AG-3628 - Cordless blower DOLMAR - Free user manual and instructions

Product type	Cordless blower
Brand	DOLMAR
Model	AG-3628
Rated voltage	36 V DC
Air volume (high speed)	4,4 m³/min
Air volume (low speed)	2,6 m³/min
No-load speed (high)	17 000 min⁻¹
No-load speed (low)	10 000 min⁻¹
Length without nozzle	436 mm
Length with nozzle	921 mm
Net weight	3,1 kg
Sound pressure level	81,2 dB(A)
Sound power level	93,9 dB(A)
Guaranteed sound power level	96,0 dB(A)
Vibration emission	≤ 2,5 m/s²
Battery type	Lithium-ion
Number of speeds	2 (high/low)
Automatic stop	Yes, battery protection
Included accessories	Long nozzle, shoulder strap
Recommended use	Dust blowing
Routine maintenance	Cleaning with damp cloth, carbon brush replacement
Spare parts	Carbon brushes, battery, charger, nozzle, shoulder strap
Repairability	Dolmar approved service center
Compliance standards	CE, EN15503

Frequently Asked Questions - AG-3628 DOLMAR

How to change the speed of the appliance?

Press the HIGH/LOW button to toggle between high and low speed. The first press activates high speed, the second low speed, and so on.

How to install the battery?

Align the battery tab with the groove in the housing, then slide it in until it clicks. Make sure the red part of the button is no longer visible.

How to remove the battery?

Slide the button on the front of the battery while pulling it out of the tool.

How to clean the appliance?

Use a cloth soaked in soapy water. Never use gasoline, benzene, thinner, or alcohol.

When to replace the carbon brushes?

Check the carbon brushes regularly. Replace them when they are worn down to the wear limit line. Both carbon brushes must be replaced at the same time.

Can I use the appliance in the rain?

No. Do not expose the appliance to rain. Use on a wet surface may cause electric shock.

What is the noise level of the appliance?

The sound pressure level is 81,2 dB(A) and the sound power level is 93,9 dB(A). Wear hearing protection.

What accessories are available?

Recommended accessories are the long nozzle, shoulder strap, and authentic Dolmar batteries and chargers.

How to use the shoulder strap?

Pull the shoulder strap hook to extend it, then thread the shoulder strap through the hook. Adjust the length before use.

What to do if the appliance stops during use?

This may be due to overload or low battery. Press the OFF button, eliminate the cause, then restart with HIGH/LOW. If it persists, recharge the battery.

USER MANUAL AG-3628 DOLMAR

The followings show the symbols used for the equipment. Be sure that you understand their meaning before use.

Symboles

Explanation of general view

1 Red part

5 “OFF” button

9 Hanger

2 Button

6 Hook

10 Limit mark

3 Battery cartridge

7 Button

11 Screwdriver

4 HIGH/LOW button

8 Long nozzle

12 Brush holder cap

SPECIFICATIONS

Model

AG-3628

Capacities

Air volume (HIGH) 4.4 m³/min.

Air volume (LOW) 2.6 m³/min.

No load speed (^-1)

HIGH. 17,000

LOW. 10,000

Overall length

(without long nozzle) 436 mm

(with long nozzle) 921 mm

Net weight. 3,1 kg

Rated voltage D.C. 36 V

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Intended use

The tool is intended for blowing dust.

ENB116-4

BLOWER SAFETY WARNINGS

1. Always use protective goggles, a cap and mask when using the blower.
2. Never point the nozzle at anyone in the vicinity when using the blower.
3. Warning - Electric shock could occur if used on wet surfaces. Do not expose to rain. Store indoors.

4. Never block suction inlet and/or blower outlet.

5. Do not block suction inlet or blower outlet to clean up in dusty areas.

6. Do not use the blower with a tapered nozzle smaller than the original one, such as a new nozzle obtained by attaching an extra diameter-reduced hose or smaller hose to the nozzle top end.
7. Do not use the blower to inflate balls rubber boat or the similar.

Increased motor revolution may cause dangerous fan breakage and result in serious personal injury.

Heated motor and control circuit may cause a fire.

1. Keep children, other bystanders and pets away from the blower while operating.

2. Do not operate the blower near open window, etc.

3. Operating the blower only at reasonable hours is recommended - not early in the morning or late at night when people might be disturbed.
4. Using rakes and brooms to loosen debris before blowing is recommended.
5. It is recommended to slightly dampen surfaces in dusty conditions or use mister attachment available on the market.
6. It is recommended to use the long nozzle so the air stream can work close to the ground.
7. The blower is not intended for use by young children or infirm persons without supervision.
8. Young children should be supervised to ensure that they do not play with the blower.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.
4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.

