DJ020 - Radio LEXIBOOK - Free user manual and instructions

USER MANUAL DJ020 LEXIBOOK

1. Optical viewfinder
2. Camera lens
   3.Shutter/Set button
3. Power/Mode button
4. Playback mode button
   6.Up button
5. Down button
6. Battery compartment
7. LCD display
8. USB connector port
9. Strap hole
10. Tripod hole (tripod not included)

INSERTING NEW BATTERIES

1. Make sure the camera is off.
2. Slide open the battery door in the direction of the arrow.
3. Insert 2 x LR03/AAA 1,5V type batteries = = = (not included) observing the polarity indicated inside the battery compartment.
4. Close the battery compartment.

Non-rechargeable batteries are not to be recharged. Rechargeable batteries are to be removed from the product before being charged. Rechargeable batteries are only to be charged under adult supervision. Different types of batteries or new and used batteries are not to be mixed. Only batteries of the same or equivalent type as recommended are to be used. Batteries are to be inserted with the correct polarity. Exhausted batteries are to be removed from the product. The supply terminals are not to be short circuited. Do not throw batteries into a fire. Remove the batteries if you are not going to use the product for a long period of time.

WARNING: Mal-function or loss of memory may be caused by strong frequency interference or electrostatic discharge. Should any abnormal function occur, remove the batteries and insert them again.

Important note: all the files stored into the unit's internal memory will be lost when replacing the batteries. Make sure you transfer the files to your computer before changing the batteries.

INSTALLING THE SOFTWARE AND THE CAMERA DRIVER

Follow these instructions to install the "Photo Impression" software and the camera driver on your computer system.

1. Insert the CD Software (included) in your CD-ROM drive. The CD will auto run, and the installation menu will appear.
2. Click "Install Driver", and then follow the instructions to install the camera driver.
3. You will need to reboot your computer after the driver installation.
4. Click "Photo Impression" and follow the instructions to install "Photo Impression". The "Photo Impression" software offers many applications for photo editing and printing.
5. You will need to reboot your computer after the software installation. Once the installation is completed, the "913D Camera" folder will be automatically created on your desktop.

Note :

• If the CD does not auto run, click "Start", "Run", then type in "D:\autorun.exe" in the Run dialog text box (where D:\ is your CD-ROM drive) and press Enter.
• You must install the driver before downloading pictures from the camera or using it as a webcam.
• Make sure the camera is not connected to your computer before installing the driver and the software.

TURNING THE CAMERA ON AND OFF

1. Press the Power/Mode button (4) to turn the camera on. The camera will make a beep sound to confirm that it is ready for use.
2. Press and hold the Power/Mode button (4) for a few seconds again to turn it off.

Note: The camera will auto power off after 60 seconds of inactivity.

TAKING PHOTOS

Single shooting

You are already in "Single shooting" mode when you switch on the camera. Press the Shutter button (3) to take a photo. The camera will beep to confirm that a picture is taken. The number of pictures that you can take in memory is shown on the LCD screen.

Continuous shooting

1. When you are in "Single shooting" mode, press the Power/Mode button (4) once to get in "Continuous shooting" mode.
2. The "Continuous shooting" mode will be displayed in the upper-right corner of the screen. Press the Shutter button (3) within the next 3 seconds to take 3 pictures continuously.

Note: When the camera's built-in memory is full, you will not be able to take any pictures.

PLAYBACK MODE

1. Switch on the unit then press the Playback mode (5) button.
2. Use the Up (6) and the Down (7) buttons to display the next or the previous photo.
3. To exit the playback mode, press the Playback mode (5) at any time.

Note: If there are no pictures stored in the camera's built-in memory, the playback mode is not available.

Deleting one file in playback mode

In playback mode, use the Up (6) and the Down (7) buttons to display the desired photo then the Shutter button (3) twice to delete it.

DELETING PHOTOS

Deleting the last photo taken

Turn on the unit then press repeatedly the Power/Mode button (4) until the D icon is displayed on the screen. Within 3 seconds, press the Shutter button (3) to delete the last photo taken.

Note: to cancel the deletion, wait for the D icon to disappear from the screen or press the Up (6) or the Down (7) buttons.

Deleting all photos

Turn on the unit then press repeatedly the Power/Mode button (4) until the F icon is displayed on the screen. Within 3 seconds, press the Shutter button (3) to delete all the photos stored in the camera's built-in memory.

