ER-HGP86 - Beard trimmer PANASONIC - Free user manual and instructions

Find the device manual for free ER-HGP86 PANASONIC in PDF.

PANASONIC ER-HGP86 - Beard trimmer
📄 160 pages English EN Download 💬 AI Question 10 questions ⚙️ Specs
Notice PANASONIC ER-HGP86 - page 4
Pick your language and provide your email: we'll send you a specifically translated version.
Product Type Beard Trimmer
Model ER-HGP86
Brand Panasonic
Dimensions (approx) 18.5 x 4.2 x 3.5 cm
Weight 200 g
Power Source Rechargeable battery (Ni-MH)
Input Voltage 100-240 V AC, 50/60 Hz
Charging Time Approx. 8 hours
Operating Time Approx. 50 minutes
Blade Material Stainless steel
Cutting Length Settings 0.5 mm to 10 mm (with adjustable comb)
Waterproof Yes (IPX7 rating)
Cleaning Method Washable under running water
Maintenance Oil blades regularly (oil included)
Included Accessories Adjustable comb, cleaning brush, oil, charging stand
Warranty 2 years
Repairability Blade unit replaceable; battery serviceable by authorized centers

Frequently Asked Questions - ER-HGP86 PANASONIC

How long does the battery take to fully charge?
The battery takes approximately 8 hours to fully charge.
How long does the trimmer operate on a full charge?
On a full charge, the trimmer operates for about 50 minutes of continuous use.
Can I use the trimmer while it is charging?
No, the ER-HGP86 cannot be used while charging. It must be used cordlessly.
Is the beard trimmer waterproof?
Yes, it is waterproof with an IPX7 rating, so it can be rinsed under running water.
How do I clean the blades?
Remove the blade unit and rinse it under running water. Let it dry completely before reattaching. Apply a drop of oil to the blades after cleaning.
What cutting lengths can I achieve?
With the adjustable comb, you can set cutting lengths from 0.5 mm to 10 mm in 0.5 mm increments.
Can I use the trimmer for body grooming?
Yes, it can be used for beard, mustache, and body grooming. However, for sensitive areas, use appropriate attachments.
How often should I oil the blades?
It is recommended to oil the blades once a week or after every cleaning to maintain performance.
Are replacement blades available?
Yes, replacement blade units are available from Panasonic service centers or authorized retailers.
What should I do if the trimmer stops working?
First, check if the battery is charged. If it still doesn't work, refer to the user manual or contact Panasonic support. Do not disassemble the device yourself.

User questions about ER-HGP86 PANASONIC

0 question about this device. Answer the ones you know or ask your own.

Ask a new question about this device

Your email remains private: it is only used to notify you if someone answers your question.

No questions yet. Be the first to ask one.

Download the instructions for your Beard trimmer in PDF format for free! Find your manual ER-HGP86 - PANASONIC and take your electronic device back in hand. On this page are published all the documents necessary for the use of your device. ER-HGP86 by PANASONIC.

USER MANUAL ER-HGP86 PANASONIC

Operating Instructions

AC/Rechargeable Professional Hair Clipper

Model No. ER-HGP86

Line drawing of a hairbrush with comb and ear (no text or symbols)

English3Svenska57Magyar109
Español13Suomi67Română121
Dansk25Polski77Türkçe133
Português35Česky 89Ελληνικά145
Norsk47Slovensky 99

Panasonic

Operating Instructions

AC/Rechargeable Professional Hair Clipper

Model No. ER-HGP86

Contents

Safety precautions.... 5 Maintenance ....10

Important information ....7 Troubleshooting ....11

Parts identification ....7 Disposal of the appliance ....12

Charging 8 Specifications 12

How to use ......9

Thank you for purchasing this Panasonic product.

Before operating this unit, please read these instructions completely and save them for future use.

WARNING

  • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
  • The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.
  • Do not use anything other than the supplied AC adaptor and the charging stand for any purpose. Also, do not use any other product with the supplied AC adaptor and the charging stand. (See page 8.)
  • Keep the appliance dry.
  • The following symbol indicates that a specific detachable power supply unit is required for connecting the electrical appliance to the supply mains. The type reference of power supply unit is marked near the symbol.

PANASONIC ER-HGP86 - WARNING - 1

Safety precautions

Make sure to follow these instructions.

To prevent accidents, injuries or damage to property, please follow the instructions below.