A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

1. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50^ (122^) .
2. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
3. Be careful not to drop or strike battery.
4. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely discharged.
   Always stop tool operation and charge the battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 10^ - 40^ (50^ - 104^) . Let a hot battery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before installing or removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge.
• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

Battery protection system

The battery cartridge is equipped with the protection system, which automatically cuts off the output power for its long service life.

The tool may stop during operation when the tool and/or battery are placed under the following situation. This is caused by the activation of protection system and does not show the tool trouble.

• When the tool is overloaded:

At this time, press the "OFF" button and remove causes of overload and then press the "HIGH/LOW" button again to restart. When the tool does not work even after pressing the "HIGH/LOW" button, the battery power auto-stop is still at work. Charge the battery cartridge before use.

• When the remaining battery capacity becomes low: Recharge the battery cartridge.

Switch action (Fig. 2)

To start the tool, simply press the "HIGH/LOW" button. To switch off, press the "OFF" button. To change the tool speed, press the "HIGH/LOW" button. The first press on this button is for high speed and the second press for low speed and then each press on this button repeats the high/low speed cycle alternatively.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

Installing or removing the long nozzle (Fig. 3 & 4)

To install the long nozzle, push in onto the blower outlet of the tool all the way.

To remove the long nozzle, press its both buttons and with the buttons being pressed pull it out.

Installing the shoulder strap (Fig. 5)

Pull the hanger out of the tool.

Hook the shoulder strap onto the hanger of the tool.

Before use, adjust the length of strap so that it is easy to work with it.

OPERATION

Blowing (Fig. 6)

Hold the blower firmly with a hand and perform the blowing operation by moving it around slowly.

When blowing around a building, a big stone or a vehicle, direct the nozzle away from them.

When performing an operation in corner, start from the corner and then move to wide area.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.

Cleaning (Fig. 7)

From time to time, wipe off the outside of the tool using a cloth dampened in soapy water.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 8 & 9)

Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps.

Take out the worn carbon brushes, insert the new ones and secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Dolmar Authorized Service Centers, always using Dolmar replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended for use with your Dolmar tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

If you need any assistance for more details regarding these accessories, ask your local Dolmar service center.

• Long nozzle
  Shoulder strap
• Various type of Dolmar genuine batteries and chargers
• Battery adaptor

Descriptif

1 Partie rouge

Nominate spanning. DC 36 V

For European countries only

EC Declaration of Conformity

The undersigned, Tamiro Kishima and Rainer Bergfeld, as authorized by Dolmar GmbH, declare that the DOLMAR machine(s):

Designation of Machine: Cordless Blower

Model No./ Type: AG-3628

Specifications: see "SPECIFICATIONS" table.

are of series production and

Conforms to the following European Directives: 2000/14/EC, 2006/42/EC

And are manufactured in accordance with the following standards or standardized documents: EN15503

The technical documentation is on file at:

Dolmar GmbH,

The conformity assessment procedure required by Directive 2000/14/EC was in Accordance with annex V.

Measured Sound Power Level: 92.4 dB

Guaranteed Sound Power Level: 96.0 dB

12.11.2009

Tamiro Kishima
Managing Director

Rainer Bergfeld
Managing Director

FRANÇAIS

Tamiro Kishima
Director General

Rainer Bergfeld
Director General

PORTUGUES

2000/14/EC, 2006/42/EC

E está fabricadas de acordo com as següntes normas ou documents normativos:

EN15503

Móvo yia xwpe ts Eupwnns

△λωσ Σμμορφωσκ EK

Oi KAtwBIOuoyEvapMevo,Tamiro Kishima KAI Rainer Bergfeld, EouoiDotouEvov ano T dolmar GmbH, nnwovou ot to/ta xvavna(ta) DOLMAR:

Xapaktnpiouc mnxavmaotc: Duonmpac mnatapiac Ap. muvtelou/Tunoc: AG-3628

PpOdiaypaΦεc: βλ. πivaka "TEXNIKA

XAPAKTHPIIETIKA".

2000/14/EK, 2006/42/EK

kai kataaekuaovta ouwva u ta akoloutheta npotuna n eyypapa tunonoinans:

EN15503

To apxio tsexviknc tekunpiowc pfuaoetau 0tn dieuovon:

Dolmar GmbH,

The typical A-weighted noise level determined according to EN15503:

Sound pressure level (L_DA) : 81.2 dB (A)

Sound power level (L_WA) : 93.9 dB (A)

Uncertainty (K): 2.5 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined according to EN15503:

Work mode: operation without load

Vibration emission (a_h) : 2.5m / s^2 or less

Uncertainty (K): 1.5m / s^2

ENG901-1

• The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.
• The declared vibration emission value may also be used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

FRANÇAIS

ENG102-3

Bruit