable around the device.
  The device is not fully disconnected from the power supply, even after it is switched off. In order to fully disconnect it, pull out the mains plug.
• When using the device, ensure that the power cable cannot be trapped or crushed.
• When removing the mains plug from the wall socket, always pull the plug and never the cable.
• Disconnect the mains plug from the wall socket...
• ... if there is a fault, ...
• ... if you do not use the nutrition mixer, ...
• ... during thunderstorms.
  Do not use the device if there is visible damage to the device or the power cable.
• To avoid any risk, do not make modifications to the device.

DANGER! Risk of injury from cutting

The blades of the blade attachment carry on rotating after the device has been switched off. Wait until the blades have come to a standstill before you remove the blender jug.
- Under no circumstances should the device be operated without the blender jug.

WARNING! Risk of material damage

Do not use the blade attachment with a flat blade for liquids!
- Thick or firm peels, (e.g. of citrus fruits, pineapple), stems and pips of stone fruits (e.g. cherries, peaches, apricots) must be removed before blending.

Do not put any ingredients with a temperature in excess of 85^ into the blender jug.
In order to prevent damage to the device, interrupt the blending process immediately if the blades of the blade attachment rotate with difficulty or not at all. Pull out the mains plug and investigate whether there is an obstruction in the blender jug or whether the contents are too viscous. Also check whether the device is assembled correctly.
Do not operate the device with empty blender jugs, as this causes the motor to overheat and may result in it being damaged.
- Only operate the device when a blade attachment is screwed onto the blender jug.
The device is designed for a maximum operating time of 60 seconds without interruption. After this, the device must remain switched off until it has cooled down to room temperature.
Only use the original accessories.
The device (base unit, power cable with mains plug) is not dishwasher-safe.
Do not use any astringent or abrasive cleaning agents.
The device is fitted with non-slip plastic suction feet. As furniture is coated with a wide array of varnishes and synthetics, and is also treated with different care products, it cannot be fully ruled out that some of these materials contain ingredients that could attack and soften the non-slip plastic suction feet. If necessary, place a non-slip mat under the device.

4. Items supplied

1 base unit 1
1 Blender jug large 5 (min. 150ml - .800ml
1 Blender jug medium 6 (min. 150ml -max. 500~ml
1 Blender jug small 7 (min. 150ml -max.200 ml)
1 blade attachment 8 (cross blade)
1 blade attachment 9 (flat blade)
2 To-Go lid, 1 keep-fresh lid 10
1 recipe book 14
1 copy of the user instructions

Unpacking

1. Remove all parts from the packaging.
2. Check that all parts are present and intact.

5. How to use

• Remove all packing material.
• Check to ensure that all parts are present and undamaged.
• Clean the device prior to its first use! (see "Cleaning" on page 9)
• Unwind the desired length of cable from the cable spool 3 on the underside of the device.
• Place the device on a dry, level, non-slip surface.

6. Operation

DANGER! Risk of electric shock!

• Only plug the mains plug 4 into a wall socket, if the nutrition mixer is fully assembled.

DANGER! Risk of injury from cutting!

• Under no circumstances should the device be operated without the blender jug 5-7.
• The blades of the blade attachments 8/9 are sharp. Please be very careful when handling them.
  The blades of the blade attachment 8/9 carry on rotating after the device has been switched off. Wait until the blades have come to a standstill before you turn over the blender jug 5-7 and screw off the blade attachment.

WARNING! Risk of material damage!

In order to prevent damage to the device, interrupt the blending process immediately if the blades of the blade attachments 8/9 rotate with difficulty or not at all. In this case, pull out the mains plug 4 and check whether there is an obstruction in the blender jug 5-7.

6.1 Uses

Blade attachment with a cross blade 8

Use the blade attachment with the cross blade 8 for mixing whole-fruit beverages (smoothies) and chopping ice cubes.

Blade attachment with a flat blade 9

WARNING! Risk of material damage!

Do not use the blade attachment with a flat blade 9 for liquids!

Use the blade attachment with a flat blade 9 for chopping solid food (e. g. nuts).

NOTE: with an operating time of approx. 10 seconds, use no more than 200g when chopping nuts.

6.2 Preparing food

WARNING! Risk of material damage!

• Thick or firm peels, (e.g. of citrus fruits, pineapple), stems and pips of stone fruits (e.g. cherries, peaches, apricots) must be removed before blending.

• Rinse or wash the fruits.

• Cut the fruit into rough pieces (approx. 3-4 cm edge length).
• For smoothies: use a sufficient amount of liquid (mineral water, juice, milk, yoghurt). We recommend a mixing ratio of 1:1.

