D05FS - Pressure regulator HONEYWELL - Free user manual and instructions

Brand	HONEYWELL
Model	D05FS
Product type	Pressure regulator (reducing valve)
Authorized fluids	Water, oil-free compressed air, nitrogen
Maximum upstream pressure	25 bar
Downstream pressure (model A)	1.5 - 6 bar (preset to 3 bar)
Downstream pressure (models E / EF)	1.5 - 5.5 bar (preset to 3 bar)
Max. operating temperature	70 °C
Minimum pressure drop	1 bar
Connection sizes	1/2" - 2"
Delivery contents	Housing with G 1/4" pressure gauge connection, threaded and female connections, valve trim with diaphragm and seat, spring cap with adjusting knob, adjustment spring
Housing material	Dezincification-resistant brass
Diaphragm material	Textile-reinforced NBR
Seal material	NBR
Pressure gauge connection	G 1/4"
Installation	Horizontal, spring cap upward
Maintenance	Filter cleaning, annual downstream pressure check, professional maintenance every 1 to 3 years
Spare parts	Complete assembly, valve core, filter element, plug, pressure gauge, hexagonal key, connection sets
Standards	DIN EN 1567 (models E/EF), PED directive

Frequently Asked Questions - D05FS HONEYWELL

What is the default downstream pressure?

The downstream pressure is preset to 3 bar for all models.

How to adjust the outlet pressure?

Close the inlet isolation valve, depressurize the outlet, close the outlet valve, loosen the slotted screw, turn the adjusting knob to the left until stop, slowly open the inlet valve, then turn the knob to the desired value. Retighten the screw and slowly open the outlet valve.

What is the maximum upstream pressure?

The maximum upstream pressure is 25 bar.

Which fluids can be used?

Water, oil-free compressed air, and nitrogen, in accordance with applicable standards.

How to clean the filter?

Close the inlet valve, depressurize the outlet, close the outlet valve, release the spring tension, unscrew the cap, remove the ring, take out the valve trim assembly, remove the filter, clean it, then reassemble in reverse order.

How often should maintenance be performed?

Check the downstream pressure once a year. A complete maintenance should be performed every 1 to 3 years by a professional.

What to do if water comes out through the spring cap?

This indicates a defective diaphragm. The valve trim assembly must be replaced.

How to calibrate the adjustment scale after disassembly?

Install a pressure gauge, close the inlet valve, depressurize, close the outlet valve, loosen the slotted screw, slowly open the inlet valve, set the pressure (e.g. 4 bar), align the scale with the mark, retighten the screw, open the outlet valve.

What is the maximum operating temperature?

The maximum operating temperature is 70 °C.

What materials are used?

Housing in dezincification-resistant brass, diaphragm in textile-reinforced NBR, seals in NBR, spring in spring steel, cap and knob in high-quality plastic.

USER MANUAL D05FS HONEYWELL

Keep instructions for later use!

Pressure reducing valve

Disconnecteur

Drukreduceerklep

1. Follow the installation instructions.
2. Use the appliance
   according to its intended use
3. in good condition
   with due regard to safety and risk of danger.
4. Note that the appliance is exclusively for use in the applications detailed in these installation instructions. Any other use will not be considered to comply with requirements and would invalidate the warranty.
5. Please take note that any assembly, commissioning, servicing and adjustment work may only be carried out by authorized persons.
6. Immediately rectify any malfunctions which may influence safety.

2. Application

Medium	Water, compressed air* and nitrogen* in consideration of valid standards (e.g. DIN EN 12502)
Inlet pressure	max. 25 bar
Outlet pressure
D05FS-... A	1,5-6 bar (preset to 3 bar)
D05FS-... E
D05FS-...EF	1,5-5,5 bar (proven to NF EN 1567 and preset to 3 bar)

*As part of an installation being approved according to PED requirements, this product must also be certified.

3. Technical data

Operating temperature	max. 70°C
Minimum pressure drop	1 bar
Connection size	1/2" - 2"

4. Scope of delivery

The pressure reducing valve comprises:

• Housing with pressure gauge connection G1/4"
• With internal and external threads 12 " - 1"
• With external threads 1 1/4" - 2"
• Valve insert complete with diaphragm and valve seat
• Spring bonnet with adjustment knob and setting scale
• Adjustment spring
• Pressure gauge not included (see accessories)

5. Assembly

5.1 Installations Guidelines

It is necessary during installation to follow the installation instructions, to comply with local requirements and to follow the codes of good practice.

Install in horizontal pipework with spring bonnet directed upwards
Installshutoffvalves
- The installation location should be protected against frost and be easily accessible - Pressure gauge can be read off easily - Simplified maintenance and cleaning
- For residential applications where maximum protection against dirt is required, install a fine filter upstream of the pressure reducing valve
- Provide a straight section of pipework of at least five times the nominal valve size after the pressure reducing valve (in accordance with DIN 1988, Part 5)

5.2 Assembly instructions

When using soldering connections, do not solder the connections together with the pressure reducing valve! High temperature will irreparably damage important internal working components!

1. Thoroughly flush pipework
2. Install pressure reducing valve

o Note flow direction

o Install without tension or bending stresses

1. Set outlet pressure

6. Commissioning

6.1 Setting outlet pressure

Set outlet pressure min. 1 bar under inlet pressure.

