IDS 18V-200 T Professional - Screwdriver BOSCH - Free user manual and instructions

Product Type	Cordless Screwdriver
Brand	Bosch
Model	IDS 18V-200 T Professional
Battery Voltage	18 V
Battery Type	Lithium-Ion
Battery Capacity	4.0 Ah (typical)
Number of Speeds	2
No-Load Speed (1st gear)	0 – 500 rpm
No-Load Speed (2nd gear)	0 – 1,900 rpm
Max Torque (hard screwdriving)	200 Nm
Max Torque (soft screwdriving)	45 Nm
Chuck	Keyless Chuck 13 mm
Max. Screw Diameter	10 mm
Weight (with battery)	1.8 kg
Dimensions (L x W x H)	204 x 78 x 260 mm
Sound Pressure Level	86 dB(A)
Sound Power Level	97 dB(A)
Vibration (drilling in metal)	< 2.5 m/s²
Power Supply	18 V Battery (Bosch Professional system)
Main Functions	Screwing and drilling, forward/reverse, variable speed, spindle lock
Maintenance and Cleaning	Clean with a dry cloth, avoid solvents
Safety	Motor brake, overload protection
Spare Parts and Repairability	Available via Bosch after-sales service
General Information	Professional use, compatible with Bosch 18V system

Frequently Asked Questions - IDS 18V-200 T Professional BOSCH

What is the voltage of the Bosch IDS 18V-200 T Professional screwdriver?

The voltage of the screwdriver is 18 V, compatible with the Bosch Professional 18V system.

What is the maximum torque of this tool?

The maximum torque is 200 Nm in hard screwdriving.

What speeds are available?

The tool has 2 speeds: 0-500 rpm (1st) and 0-1900 rpm (2nd).

What type of chuck is used?

The chuck is a 13 mm keyless chuck.

Is the screwdriver delivered with a battery?

Generally, the tool is sold bare (without battery or charger). Check the package contents.

How to clean the screwdriver?

Clean the device with a dry cloth. Do not use solvents or harsh products.

Can I use batteries from other brands?

No, only use Bosch Professional 18V batteries to ensure safety and performance.

What is the weight of the screwdriver with battery?

The weight is approximately 1.8 kg with a 4.0 Ah battery.

How to change the rotation direction?

Use the forward/reverse switch located above the trigger.

Where to find spare parts?

Spare parts are available from Bosch after-sales service or authorized dealers.

USER MANUAL IDS 18V-200 T Professional BOSCH

(12)

4

German

Safety instructions

www.bosch-pt.com/serviceaddresses

Transport

General Power Tool Safety Warnings

WARNING

Read all safety warnings, instructions, illustrations and specifications.

tions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents. ▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. ▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents. ▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. ▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

Battery pack may create a risk of fire when used with another battery pack.

Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury. Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130 °C may cause explosion. Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Safety Warnings for Impact Wrenches

Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Use suitable detectors to determine if there are hidden supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to explosion. Breaking water pipes causes property damage. Only use impact-resistant bits and sockets as application tools. Only these application tools are suitable for impact screwdrivers. Hold the power tool securely. When tightening and loosening screws be prepared for temporarily high torque reactions. Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.

▶ Always wait until the power tool has come to a complete stop before placing it down. The application tool can jam and cause you to lose control of the power tool. In case of damage and improper use of the battery, vapours may be emitted. The battery can set alight or explode. Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system. ▶ Do not modify or open the battery. There is a risk of short-circuiting. The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat. ▶ Only use the battery in the manufacturer's products. This is the only way in which you can protect the battery against dangerous overload.

Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water and moisture. There is a risk of explosion and short-circuiting.

▶ Application tools can become hot during operation. There is a risk of burns when changing the application tool. Use protective gloves to remove the application tool.

Symbols

The following symbols may be important for the operation of your power tool. Please take note of these symbols and their meaning. Correctly interpreting the symbols will help you to operate the power tool more effectively and safely.

Symbols and their meaning

Tool data logging is enabled in this tool.

Wireless connectivity power tool with built-in NFC technology

The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the USA and in other countries.

Product Description and Specifications

Read all the safety and general instructions.

Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.

Please observe the illustrations at the beginning of this operating manual.

Intended Use

The machine is intended for driving in and loosening screws and bolts as well as for tightening and loosening nuts within the respective range of dimension.

Product Features

The numbering of the product features refers to the diagram of the power tool on the graphics page.