6.3 Mixing/ Chopping

CAUTION:

• Mind the marking MAX for the maximum filling quantity.
  Depending on the hardness and consistency of the ingredients in the blender jug 5-7, do not fill it to the maximum; otherwise the blade attachment 8/9 could become clogged.
  Due to their exceptional hardness nut-megs may not be chopped.

NOTE: if the smoothie is too thick, add a little mineral water, fruit juice, milk or yoghurt to suit your taste.

1. Place the fruit pieces and any other ingredients into the blender jug 5-7 as desired. Mind the marking MAX for the maximum filling quantity.
2. Figure A: screw the required blade attachment 8/9 onto the blender jug 5-7. Ensure that the blade attachment is tightly screwed to the blender jug.
3. Figure B: turn the blender jug 5-7 around and place it on the base unit 1. The small noses 13 on the edge of the blender jug fit into the recesses at the head of the base unit 1.
4. Connect the mains plug 4 with the wall socket.
5. A slight clockwise turn of the blender jug 5-7 switches the device on. Let the device run for no more than 60 seconds.
6. A slight anticlockwise turn of the blender jug 5-7 switches the device off. Wait until the blades of the attachment 8/9 have come to a complete stop.
7. Remove the blender jug 5-7 from the base unit 1 and turn it around.
8. Unscrew the blade attachment 8/9 and ensure that the liquid drips into the blender jug 5-7.
9. Before using it again and if necessary, rinse the blade attachment 8/9 briefly under running water.
10. Disconnect the mains plug 4 from the wall socket.
11. Clean the device as soon as possible after use.

6.4 Chopping ice cubes

For chopping ice cubes the device should be switched on and off in a pulsating manner.

• Switch the device on and off 4x for up to 10 seconds each time.

6.5 Drink immediately

• Figure C: in order to drink the fresh smoothie directly from the blender jug 5-7, screw a To-Go lid or the keep-fresh lid 10 on the filled blender jug 5-7. If need open the drinking closure 12 and drink from the opening for drinking 11. After you have closed the drinking closure 12 the opening for drinking 11 and blender jug 5-7 are tightly closed. You can also enjoy your smoothie "to go" when you are out and about.

6.6 Storage

Figure C: smoothies are intended to be consumed as soon as possible. Then, it is best to put the smoothie in the refrigerator. Use the keep-fresh lid 10 for this purpose.

6.7 Overheating protection

The device has an overheating protection system. If the device has been in operation for too long thus causing the device to become too hot, it automatically switches off.

• In this case, pull out the mains plug and allow the device to cool.
• You may then put the device back into operation.

7. Cleaning

Clean the device prior to its first use!

DANGER! Risk of electric shock!

Pull out the mains plug 4 from the wall socket before cleaning the Nutrition Mixer.
The base unit 1 and the power cable with the mains plug 4 must not be immersed in water or other liquids.

DANGER! Risk of injury from cutting!

• When washing by hand, the water should be clear enough for you to see the blades of the blade attachment 8/9 easily.

WARNING! Risk of material damage!

Do not use any astringent or abrasive cleaning agents.

After every use

• Clean the device and all individual parts used after each use and remove all food residues.
• Prior to cleaning, all parts must be separated from one another (e.g. remove To-Go lid or keep-fresh lid 10 from blender jug 5-7).

Base unit

Wipe off the base unit 1 and the power cable 4, using a lightly moistened cloth. Dry with a dry cloth.

Manual cleaning

1. The accessories (blade attachments 8/9, blender jugs 5-7, and To-Go lids or keep-fresh lids 10) can be cleaned with warm water and a little detergent.

2. Afterwards, rinse all parts with clean water.

3. Allow all parts to dry completely before you put them away or use the device again.

Dishwasher

The following parts can be cleaned in the dishwasher:

• the blade attachments 8/9
  theblenderjug5-7
• the To-Go lids and keep-fresh lids 10

8. Storage

DANGER for children!

• Keep the device out of the reach of children.

DANGER!

In order to avoid accidents, the mains plug 4 must never be connected to a wall socket while in storage.

Figure D: wind the power cable 4 around the cable spool 3 at the underside of the device.
- Select a location where neither high temperatures nor moisture can affect the device.

9. Disposal

This product is subject to the provisions of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate

refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products identified with this symbol may not be discarded with normal household waste, but must be taken to a collection point for recycling electric and electronic appliances. Recycling helps to reduce the consumption of raw materials and protect the environment.