Note: to cancel the deletion, wait for the F icon to disappear from the screen or press the Up (6) or the Down (7) buttons.

SELF-TIMER

1. In "Single shooting" mode, press repeatedly the Power/Mode button (4) until the "Self-timer" icon appears in the upper-right corner of the LCD screen. Then press the Shutter button (3) within 3 seconds to turn on the self-timer function.
2. The digital camera will take a picture 10 seconds later.

Note: The self-timer feature is automatically turned off after the picture has been taken.

SELECTING THE PHOTO RESOLUTION

In "Single shooting" mode, press repeatedly the Power/Mode button (4) until one of the resolution icons or is displayed on the screen. Then press the Shutter button (3) within 3 seconds to change the resolution. Wait a few seconds to confirm your choice; the unit will automatically go back to photo mode.

There are 2 resolution modes:

High resolution (640x480 pixels, default mode).

Low resolution (320x240 pixels).

SELECTING THE IMAGE QUALITY

In "Single shooting" mode, press repeatedly the Power/Mode button (4) until one of the image quality icons or is displayed on the screen. Then press the Shutter button (3) within 3 seconds to change the image quality. Wait a few seconds to confirm your choice; the unit will automatically go back to photo mode.

There are 2 levels of quality:

High quality (default mode).

Low quality.

SELECTING THE LIGHT SOURCE FREQUENCY

In "Single shooting" mode, press repeatedly the Power/Mode button (4) until one of the frequency icons 50 or 60 is displayed on the screen. Then press the Shutter button (3) within 3 seconds to change the frequency. Wait a few seconds to confirm your choice; the unit will automatically go back to photo mode.

DOWNSLOADING YOUR PHOTOS AND YOUR VIDEOS

1. Turn on the camera, then connect it to your computer via the USB cable provided.
2. Open the "913D Camera" folder on your desktop, then double-click the "913D Camera" icon to open the photo download window.
3. You can edit your pictures (contrast, brightness..etc.) using the "Photo Editing" button
4. Click the "Photo download" button top display the images stored in your camera as thumbnails.
5. Select the pictures you want to download individually or click the "Select all" button to select all the photos automatically.
6. Click the "Save" button to transfer the files to the desired folder.

WEBCAM MODE

Connected to your PC, your camera can be used as a webcam.

Webcam mode

1. Connect the video camera to your computer using the USB cable provided.
2. Open the "913D Camera" folder on the desktop, then double-click the "PCCam"

icon _cam . The PC icon will appear on the LCD screen of your digital camera to indicate that you are in webcam mode.
3. If you can't see any image, click "Options" in the "PCCam" window then make sure that the "Preview" option is ticked in the drop-down list. If the problem persists, click "Devices" then check that the "913D Camera" and "Realtek AC97 Audio" options are selected.

Instant messaging (chat)

You can use your camera as a webcam with your instant messaging client (Yahoo Messenger, MSN Messenger, Skype...).

Ex: using MSN Messenger

1. Put your camera in webcam mode and connect it to your computer then launch MSN Messenger.
2. On the MSN interface, select "Actions", then "Start a Video Conversation".
3. Select the person you want to chat with, and press "OK".

MAINTENANCE

Only use a soft, slightly damp cloth to clean the unit. Do not use detergent. Do not expose the unit to direct sunlight or any other heat source. Do not immerse the unit in water. Do not dismantle or drop the unit. Do not try to twist or bend the unit.

WARRANTY

NOTE: Please keep this instruction manual, it contains important information. This product is covered by our 1-year warranty. To make use of the warranty or the after-sales service, please contact your retailer and supply proof of purchase. Our warranty covers material or installation-related defects attributable to the manufacturer, with the exception of wear caused by failure to respect the instructions for use or any unauthorised work on the equipment (such as dismantling, exposure to heat or damp, etc).

Reference: DJ020series

Designed in Europe - Made in China

©2010 Lexibook®

United Kingdom & Ireland

For any further information, please call Helpline: 0808 1003015

http://www.lexibook.com

C E

This product is not a toy.

Environmental Protection

Unwanted electrical appliances can be recycled and should not be discarded along with regular household waste! Please actively support the conservation of resources and help protect the environment by returning this appliance to a collection centre (if available).

CONOZCA SU CAMARA

Instant Messaging (Chat)

What is your overall impression of the product? (Your answer will be published later.)

What is your overall impression? Very satisfactory/Très satisfaisant!

Disappointing/Decevant