■ The following chart indicates the degree of damage caused by improper operation.

PANASONIC ER-HGP86 - Safety precautions - 1

DANGER

Indicates potential hazard that will result in serious injury or death.

PANASONIC ER-HGP86 - DANGER - 1

WARNING

Indicates potential hazard that could result in serious injury or death.

PANASONIC ER-HGP86 - WARNING - 1

CAUTION

Indicates a potential hazard that could result in minor injury or property damage.

PANASONIC ER-HGP86 - CAUTION - 1

WARNING

▶ This appliance

  • This appliance has a built-in rechargeable battery. Do not throw into fire or apply heat. Do not charge, use, or leave in a high temperature environment.
  • Doing so may cause overheating, ignition, or explosion.
  • Do not modify or repair.
  • Doing so may cause fire, electric shock, or injury. Contact an authorized service centre for repair (replacement of battery, etc.).
  • Never disassemble except when disposing of the appliance.
  • Doing so may cause fire, electric shock, or injury.

▶ Power supply

  • Do not connect or disconnect the adaptor to a household outlet with a wet hand.
  • Doing so may cause electric shock or injury.
  • Do not immerse the main body, AC adaptor, and charging stand in water or wash them with water.
  • Do not place the main body, AC adaptor, and charging stand over or near a water-filled sink or bathtub.
  • Do not use when the AC adaptor is damaged or when the fitting into the household outlet is loose.
  • Do not damage the cord or the power plug.
  • Do not deface, modify, forcefully bend or pull the cord or the power plug. Also, do not place anything heavy on, twist or pinch the cord.
  • Doing so may cause electric shock or fire due to a short circuit.
  • Do not use in a way exceeding the rating of the household outlet or the wiring.
  • Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating. • Fully insert the adaptor.
  • Failure to do so may cause fire or electric shock.
  • Regularly clean the power plug, the appliance plug and the charging plug to prevent dust from accumulating.

- Failure to do so may cause fire due to insulation failure caused by humidity.

▶ Preventing accidents

  • Do not place within reach of children or infants. Do not let them use it.
  • Putting parts or accessories in the mouth may cause an accident or injury.

WARNING

- If the lubrication oil is consumed accidentally, do not induce vomiting, drink a large amount of water, and contact a physician.

- If the lubrication oil comes into contact with eyes, immediately wash thoroughly with running water, and contact a physician.

- Failure to do so may result in physical problems.

▶ In case of an abnormality or malfunction

- Immediately stop using and remove the adaptor if there is an abnormality or malfunction.

- Failure to do so may cause fire, electric shock, or injury.

- The main body, charging stand or AC adaptor is deformed or abnormally hot.

- The main body, charging stand or AC adaptor smells of burning.

- There is an abnormal sound during use or charging of the main body.

- Immediately request inspection or repair to an authorized service centre.

CAUTION

▶ Protecting the skin

- Do not press the blade strongly against the skin.

- Do not use the appliance for any purpose other than trimming hair and beards.

- Do not directly apply the blades on ears or rough skin (such as swellings, injuries or blemishes).

- Doing so may cause injury to skin or ears.

- Check that the blades are not damaged or deformed before use.

- Failure to do so may cause skin injury.

▶ Note the following precautions

- Do not allow metal objects or trash to adhere to the power plug, the appliance plug or the charging plug.

- Doing so may cause electric shock or fire due to a short circuit.

- Disconnect the adaptor from the household outlet when not using.

- Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.

Handling of the removed battery when disposing

! DANGER

- The rechargeable battery is exclusively for use with this appliance. Do not use the battery with other appliances.

- Do not charge the battery after it has been removed from the appliance.

- Do not throw into fire or apply heat.

- Do not hit, disassemble, modify, or puncture with a nail.

- Do not let the positive and negative terminals of the battery get in contact with each other through metallic objects.

- Do not carry or store the battery together with metallic jewellery such as necklaces and hairpins.

- Do not use or leave the battery where it will be exposed to high temperatures, such as under direct sunlight or near other sources of heat.

- Never peel off the tube.

- Doing so may cause overheating, ignition, or explosion.

WARNING

• After removing the rechargeable battery, do not keep it within reach of children and infants.

- The battery will harm the body if accidentally swallowed. If this happens, consult a physician immediately.