(1) Tool holder (2) Rubber ring (tool holder) (3) Mount for holder (4) Rotational direction switch (5) Thread for belt clip (6) Rechargeable battery a) (7) Battery release button 4 (8) User interface (9) Position of the built-in NFC antenna (10) On/off switch (11) Worklight (12) Handle (insulated gripping surface) (13) Application tool (e.g. socket spanner) a) (14) Tightening status indicator (15) Holder a)

a) This accessory is not part of the standard scope of delivery.

User interface

(16) Temperature alarm indicator (17) Battery status indicator (18) Maintenance indicator (19) "User interface locked" indicator (20) Indicator for "soft screwdriving" mode (21) Button for torque preselection 2 (22) Display for torque preselection (23) Button for torque preselection 1

Technical Data

Cordless Impact Screw-driver		IDS 18V-200 T
Article number		3 601 JN0 0..
Rated voltage V= 18
No-load speed A)B)	min -1	0–2500
Impact rate A)B)	min -1	0–3500
Max. tightening torque B)C)	Nm 300
Max. loosening torque B)C)	Nm 450
Number of settings in "Automatic switch-off" mode (user interface)		9 (settings 1–9)

18 | English

Cordless Impact Screw-driver		IDS 18V-200 T
Number of settings without "Automatic switch-off" mode (user interface)		1 (setting "H")
Machine screw diameter in "Automatic switch-off" mode	mm M8-M14
Max. screw diameter without "Automatic switch-off" mode	mm M18
Tool holder 1/2"
Weight B)	kg 1.6-2.7
Recommended ambient temperature during charging	°C 0 to +35
Permitted ambient temperature during operation and during storage	°C -20 to +50
Recommended rechargeable batteries		GBA 18V...ProCORE18V...
Recommended battery chargers		GAL 18...GAX 18...GAL 36...

A) Measured at 20–25 °C with rechargeable battery ProCORE18V 4.0Ah B) Depends on battery in use C) Measured at 3 seconds, screw size M20 Values can vary depending on the product, scope of application and environmental conditions. To find out more, visit www.bosch-professional.com/wac.

Noise/vibration information

Noise emission values determined according to EN 62841-2-2.

Typically, the A-weighted noise level of the power tool is: Sound pressure level 101 dB(A); sound power level 109 dB(A). Uncertainty K = 3 dB.

Wear hearing protection!

Vibration total values a_n (triax vector sum) and uncertainty K determined according to EN 62841-2-2:

Tightening screws and nuts of the maximum permitted size: a_h < 11.6 m/s^2, K = 1.5 m/s^2

The vibration level and noise emission value given in these instructions have been measured in accordance with a standardized measuring procedure and may be used to compare power tools. They may also be used for a preliminary estimation of vibration and noise emissions.

The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different accessories or is poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total working period.

To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions over the total working period.

Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and accessories, keeping their hands warm, and organizing workflows correctly.

Rechargeable battery

Bosch sells some cordless power tools without a rechargeable battery. You can tell whether a rechargeable battery is included with the power tool by looking at the packaging.

Charging the battery

▶ Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.

Note: Lithium-ion rechargeable batteries are supplied partially charged according to international transport regulations. To ensure full rechargeable battery capacity, fully charge the rechargeable battery before using your tool for the first time.

Inserting the Battery

Push the charged battery into the battery holder until it clicks into place.

Removing the Battery

To remove the rechargeable battery, press the battery release button and pull the battery out. Do not use force to do this.

The rechargeable battery has two locking levels to prevent the battery from falling out if the battery release button is pressed unintentionally. The rechargeable battery is held in place by a spring when fitted in the power tool.

Battery charge indicator

Note: Not all battery types have a battery charge indicator.

The green LEDs on the battery charge indicator indicate the state of charge of the battery. For safety reasons, it is only possible to check the state of charge when the power tool is not in operation.

Press the button for the battery charge indicator or to show the state of charge. This is also possible when the battery is removed.

If no LED lights up after pressing the button for the battery charge indicator, then the battery is defective and must be replaced.

Battery model GBA 18V...

LED Capacity

3× continuous green light 60–100 %

2× continuous green light 30–60 %

LED Capacity

1× continuous green light 5–30%

1× flashing green light 0–5 %

Battery model ProCORE18V...

LED Capacity

5 × continuous green light 80–100 %

4 × continuous green light 60–80 %

3 × continuous green light 40–60 %

2 × continuous green light 20–40 %

1 × continuous green light 5–20 %

1 × flashing green light 0–5 %

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Only store the battery within a temperature range of -20 to 50 °C. Do not leave the battery in your car in the summer, for example.

Occasionally clean the ventilation slots on the battery using a soft brush that is clean and dry.

A significantly reduced operating time after charging indicates that the battery has deteriorated and must be replaced. Follow the instructions on correct disposal.

