TALIKA CT - Range hood FABER - Free user manual and instructions

USER MANUAL TALIKA CT FABER

CARE AND CLEANING 14

SOMMAIRE

FR

CONSIGNES DE SECURITE 16

CHARACTERISTIQUES 19

INSTALLATION 21

UTILISATION 24

NETTOYAGE ET ENTRETIEN 26

INHALTSVERZEICHNIS

DE

For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance.

The wire connection has to be done by specialized technician.
- The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
- The minimum safety distance between the cooker top and the extractor hood is 650~mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation).
- If the instructions for installation for the gas hob specify a greater distance, this must be respected.
- Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
- Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
- For Class I appliances, check that the domestic power supply guarantees adequate earthing.
- Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm . The route of the flue must be as short as possible.
- Regulations concerning the discharge of air have to be fulfilled.
- Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).

• If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
• If the supply cord is damaged, it must be replaced from the manufacturer or its service agent.
• Connect the plug to a socket complying with current regulations, located in an accessible place.
• With regards to the technical and safety measures to be adopted for fume discharging it is important to closely follow the regulations provided by the local authorities.

WARNING: Before installing the Hood, remove the protective films.
- Use only screws and small parts in support of the hood.
WARNING: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
- Do not look directly at the light through optical devices (binoculars, magnifying glasses...).
- Do not flambé under the range hood; risk of fire.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Children should be supervised to ensure that they do not play with the appliance.

• The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.
  Accessible parts may become hot when used with cooking appliances.
• Clean and/or replace the Filters after the specified time period (Fire hazard). See paragraph Care and Cleaning.
• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Components

Ref.	Q.ty	Product components
1	1	Cooker hood with control unit, lights, blower unit, filters
2.1	1	Upper chimney
2.2	1	Lower chimney
8	1	Air outlet grid
9	1	Reducer flange Ø 150-120
10	1	Damper (Optional)
16	1	Cover for recycling version
Ref.	Q.ty	Installation components
7.2.1	2	Fixing brackets for upper chimney
11	5	Plugs
11a	2	Plugs SB 12/10
12a	5	Screws 4,2 x 44,4
12c	10	Screws 2,9 x 6,5
12e	2	Screws 2,9 x 9,5
Q.ty		Documentation
1		Instruction booklet

The dimensions depend on the chosen version

Wall drilling and bracket fixing

As a first step, proceed with the following drawings:

• a vertical line up to the ceiling or up to the upper limit, at the centre of the area in which the hood is to be fitted;
• a horizontal line at a minimum 960mm above the cooker top.
• Mark a point (1) on the horizontal line, 249 mm to the right of the vertical reference line.
• Repeat this operation on the other side, checking that the two marks are levelled.
• Mark a reference point (2) as indicated at 210 mm from the vertical reference line and 458 mm above the cooker top.
• Repeat this operation on the other side, checking that the two marks are levelled.
• Drill at the marked points (1), using a 12mm drill bit.
• Drill at the marked point (2), using a 8mm drill bit.
• Insert the bracket plugs 11a into the holes (1) and tighten the screws.
• Insert plug 11 into hole (2).
• Place bracket 7.2.1 on the wall, about 1 - 2mm from the ceiling or from the upper limit, aligning the centre (notch) with the vertical reference line.
• Mark the wall at the centres of the bracket holes.
• Place the bracket 7.2.1 on the wall at X mm below the first bracket ( X = height of the upper chimney section), aligning the centre (notch) with the vertical line.
• Mark the wall at the centres of the bracket holes.
• Drill 8mm holes at all the marked centre points.
• Insert the wall plugs 11 in the holes.
  Fix the brackets using the 12a screws (4,2× 44,4) supplied with the hood.

Fitting the Hood canopy

• Adjust the two screws Vr , in the brackets 11a, so that they are at start of their travel (B).
• Hook the hood body to the two brackets 11a.
• Connect the Hood to the Mains Power Supply, inserting a bip switch with a contact aperture of at least 3mm .
• Open the top panel. (See the paragraph on USE)
• Open the Bottom Door by pulling it downwards with your hands
• Remove the Metal Grease Filters using the handles provided.
• From the inside of the hood body, turn screws Vr to level the h body itself.

Warning: should the rear wall not be completely flat and can the two glass panels not to be aligned, pls turn on the two knob the lower part inside the hood body until you reach the per alignment of the two glass panels.