PANASONIC ER-HGP86 - WARNING - 1

WARNING

- If the battery fluid leaks out and comes in contact with the eyes, do not rub the eyes, and thoroughly rinse with clean water, such as tap water.

- Failure to do so may cause eye injury.

Consult a physician immediately.

PANASONIC ER-HGP86 - WARNING - 1

CAUTION

- If the battery fluid leaks out and comes in contact with the skin or clothes, rinse off with clean water, such as tap water.

- Failure to do so may cause inflammation.

Important information

PANASONIC ER-HGP86 - Important information - 1

The symbol on the left means "Do not wash the product with water".

  • This appliance is designed for professional use to trim hair and beards. It can be operated on either an AC adaptor or rechargeable battery.
  • Apply the lubrication oil to the blade before and after each use. (See page 11.)

Failure to apply the lubrication oil may cause the following problems.

  • The appliance has become blunt.
  • Shorter operating time.

Louder sound.

  • The appliance may become warm during operation and/or charging. This is normal.
  • Do not use any blade other than the one dedicated as it may cause defect in performance.
  • You should not allow permanent wave lotion, hair dye or hair spray to come into contact with the main body or the blade. Doing so may result in cracking or corrosion.
  • Before using an attachment, check that it has been installed correctly. Failure to do so may cause hair to be cut too short.
  • Charge the appliance correctly according to these Operating Instructions. (See page 8 "Charging".)
  • This appliance contains a battery that is only replaceable by skilled persons. Please contact an authorized service centre for repair details.

Parts identification

ALabeled diagram of a hairbrush with numbered parts for identification

BPANASONIC ER-HGP86 - Parts identification - 2

EPANASONIC ER-HGP86 - Parts identification - 3

HPANASONIC ER-HGP86 - Parts identification - 4

©PANASONIC ER-HGP86 - Parts identification - 5

FPANASONIC ER-HGP86 - Parts identification - 6

GPANASONIC ER-HGP86 - Parts identification - 7

1PANASONIC ER-HGP86 - Parts identification - 8

PANASONIC ER-HGP86 - Parts identification - 9

KPANASONIC ER-HGP86 - Parts identification - 10

LPANASONIC ER-HGP86 - Parts identification - 11

⑤ Charge status lamp (Red) ⑥ Appliance socket

B Blade © Comb attachment shelves D 1.5 mm comb attachment for fading (1.5 mm - 2.7 mm)

E 3 mm/4 mm comb attachment

F 6 mm/9 mm comb attachment

G 12 mm/15 mm comb attachment

H Charging stand (RC9-92)

⑦ Charging plug

⑧ Stand socket

① AC adaptor (RE9-82)

⑨ Adaptor

⑩ Power plug

⑪ Cord

⑫ Appliance plug

Accessories

J Cleaning brush

K Lubrication oil

L Pouch

Charging

- Turn the appliance off.

1. Connect the appliance plug to the stand socket.

2. Place the appliance on the charging stand.

3. Insert the adaptor into a household outlet.

- Check the charge status lamp (▶) allows.

It turns off after charging is completed.

- Charging is completed after approx. 1 hour.

Diagram of a hairdryer with labeled parts and directional arrows indicating process flow

4. Disconnect the power plug after charging is completed. (For safety and energy saving)

- Charging is required when the recharge lamp blinks.

• The appliance can be used for approximately 5 minutes after the recharge lamp blinks.

PANASONIC ER-HGP86 - Charging - 2

Insert the main body again after removing it from the charging stand. If the charge status lamp glows and then turns off after 5 seconds, charging is completed.

Notes

  • Recommended ambient temperature for charging is 10°C - 35°C. It may take longer to charge, or the charge status lamp will blink quickly and the battery may fail to charge properly in extremely high or low temperatures.
  • 1 full charge will provide approximately 50 minutes of continuous operation. (Based on dry using at 20°C - 30°C) The operating time may differ depending on the frequency of use and the operating method.
  • When charging the appliance for the first time or when it has not been in use for more than 6 months, the charging time may change or the charge status lamp (→) may not glow for a few minutes. It will eventually glow if kept connected.
  • If there is noise from the radio or other sources while using or charging the appliance, move to a different location to use the appliance.
  • Charging each time does not affect battery life, because it uses a lithium-ion battery.
  • The battery will deteriorate if not used for over 6 months, so make sure to perform a full charge at least once every 6 months. • To keep charging the battery will not affect battery performance.

