PMGS 12 A1 - Electric rotary tool PARKSIDE - Free user manual and instructions

Product Type	Cordless Angle Grinder
Brand	Parkside
Model	PMGS 12 A1
Voltage	12 V
Battery System	Parkside X 12 V Team
Disc Diameter	115 mm (4.5 in)
No-Load Speed	8500 rpm
Spindle Thread	M14
Weight (without battery)	1.5 kg (3.3 lb)
Protection Class	IP X0 (basic protection)
Safety Features	Spindle lock, adjustable guard, two-stage safety switch
Soft Start	Yes
Overload Protection	Electronic overload protection
Battery Protection	Overdischarge, overcurrent, and temperature protection
Charger Included	Yes (depending on set)
Charging Time (2.0 Ah)	Approx. 1 hour
Maintenance	Clean vents regularly, check carbon brushes, keep dry
Accessories Included	1 cutting disc, 1 grinding disc, spanner
Repairability	Carbon brushes replaceable; spare parts available via Parkside service
Warranty	3 years (registration required)

Frequently Asked Questions - PMGS 12 A1 PARKSIDE

What battery does the Parkside PMGS 12 A1 use?

The PMGS 12 A1 is compatible with all batteries from the Parkside X 12 V Team series. Common capacities are 2.0 Ah and 4.0 Ah.

Can I use cutting discs other than 115 mm?

The grinder is designed for 115 mm (4.5 inch) discs with a bore of 22.2 mm. Using other sizes may be unsafe.

How do I change the disc on the PMGS 12 A1?

Press the spindle lock button to lock the spindle, then use the supplied spanner to loosen the flange nut. Replace the disc and tighten the nut.

Does the PMGS 12 A1 have a soft start?

Yes, the motor slowly ramps up to speed to reduce kickback and start-up torque.

Can I use the grinder for woodworking?

The PMGS 12 A1 is intended for metal and stone cutting/grinding. Using it on wood with appropriate discs may be possible but check safety guidelines.

What is the weight of the tool without battery?

The tool weighs approximately 1.5 kg (3.3 lbs) without battery.

How do I clean the PMGS 12 A1?

Use a dry or slightly damp cloth. Do not use solvents. Clean ventilation slots regularly with a brush or compressed air.

Are replacement carbon brushes available?

Yes, carbon brushes are replaceable. Contact Parkside service or check the manual for part numbers.

What does the LED on the charger indicate?

A steady red light means charging; green means fully charged; flashing red indicates a fault. Refer to the charger manual.

Can I use the grinder while charging the battery?

No, the battery must be removed from the tool before charging. Do not connect the charger to the tool.

USER MANUAL PMGS 12 A1 PARKSIDE

GB

MODELLING AND ENGRAVING SET

Operation and Safety Notes

Translation of original operation manual

RO

SET GRAVARE ŞI MODELARE

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

HR

Prije nego što pročitate tekst, otvorite stranicu sa slikama i upoznajte se na osnovu toga sa svim funkcijama uređaja.