Assembly

▶ Before carrying out any work on the power tool (e.g. maintenance, tool change etc.), remove the battery from the power tool. There is risk of injury from unintentionally pressing the on/off switch.

Changing the tool (see figure A)

When fitting an application tool, make sure that it is held securely in the tool holder. If the application tool is not held securely in the tool holder, it may become loose and consequently uncontrollable.

Slide the application tool (13) onto the square drive of the tool holder (1) as far as it will go on the rubber ring (tool holder) (2).

Note: The rubber ring (tool holder) (2) rotates when the power tool is operated with the tool holder (1). Therefore, keep a small distance between the rubber ring (tool holder) (2) and the gearbox housing of the power tool.

Belt clip

The belt clip is not included with the product as standard. You can find the complete selection of accessories in the Bosch accessories range.

You can use the belt clip to hang the power tool on a belt, for example. You then have both hands free and the power tool is always within easy reach.

Holder (see figure E)

To attach the holder (15) to the power tool, secure both ends of the holder to the corresponding mount (3).

Operation

Only apply the power tool to the screw/nut when the tool is switched off. Rotating tool inserts can slip off.

Operating Principle

The tool holder (1) (with the application tool) is driven by an electric motor via a gear and impact mechanism.

The working procedure is divided into two phases:

Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed connection runs tight and load is therefore put on the motor. The impact mechanism then converts the power of the motor to steady rotary impacts. When loosening screws or nuts, the process is reversed.

Set the rotational direction (see figure C)

The rotational direction switch (4) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (10) is being pressed.

Right rotation: To drive in screws and tighten nuts, press the rotational direction switch (4) through to the left stop.

Left Rotation: To loosen and unscrew screws and nuts, press the rotational direction switch (4) through to the right stop.

Adjusting the Speed/Impact Rate

You can adjust the speed/impact rate of the power tool when it is on by pressing in the on/off switch (10) to varying extents.

Applying light pressure to the on/off switch (10) results in a low rotational speed/impact rate. Applying increasing pressure to the switch increases the speed/impact rate.

Switching on/off

To start the power tool, press and hold the on/off switch (10).

The worklight (11) lights up when the on/off switch (10) is lightly or fully pressed, allowing the work area to be illuminated in poor lighting conditions.

To switch off the power tool, release the on/off switch (10).

LED worklight with status indicator

The LED worklight (11) is also used as a status indicator for device protection:

LED Feedback

Description

Flashing light 3x during downtime Device protection is active. Device protection has been activated to prevent the battery from consuming a large amount of power and to protect the device against damage.

User Interface (see figure B)

The user interface is used for torque preselection and to preselect working mode, as well as to indicate the status of the power tool.

Display (user interface) Description Meaning

-	8	+
TORQUE	TORQUE

-	8	+
TORQUE	TORQUE

-	8	+
TORQUE	TORQUE

-	8	+
TORQUE	TORQUE

-	8	+
TORQUE	TORQUE

No display lights up on the user interface (8).

The power tool and the user interface (8) are switched off.

The selected setting for torque preselection is shown on the display for torque preselection (22).

The indicator for "soft screwdriving" mode (20) lights up white. The selected setting for torque preselection is shown on the display for torque preselection (22).

The letter "H" appears on the display for torque preselection (22).

The "User interface locked" indicator (19) lights up white.

"Soft screwdriving" mode (20) is switched on (see "Selecting the working mode", page 22).

"Automatic switch-off" mode is switched off. (see "Selecting the working mode", page 22)

The user interface (8) is locked. The buttons for torque preselection 1 and 2 ((23)/(21)) are locked. The torque cannot be changed.

You have 2 options for unlocking the user interface:

- Via the BeConnected app/PRO360 - By resetting the user interface (8) to factory settings, if the smartphone or app is currently unavailable to you. Hold down the buttons for torque preselection 1 ((23)) or the button for torque preselection 2 ((21)) for 6 seconds. You can then reapply the settings via the user interface (8).

Display (user interface) Description Meaning

-

8

+

-	2	+
TORQUE	TORQUE

-	8	+
TORQUE	TORQUE

-	8	+
TORQUE	TORQUE

Preselecting the Torque

You can select the required torque in 9 stages using the buttons for torque preselection 1 and 2 ((23)/(21)). The power

The maintenance indicator (18) lights up orange.

The battery status indicator (17) lights up orange.

The battery status indicator (17) lights up red.

The temperature alarm indicator (16) lights up red.

Scheduled maintenance is due.

Send the power tool to customer service (see "After-Sales Service and Application Service", page 24) for maintenance.