Charging without the charging stand

Plug the AC adaptor into the main body and the household outlet.

PANASONIC ER-HGP86 - Charging without the charging stand - 1

AC operation

If you connect the AC adaptor to the appliance in the same way as for charging, and turn on the power, you can use it.

- If the remaining battery is too low, the blades may move slowly or stop, even with the AC operation. In this case, charge the battery for 1 minute or more.

- The battery will be discharged, even with the AC operation.

How to use

  • Check that the blades are not damaged or deformed before use.
  • Turn the appliance off.
  • Apply the lubrication oil to the blade before and after each use. (See page 11.)
  • The appliance may not operate in an ambient temperature lower than approximately 5 °C.

1 Set the trimming height.

2Turn on the power.

Do not forcefully press the main body on skin because it may cause injury or scratch the skin when holding main body up side down for edge cutting the sideburns or nape.

PANASONIC ER-HGP86 - How to use - 1

Setting the trimming height

For a trimming height of 0.3 mm to 1.5 mm, turn the dial to the desired height.

Use an attachment for a trimming height higher than 1.5 mm or more.

Trimming height indicator: 0.3, 0.6, 0.9, 1.2, 1.5

▶ How to use the 1.5 mm comb attachment for fading

- Adjustable from 1.5 to 2.7 mm, in five 0.3 mm steps, with the 1.5 mm comb attachment for fading.

graph LR A["Indication"] --> B["Trimming height"] A --> C["0.3"] A --> D["0.6"] A --> E["0.9"] A --> F["1.2"] A --> G["1.5"] B --> H["1.5"] B --> I["1.8"] B --> J["2.1"] B --> K["2.4"] B --> L["2.7"]

• The comb attachment for fading is for this appliance only.

Removing and mounting the comb attachments

▶ Mounting the attachment

  1. Select the trimming heights indicated on the insides and sides of the attachments.
  2. Set the dial to "0.3" and then mount the attachment to the main body as illustrated.

▶ Removing the attachment

Slide one side of the attachment off the mounting in the direction indicated with the arrow.

0.3

Illustration of a medical procedure showing a catheter insertion into a tube (no text or symbols present)

Maintenance

• Make sure that the main body is turned off. Clean the main body, blade, and comb attachment after each use. (If not cleaned, the motion will become poor and the sharpness will worsen.) • Lubricate after cleaning. Do not use thinner, benzine, alcohol, or other chemicals. Doing so may cause failure, cracking, or discoloration of the parts. Clean the main body only with a soft cloth slightly dampened with tap water or soapy tap water. * Parts other than blades

How to clean

▶ Main body / Blade

  1. Brush off any hairs from the main body and from around the blade.
  2. Brush off the hairs from the blade edge.
  3. Brush any hair trimmings out from between the stationary blade and the moving blade while pressing down the cleaning lever (a) to raise the moving blade.

PANASONIC ER-HGP86 - ▶ Main body / Blade - 1

PANASONIC ER-HGP86 - ▶ Main body / Blade - 2

Diagram of a mechanical component with a labeled section (a), showing internal parts and a tool inserted (no text or symbols present)

▶ Charging stand

Use the cleaning brush to clean hair trimmings and dust in the charging plug or in the hole on the bottom surface.

PANASONIC ER-HGP86 - ▶ Charging stand - 1

PANASONIC ER-HGP86 - ▶ Charging stand - 2

Removing and mounting the blade

• The blade for fading is for this appliance only.

▶ Remove

Hold the main body with the switch facing upward and push the blade with your thumb while catching the blade in your other hand.

Illustration of a hand holding a small object with an arrow indicating motion, and a magnified inset showing the interior detail (no text or symbols)

▶ Mount

  1. Set the dial to "1.5".

PANASONIC ER-HGP86 - ▶ Mount - 1

  1. Fit the mounting hook (a) into the blade mounting (b) on the main body and push in until it clicks.

Diagram illustrating a mechanical or biological process with labeled parts (a, b) and magnified views showing internal components and final detail.

Replacement parts

Replacement parts are available at your dealer or Service Centre.

Replacement parts for ER-HGP86Blade WER9930
Lubrication oil WES003P
  • Using other than recommended genuine blade, any warranty claim will expire. • We recommend Panasonic lubrication oil WES003P.

Lubrication

- Apply the lubrication oil to the blade before and after each use.

