GX950 - ASUS - Free user manual and instructions

USER MANUAL GX950 ASUS

Q7297 First Edition (V1) May 2012

Copyright © 2012 ASUSTeK Computer Inc. All Rights Reserved.

No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK Computer Inc. (“ASUS”). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.

Telephone Online support

+86-21-38429911 support.asus.com

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

Telephone Support fax Online support

+1-812-284-0883 support.asus.com

ASUS COMPUTER GmbH (Germany and Austria)

Address Fax Web site Online contact

Telephone (Component) Telephone (System/Notebook/Eee/LCD) Support Fax Online support

+49-1805-010920* +49-2102-9599-11 support.asus.com

* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.

Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

REACH Complying with the REACH (Registration, Evaluation, Authorisation, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS REACH website at http://csr.asus.com/english/REACH.htm.

DO NOT throw the mouse in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in municipal waste. Check local regulations for disposal of electronic products.

ASUS Recycling/Takeback Services

ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components, as well as the packaging materials. Please go to http://csr.asus.com/english/Takeback.htm for the detailed recycling information in different regions.

Check your ASUS GX950 Gaming Mouse package for the following items:

If any of the above items is damaged or missing, contact your retailer immediately.

Specifications Summary

Connectivity Technology Wired

Dimensions (mm) Cable Length Weight

Mouse: 122(L) x 82(W) x 43(H)

1.8m with cable sleeve Mouse: 150g (adjustable) 1 x Left button / Right button / Scroll wheel 2 x Side buttons 1 x DPI button 1 x Profile switch 50 ~ 8200 dpi (adjustable) Default: 800dpi (Level 1), 1600dpi (Level 2), 3200dpi (Level 3), 5600dpi (Level 4)

Gold plated USB Specifications are subject to change without prior notice.

Knowing your ASUS GX950 Gaming Mouse

Your ASUS GX950 Gaming Mouse comes with a left button, a right button, a scroll wheel, two side buttons, a DPI button, and a specially designed Profile Switch button. 2

DPI switch Move the DPI switch forward/backward to change the mouse resolution. The DPI switch 4 LEDs light up when you move the DPI switch. See the table on the next page for the LED indications*. Profile switch / Profile indicator 5 Press the Profile switch to select a profile. The switch lights up when you press it. See the table on the next page for the LED indications**. 6 LED DPI indicator* 7 GX950 logo 8 IE Forward button 9 IE Backward button 10 Mouse feet 11 Twin-Eye Laser sensor 12 Weight base (5 x 4.5g blocks)***

*** To adjust the mouse weight, add or remove the weight blocks.

* DPI switch LED indications

** Profile switch LED indications

NOTE: The DPI levels go up and down in a cycle. When the mouse is set to Level 4, and you keep moving the DPI switch forward, the DPI level will go down to Level 1 and then go up to Level 2 and higher DPI levels. When the mouse is set to Level 1, and you keep moving the DPI switch backward, the DPI level will go up to Level 4 and then go down to Level 3 and lower DPI levels.

Connecting your ASUS GX950 Gaming Mouse

Connect your ASUS GX950 Gaming Mouse to your computer’s USB port.

Customizing your mouse (DPI values / Macro commands / Button functions)

Go to ASUS website at www.asus.com to download the latest driver and install it to customize your mouse's DPI values, Macro commands, and button functions.

Using the setup utility

Do either of the following to launch the setup utility: •

Click the ASUS ROG Gaming Mouse GX950 shortcut desktop.

Click Start > All Programs > ASUS Gaming Mouse > ASUS ROG Gaming

Right-click the icon from the Windows® taskbar, then select Launch

GX950 APP. If the screen below appears, plug your ASUS GX950 Gaming Mouse into your computer’s USB port. The utility will automatically detect the mouse and continue to the main menu. •

Displays the profile icon which is configurable in Profile 1~3 menus.

Click to reset the DPI configuration to the last settings you have saved.

Drag the slider to adjust the DPI value for each level.*

Click to reset the button settings to the last settings you have saved.

Click to display the indications of different Profile indicator colors.

Click to load a profile you have saved for your mouse.

Click to save the current profile settings to your hard disk drive.

Click to display the Options menu which allows you to adjust the mouse polling rate, configure the Angle Snapping and Lift-off features. See page 15 for details.

Click to reset all the mouse settings to the factory defaults.

Click to save the settings you have made.

Click to save the settings you have made and exit the program.

* Each profile provides four DPI levels. The DPI switch LEDs light up indicating the DPI level you are using. See page 9 for the detailed LED indications.

Click to open the Edit menu which allows you to change the profile name and profile icon.

Enter the profile name you want to use.

Click to locate the image file you want to use as the profile icon.

Select a function for each button / action from the drop down list.

* Refer to the table below for more details.

Makes the button behave like the left mouse button.

Makes the button behave like the right mouse button.

Makes the button behave like the middle mouse button.

Makes the button behave like the IE Backward button. When selected, press the button to go to the previous page you viewed.