Packaging

When disposing of the packaging, make sure you comply with the environmental regulations applicable in your country.

10. Troubleshooting

If your device fails to function as required, please try this checklist first. Perhaps there is only a minor problem, and you can solve it yourself.

DANGER! Risk of electric shock!

Do not attempt to repair the device yourself under any circumstances.

Fault	Possible causes / Action
No function	·Has the device been connected to the power supply? ·Check the connection. ·Has the blender jug 5-7 been engaged properly? ·Has the overheating protection switched off the device? (see “Overheating protection” on page 8)
Blade of the blade attachment 8/9 not turning or turning with difficulty	·Switch off immediately, pull out mains plug 4 and check: Is there any obstacle in the blender jug 5-7?
Liquids are running out	·Is the quantity of ingredients filled into the blender jug too large?

11. Technical specifications

Model: SNM 700 A1

Mains voltage: 220 – 240 V ~ 50/ 60 Hz

Protection class: I

Power rating: 700 W

Max. continuous operation (KB): 1 minute

Filling volume: 150 ml – 800 ml

Symbols used

GS	Certified Safety. Devices must comply with the generally acknowledged rules of technology and the German Product Safety Act (Produktssicherheitsgesetz - ProdSG).
CE	With the CE marking, HOYER Handel GmbH declares the conformity with EU guidelines.
	This symbol reminds you to dispose of the packaging in an environmentally friendly manner.
21PAP	Recyclable materials: cardboard (except corrugated cardboard)
	The symbol identifies parts that can be cleaned in the dishwasher.

Subject to technical modifications.

12. Warranty of the HOYER Handel GmbH

Dear Customer, your device is provided with a 3 year warranty starting with the purchase date. In the event of product defects, you are entitled to statutory rights against the vendor. These statutory rights are not restricted by our warranty presented in the following.

Warranty conditions

The warranty period starts with the purchase date. Please keep the original purchase receipt in a safe place. This document is required to verify the purchase.

If within three years from the purchase date of this product a material or factory defect occurs, the product will be repaired or replaced by us - at our discretion - free of charge to you. This warranty implies that within the period of three years the defective device and the purchase receipt are presented, including a brief written description of the defect and the time it occurred.

If the defect is covered by our warranty, the repaired or a new product will be returned to you. No new warranty period starts with a repair or replacement of the product.

Warranty period and statutory claims for defects

The warranty period is not extended when the warranty has been claimed. This also applies to replaced and repaired parts. Any damages and defects already existing at the time of purchase must be reported immediately upon unpacking. Repairs arising after the expiration of the warranty period are subject to a charge.

Warranty coverage

The device was produced carefully according to strict quality guidelines and tested diligently prior to delivery.

The warranty applies to material or factory defects.

Excluded from the warranty are wear parts subject to normal wear and damages to fragile parts, e.g. switches, batteries, lamps or other parts manufactured from glass.

This warranty expires if the product is damaged, not used as intended or not serviced. For the proper operation of the product, all instructions listed in the operating instructions must be observed carefully. Any form of use and handling that is advised against in the operating instructions or warned against must always be avoided.

The product is only intended for private and not for commercial use. In the case of incorrect and improper treatment, use of force and interventions not performed by our authorised Service Centre, the warranty shall cease.

Handling in case of a warranty claim

In order to ensure prompt processing of your matter, please observe the following notes:

• Please keep the article number IAN:307629 and the purchase receipt as a purchase verification for all inquiries.
• The article number can be found on the rating plate, an engraving, the title page of your instructions (in the bottom left), or as a label on the rear or underside of the device.
• If faulty operation or other defects occur, first contact the Service Centre listed in the following by telephone or email.
• Then, you are able to send a product reported as defective free of charge to the service address specified to you, including the purchase receipt and the information on the defect and when it occurred.

Please visit www.lidl-service.com to download this and many other manuals, product videos and software.

Service Centre

GB Service Great Britain

Tel.: [phone] (£ 0.10/ Min.)

E-Mail: [e-mail]

IE Service Ireland

Tel.: [phone]

(0,08 EUR/ Min., (peak))

(0,06 EUR/ Min., (off peak))

E-Mail: [e-mail]

MT Service Malta

Tel.: [phone]

E-Mail: [e-mail](mt

CY Service Cyprus

Tel.: [phone]

E-Mail: [e-mail]

IAN:307629

Supplier

Please note that the following address is no service address. First contact the aforementioned Service Centre.

HOYER Handel GmbH

TaskoprustraBe 3

DE-22761 Hamburg

GERMANY

Indhold

De Nutrition-mixer is ...