The battery in the power tool will soon be empty and will soon need to be replaced or recharged.

In addition to the display on the user interface (8), the status indicator screw-driving process (14) lights up red and an audio signal sounds.

An insufficiently charged battery will impair the torque of the power tool. Recharge the battery or replace it with a fully charged battery.

The battery in the power tool is empty and needs to be replaced or recharged.

- The power tool has overheated. Allow the power tool to cool down before you carry on working.

- The power tool or rechargeable battery is charged wirelessly. Allow the power tool or rechargeable battery to charge fully before you carry on working.

The tool stops automatically when the set torque is reached.

A tightening status indicator (14) and an audible alarm signal will indicate the status of the screwdriving process (see table and figure D below).

Screwdriving process status indicator Audible alarm signal Meaning

Green – The screwdriving process is proceeding		without any problems.The torque is the same as the selected torque preselection setting.
Red Audio signal (1 second) A fault has occurred during the screwdriv-		ing process.Possible causes:- The on/off switch was released too soon- The battery in the power tool is nearly empty (see "User Interface (see figure B)", page 20)- The power tool detects a sudden load change

Screwdriving process status indicator	Audible alarm signal Meaning
		- The overload protection on the power tool is active
Orange Audio signal (1 second) A fault has occurred during the screwdriv-		ing process.Possible causes:- The power tool is running at no load- The power tool does not detect an impact

Torque preselection in 9 stages

The diagram displayed describes the individual stages with the associated torque and the corresponding machine screw (see figure F).

The torque values in the diagram have been measured under standardized measuring conditions and are for reference only. The actual torque may be influenced by various factors. To increase the torque, press the button for torque preselection 1 (+) (23). To decrease the torque, press the button for torque preselection 2 (-) (21). The corresponding torque preselection setting is shown in digits on the torque preselection display (22).

Selecting the working mode

The power tool has 2 working modes.

Switching on "Automatic switch-off" mode (settings 1-9)

"Automatic switch-off" mode is used for pre-tightening or tightening screws to prevent the screws from being tightened too tightly or too loosely. In "Automatic switch-off" mode, you can preselect a specific torque (see figure F).

You can switch on "Automatic switch-off" mode as follows:

- "Automatic switch-off" mode is preset on the power tool.

- If the display for torque preselection (22) shows the letter "H", press the button for torque preselection 1 (+) (23).

Setting 1 for "Automatic switch-off" mode is selected and is shown on the display for torque preselection (22).

Switching off "Automatic switch-off" mode (setting H)

If "Automatic switch-off" mode is switched off, you cannot preselect a torque. The power tool reaches a maximum torque of 300 Nm.

You can switch off "Automatic switch-off" mode as follows:

- If you are at setting 1, press the button for torque preselection 2 (-) (21).

- If you are at setting 9, press the button for torque preselection 1 (+) (23).

The letter "H" appears on the display for torque preselection (22).

Switching "Soft Screwdriving" Mode On and Off

To switch on "soft screwdriving" mode (20), press the buttons for torque preselection 1 and 2 ((23)/(21)) at the same time.

To switch off "soft screwdriving" mode (20), press the buttons for torque preselection 1 and 2 ((23)/(21)) at the same time again.

Selecting the torque level

Select the torque level as follows:

- Select the appropriate torque using the reference values in the diagram (see figure F).

- Set the correct torque level (1–9). If the power tool has spring lock washers, activate the "soft screwdriving" mode. If the power tool does not have spring lock washers, deactivate the "soft screwdriving" mode.

- Start the screwing process by pressing the on/off switch (10). It is recommended to measure the values with a digital torque spanner.

- For torque values that are 15 % higher than the required torque, it is recommended to select a lower torque level on the power tool using the torque preselection button 2 (21).

- For torque values that are 15% below the required torque, it is recommended to select a higher torque level on the power tool using the torque preselection button 1 (23).

- For torque values within the limits of 15%, the selected torque level can be retained.

Note: It is recommended to carry out the measurements described at least three times in order to obtain consistent results and to be able to save these results in the settings.

Practical advice

The torque depends on the impact duration. The maximum achieved torque results from the sum of all individual torques achieved through impact. Maximum torque is achieved after an impact duration of 6–10 seconds. After this duration, the tightening torque increases only minimally. The impact duration is to be determined for each required tightening torque. The tightening torque actually achieved should always be checked with a torque wrench.

Screw applications with hard, spring-loaded or soft joints When the achieved torques in an impact series are measured during a test and transferred into a diagram, the result is the curve of a torque characteristic. The height of the curve cor-

responds with the maximum reachable torque, and the steepness indicates the duration in which this is achieved.