1. Close shutoff valve on inlet
2. Release pressure on outlet side (e.g. through water tap)
3. Close shutoff valve on outlet
4. Loosen slotted screw

o Do not remove slotted screw

1. Slacken tension in compression spring
   o Turn control handle to the left (-) until it does not move any more
2. Slowly open shutoff valve on inlet
3. Turn control handle until the setting scale shows the desired value
4. Retighten slotted screw
5. Slowly open shutoff valve on outlet

7. Maintenance

We recommend a planned maintenance contract with an installation company In accordance with DIN 1988, part 8, the following measures must be taken:

7.1 Inspection

7.1.1 Pressure reducing valve

Interval: once a year

1. Close shut off valve on outlet
2. Check back pressure using a pressure meter when there is zero through-flow o If the pressure is increasing slowly, the valve may be dirty or defective. In this instance, carry out servicing and cleaning
3. Slowly open shutoff valve on outlet

7.2 Maintenance

Frequency: every 1-3 years (depending on local operating conditions)
To be carried out by an installation company

1. Close shutoff valve on inlet
2. Release pressure on outlet side (e.g. through water tap)
3. Close shutoff valve on outlet
4. Loosen slotted screw o Do not remove slotted screw
5. Slacken tension in compression spring o Turn control handle to the left (-) until it does not move any more
6. Unscrew spring bonnet o Use double ring wrench ZR06K
7. Remove slip ring
8. Remove valve insert with a pair of pliers
9. Remove filter and clean
10. Check that sealing ring, edge of nozzle and slotted ring are in good condition, and if necessary replace the entire valve insert
11. Reassemble in reverse order
    Press in diaphragm with finger before inserting slip ring
12. Adjust setting scale and set outlet pressure

7.3 Adjusting the setting scale

If the adjustment knob is removed, this setting is lost. A new setting can be achieved using a pressure gauge.

1. Close shutoff valve on inlet

2. Release pressure on outlet side (e.g. through water tap)

3. Close shutoff valve on outlet
4. Fit manometer
5. Loosen slotted screw o Do not remove slotted screw
6. Slowly open shutoff valve on inlet
7. Set desired outlet pressure (e.g. 4 bar)
8. Align scale (e.g. 4) in middle of viewing window
9. Retighten slotted screw
10. Slowly open shutoff valve on outlet

7.4 Cleaning

Caution!

Do not use any cleaning agents containing solvents and/or alcohol to clean the plastic parts!

If nesseccary, the filter can be cleaned.

To be carried out by an installation company or the operator.

Detergents must not be allowed to enter the environment or the sewerage system!

1. Close shutoff valve on inlet
2. Release pressure on outlet side (e.g. through water tap)
3. Close shutoff valve on outlet
4. Slacken tension in compression spring o Turn control handle to the left (-) until it does not move any more
5. Unscrew spring bonnet o Use double ring wrench ZR06K
6. Remove slip ring
7. Remove valve insert with a pair of pliers
8. Remove filter, clean and reinsert
9. Reassemble in reverse order

Press in diaphragm with finger before inserting slip ring

1. Adjust setting scale and set outlet pressure

8. Disposal

• Dezincification resistant brass housing
• High-quality synthetic material valve insert
• High-quality synthetic material spring bonnet with adjustment knob and setting scale
  Spring steel adjustment spring
• Fibre-reinforced NBR diaphragm
  NBR seals

Observe the local requirements regarding correct waste recycling/disposal!

1. Troubleshooting

VST06-B Connection set

Problem	Cause	Remedy
Beating sounds	Pressure reducing valve is too large	Call our Technical Customer Services
Water is escaping from the spring bonnet	Diaphragm in valve insert is faulty	Replace valve insert
Too little or no water pressure1109	Shutoff valves up- or downstream of the pressure reducing valve are not fully open	Open the shutoff valves fully
	Pressure reducing valve is not set to the desired outlet pressure	Set outlet pressure
	Filter in pressure reducing valve is contaminated	Clean or replace filter
	Pressure reducing valve is not fitted in flow direction	Fit pressure reducing valve in flow direction (note direction of arrow on housing)
The outlet pressure set does not remain constant	Filter in pressure reducing valve is contaminated or worn	Clean or replace filter
	Valve insert, sealing ring or edge of nozzle is contaminated or worn	Replace valve insert
	Rising pressure on outlet (e.g. in boiler)	Check check valve, safety group etc.

1. Spare Parts

Pressure Reducing Valve D05FS, from 2007 onwards

No.Description Dimension Part No.

1 Spring bonnet 1 / 2^ - 1^ 0901515 complete with 114'' - 2'' 0903890 setting scale
2 Valve insert 1/2" - 1" D05FA-1/2B complete (without 114'' - 2'' D05FA-11/4B filter)
3 Replacement filter 1 / 2^ - 2^ ESD05FS insert
4 Blanking plug with 1 / 2'' - 2'' S06K-1/4 O-ring R1/4" (5 pcs.)

1. Accessories

M38K Pressure gauge Housing diameter 50~mm below connection thread G1/4". Ranges: 0 - 4, 0 - 10, 0 - 16 or 0 - 25 bar. Please indicate upper value of pressure range when ordering

ZR06K Double ring wrench

For removal of spring bonnet

VST06-A Connection set

Threaded connections

Solder connections

Automation and Control Solutions

Honeywell GmbH

Hardhofweg

D-74821 Mosbach

Phone: [phone]

Fax: [phone]

http://europe.hbc.honeywell.com

www.honeywell.com

Manufactured for and on behalf of the

Environmental and Combustion Controls Division of

16, Switzerland by its Authorised Representative Honeywell GmbH

MU1H-1034GE23 R1109

Subject to change