RO

GB Operation and Safety Notes Page 5

HR Upute za posluživanje i za Vašu sigurnost Stranica 17

Introduction

Proper use....Page 6

Features and equipment....Page 6

Included items Page 7

Technical information......Page 7

General safety advice for electrical power tools......Page 7

1. Workplace safety ......Page 8

2. Electrical safety Page 8

3. Personal safety......Page 8

4. Careful handling and use of electrical power tools....Page 9

Safety advice for all uses....Page 9

Safety advice relating to kickback......Page 10

Special safety advice relating to grinding and disc-cutting......Page 11

Further special safety advice for disc-cutting......Page 11

Special safety advice for abrading using sandpaper Page 12

Special safety advice for polishing......Page 12

Special safety advice for working with wire brushes......Page 12

Device-specific safety instructions for small drill PMGS 12 B2 and

mains adapter-PMGS 12 B2-1 Page 12

Operation

Inserting or replacing a tool / collet......Page 13

Switching on and off / Setting the speed range......Page 13

Advice on working with materials/Tools/Speed ranges ......Page 14

Tips and tricks......Page 14

Maintenance and cleaning......Page 15

Service Page 15

Warranty Page 15

Disposal Page 15

Conformity Declaration / Manufacturer......Page 16

The following pictograms are used in these operating instructions / on the device:
	Read instruction manual!		Keep children away from electrical power tools!
	Volt (AC)		Caution - electric shock!Danger to life!
	Watts (Effective power) For indoor use or
	Direct current(Type of current and voltage)		Risk of loss of life by electric shock from damaged mains lead or mains plug!
	Design no-load speed		Wear hearing protection, dust protection mask, protective glasses and protective gloves.
	Milliamps/Amps/Amp-hours		Avoid contact with rapidly rotating tools!
	Safety class II Risk of fire!
	Observe caution and safety notes! Prope		and handling.
	Risk of explosion!!		Dispose packaging and appliance in an environmentally-friendly way!

Modelling and engraving set PMGS 12 B2

- Introduction

Please make sure you familiarise yourself fully with the way the device works before you use it for the first time and that you

understand how to handle electrical power tools correctly. To help you do this please read the accompanying operating instructions. Keep these instructions in a safe place. If you pass the device on to anyone else, please ensure that you also pass on all the documentation.

- Proper use

The small drill is to be used for drilling, milling, engraving, polishing, cleaning up, grinding, separating

and sawing of wood, metal, plastic, ceramic or stone in dry rooms. Any other use or modification to the drill / grinder shall be considered as improper use and could give rise to considerable dangers. The manufacturer will not accept liability for loss or damage arising from improper use. Not intended for commercial use.

● Features and equipment

Small drill:

1 Rotational speed control
2 ON/OFF switch
3 Metal stirrup hanger
4 Plug for mains adapter
5 Clamping nut
6 Spigot nut
7 Spindle lock

Mains adapter (see Fig. A):

8	Plug-in device for plug 4
9	Tray
10	Mains adapter
11	Power cable (with mains plug)

Accessories (see Fig. B):

12	6 HSS drills
13	2 Mandrels for mounting tools
14	3 Polishing wheels
15	4 Grinding wheels
16	1 Metal brush
17	16 Cutting wheels
18	5 Collets
19	2 Plastic brushes
20	3 Milling bits
21	2 Engraving bits
22	5 Grinding bits
23	1 Combination tool

- Included items

1 Small drill
1 Mains adapter
1 Plastic case
1 Accessory kit (50-piece)
1 Operating instructions

● Technical information

Small drill PMGS 12 B2:

Nominal voltage: 12 V ===

Nominal output: 22 W

Idle-running speed: n 0 5000-20000 min -1

Max. drill bit diameter: ø 3.2 mm

Certified acc. to:EN60745-1;EN60745-2-1

EN60745-2-3

Noise and vibration data:

Measured values for noise are determined in accordance with EN 60745. The A-weighted noise level of the electrical power tool are typically:Sound pressure level: 54.70 dB(A)Sound power level: 65.70 dB(A)Uncertainty K: 3 dB

Evaluated acceleration, typical:

Hand / arm vibration: 1.868 m/s2

Uncertainty K = 1.5 m/s2

WARNING! The vibration level given in these instructions has been measured in accordance with a standardised measurement procedure specified in EN 60745 and can be used to compare devices. Different uses of the device give rise to different vibration levels and in many cases they may exceed the values given in these instructions. It is easy to underestimate the vibration load if the electrical power tool is used regularly in particular circumstances.

Note: If you wish to make an accurate assessment of the vibration loads experienced during a particular period of working, you should also take into account the intervening periods of time when the device is switched off or is running but is not actually in use. This can result in a much lower vibration load over the whole of the period of working.

Mains adapter PMGS 12 B2-1: INPUT:

Rated voltage:

230 V~ 50 Hz

OUTPUT:

Nominal voltage:	12V---
Nominal current:	1A
Protection class:	II/□
Certified acc. to:	EN61558

General safety advice for electrical power tools

WARNING! Read all the safety advice and instructions! Failure to observe the safety advice and instructions may result in electric shock, fire and / or serious injury.