A torque gradient depends on the following factors:

• Strength properties of the screws/nuts
• Type of backing (washer, disc spring, seal) – Strength properties of the material being screwed/bolted together – Lubrication conditions at the screw/bolt connection

The following application cases result accordingly:

- A hard joint is a metal-to-metal screw application which uses washers. After a relatively short impact duration, the maximum torque is reached (steep characteristic curve).

Unnecessary long impact duration only causes damage to the machine.

• A spring-loaded joint is also a metal-to-metal screw application but uses spring washers, disc springs, studs or screws/nuts with conical joints. It is also called a spring-loaded joint when extensions are used.
• A soft joint is a screw application of e.g. metal on wood or a screw application that uses lead washers or fibre washers as backing.

For a spring-loaded joint as well as for a soft joint, the maximum tightening torque is lower than for a hard joint. Also, a clearly longer impact duration is required.

Guide values for maximum screw tightening torques

Figures given in Nm; calculated from the tensional cross-section; utilisation of the yield point: 90% (with friction coefficient µ_total = 0.12 ). As a control measure, always check the tightening torque with a torque wrench.

Property classes according to DIN 267	Standard screws High-strength screws
	3.6	4.6	5.6	4.8	6.6	5.8	6.8	6.9	8.8	10.9	12.9
M8	6.57	8.7	11	11.6	13.1	14.6	17.5	19.7	23	33	39
M10	13	17.5	22	23	26	29	35	39	47	65	78
M12	22.6	30	37.6	40	45	50	60	67	80	113	135
M14	36	48	60	65	72	79	95	107	130	180	215
M16	55	73	92	98	110	122	147	165	196	275	330
M18	75	101	126	135	151	168	202	227	270	380	450

Tips

Before screwing larger, longer screws into hard materials, it is advisable to pre-drill a pilot hole with the core diameter of the thread to approx. 2/3 of the screw length.

Note: Ensure that no metal particles enter the power tool. After working at a low speed for an extended period, you should operate the power tool at the maximum speed for approximately three minutes without load to cool it down.

Connectivity functions

System Requirements for Using the App

System Requirements

Mobile device (tablet, smartphone)	Android 6.0 (and newer)
	iOS 11 (and newer)

Installing and Setting up the App

You will need to install the device-specific app before you can use the connectivity functions.

- Download the app from the corresponding app store (Apple App Store, Google Play Store). Note: You will need to have a user account with the relevant app store to do this.

App name iOS/Android

BeConnected

PRO360

- The display of your mobile device shows you all of the subsequent steps required to connect the power tool to the mobile device.

Functions in Conjunction with the Power Tool

In conjunction with the NFC module, the following connectivity functions are available for the power tool:

• Registration and personalisation
• Status check, output of warning and error messages – General information and settings
• Management
• Locking the user interface
• Setting the working modes

You can find further information in the Help menu in the app.

Maintenance and Service

Maintenance and Cleaning

Clean the air vents on your power tool regularly. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards. Before carrying out any work on the power tool (e.g. maintenance, tool change etc.), remove the battery from the power tool. There is risk of injury from unintentionally pressing the on/off switch. ▶ To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.

After-Sales Service and Application Service

Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.

In all correspondence and spare parts orders, please always include the 10-digit article number given on the nameplate of the product.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham Uxbridge

UB 9 5HJ

At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.

Tel. Service: [phone]

E-Mail: [e-mail]

You can find further service addresses at:

www.bosch-pt.com/serviceaddresses

Transport

The recommended lithium-ion batteries are subject to legislation on the transport of dangerous goods. The user can transport the batteries by road without further requirements.

When the batteries are shipped by third parties (e.g. air transport or forwarding agency), special requirements on packaging and labelling (e.g. ADR regulations) must be met. A dangerous goods expert must be consulted when preparing the items for shipping.

Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.

Disposal

Power tools, rechargeable batteries, accessories and packaging should be sorted for environmental-friendly recycling.

Do not dispose of power tools and batteries/re-chargeable batteries into household waste!

Only for EU countries:

Power tools that are no longer suitable for use and defective or used batteries must be disposed of separately. Use the designated collection systems.

If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom:

According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Battery packs/batteries:

Li-ion:

Please observe the notes in the section on transport (see "Transport", page 24).

Mobile device (tablet, smartphone)

Robert Bosch (France) S.A.S.

www.bosch-pt.com/serviceaddresses

Transport

Calle Robert Bosch No. 405

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

Bosch Service Center

Telegrafvej 3

2750 Ballerup

Spare parts can be ordered online or a repair order can be created at www.bosch-pt.dk.

