TURBO 6S - Stroller ABC DESIGN - Free user manual and instructions

USER MANUAL TURBO 6S ABC DESIGN

NB: Keep these instructions for future reference!

• Combination travel system with convertible attachment
• Height-adjustable telescopic handle
  Four-position backrest
• Swivel mode and locked setting on front wheels
• Hood featuring magnetic-action viewing panel

Weight: 16.0kg
- Tested for conformity with EN 1888 : 2005
- Compatible with ABC Design "Rider" car seat
- Compatible with ABC Design "Kiddie Ride-On" buggy board

Care instructions

• The materials used to manufacture our products comply with the AZO requirement. EN71-2 and EN71-3, and light fastness standards for textiles. Nevertheless, we advise you not to leave the product exposed to bright sunlight for any length of time. No claims may be made for wear and tear or if the colours fade when exposed to strong sunlight. The fabric covers on this product can be washed by hand or on a cold cycle in the washing machine (mild detergent).
• An ABC Design rain canopy is available in retail stores offering complete protection against the rain.
  All the frames on our products have been tested for conformity with EN1888 : 2005 and have met the required standards. In order to maintain the safety of the product it is necessary to oil the moving parts or tighten the rivets as and when required. NB: Please do not use any product for lubrication other than silicone oil or silicone spray lubricant.
• Regular care and upkeep have a major part to play in maintaining the safety and value of the product. Exposure to such things as salt in the air, road-gritting salt or acid rain will encourage the onset of corrosion, as will inappropriate storage of the product.
• We recommend regular maintenance of all coated parts. In serious cases of soiling please clean the surface coating immediately.
• Check for loose parts and fastenings from time to time and tighten if necessary.

Safety instructions

Read these instructions carefully before use and keep them for future reference. Failure to read these instructions may compromise the safety of your child.

NB:

• This model is suitable for infants from 6 months (from birth with carrycot) and up to a maximum weight of 15kg .

• The net bag can carry up to 2kg .

• This pushchair is designed to transport a child.
• Do not use any accessories other than those approved by the manufacturer.
  You are advised to take your child out of the pushchair as a matter of principle when negotiating steps or flights of stairs or if the pushchair needs to be lifted or carried.
• If you are using a carrier, ensure that it is correctly attached to the pushchair.

CAUTION:

• Do not leave your child unattended.
• The only mattresses suitable for use are those up to 50mm thick.
• Use a safety harness as soon as your child can sit independently.
• This seat is not suitable for babies under 6 months old.
• Loads attached to the handle affect the stability of the pushchair.
• Before use, check that the pushchair attachment or seat is correctly engaged in position.
• This product is not suitable for jogging or skating.
• Do not make any modifications to the product which compromise its safety.
• Keep this product away from fire and other sources of heat.

Customer complaints

• No claims may be made for natural wear and tear or for damage caused by undue demands on the product or by exceeding the permissible load.
• No claims may be made for damage caused by improper use.
• No claims may be made for damage caused by incorrect assembly or operation.
• No claims may be made for damage caused by improper modifications to the product.
• Areas of rust may appear through lack of maintenance or improper care and do not constitute a fault with the product.
• Scratch marks are normal signs of wear and do not constitute a fault with the product.
• Mildew is likely to appear on textiles which are not dried out after getting wet and cannot be attributed to shortcomings in production conditions.
  The product may fade if exposed to sunlight, perspiration and detergents, or if subject to abrasion or excessive washing. therefore fading cannot be attributed to a fault with the product.

• No claims may be made for wheels which become worn out as a natural result of wear and tear.

• Opening the pushchair

Pull the handle on the stroller (1) upwards until the frame clicks into place (2).

CAUTION: Ensure that all the catches are engaged before use.

2. Fitting the wheels

Press the button (1) and insert the rear wheel in the slot (2) until it engages.

To remove the wheels, press the button (1) to release the wheels. The wheels can then be removed from the axle.

Mount the front wheels by sliding the wheel assemblies onto the prongs until they click into place.

To remove the wheel assemblies, press the button underneath the blocks and remove the assemblies.

3. Wheel locking and swivel settings

Push the lever downwards to lock the wheels.

Push the lever upwards for swivel position.

4. Operating the brake

Press the lever down to engage the brake.

Press the lever up to disengage the brake.

5. Attaching and converting the seat

Attach the seat by placing it on the frame until it clicks into place.

To convert the seat, press the buttons on both adapters and lift up the seat.

1. Attaching and removing the hood

Lower the hood down onto the attachment

To remove the hood, press the buttons in on both sides of the hood.

1. Fitting and removing the guard rail

Fit the guard rail by inserting it in the plastic mounts on both sides.