• Fasten the safety screw 11.
• Replace the Metal Grease Filters, then shut the top panel. (See paragraph on USE)
• Disconnect the hood from the mains power supply.

Warning: Should the door encounter an obstacle while open or closing it will block. When the obstacle is removed and button is pressed again the door will open.

Warning: In the event of a malfunction, check the fuse.

Replacing the fuser

• The fuser is placed up on the left side. Turn the fuser holder indicated. Replace the fuser with one having the same features.

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

When installing the ducted version, connect the hood to the chim using either a flexible or rigid pipe 150 or 120mm , the choice which is left to the installer.

To install a 150 pipe

• To install the dumper 10
  Fix the pipe in position using sufficient pipe clamps (not s plied).

To install a 120 pipe

• To install a 120mm air exhaust connection, insert the reduu flange 9 on the dumper 10.
  Fix the pipe in position using sufficient pipe clamps (not s plied).
• Remove any activated charcoal filters.

cer

To install the hood in recycling version, the optional charcoal filter kit must be purchased.

• Remove the chimney angle bracket.
• Screw the filter cover onto the air outlet, using four screws 12c (2.9 x 12.5).
  Fix the air outlet grid 8 on the recirculation air outlet using the 2 screws 12d (2,9 x 9,5) provided.

ELECTRICAL CONNECTION

• Connect the hood to the mains supply.
• Open the upper panel by pressing the A-key (See Part "USE") for at least 2 seconds.
• Remove the metal filters (See Part "MAINTENANCE") and make sure that the connector piece of the supply cable is correctly inside the hood socket.

Chimney assembly

Upper exhaust Chimney

• Slightly widen the two sides of the upper chimney and hook them behind the brackets 7.2.1, making sure that they are well seated.
• Secure the sides to the brackets using the 4 screws 12c (2,9 x 9,5) supplied.

Lower exhaust Chimney

• Slightly widen the two sides of the chimney and hook them between the upper chimney and the wall, making sure that they are well seated.
  Fix the lower part laterally to the hood body using the 2 screws 12c (2,9 x 9,5) supplied.

Control panel

Button	Function	Display
A	Door Closed: Press and hold for approximately 2 Seconds to open the door and turn the motor on at the last speed set. Door Open: Press briefly to turn the motor Off or On.	Displays the set speed.
B	Decreases the working speed.	The number of lighted segments decreases.
C	Increases the working speed.	The number of lighted segments increases.
D	Activates/Deactivates Intensive speed. This speed is timed to run for 10 minutes. At the end of this time the system will automatically return to the speed set before. Suitable to deal with maximum levels of cooking fumes. Cannot be activated when in 24H mode.	The indicator I flashes and all the segments on the Display are lit.
	Press and hold the button for approximately 5 seconds, with all the loads turned off (Motor and Lights) and no alarms in progress, to turn the Activated Charcoal Filter Alarm On / Off.	Button "C" flashes twice - Alarm On. Button "C" flashes once - Alarm Off.
E	Activates/Deactivates 24H speed. This starts the motor at a speed that allows suction of 100 m3/h for 10 minutes every hour. This mode cannot be activated if Intensive or Delay modes are active.	Displays 24 and the segments on the Display light up in cycle.
	Press and hold the button for approximately 5 seconds, with all the loads turned off (Motor and Lights) and no alarms triggered, to turn the Remote control On / Off.	(Motor LED bar flashes twice) - Remote control On. (Motor LED bar flashes once) - Remote control Off.
F	Activate / Deactivate Delay. Can be activated with motor on (except for Intensive and 24H mode). Activates automatic shutdown of the Motor and the Lighting with a 30' delay.	Displays a Clock symbol.
	Press and hold for 5 Seconds to Activate / Deactivate Lock Keyboard mode for example in order to clean the Glass.	The Leds light up and run a start-up sequence.
G	Performs a Reset of the Filter saturation alarm when the button is pressed for approximately 3 seconds when all the users (motor + lights) are turned off	After 100 hours in operation the Drop symbol is displayed to indicate saturation of the Metal Grease Filters. After 200 hours in operation the letter C is displayed to indicate saturation of the Activated Charcoal filters.
H	Modifies the intensity of the Lighting each time the Button is pressed, in cycle.	-
I	Door Closed: When pressed and held for approximately 2 seconds opens the door half way and turns the lighting on to maximum intensity. The intensity can be modified using button H. - When the button is pressed again, the lighting turns off and the door closes. - When button A is pressed, the Lights turn off and the motor only works at the first two speeds. Door Open: Press briefly to turn the lighting On or Off.	-
L	Door Closed: Press and hold for approximately 2 Seconds to open the door, turn the motor on at speed three and turn the lighting on at maximum intensity. Door Open: When pressed and held for approximately 2 seconds turns off the motor and the lighting, cancelling any function that may be active and closing the door.	-