Service Center Phone: [phone]

Fax: [phone]

E-Mail: [e-mail]

Further service addresses can be found under:

www.bosch-pt.com/serviceaddresses

Transport

Bosch Service Center

Telegrafvej 3

2750 Ballerup

Denmark

Tel.: [phone] (within Sweden)

Fax: [phone]

Further service addresses can be found under:

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

Robert Bosch Sp. z o.o.

www.bosch-pt.com/serviceaddresses

Transport

Bosch Service Center PT

K Vápence 1621/16

692 01 Mikulov

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Power tool service

Strada Horia Măcelariu Nr. 30–34, sector 1

013937 Bucharest

www.bosch-pt.com/serviceaddresses

Transport

Electric tools service

Strada Horia Măcelariu Nr. 30–34, sector 1

013937 Bucharest, Romania

www.bosch-pt.com/bg/bg/

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

The contained lithium-ion batteries are subject to the requirements of the law on dangerous goods. The user can transport the batteries by road without additional conditions.

When shipping via a third party (e.g., air transport or freight forwarding), special requirements regarding

packaging and labeling must be observed. In this case, a dangerous goods specialist must be consulted when preparing the shipment.

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

Robert Bosch Morocco SARL

www.bosch-pt.com/serviceaddresses

Transport

www.bosch-pt.com/serviceaddresses

Transport

Legal Information and Licenses

BSD-3-Clause

Infineon TLE Library, version 1.2.4

Copyright (c) 2015, Infineon Technologies AG

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of the copyright holders nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Warranty Disclaimer

This product contains Open Source Software components which underly Open Source Software Licenses. Please note that Open Source Licenses contain disclaimer clauses. The text of the Open Source Licenses that apply are included in this manual under "Legal Information and Licenses".

CE

1

de	EU-Konformitätserklärung		Wir erklären in alleiniger Verantwortung, dass die genannten Produkte allen einschlägigen Bestimmungen der nachfolgend aufgeführten Richtlinien und Verordnungen entsprechen und mit folgenden Normen übereinstimmen.Technische Unterlagen bei:*
	Akku-Schlagschrauber	Sachnummer
en	EU Declaration of Conformity		We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards.Technical file at:*
	Cordless Impact Screwdriver	Article number
fr	Déclaration de conformité UE		Nous déclarons sous notre propre responsabilité que les produits décrits sont en conformité avec les directives, règlements normatifs et normes énumérés ci-dessous.Dossier technique auprès de:*
	Visseuse à choc sans fil	N° d'article
es	Declaración de conformidad UE		Declaramos bajo nuestra exclusiva responsabilidad, que los productos nombrados cumplen con todas las disposiciones correspondientes de las Directivas y los Reglamentos mencionados a continuación y están en conformidad con las siguientes normas.Documentos técnicos de:*
	Atornilladora de impacto accionada por acumulador	N° de artículo
pt	Declaração de Conformidade UE		Declaramos sob nossa exclusiva responsabilidade que os produtos mencionados cumprem todas as disposições e os regulamentos indicados e estão em conformidade com as seguintes normas.Documentação técnica pertencente à:*
	Aparafusadora de percussão sem fio	N.° do produto
it	Dichiarazione di conformità UE		Dichiariamo sotto la nostra piena responsabilità che i prodotti indicati sono conformi a tutte le disposizioni pertinenti delle Direttive e dei Regolamenti elencati di seguito, nonché alle seguenti Normative.Documentazione Tecnica presso:*
	Avvitatore a percussione a batteria	Codice prodotto
nl	EU-conformiteitsverklaring		Wij verklaren op eigen verantwoordelijkheid dat de genoemde producten voldoen aan alle desbetreffende bepalingen van de hierna genoemde richtlijnen en verordeningen en overeenstemmen met de volgende normen.Technisch dossier bij:*
	Accuslagmoeraan zetter	Productnummer
da	EU-overensstemmelseserklæring		Vi erklærer som eneansvarlige, at det beskrevne produkt er i overensstemmelse med alle gældende bestemmelser i følgende direktiver og forordninger og opfylder følgende standarder.Tekniske bilag ved:*
	Akku-slagboremaskine	Typenummer
sv	EU-konformitetsförklaring		Vi förklarar under eget ansvar att de nämnda produkterna uppfyller kraven i alla gällande bestämmelser i de nedan angivna direktiven och förordningarnas och att de stämmer överens med följande normer.Teknisk dokumentation:*
	Sladdlös slående skruvdragare	Produktnummer
no	EU-samsvarserklæring		Vi erklærer under eneansvar at de nevnte produktene er i overensstemmelse med alle relevante bestemmelser i direktivene og forordningene nedenfor og med følgende standarder.Teknisk dokumentasjon hos:*
	Akku-slagskrutrekker	Produktnummer
fi	EU-vaatimustenmukaisuusvakuutus		Vakuutamme täten, että mainitut tuotteet vastaavat kaikkia seuraavien direktiivien ja asetusten asiaankuuluvia vaatimuksia ja ovat seuraavien standardien vaatimusten mukaisia.Tekniset asiakirjat saatavana:*
	Akkuiskuruuvinv äännin	Tuotenumero
el	Δήλωση πιστότητος EE		Δηλώνουμε με αποκλειστική μας ευθύνη, ότι τα αναφερόμενα προϊόντα αντιστοιχούν σε όλες τις σχετικές διατάξεις των πιο κάτω αναφερόμενων οδηγιών και κανονισμών και ταυτίζονται με τα ακόλουθα πρότυπα.Tεχνικά έγγραφα στη:*
	Μπουλονόκλειδο μπαταρίας	Αριθμός ευρετηρίου
tr	AB Uygunluk beyani		Tek sorumlu olarak, tanımlanan ürünün aşağıdaki yönetmelik ve direktiflerin geçerli bütün hükümlerine ve aşağıdaki standartlara uygun olduğunu beyan ederiz.Teknik belgelerin bulunduğu yer:*
	Akülü darbeli tork anahtarı	Ürün kodu