To remove the guard rail from the pushchair, press in the buttons on both sides and pull the guard rail off away from the pushchair.

To adjust the height of the guard rail, press and hold down the buttons on each side and push the bar up or down.

1. Adjusting the leg rest

To adjust the leg rest, press in the buttons on both sides and then adjust the height.

Let go of the buttons again so that the leg rest clicks into place.

1. Fastening the harness

To fasten the harness, bring the top two plastic catches together and interlock them.

Then insert the interlocked catches into the bottom part of the fastening.

Adjust the harness to a setting where the baby is held in the correct position.

1. Unfastening the harness

To open the harness, press the button on the side.

CAUTION: Always use the shoulder harness and lap belt together.

1. Adjusting the backrest

To adjust the backrest, pull the retainer on the rear of the backrest upwards and then adjust the height. When you have reached the required position, let go of the retainer to allow the backrest to remain in that position.

1. Adjusting the handle

Push the button upwards to adjust the height of the handle. When the handle is at the required height, let go of the button again so that the handle will remain locked in this position.

1. Removing the sun canopy

Undo the zip fastener on the side of the canopy.

1. Folding the pushchair

To fold the pushchair, bring the handle to its lowest position as described in point 12. Holding the button (1) down as you do so.

Now rotate the knob (2) to the left and push the handle down.

Now you can fold up the pushchair.

Note: To unfold the pushchair, follow the instructions in point 1 "Opening the pushchair".

CAUTION: Ensure that all the catches are engaged before use.

1. Opening the carrycot

Lift the side panels of the carrier.
Extend and secure the side panels by pushing the two retainers outwards into the mountings.
Make sure that the retainers are securely engaged.

1. Attaching the cot bumper

Lay the bumper in the cot, folding the top part over the edge of the carrycot.

1. Inserting the mattress

Insert the mattress in the cover.

Lay the mattress on the base.

NB: The mattress is wedge-shaped. Make sure that the raised part is at the head end.

1. Fitting the cot on the pram

Recline the back of the seat. Position the carrycot on the pram.

Take hold of the strap which is fitted to the rear of the cot and pull it through the opening provided in the seat cover.

Fasten and tighten the belt on the rear of the backrest.

Flip up the footrest at the lower end of the cot and secure the strap around the footrest. Fasten and tighten the strap.

1. Fitting the apron

Fit the closed end of the apron over the lower end of the carrycot. Extend the apron over the cot.

Secure the ends of the apron with the snap fasteners provided on the cot and cover

1. Attaching the mosquito net

Unzip the top end of the apron and pull out the mosquito net.

Pull the mosquito net over the cover and fasten it to the cover. Then fasten the apron to the mosquito net.

1. Fitting the foot muff

Undo the strap and position the liner on the seat.

Pull the five straps through the openings provided in the cover.

Now you can fasten the apron with the zip fastener on the liner.

1. Fitting the apron

Take the lower part of the foot muff out of the bag.

Zip the top and bottom parts of the foot muff together.

Secure the foot muff to the pushchair by attaching the apron to the cover using the snap fasteners provided.

1. Chartyne conHeuHoi KpbIi

OTKpoTe MoHnIO Ha 6Oky KpbIuN.

1. CknaDbBaHne cKnadHoro kpecna

TtO6bI cNoJtB cKnaHoe KpeCIO, npuBeIeIte pykU B ee Hau6oJe Hn3KOE nIoJxHeNe, KaK 3TO OINcAHO BnyKTe 12, yepxNBA B 3TO BpEa KNOpKy (1) B hAnaTOM COCTOHN.

3aTeM BpaaIte pyKoTky (2) BnEBo I npToTknHte pyKu BnH3. TepeB Bbl MoKeTe CNOKtB cKnAdHoe KpeCNo.

BnMaHHe: yTo6bI pa3NoKntb cKlJaHoe KpeCNO, cNeDyIte INHcTpyKuIN, npNBedeHHO B nyHKTe 1 «C6OpKa cKnAdHoro KpeCna».

PNEyIPEXJEHHE: Ppea nCnoB3OBAHnem y6eNTecb T TOM, YTO BCE KpeJIeHnaJeKHO 3aΦNKcnpoBaHbl.

1. C6opka nepehoCHO KPOBaTkn

IodHMMTe 6OKOBle naHEn KPOBATK.
Pa3dInbte n3aKepeNITE 6OKOBle naHEn, BbTaNKBaB a 6a KCaTopa HApKy B dePekATENI.

Y6eIITecb B TOM, yTO ΦικCaTOpbl HaJedxHNo 3aKpenJIeHbI.