1 Remove the blade. (See page 10.) 2 Apply a drop of the lubrication oil to each indicated point. 3 Attach the blade to the main body, turn on the power and allow to run for approximately 5 seconds.

Cross-sectional diagram of a vehicle head and dashboard with no visible text or symbols

Troubleshooting

Problem Action

The appliance has become blunt.

Operating time is short.

Appliance stopped functioning.

The appliance cannot be charged.

Makes a loud sound.

Until problems are solved, please follow each procedure as follows;

  1. Charge the appliance. (See page 8.)
  2. Clean the blade and apply lubrication oil. (See pages 10 and 11.)
  3. Replace the blade. (See pages 10 and 11.)
  4. Have the battery replaced by an authorized service centre.

Push the main body into the charging stand or appliance plug all the way. Charge within the recommended charging temperature of 10 °C to 35 °C. ▶ Apply lubrication oil. (See this page.) ▶ Confirm that the blade is properly attached.

If the problems still cannot be solved, contact your dealer or a service centre authorized by Panasonic for repair.

Disposal of the appliance

Remove the built-in rechargeable battery before disposing of the appliance.

• The battery is to be disposed of safely. - This figure must only be used when disposing the appliance, and must not be used to repair it. If you dismantle the appliance yourself, it may cause malfunction.

How to remove the battery

  • Remove the appliance from the AC adaptor.
  • Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.
  • Perform following steps and lift the battery, and then remove it.
  • Take care not to short circuit the positive and negative terminals of the removed battery, and insulate the terminals by applying tape to them.

Exploded view diagram of a mechanical device with numbered components for identification

For environmental protection and recycling of materials This appliance contains a Lithium-ion battery. Please make sure that the battery is disposed of at an officially assigned location, if there is one in your country.

Specifications

Power sourceSee the name plate on the AC adaptor. (Automatic voltage conversion)
Motor voltage3.6 V---
Charging time Approx. 1 hour

For more information about the energy efficiency of the product, please visit our website, www.panasonic.com, and enter the model number in the search box.

Disposal of Old Equipment and Batteries

Only for European Union and countries with recycling systems

PANASONIC ER-HGP86 - Disposal of Old Equipment and Batteries - 1

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and batteries, please take them to applicable collection points in accordance with your national legislation.

By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local authority.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

PANASONIC ER-HGP86 - Disposal of Old Equipment and Batteries - 2

Note for the battery symbol (bottom symbol)

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

Panasonic

©PANASONIC ER-HGP86 - Panasonic - 1

PANASONIC ER-HGP86 - Panasonic - 2

KPANASONIC ER-HGP86 - Panasonic - 3

EPANASONIC ER-HGP86 - Panasonic - 4

FPANASONIC ER-HGP86 - Panasonic - 5

GPANASONIC ER-HGP86 - Panasonic - 6

HPANASONIC ER-HGP86 - Panasonic - 7

LPANASONIC ER-HGP86 - Panasonic - 8

1PANASONIC ER-HGP86 - Panasonic - 9

A Main body

PANASONIC ER-HGP86 - A Main body - 1

Notes

Maintenance

▶ Main body / Blade

▶ Charging base

▶ Mounting

Spare parts

① AC adapter (RE9-82)

⑨ Adapter

⑩ Power plug

⑪ Cord

⑫ Stick to the device

Accessories

J Cleaning brush

K Lubricating oil

L Bag

Charging

Maintenance

▶ Charging stand

Use the cleaning brush to remove hair and dust from the charging socket or the hole on the underside.

PANASONIC ER-HGP86 - ▶ Charging stand - 1

PANASONIC ER-HGP86 - ▶ Charging stand - 2

How to attach and remove the blade

▶ Attach

  1. Set the dial to "1.5".

Medical illustration showing a surgical procedure on implant placement, with labeled steps (a) and (b) indicating anatomical changes.

Spare parts

Troubleshooting

Problem Handling

Maintenance

▶ Assembly

  1. Set the dial to "1.5".

Diagram illustrating a mechanical assembly process with labeled parts (a, b) and a magnified view of the component being inserted.

Spare parts

PANASONIC ER-HGP86 - Spare parts - 1

PANASONIC ER-HGP86 - Spare parts - 2

PANASONIC ER-HGP86 - Spare parts - 3

PANASONIC ER-HGP86 - Spare parts - 4

① AC adapter (RE9-82)

Maintenance

▶ Charging stand

▶ Assembly

  1. Set the dial to "1.5".

Medical illustration showing a surgical procedure with labeled steps (a, b) and magnified views of the procedure.