Makes the button behave like the IE Forward button. When selected, press the button to go to the next page you viewed.

continued on the next page

When selected, press the button to run a command or series of commands which you can edit though the Edit Macro menu. See page 14 for more details.

When selected, press the button to increase the DPI value.

When selected, press the button to decrease the DPI value.

Makes the button behave like the profile switch button.

When selected, press the button to scroll leftward / rightward as a tilt wheel does.

NOTE: This function only work in the Microsoft® Office applications under the Windows® 7 / Vista operating systems.

When selected, press the button to perform a keystroke or keystroke sequence.

Rapid Fire [mouse] When selected, press the button to do a rapid fire in a click-to-attack game, which is the same as clicking the left mouse button three times.

When selected, press the button to do a rapid fire in a game using the

Spacebar to attack, which is the same as pressing the Spacebar three times.

When selected, press the button to launch your default web browser.

When selected, press the button to launch your default email application.

When selected, press the button to launch your default media player.

When selected, these buttons become playback control buttons in an active media player.

Volume Up / Down When selected, press the button to increase / decrease the system volume. Mute

When selected, press the button to turn the volume’s mute mode on/off.

When selected, press the button to launch the Calculator application.

When selected, press the button to open My Computer window.

APP When selected, press the button to launch this setup utility.

Select this item to deactivate the button.

When checked, the new instruction will be inserted before the selected instruction. Otherwise, any new instruction will be given the first priority.

Stop Clear Move up/down Instruction cycle time Loop Fire Keeping fire

Click to start recording the keystrokes and/or mouse actions.

Click to save the current macro to your hard disk drive.

Click to open the Edit Macro menu.

Check this item to record the time between pressing down and releasing a button. (Default: 12ms)

Click to stop recording the keystrokes and/or mouse actions.

Click to clear all the saved instructions. Click to move up/down the selected instruction. When Timing is unchecked, all the actions’ delay time will be the value you chose from the drop down list. Sets the macro to run at a click and stop when you click again. Sets the macro to run once at one click. Sets the macro to run when you hold down the button and stop when you release the button. Click to load a macro from your hard disk drive.

Select your mouse polling rate from the drop down list. Configuration options: 125Hz,

250Hz, 500Hz, 1000Hz (default).

Tick Angle Snapping to enable the Angle Snapping feature.

Angle snapping brings smooth and straight mouse movements. By default, Angle Snapping is disabled.

Tick Lift Off to enable the Lift-off feature, and then drag the bar to adjust the Lift-off height from the lowest to the highest. Clear the Lift Off box to automatically adjust the

Lift-off height. When the Lift-off feature is enabled, your mouse stops tracking when you lift your mouse off the mouse surface higher than the specified Lift-off height.

The GX950 mouse logo appears on the taskbar when the program is properly installed.

Click to open the main menu of the GX950 mouse setup utility.

Click to visit the ASUS official website.

Click to exit the setup utility.

Federal Communications Commission Statement 繁體中文

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • •

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification UL Mark

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

REACH Support technique

Telephone Online support

+86-21-38429911 support.asus.com

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

ASUS France SARL Adresse

+33 (0) 8 21 23 27 87

+33 (0) 1 49 32 96 99 support.asus.com

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Federal Communications Commission Statement

Sicherheitszertifikate

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

Livello 1 (predef. 800 dpi)

Livello 2 (predef. 1600 dpi)

Livello 3 (predef. 3200 dpi)

Livello 4 (predef. 5600 dpi)

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

Federal Communications Commission Statement ������������� （原文） This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

本 語 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007.

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

+1-812-284-0883 support.asus.com

Federal Communications Commission Statement Magyar

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

Federal Communications Commission Statement

CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

Telephone Online support

+86-21-38429911 support.asus.com

Telephone Fax Web site

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

Telephone Support fax Online support

+1-812-284-0883 support.asus.com

ASUS COMPUTER GmbH (Germany and Austria)

Address Fax Web site Online contact

Telephone (Component) Telephone (System/Notebook/Eee/LCD) Support Fax Online support

+49-1805-010920* +49-2102-9599-11 support.asus.com

* EUR 0.14/minute from a German fixed landline; EUR 0.42/minute from a mobile phone.

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

Specifications Summary

Dimensions (mm) Cable Length Weight

Copyright © 2012 ASUSTeK Computer Inc. Toate drepturile rezervate.

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Federal Communications Commission Statement

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification UL Mark

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Safety Certifications

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Safety Certifications

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.

800 Corporate Way, Fremont, CA 94539, USA

+1-510-739-3777 +1-510-608-4555 usa.asus.com

+1-812-284-0883 support.asus.com

+49-1805-010920* +49-2102-9599-11 support.asus.com

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.

Federal Communications Commission Statement

CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

China RoHS EFUP Labeling - 10 Years C-Tick Mark BSMI Certification

Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser

Notice No. 50, dated June 24, 2007.