||

CE

pl	Deklaracja zgodności UE		Oświadczamy z pełną odpowiedzialnością, że niniejsze produkty odpowiadają wszystkim wymaganiom poniżej wyszczególnionych dyrektyw i rozporządzeń, oraz że są zgodne z następującymi normami.Dokumentacja techniczna:*
	Akumulatorowa wkrętarka udarowa	Numer katalogowy
cs	EU prohlásení oshodě		Prohlašujeme na výhradní zodpovědnost, že uvedený výrobek splňuje všechna příslušná ustanovení níže uvedených směrnic anařízení aje vsouladu snásledujícími normami:Technické podklady u:*
	Akumulátorový rázový šroubovák	Objednací číslo
sk	EÚ vyhlásenie ozhode		Vyhlasujeme na výhradnú zodpovednosť, že uvedený výrobok spíňa všetky príslušné ustanovenia nižšie uvedených smerníc anariadení aje vsúlade snasledujúcimi normami:Technické podklady má spoločnosť:*
	Akumulátorový impulzový skrutkovač	Vecné číslo
hu	EU konformitási nyilatkozat		Egyedüli felelőséggel kijelentjük, hogy a megnevezett termékek megfelelnek az alábbiakban felsorolásra kerülő irányelvek és rendeletek valamennyi idevágó előírásainak és megfelelnek a következő szabványoknak.Műszaki dokumentumok megőrzési pontja:*
	Akkumulátoros ütvecsavarozógé p	Cikkszám
ru	Заявление о соответствии EC		Мы заявляем под нашу единоличную ответственность, что названные продукты соответствуют всем действующим предписаниям нижеуказанных директив и распоряжений, а также нижеуказанных норм.Техническая документация хранится y:*
	Аккумуляторны й шуруповерт ударного действия	Tоварный No
uk	Заява про відповідність ЄС		Мизаявляемо під нашу одноособову відповідальність, що названі вироби відповідають усім чинним положенням нищеозначених директив і розпоряджень, а також нижчеозначеним нормам.Технічна документація зберігається y:*
	Акумуляторний ударний гвинтоверт	Tоварний номер
kk	EO сәйкестік мағлумдамасы		Өз жауапкершілікпен біз аталған өнімдер теменде жзылған директикалар мен жарлықтардың тиісті қағидаларына сәйкестігін және темендері нормаларға сай екенін білдіреміз.Техникалық құжаттар:*
	Аккумуляторлық қәнім нөмірі қағатын бурауыш	Өнім нөмірі
ro	Declaratie de conformitate UE		Declarăm pe proprie răspundere că produsele mentionate corespund tuturor dispozițiilor relevante ale directivelor și reglementărilor enumerate în cele ce urmează și sunt în conformitate cu următoarele standarde.Documentаție tehnică la:*
	Maşină de găurit/ însurubat cu percuție cu acumulator	Număr de identificare
bg	ЕС декларация за съответствие		С пълна отговорност ние декларираме, че посочените продукти отговарят на всички валидни изисквания на директивите и разпоредбите по-долу и съответства на следните стандарти.Техническа документация при:*
	Акумулаторен ударен винтоверт	Каталожен номер
mk	EU-Изјава за сообразност		Со целосна одговорност изјавуваме, дека опишаните производи се во согласност со сите релевантни одредби на следните регулативи и прописи и се во согласност со следните норми.Техничка документација кај:*
	Батериски ударен одвртувач	Број на дел/артикл
sr	EU-izjava o usaglašenosti		Na sopstvenu odgovornost izjavljujemo, da navedeni proizvodi odgovaraju svim dotičnim odredbama naknadno navedenih smernica u uredaba i da su u skladu sa sledećim standardima.Tehnička dokumentacija kod:*
	Uvrtač sa udarcima i akumulatorom	Broj predmeta
sl	Izjava o skladnosti EU		Izjavljamo pod izključno odgovornostjo, da je omenjen izdelek v skladu z vsemi relevantnimi določili direktiv in uredb ter ustreza naslednjim standardom.Tehnična dokumentacija pri:*
	Akumulatorski udarni vijačnik	Številka artikla