Keep all the safety advice and instructions in a safe place for future reference!

The term "electrical tool" used in the safety advice refers to electrical tools powered by mains electricity (by means of a mains lead) and electrical tools

powered by rechargeable batteries (without a mains lead).

1. Workplace safety

a) Keep your working area clean and well lit. Untidy or poorly lit working areas can lead to accidents.

b) Do not work with the device in potentially explosive environments in which there are inflammable liquids, gases or dusts.

Electrical power tools create sparks, which can ignite dusts or fumes.

c) Keep children and other people away while you are operating the electrical tool.

Distractions can cause you to lose control of the device.

2. Electrical safety

a) The mains plug on the device must match the mains socket. The plug must not be modified in any way. Do not use an adapter plug with devices fitted with a protective earth. Unmodified plugs and matching sockets reduce the risk of electric shock.

b) Avoid touching earthed surfaces such as pipes, radiators, ovens and refrigerators with any part of your body. There is an increased risk of electric shock if your body is earthed.

c) Keep the device away from rain or moisture. Water entering an electrical device increases the risk of electric shock.

d) Do not use the mains lead for any purpose for which it was not intended, e.g. to carry the device, to hang up the device or to pull the mains plug out of the mains socket. Keep the mains lead away from heat, oil, sharp edges or moving parts of the device. Damaged or tangled mains leads increase the risk of electric shock.

e) When working outdoors with an electrical power tool always use extension cables that are also approved for use outdoors. The use of an extension cable suitable for outdoor use reduces the risk of electric shock.

f) Use a residual current device (RCD) for protection if operating the electrical power tool in a moist environment is unavoidable. The use of an RCD reduces the risk of electric shock.

3. Personal safety

a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury.

b) Wear personal protective equipment and always wear safety glasses. The wearing of

personal protective equipment such as dust masks, non-slip safety shoes, safety helmets or ear protectors, appropriate to the type of electrical power tool used and work undertaken, reduces the risk of injury.

c) Avoid unintentional operation of the device. Check that the electrical power tool is switched off before you connect it to the mains, pick it up or carry it. Accidents can happen if you carry the device with your finger on the ON/OFF switch or with the device switched on.

d) Remove any setting tools or spanners before you switch the device on. A tool or spanner left attached to a rotating part of a device can lead to injury.

e) Avoid placing your body in an unnatural position. Keep proper footing and balance at all times. By doing this you will be in a better position to control the device in unforeseen circumstances.

f) Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves clear of moving parts. Loose clothing, jewellery or long hair can become trapped in moving parts.

g) If vacuum dust extraction and collection devices are fitted do not forget to check that they are properly connected and correctly used. The use of these devices reduces the hazard presented by dust.

4. Careful handling and use of electrical power tools

a) Do not overload the device. Always use an electrical power tool that is intended for the task you are undertaking. By using the right electrical power tool for the job you will work more safely and achieve a better result.
b) Do not use an electrical power tool if its switch is defective. An electrical power tool that can no longer be switched on and off is dangerous and must be repaired.
c) Pull the mains plug from the socket before you make any adjustments to the device, change accessories or when the device is put away. This precaution is intended to prevent you from unintentionally starting the device.
d) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people.
e) Look after the device carefully. Check that moving parts are working properly and move freely. Check for any parts that are broken or damaged enough to detrimentally affect the functioning of the device. Have damaged parts repaired before you use the device. Many accidents have their origins in poorly maintained electrical power tools.
f) Keep cutting tools clean and sharp. Carefully maintained cutting tools with sharp

cutting edges are less likely to jam and are easier to control.

g) Use the electrical power tool, accessories, inserted tools etc. in accordance with these instructions and advice, and the stipulations drawn up for this particular type of device. In doing this, take into account the working conditions and the task in hand. The use of electrical power tools for purposes other than those intended can lead to dangerous situations.