Spare parts

Spare parts are available from the dealer or a service workshop.

Reservedeler for ER-HGP86Blad WER9930
Smøreolje WES003P

Troubleshooting

Problem Handling

Maintenance

▶ Table charger

Assembly

Replaceable parts

Troubleshooting

Problem Action

The device is sluggish.

Maintenance

▶ Charging stand

▶ Attach

Spare parts

Troubleshooting

Maintenance

Medical diagram showing a surgical procedure with labeled parts (a) and (b), likely illustrating a procedure in a surgical setting.

Diagram showing a device with a magnified view of its internal structure.

Spare parts

PANASONIC ER-HGP86 - Spare parts - 1

PANASONIC ER-HGP86 - Spare parts - 2

PANASONIC ER-HGP86 - Spare parts - 3

PANASONIC ER-HGP86 - Spare parts - 4

PANASONIC ER-HGP86 - Spare parts - 5

PANASONIC ER-HGP86 - Spare parts - 6

PANASONIC ER-HGP86 - Spare parts - 7

PANASONIC ER-HGP86 - Spare parts - 8

PANASONIC ER-HGP86 - Spare parts - 9

A Main part

Maintenance

▶ Charging stand

▶ Installation

  1. Set the dial to "1.5".

Diagram illustrating a mechanical or biological process with labeled parts (a, b) and magnified views showing steps to process a component.

Spare parts

Troubleshooting

Maintenance

▶ Charging stand

Use the cleaning brush to remove hair and dust residue from the charging plug or from the opening on the bottom surface.

PANASONIC ER-HGP86 - ▶ Charging stand - 1

PANASONIC ER-HGP86 - ▶ Charging stand - 2

Removing and attaching the blade

▶ Loading

Diagram illustrating a mechanical assembly process with labeled parts (a, b) and a magnified view of the component being inserted.

Spare parts

Troubleshooting

Maintenance

▶ Charging stand

▶ Installation

Spare parts

Troubleshooting

① AC adapter (RE9-82)

⑨ Adapter

Maintenance

▶ Charging cradle

▶ Mounting

  1. Position the disc at "1.5".

Diagram illustrating a mechanical assembly process with labeled parts (a) and a magnified view of the component being inserted into a device.

Spare parts

Troubleshooting

Maintenance

▶ Charging cradle

▶ Mounting

Spare parts

Troubleshooting

Problem Action

The device has become dull.

Maintenance

▶ Charging base

▶ Place

Spare parts

Authorized Representative in EU:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Manufactured by:

Panasonic Corporation

1006, Oaza Kadoma, Kadoma City, Osaka, Japan

(SP)

Importer:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Manufactured by:

Panasonic Corporation

1006, Oaza Kadoma, Kadoma, Osaka, Japan

(PT)

Importer:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Manufactured by:

Panasonic Corporation

1006, Oaza Kadoma, Kadoma, Osaka, Japan

(SV)

Importer:

Panasonic Marketing Europe GmbH

Authorized representative in the EU:

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Manufactured by:

Panasonic Corporation

1006, Oaza Kadoma, Kadoma, Osaka, Japan

(FI)

Importer:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Manufacturer:

Panasonic Corporation

1006, Oaza Kadoma, Kadoma City, Osaka, Japan

(PL)

Importer:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Panasonic Testing Centre

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Manufacturer:

Panasonic Corporation

1006, Oaza Kadoma, Kadoma City, Osaka, Japan

(HU)

Importer:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Manufactured by:

Panasonic Corporation

1006, Oaza Kadoma, Kadoma City, Osaka, Japan

(TR)

Importer:

Panasonic Marketing Europe GmbH

Panasonic Testing Centre

Winsbergring 15, 22525 Hamburg, Germany

Panasonic Testing Centre

© Panasonic Corporation 2022

⑤ EN, SP, DA, PT, NB, SV, FI, PL, CS, SK, HU, RO, TR, GR

Printed in Japan

ER9710HGP861E Y0622-0

Manual assistant
Powered by Anthropic
Waiting for your message
Product information

Brand : PANASONIC

Model : ER-HGP86

Category : Beard trimmer