CE

III

hr	EU izjava o sukladnosti		Pod punom odgovornošću izjavljujemo da navedeni proizvodi odgovaraju svim relevantnim odredbama direktiva i propisima navedenima u nastavku i da su sukladni sa sljedećim normama.Tehnička dokumentacija se može dobiti kod: *
	Akumulatorski udarni stezač	Kataloški br.
et	EL-vastavusdeklaratsioon		Kinnitame ainuvastutajatena, et nimetatud tooted vastavad järgnevalt loetletud direktiivide ja määruste köikidele asjaomastele nõuetele ja on kooskõlas järgmiste normidega.Tehnilised dokumendid saadaval: *
	Akulöökmutrikee raja	Tootenumber
lv	Deklarácija par atbilstību ES standartiem		Mês ar pilnu atbildību paziņojam, ka šeit aplūkotie izstrādājumi atbilst visiem tālāk minētajās direktīvās un rīkojumos ietvertajām saistošajām nostādnēm,kā arī sekojošiem standartiem.Tehniskā dokumentācija no: *
	Akumulatora triecienskrūvgrie zis	Izstrādājuma numurs
lt	ES atitikties deklaracija		Atsakingai pareiškiame, kad išvardyti gaminiai atitinka visus privalomusžemiau nurodytų direktyvų ir reglamentų reikalavimus ir šiuos standartus.Techninė dokumentacija saugoma: *
	Akumuliatorinis smūginis suktuvas	Gaminio numeris
	IDS 18V-200 T	3 601 JNO 020 2006/42/EC2014/53/EU2011/65/EU	EN 62841-1:2015+A11:2022EN 62841-2-2:2014EN IEC 55014-1:2021EN IEC 55014-2:2021EN 300 330 V2.1.1EN 301 489-3 V2.3.2EN 55032:2015+A11:2020EN 62479:2010EN IEC 63000:2018
			*BOSCH* Robert Bosch Power Tools GmbH(PT/ECS)70538 StuttgartGERMANY
			Thomas DonatoChairman of the Management BoardThousi i.v.kwRobert Bosch Power Tools GmbH, 70538 Stuttgart, GERMANYStuttgart, 12.06.2024

IV

CE

Declaration of Conformity

Cordless Impact Screwdriver Article number

IDS 18V-200 T 3 601 JNO 020

We declare under our sole responsibility that the stated products comply with all applicable provisions of the regulations listed below and are in conformity with the following standards.

Technical file at: Robert Bosch Ltd. (PT/SOP-GB), Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom

The Supply of Machinery (Safety) Regulations 2008

The Radio Equipment Regulations 2017

The Restriction of the Use of Certain Hazardous Substances in

Electrical and Electronic Equipment Regulations 2012

EN 62841-1:2015+A11:2022

EN 62841-2-2:2014

EN IEC 55014-1:2021

EN IEC 55014-2:2021

EN 300 330 V2.1.1

EN 301 489-3 V2.3.2

EN 55032:2015+A11:2020

EN 62479:2010

EN IEC 63000:2018

BOSCH

Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany represented (in terms of the above regulations) by

Robert Bosch Limited, Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom

Vonjy Rajakoba

Managing Director - Bosch UK

Martin Sibley

Business Operations and Aftersales Director

Robert Bosch Ltd. Broadwater Park, North Orbital Road, Uxbridge UB9 5HJ, United Kingdom, as authorised representative acting on behalf of Robert Bosch Power Tools GmbH, 70538 Stuttgart, Germany

Place of issue: Uxbridge Date of issue: 12/06/2024