DJ200BB - Radio LEXIBOOK - Free user manual and instructions

USER MANUAL DJ200BB LEXIBOOK

Please refer to images A & B located at the back of the cover page.

1. Power button 2. MODE button 3. Delete button 4. Up arrow key
2. Down arrow key 6. LED 7. Shutter button 8. LCD display
3. USB socket

INSERTING NEW BATTERIES

Please refer to image C located at the back of the cover page.

1. Turn the camera off.
2. Open the battery compartment by sliding the cover off.
3. Note the polarity of the batteries (+/- signs) inside of the battery compartment.
4. Insert 3 new AA batteries. Replace and close the battery cover by sliding it into place.

Warning: If the unit malfunctions or receives an electrostatic shock, remove the battery and insert it again.

Battery level

The following icons on the LCD screen indicate the batteries' level of power:

Full

Medium

Low

When the low battery icon keeps flashing, please replace the batteries.

Important note: all files on the unit's SDRAM memory will be lost when replacing the batteries. Make sure you transfer the files to your PC before changing the batteries.

INSTALLING AN OPTIONAL MEMORY CARD

Your Barbie Digital Camera has a built-in SDRAM memory of 32MB. You may also insert an SD card (not included) to increase the memory size of the camera. To do so, push the SD card firmly into the slot until you hear a "click" sound. Please refer to image D located at the back of the cover page.

The icon will be displayed after inserting an SD card and powering the unit on.

INSTALLING THE CAMERA DRIVER AND SOFTWARE

Follow these instructions to install the camera driver and application software on your PC system.

1. Insert the CD Software (included) in your CD-ROM drive. The CD will auto run, and the installation menu will appear. Click on "Install Driver", and then follow the instructions to install it. You will need to reboot your computer after the driver installation.
   Note: If the CD does not auto run, click Start Run, type in "D:" autorun.exe" in the Run dialog text box (where D:\ is your CD-ROM drive).
2. Proceed similarly to install the Photolmpression and Videolmpression software. These software offer many photo and video applications.

Notes:

• You must install the driver before downloading files from the camera.
• Do not connect the video camera to your PC during the software installation.
• You can click on "Browse CD" to read the user guides of the PhotoImpression and Videolpression software. If you cannot read the files, you will have to install Acrobat Reader first.

TURNING THE CAMERA ON AND OFF

3.

ory

intil

ck of

ing

n

）

Press the Power button [1] for 3 seconds to turn the video camera ON.

Press and hold the Power button [1] for three seconds to turn the

camera OFF.

Note: The camera will auto power off after 60 seconds of inactivity.

SHOOTINGVIDEOCLIPS

1. Turn the video camera ON; and make sure it is set to video shooting
   mode. The icon is displayed in the upper left corner of the screen.
2. Hold the video camera firmly and lift the LCD screen [8] open.
3. Press the Shutter button [7] to start shooting. The duration of the
   video clip is displayed on the lower right corner of the LCD screen.
4. Press the Shutter button [7] again to stop shooting.

TAKING PHOTOS

ROM

deo

1. Turn the video camera ON. Press MODE once to enter photo taking
   mode. The icon 2 is displayed in the upper left corner of the screen.
   Otherwise, press the MODE key until the icon is displayed.
2. Hold the video camera firmly and lift the LCD screen [8] open.
3. Press the Shutter button [7] to take a photo.

PLAYBACK MODE

era.

0-

iles,

1. Turn the video camera ON. Press MODE twice to enter playback
   mode. The icon is displayed in the upper left corner of the screen.
2. The number of video clips/pictures taken is indicated on the lower
   left side of the screen.

3. Press the up arrow key [4] to view the previous photo or video.
   Press the down arrow key [5] to view the next photo or video.

4. The icon located on the bottom right part of the screen indicates that the file is a video clip.

Press the Shutter button [7] to play the selected video clip. Press the Shutter button [7] again to stop the playback.

DELETING FILES

Deleting one file

In playback mode, select a file and press the DEL button [3]. When "Delete picture?" appears onscreen, press the DEL button within 5 seconds to confirm. The selected photo/video clip will be deleted.

Deleting all files

In playback mode, press and hold the DEL button [3] for about 6 seconds. When "Delete all?" appears onscreen, press DEL [3] within 5 seconds to confirm. All photos/video clips will be deleted.

Note: if you press the DEL button by mistake, just wait 5 seconds to cancel this operation or press the up or down arrow keys.

FORMATING THE SD CARD

Do not format your SD card unless you wish to delete all its data or if it has not been formatted.

1. Set up your digital video camera under DV (digital video) or DSC (photographic camera) mode.
2. Press the DEL button [3]. "Format card?" is displayed onscreen.
3. Press the DEL button [3] within 5 seconds to confirm. Your card will be formatted.

Note: wait 5 seconds to cancel this operation or press the up or down arrow keys.

ites

1e

MASS STORAGE MODE

1. Turn the digital video camera off.
2. Lift the USB connector cover. Plug the smaller connector of the USB cable into the USB port on the camera. Plug the larger connector of the USB cable to the USB port on your PC or notebook computer.
3. The icon will be displayed onscreen to indicate that the digital camera is in Mass Storage mode.
4. Double-click My Computer /Removable Disk/DCIM/100JLCAM.
5. You can now copy the files to other drives of your PC.

PC CAM MODE

in 5

Entering PC Cam mode

1. Turn the digital video camera off.
2. Press and hold the Shutter button [7], and connect the camera to your computer using the USB cable provided.
3. Do not release the Shutter button [7] until the icon appears on the LCD screen. You are now in PC Cam mode. To view the real-time images taken by the webcam, go to "My Computer" and double click on the new drive called "Digital Camera".

1ta

Video Conference

1. Set your digital video camera to PC Cam mode.
2. Run the video conference software Microsoft NetMeeting on your computer.
3. Input the IP address of the computer you wish to dial in the address bar.
4. Select tool/accept/transfer options. When the other parties have accepted your call, you can now hold a video conference.

MSN Chat

1. Make sure the digital video camera is OFF.
2. Press and hold the Power/Shutter button [7]. Plug the USB jack into the USB port of your PC.
3. Sign in MSN.
4. Connect the digital video camera to your computer using the USB cable.
5. On the MSN interface, select Action/Start a video conversation.
6. Select the person you want to chat with, and press OK.

WARRANTY

NOTE: Please keep this instruction manual, it contains important information. This product is covered by our two-year warranty. To make use of the warranty or the after-sales service, please contact your retailer and supply proof of purchase. Our warranty covers material or installation-related defects attributable to the manufacturer, with the exception of wear caused by failure to respect the instructions for use or any unauthorised work on the equipment (such as dismantling, exposure to heat or damp, etc.).

LEXIBOOK UK Ltd, Unit 10 Petersfield Industrial Estate, Bedford Road,
Petersfield, Hampshire, GU32 3QA, United Kingdom, Freephone
helpline: 0808 100 3015,
http://www.lexibook.com

Environmental Protection

Unwanted electrical appliances can be recycled and should not be discarded along with regular household waste! Please actively support the conservation of resources and help protect the environment by returning this appliance to a collection centre (if available).

CONOCE TU CÁMARA

into

B

take

or ng,

ad,

©2007 Mattel, Inc. ©2007 Lexibook®

ek

an

C E

Milieubescherming