Warning:

During the Opening and Closing phase the panel has a guard device that reverses the direction of movement in the event of blockage during the movement itself. It performs a maximum of 6 attempts before the “ ” icon flashes to indicate actual blockage. At this point, remove the obstacle preventing movement if possible, then press and hold button L for 2 seconds. The panel will once again make a maximum of 6 attempts to close or open before reverting to blocked status if movement is not successful. In this case it will be necessary to call the Technical Service Department.

REMOTE CONTROL

This appliance can be commanded using a remote control, powered by a CR2032 type 3 V battery (not supplied).

• Do not place the remote control near heat sources.
• Do not discard the batteries with normal waste, they must be put into the specific containers.

Remote control panel

	Motor	Door Closed: Opens the door and turns the motor on at the last speed set.
		Door Open: Motor On / Off
		Pressed for 2 Seconds: a) If the door is open, Motor + Lights Off. b) If the door is closed, Opens the door and Lights + Motor On.
	-	-
	-	-
Light		Door Closed: Opens the door half way and turns the Lights on a Maxi- mum Intensity.
		Door open half way: Turns lights off and closes the door.
		Door Open: Lights On / Off.
Intensive		Activates the Intensive function.
Delay		Activates the Delay function.
		Pressed for 2 Seconds: Activates / Deactivates the 24H function.
-		Increases the working speed each time it is pressed.
-		Decreases the working speed each time it is pressed.

Metal grease filters

Filters can be washed in the dish machine. They need to be washed when Drop-sign appears on the display or in any case every 2 months, or even more frequently in case of particularly intensive use of the hood.

Alarm reset

• Press the G-key for at least 2 seconds.

Cleaning the filters

• Open the upper panel by pressing the A-key for 1 second (see Part USE).
• Open the Bottom Door by pulling it downwards with your hands.
• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards.
• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make sure that they are completely dry. (The colour of the filter surface may change throughout the time but this has no influence to the filter efficiency).
• When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing outwards.

This cannot be washed or regenerated, and must be changed when the C symbol on the display appears, or at least once every 4 months. The Alarm signal must be activated in advance.

Activating the alarm signal

• In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date.
• Turn the Lights and the Suction Motor off.

• Press and hold button D for approximately 5 seconds to enable / disable the A.C. Filters

• Symbol C flashes twice, A.C. Filter saturation alarm ACTIVATED

• Symbol C flashes once, A.C. Filter Saturation alarm DEACTIVATED

REPLACING THE CHARCOAL FILTER

Alarm reset

• Press the G-key for at least 2 seconds.

Replacing the filter

• Open the upper panel by pressing the A-key for about a second (see Part USE).
• Remove the metal filters.
• Remove the saturated charcoal filter as indicated (A).
• Fit the new filters as indicated (B).
• Put the metal grease filters in their seats.

Lighting unit

• For replacement contact technical support ("To purchase contact technical support").

i

Tableau commands Telecommande

REEMPLACEMENT DU FILTRE ANTI-ODEUR AU CHARBON ACTIF

Ia6apntHbIe pa3MepbI MeHIOCTB 3aBNCIMOCTN OT BbIbpaHHo MoDen np60pa

CbepeHne OTBepCTn B CteHe n KpePnEHe cko6

Побети Ha CTeHe:

• BepTHKaJIbHyIO JINHHIO IO IIOTOJIka HJIN IO BepXHeIg IO PeIeJIa IO IeHTpy yUacTKa, IIpeIHa3NaYeHHO TJIy YCTaHOBKN BbITJKKN;
• TROP3OHTaJIbHyIO JINHHIO Ha BbICOTe He MeHee 960 MM OT BapOuHOI NaHeJIN.
  Cipaba Ot 6a3OBoB BeptHkaJIbHOJ JInHHn H Ha paCCToHNN 249 MM OT Hee, OTMeHTb Ha roPH3OHTaJIbHOJ JInHHN TOyKy (1).
• IIOBtopHTb 3Ty OIepaIIOU c IpiOTHBONIOJKeHHoI CTOpHO bI BepTHKaJIbHOJ JINHNN H IpiOBepHTb, YTO6bI TOUKN 6blHN Ha ODNOM yPOBHe.
  AHaJIIOHnHbIM CIIIOcO6OM OTMeHTNb 6a3OByIO TOky (2) Ha paCCTo8HHN 210 MM OT BepTHKaJIbHOJINHHN H a BbICote 458 MM OT BapOuHOH IaHeJIH.
• IIOBTOPHTb 3Ty OIepaIHHO C IIPOTHBOIIOJIooKeHHOJ CTOpOHb BEpTHKaJIbHOJ JINHHN H IIpOBepHTb, YTO6bI ToKKn 6blHn Ha OJHOM yPOBHe.
• BbICBepJIINb OTBepCTnA 0 12 MM B O6O3HaueHHbIX TOUkAX (1).
• BbICBepJIHTb OTBepCTHЯ 8 MM B O6O3HaueHHbIX TOUkax (2).
  BCTaBHTbIIO6eJIHcoCKO60n11aBOTBepCTHg(1)H3ATaHYb BHTbl.
  BCTaBHTIIO6eJIb11B(2).
• IIpnIOKHTb cKO6y 7.2.1 K cTeHe Ha paCCToHnn 1-2 MM OT ITOJka HJIH BepXHero IpeJeJa H BbIPoBnHTb ee IeHTp (Pi3bl) IIO BEPTHKaJIbHOJ JInHHN.
  OTMeTHTb Ha cTeHe ueHtpaJIbHyIO ToKy OTBepCTn ckO6bl.
• IIpnIOKHTb cKO6y 7.2.1 K cTeHe Ha paCCTOaHHN X MM OT IpeIbIyIeH cKO6bI (X = BbICota BepxHe YacTH NbIMOXoJa) H bIpOBHrTb ee IeHTp (Pi3bI) IIO BepTKaJIbHOJ LHHn.
• OTMeTnTb Ha cTeHe IeHTpaJIbHyIO TOUky OTBepCTH NCKo6bl.
• BbICBepJIInTb OTBepCTHg 08MM B O6O3HaueHHbIX ToUkax.
  BCTaBHTIIO6eJIIN11BCOOTBeTCTByIOIIHNEOTBepCTHJ.
• 3aKpeIHTb cKO6bI c IIOMOIIbIO BVHTOB 12a (4,2 x 44,4), IIOCTaBJIeMbIX B KOMIIJIeKTe C H3JIeJIHem.

BCTaBBTe IBA BHNTa Vr KPOHITeHOB 11a B HCXOJHOe IOJIIOKeHHe (B).
-ПовесьтЕ КОпИС ВБТЯЖКНа 2 Коюнштейна 11a.
CoeINHHTe BbITKky c cETbIO IINTaHHI; JIJI 3TOIg yCTaHOBHTe DBYXIIIOJIOCHbI BbIKJIIOHaTeJIb C MHHImaJIbHbIM pa3BeJeHHEM KOHTAKTOB 3 MM.
- OTPpoIte BepxHIOIO IaHeJIb. (CM. pa3JeI 3KCIJIYATAUINIA)
- OTKpoIte HnKHHIOI KpbIIky, IIOrHyB ee pyKaAMN BHN3
3a cIeuaJIbHbIe pyuKN BbIbTe JnHOBbIe IJIbTpbl.
- H3Hytpn Koprnyca BbTjRkK NOrTpReyIHpYrTe 3aTjKky BnHTOB Vr, YTO6bblBcTbAHTb erO IIO yPoBHiO.

BHHMaHHe: EcIHN HeOpBHaI IOBepXHOCTb CTeHbI He IIO3BOJIaET IpaBnIbHo BbIPOBHaTb I OTPeRyIINpOBA Tb IIOJOKeHHe CTKeJIHHbIX NaHeJIe, HEO6xoJHMo IIOKpyTHb PERyIINpOBOUHbE pbluAaKKn, HaxoJdIaIeCeH BHyTpri KOpIIyCa BbITKaKN B HnKHeJ qactn

3aTnHTe IpeoXpaHHTeJIbHbI BnHT 11.
- IocTaBbTe Ha meCto JnHpOBBeI HJbTpbl N BepXHIO IaHeJI. (CM. pa3JeI KCIJIYATAUIIIN)
- OtcoeHnHTe BbITgKky OT cETH 3JIeKtpoHntaHnI.

