Precissiongyro 5000 Infinity Auto - Washing machine CECOTEC - Free user manual and instructions

USER MANUAL Precissiongyro 5000 Infinity Auto CECOTEC

Safety instruction 12

1. Parts and components 116
2. Before use 116
3. Operation 117
4. Cleaning and maintenance 117
5. Recycling of electrical and electronic equipment 118
6. Copyright 118
7. Declaration of Conformity 118

SOMMAIRE

Read the following instructions carefully before using the appliance. Keep this instruction manual for future reference or new users.

• WARNING: read all safety warnings, instructions, figures and specifications supplied with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
• ⚠vWARNING: read all safety warnings and instructions marked with the symbol ⚠.
• Keep all safety warnings and instructions for future reference.

1) Work area safety

a) Keep the work area clean and well illuminated.
b) Do not operate power tools in explosive environments, such as in the presence of flammable liquids, gases or dust. Power tools create sparks that can light dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can make you lose control of the tool.

2) Electrical safety

a) The power tools plugs must match the socket. Never modify the plug. Do not use adapter plugs with earthed power tools. The unmodified plugs and the suitable sockets reduce the risk of electric shock.
b) Avoid body contact with earthed surfaces, such as pipes, radiators, stoves and refrigerators. There is a higher risk of electric shock if your body is in touch with grounded surfaces.
c) Do not expose power tools to rain or wet conditions. The

water inlet in a power tool increases the risk of electric shock.

3) Personal safety

a) Stay alert and use common sense when using a power tool. Do not use power tools if you are tired or under the influence of drugs, alcohol or medication. Lack of attention while operating power tools can result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective gear, like dust mask, non-slip safety footwear, helmet or hearing protection, used under the appropriate conditions, will reduce the risk of injuries.
c) Avoid unintentional start-up. Make sure the switch is in Off position before connecting the tool to a power source and/or battery, or before picking it up or transporting it. Carrying power tools with your finger on the switch or plugging in power tools with the switch in the On position will result in injuries.
d) Remove any spanners or wrenches before switching on the power tool. Leaving a spanner or wrench in a rotary piece of the tool may cause injuries.
e) Do not exert too much force when using the tool. Keep your feet firmly on the ground and maintain your balance at all times. This will provide better control of the electric tool in unexpected situations.
f) Wear appropriate clothes. Do not wear loose clothing or jewellery. Keep hair and clothing away from moving parts. Loose clothing, jewellery or long hair can get caught in moving parts.
g) If adapters are provided for the connection of dust extraction and collection, ensure that they are connected and used correctly. Dust vacuuming can reduce dust-related risks.

ENGLISH

h) The confidence gained from frequent use of tools should not be a reason for ignoring general security principles. A careless action can cause serious injury within a fraction of a second.

4) Use and care of electric tools

a) Do not force the power tool. Use the appropriate power tool for the project. The proper electric tool will make your work better and safer using the speed for which it was designed.

b) Do not use the power tool if the switch does not switch it on and off. Any electric tool that cannot be controlled with a switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories or storing it. These preventive safety measures reduce the risk of the power tool starting up accidentally.

d) Store idle electric tools out of the reach of children and do not allow people unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of inexperienced users.

e) Maintenance of power tools and accessories. Check if the moving parts are misaligned or stuck, if there are broken pieces or any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Cutting tools properly maintained and with sharp cutting edges are less likely to jam and are easier to handle.

g) Use the electric tool, accessories and drill bits, etc. according to these instructions, taking into account work conditions

and the work to be carried out. Use of the power tool for operations other than those intended could result in a hazardous situation.

h) Keep handles and gripping surfaces dry, clean and free of oil and grease. Slippery gripping surfaces do not allow safe handling and control of the tool in unexpected situations.