● Safety advice for all uses

General safety advice for grinding, sanding (with sandpaper), wire brushing, polishing and disc-cutting:

a) This electrical power tool is intended for use as a grinding, sanding, wire-brushing, and disc-cutting machine. Observe all the safety advice, instructions, information in figures and all other information you received with this device. If you do not observe the following advice it could lead to electric shock, fire and / or serious injury.
b) Normative statement / advice for this tool is not applicable.
c) Do not use any accessory not specifically intended by the manufacturer for this electrical power tool. Although an accessory may fit on your electrical power tool, this does not on its own guarantee that it can be safely used.
d) The maximum permitted speed of an attachment must be at least as high as the maximum speed indicated for the electrical power tool. An accessory rotating faster than its permitted speed could disintegrate or fly off.
e) The external diameter and the thickness of the attachment must be compatible with the dimensions of your electrical power tool. Attachments that are not dimensionally compatible cannot be adequately guarded or controlled.

f) Grinding discs, flanges, grinding wheels or other accessories must fit exactly on to the spindle of your electrical power tool. Attachments that do not exactly fit on the spindle turn unevenly, vibrate severely and could lead to loss of control.
g) Do not use damaged attachments. Before every use check attachments such as grinding discs for loose fragments and cracks, grinding wheels for cracks, deterioration or excessive wear and wire brushes for loose or broken wires. If the electrical power tool or attachment is dropped, inspect for damage or change the attachment for an undamaged one. When you have inspected and inserted the attachment, position yourself and bystanders away from the plane of the rotating attachment and run the device at maximum speed for one minute.

Damaged attachments will usually break apart during this test.

Wear personal protective equipment. Use a full face vis- sor, safety goggles or safety glasses, depending on the application. Wear a dust mask, hearing protectors, safety gloves or special apron capable of stopping particles of the grinding medium or workpiece, as appropriate for the task. Eyes must be protected from the flying debris which can arise from some operations. Dust or breathing masks must be capable of filtering out the dust generated by the application. Prolonged exposure to loud noise can lead to hearing loss.

i) Keep bystanders at a safe distance from your work area. Anyone entering the work area must wear personal protective equipment. Fragments of the workpiece or of a broken attachment could fly off and cause injury beyond the immediate working area.
j) Hold the device by the insulated handle surfaces when you are undertaking work where there is the danger of the attachment striking hidden

electricity cables or the device's mains lead. Contact with a live wire could cause metal parts of the device to become live and lead to electric shock.

k) Keep the mains lead away from rotating attachments. If you lose control of the device the mains lead may become severed or trapped and your hand or arm may be pulled into the rotating attachment.
I) Never lay the electrical power tool down until after the attachment has come to a complete standstill. The rotating attachment may snag when it comes into contact with the surface and cause you to lose control of the device.
m) Do not have the electrical power tool running while you are carrying it. Your clothing could become trapped by unintentional contact with the rotating attachment and the tool could be pulled into your body.
n) Clean the ventilation slots on your electrical power tool regularly. The motor's fan draws dust into the housing. A build-up of metal dust could give rise to an electrical hazard.

Never use the electrical power tool near inflammable materials. Sparks could ignite

these materials.

p) Do not use attachments that require the use of coolants. The use of water or other liquid coolants could result in electric shock.

● Safety advice relating to kickback

Kickback is the sudden reaction to a pinched or snagged rotating attachment, such as a grinding disc, grinding pad, wire brush etc. Pinching or snagging results in the rotating attachment coming to an abrupt stop. This causes the electrical power tool (if not controlled) to move in the opposite direction to the direction of rotation of the attachment at the point of constraint.

If, for example, a grinding disc is pinched or snags in a workpiece, this can cause the edge of the

grinding disc to penetrate the workpiece, become trapped there and either free itself or kickback. The grinding disc moves towards or away from the operator, depending on the direction of movement of the disc at the point of constraint. The grinding disc could also break.