Bhimahe: Ecn Bo Bpem paKpbTnna 3akpbTnna KpbIka BCTpeaet npenrTCTBne, Oha octaHabnBaetc; nocne ydaJeHn npenrTCTBn I NOBtOpHOro Haxatn KaBnIu KpbIka OTKpbIbaetc.

BHHMaHHe: B cIyae HeuCnpaBHOCTn IpoBepbTe COCTOHNe npedoxpaHHTeJ.

3aMeHa npedeoxpaHnteJia

• IIpeIoXpaHHTeJIb HaxoIHTcB BEpxHy HaJIeBO; IIOBePHHTe, KaK IIOKa3aHO, IIJaBkyIO BCTaBky H 3aMeHHTe IIpeIoXpaHHTeJIb Ha HObI C TaKHMH JxE XapaKTEpHCTHKaMn.

CoeHHnHn

BbIpyCK BO3DyXA I3 BCAbIBAIOUeBbITJXKIN

• HαkaTb KJIaBnIy G B TeueHne He MeHee 2 cKeYnI.

OuHcTkaΦHJbTpOB

• EcJIN CTBOPKa 3aKpbIta, oTKpoJIte ee HaJaTHeM KJIaBbHIIH A B TeueHHe OKOJI O KEyHIIbI (CM. pyKOBoIDCTBO IIO 3KcIIJIyataIH).
• OTKpoITe HNKHIOU KpbIIKky, IOTaHyB ee pyKaMn BHN3.
• BbHytB ΦHJIbTpbl IO OUpeEIN.ДЯ 3TOrO IprHkaTb Hx K 3aHHe CTOpOHe BbITJAKKn H OJHOBpeMeHHO IOTyHytB BH3.
• Octopokho IOMbIb ΦHJIbTpbl, YTObI OHn He COrHyJINcB, H IIpeI yCTaHOBKOДaTb HM IpOcoxHyTB. (IIoBIAIOJIeecCo BpemeHem H3MeHeHne IBeTa IOBepxHOCTn ΦHJIbTppa HNKOHM 06pa3OM BJIHReT Ha 3ΦΦeKTHBHOCTb ΦHJIbTpaaHH)
  -ПoctabnTBфньтбHaMeTo TaK,чTOбIpyuKa hAxOДиAcb cBnHoi HapyKHOCTopoHbI.

Takoi HJIbtp HeJIb3a MItb H BOCCTaHAbJINBaTb, eO Heo6xoJHMO MeHrTb, KOrTa Ha JHCIIeE IIOBJIaeTc cHMBOL C, HJIH He peKe OJHO paa 4 Meca. IIpeIbapHTeJIbHO Heo6xoJHMO IIpHBecTN CHHaJIH3aIHHo HAcbIeHHN oHJIbTpOB B COCTOHNHe rOTOBHocn (AKTHBHOe coCTOHNHe).

PnHBeHHe cHrHaJIn3aunH B coCToAHHe rTOBHOCTH

B BbIyKkax c peXHMOM peIHPkyJIaIIIN cHrHaJIH3aIIIN HaCbIeHHa HcJIbTpOB IOJIka 6bIb TB KJIIOueHa (PiPBEdeHa B aKTHBHOe COCTOAHHe) pIi yctAHOBKe HJIN IIOCE Hee.
- BbIKJIOHHTe OcBEIeHHe N IINBnIaTeJIb BBITrJxHO RBeHTNJIyTopa.
HaKMHTe KHOIIky D pHmepHo Ha 5 ckyHД IJI BKJIIOueHHa/OTKJIIOueHHaHJaIN3aIHN HacbIeHHy yOJIbHbIX ΦJIbTPOB.

CmboJ C mHaer 2 pa3a: cHHaJIIm3aIHHa HacbIeHNy yTOJIbHO rO hIbtpa BKJIIOUcEHA
CmMBOJI C mHaer 1 pa3: cHnHaJIH3aIHHaHacbIeHHyroJbHoro oHJIbtpa OTKJIIOUOHEA

3AMEHAФиltbTPAOT3ANAXOB HAAKTINBHOMYJIE

C6poc abapnHoo chHaJIn3aunn

• HαkaTb KJIaBnIy G B TeueHne He MeHee 2 cKeYnI.