5) Use and care of the batteries

a) Only rechargewith the chargers specified by the manufacturer. A charger suitable for one type of battery may create a fire hazard if used with another type of battery.
b) Use the power tool only with specifically designated battery packs. Use of any other type of battery may create a risk of injury and fire.
c) When the battery is not in use, keep it away from other metal objects, such as paper clips, coins, keys, nails, screws or other small metal objects, which can establish a connection from one terminal to another. A short circuit between the battery terminals can cause burns or fire.
d) Under harsh conditions, liquid may leak from the battery; avoid touching it. In case of accidental contact, rinse the affected part with water. If the liquid comes into contact with eyes, seek medical assistance immediately. Liquid leaking from the battery may cause skin irritation or burns.
e) Do not use a damaged or modified battery or tool. Damaged or modified batteries can show unpredictable behaviours leading to fire, explosion or risk of injury.
f) Do not expose a battery or tool to fire or excessive temperatures. Exposition to fire and high temperatures over 130\ °C could cause an explosion.
g) Follow all charging instructions and do not charge the battery or the tool outside the temperature range specified

ENGLISH

in the instructions. Improper charging or charging at temperatures outside the specified range may damage the battery and increase the risk of fire.

6) Service

a) Have your power tool serviced by a qualified technician using only identical replacement parts. This ensures that the power tool remains safe.
b) Never repair damaged batteries. Battery maintenance must only be carried out by the manufacturer or authorised technician.

7) Charging safety

• Children aged from 8 years and above and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge can use the charger if they have been given supervision or instruction concerning use of the power tool in a safe way and understand the hazards involved.
• Children must not play with the power tool or the power cable.
• Cleaning and maintenance tasks must not be carried out by unsupervised children.
• The power cable of this charger is not replaceable. Discard the charger if the power cable is damaged.

8) Use and handling of the charger

• Connect the charger only if the voltage of the socket matches the information on the rating plate.

• Connect the charger only to an easily accessible socket so that you can quickly disconnect it from the mains in the event of a malfunction.

• Always allow sufficient ventilation when charging the battery; gases may be released.

• Do not charge non-rechargeable batteries.
• Keep the charger away from humidity.
• Never use the charger in environments where explosive or flammable materials are present. There is a risk of fire and explosion.
• Do not place objects on top of the charger and do not cover it.
• Keep the charger away from heat sources.
• Regularly check the charger for damage.
• Repair damaged chargers properly before reusing them.
• The charger must not be disassembled. Repairs should only be carried out by an authorised technician.
• Do not use the charger if it has been subjected to shocks or falls.
• Always unplug the charger from the power supply after use.
• Unplug the charger from the power supply before cleaning, servicing, storing and transporting, and allow it to cool completely.

9) General precautions

• Hold the electric tool by the insulated gripping surfaces when performing an operation in which the tool may come into contact with exposed wiring. The tool must not come into contact with live wires. This may result in electric shock.
• Keep the power tool and its accessories away from hot surfaces.
• Do not allow untrained people use the power tool and its accessories.
• People with physical or mental disabilities must not use power tools or accessories without supervision.

ENGLISH

• Children must not play with, clean or try to repair the power tool and its accessories.
• Allow the tool to cool down completely after use before touching it.
• Always wait until all moving parts have stopped after working with the tool.

Symbol	Meaning
	Warning
	Warning, flammable material
	Information
	For indoor use only
	Class II tool
	Polarity of output terminals
	DC voltage
	Refer to the instruction manual/brochure
	Wear protective gloves
	Wear eye protection

INSTRUCTIONS DE SÉCURITÉ

The graphics in this manual are schematic representations and may not exactly match the product.

2. BEFORE USE

• This appliance comes in a packaging designed to protect it during transport. Remove the appliance from its box. You can keep the original box and other packaging materials in a safe place to prevent damage to the appliance if you need to transport it in the future. If you wish to dispose of the original packaging, make sure all items are recycled properly.
• Check that all parts and components are included and in good condition. If any of them are missing or damaged, please contact Cecotec's Official Technical Support Service immediately.