3aMeHa _, tpa

• EcJIN CTBOPKa 3aKpbIta, OTKpOJIte ee HaJaTHeM KJIaBbHIIH A B TeueHHe OKoJI0 1 cekyHJIbI (CM. pyKOBoIDCTBO IIO 3KcIIJIyataIH).
• CnrytB kHpOBbIe NJIbTpbl.
• BbHyTB HacbIeHHbIe ΦHJIbTpbl Ha aKTHBnPoBaHHOM yTJIe, KaK yKa3aHO Ha pHcyHKe (A).
• YctaHOBHTb HOBbIe 0JIbTbI, KaK yKa3aHO Ha pHcyHKe (B).
• IIOCTaBHTb Ha MeCTo JHPOBbIe ΦHJIbTpbl.

OcbeueHne

-ДляЗамени CBETODHObaOBpaIaITeCbB O6cIyKHBaIOIINIeHTp("ДлЯпнбретенЯOBpaIaITeCbB O6cIyKHBaIOIINIeHTp").

a a a a a a a a a a a a a a a a a a a a a a a a a a a a a

a a a a a a a a a a a a a a a a a a a a a a

dclj 1 jc caiagblll no yjol aydiis ciall coy jolll l

a 1

iiial 134 aia ci jjai jai jai jai jai jai jai jai jai

L

aalblaiill (1) 120 jb

aillblil (2) 80 jbi

（1）a 11a a

.(2) _1^_2^_3^_4^_5^_6^_7^_8^_9^_10^_11^_12^_13^_14^_15^_16^_17^_18^_19^_20^_21^_22^_23^_24^_25^_26^_27^_28^_29^_30^_31^_32^_33^_34^_35^_36^_37^_38^_39^_40^_41^_42^_43^_44^_45^_46^_47^_48^_49^_50^_51^_52^_53^_54^_55^_56^_57^_58^_59^_60^_61^_62^_63^_64^_65^_66^_67^_68^_69^_ 70^_ 71 ^_ 72 ^_ 73 ^_ 74 ^_ 75 ^_ 76 ^_ 77 ^_ 78 ^_ 79 ^_ 80 ^_ 81 ^_ 82 ^_ 83 ^_ 84 ^_ 85 ^_ 86 ^_ 87 ^_ 88 ^_ 89 ^_ 90 ^_ 91 ^_ 92 ^_ 93 ^_ 94 ^_ 95 ^_ 96 ^_ 97 ^_ 98 ^_ 99 ^_ 100 ^

(jal) jall jg y g. 12 2-1 7.2.1

S ADB = S COD + S_ BDO

Cldll w gill Cldlc g

(1) x1 = x x2 = y1 ( x1,y_1) .

y jyj yj yj yj yj yj yj

Aaill wgl lcl

aill bll 80 jbi

11

12a (4.2 x 44.4)

Aa

(B) 11a 11a 11a 11a 11a 11a 11a

.11a jaiall glc aiisall Jy yaiy

Caiy 150

3j = - 1

（Juaauii jiajai）aial

Jawl oljyly yaua aalw alil

Jauaiall aabw yaaill alulalld

.

g jiu bui pao yu ci yu d gill jiljll el gai xie

aJz aiaiaaiiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaiaia

Juslll Jus

.11jdoai g

jaiai jai jia

jLus Ls jyduill jLusill

alall alalalalalalalalalalal

aagill aie

ggl 2b o gnuu pki

jswla iisaiisall gblalll jlll jlll ojswla 5jiie

g 120 150

150 la jbd s yuula u

10.2jall jg uys

auiia cuiuL piaiuu yjuyuall ayjai

120 la jz o yu wu u

9 120 2

jll jll jll jll jll jll

auiia cuiu1s plaiiydu yswall ayj p

Jg j

j j j j j j j j j j j j j j j j j j j j

aaiiaaii jj 8jj

jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll jll

#

J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J 1 J

4aill jya b

JyI yuui G

#

aal jall jial) aal ayai A clll al aal aal aal

（）

Jaiy jaiy jaiy jaiy jaiy jaiy jaiy jaiy jaiy

Jd jdlal k jslcl Jd. qillll alac elil jdlall g

y kslj gll jdl l 100

（jdlalles

1

4 45 4 C jai aai iie yiaiaaiy

Lalalolalalaiy aillil 5

4.1.1.1 0

aaii aie 1

.

1

C.A 5dD

("aiaai aaii jaiy aaiy aaiie") .