Box content:

• Electric precision screwdriver
• CRV bits
• Repair accessories
• Fold-out case
• Built-in magnetiser in case
• Instruction manual

Do not remove the product's serial number in order to keep proper traceability if technical assistance is required.

3. OPERATION

LED light operation:

Press and hold the main button to turn on the LED light. This feature is useful for illuminating the work area in low-light conditions.

Speed selection:

Briefly press the main button to switch between different speeds. The display will show the current status of the screwdriver, indicating the selected speed.

Speed	Noise level	RPM	Motor torque
1	Approx. 65 dB	80 RPM	Approx. 0.05 N·m
2	Approx. 70 dB	100 RPM	Approx. 0.15 N·m
3	Approx. 75 dB	130 RPM	Approx. 0.25 N·m
4	Approx. 80 dB	160 RPM	Approx. 0.45 N·m
Manual	-	-	Approx. 0.45 N·m

Rotation direction:

Use the direction button to rotate the screwdriver clockwise.

Use the opposite button to rotate anticlockwise.

Battery status:

The display also shows the battery charge level. Recharge the screwdriver when the battery indicator is low to ensure optimal performance.

4. CLEANING AND MAINTENANCE

Before cleaning the screwdriver, ensure it is switched off and disconnected from any power source.

External cleaning:

Use a soft, dry cloth to clean the external surface of the screwdriver. Avoid using harsh chemicals that may damage the device's finish.

ENGLISH

Display:

Clean the display with a slightly damp microfibre cloth. Do not apply excessive pressure to avoid damaging the display.

Buttons:

Check the buttons to ensure there is no accumulation of dust or dirt. You may use a small, dry brush to clean around the buttons.

Storage:

After cleaning, store the screwdriver in a dry, secure place, away from direct sunlight or extreme temperatures.

5. RECYCLING OF ELECTRICAL AND ELECTRONIC EQUIPMENT

This symbol indicates that, according to the applicable regulations, the product and/or battery must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the batteries/accumulators and take them to a collection point designated by the local authorities. For detailed information on how to properly dispose of electrical and electronic equipment and/or the corresponding batteries, consumers should contact their local authorities.

Compliance with the above guidelines will help protecting the environment.

6. COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The content of this publication may not, either in part or in its entirety, be reproduced, stored in a retrieval system, transmitted or distributed by any means (electronic, mechanical, photocopying, recording or similar) without prior authorisation from CECOTEC INNOVACIONES, S.L.

7. DECLARATION OF CONFORMITY

MANUFACTURER: CECOTEC INNOVACIONES S.L

ADDRESS: Av. Reyes Católicos, No. 60, 46910, Alfafar, Valencia (Spain).

DESCRIPTION: Cordless portable tool

PRODUCT IDENTIFICATION: PrecisionGyro 5000 Infinity Auto

FUNCTION: Multi-bit screwdriver with LED light

MODEL: A01_EU01_115176

It certifies that the product described has been designed, manufactured and tested and complies with all applicable requirements.

EU DIRECTIVES IMPLEMENTED:

• Directive 2006/42/CE on machinery.
• Directive 2014/30/EU on the harmonisation of the laws of the Member States relating to electromagnetic compatibility.
• Directive 2011/65/EU and delegated directive (EU) 2015/863 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

APPLICABLE HARMONISED NORMS:

• EN 62841-1:2015 +A11:2022
• EN 62841-2-2:2014
• EN IEC 55014-1:2021
• EN IEC 55014-2:2021
• EN IEC 61000-3-2:2019/A1:2021
• EN 61000-3-3:2013/A2:2021
• IEC 62321-3-1:2013; IEC 62321-4:2013+A1:2017; IEC 62321-5:2013; IEC 62321-6:2015; IEC 62321-7-1:2015; IEC 62321-7-2:2017; IEC 62321-8:2017

FRANÇAIS

1. PIÈCES ET COMPOSANTS

Img. 1

7. DÉCLARATION DE CONFORMITÉ

ي revisions widened her own moment.