Kickback occurs as a result of incorrect use or misuse of the electrical power tool. It can be prevented by taking the appropriate precautions as described below.

a) Maintain a firm grip on the electrical power tool and position your body and arms to allow you to resist kickback forces. Always use the auxiliary handle, if provided, to exercise the greatest possible control over kickback forces or reaction torques as the device builds up to full speed. By taking suitable precautions the operator can control kickback and reaction forces.
b) Do not place your hands near a rotating attachment. If kickback occurs the attachment could move over your hand.
c) Avoid positioning your body in the area into which the electrical power tool would move in the event of a kickback. A kickback moves the electrical power tool in the opposite direction to the direction of movement of the grinding disc at the point of constraint.
d) Work particularly carefully in the area of corners, sharp edges etc. to avoid the attachment bouncing or snagging on the workpiece. Corners, sharp edges or bouncing have a tendency to snag the rotating attachment. This causes loss of control or kickback.
e) Do not use saw-chain woodcarving discs or toothed discs. Such attachments create frequent kickback and loss of control of the electrical power tool.

● Special safety advice relating to grinding and disc-cutting

a) Always use the guard designed for the type of abrasive consumable you are using. Always use abrasive consumables approved for use with your electrical power tool. Abrasive consumables not approved for use with your electrical power tool cannot be adequately guarded and are unsafe.
b) To ensure the highest level of operational safety, the disc guard cover must be attached to the electrical power tool and set in such a way that the smallest possible area of the abrasive consumable is exposed to the operator. The disc guard cover is there to protect the operator from pieces breaking off and accidental contact with the abrasive consumable.
c) Abrasive consumables must be used only for their recommended purposes, For example: never grind with the side face of a cutting disc. Cutting discs are intended for removing material using the edge of the disc. Sideways forces on these abrasive consumables can cause them to break.
d) Always use an undamaged mounting flange of the correct size and shape for your selected grinding disc. Suitable flanges support the grinding disc and reduce the chance of it breaking. Flanges for cutting discs are different from the flanges for other abrasive discs.
e) Never use worn down abrasive consumables intended for larger electrical power tools. Abrasive consumables intended for larger electrical power tools are not designed for the faster rotational speeds of these smaller electrical power tools and could break.
● Further special safety advice for disc-cutting
a) Avoid snagging the cutting disc and do not use too much contact pressure. Do not attempt to make excessively deep cuts. Overloading the cutting disc increases the load and the tendency of the disc

to twist or snag in the cut, making kickback or disc breakage more likely.

b) Avoid the area in front of or behind the rotating cutting disc. If the cutting disc is moving away from you at the point of constraint in the workpiece, then, in the event of a kickback, the electrical power tool and the rotating disc may be thrown towards you.
c) If the cutting disc jams or you stop work for a while, switch the device off and hold it until the disc comes to a complete stop. Never attempt to pull the still rotating cutting disc out of the cut as this could cause kickback. Determine and rectify the reason for the jamming.
d) Do not switch on the device if the cutting disc is in the workpiece. Allow the cutting disc to reach full speed before carefully continuing with the cut. Otherwise the disc could snag, jump out of the workpiece or cause a kickback.
e) Support boards or workpieces whilst cutting to reduce the risk of kickback caused by a jammed cutting disc. Large workpieces may bend under their own weight. The workpiece must be supported to both sides of the cutting disc and particularly near the cutting disc and at the workpiece edge.
f) eParticularly careful when pocket cutting in existing walls or other areas where you cannot see what you are cutting into. The cutting disc plunged into the surface could cut through gas or water pipes, electricity cables or other objects and cause kickback.
- Special safety advice for abrading using sandpaper
- Do not use over-sized sanding sheets. Follow the manufacturer's recommendations for sanding sheet size. Sanding sheets that project beyond the backing pad could cause injury in addition to jamming, tearing of the sheet or kickback.

• Special safety advice for polishing
Do not use the polishing bonnet if it has any loose parts, in particular the fastening cords. Tuck the fastening cords away or trim them. Loose fastening cords rotating with the attachment could catch your fingers or become trapped in the workpiece.
- Special safety advice for working with wire brushes

a) Bear in mind that wire brushes lose pieces of wire during normal use. Do not overload the wires by applying too much pressure. Flying pieces of wire can very easily penetrate thin clothing and / or skin.

b) a guard, if recommended, but make sure that the wire brush does not come into contact with the guard. The diameters of disc brushes and cup brushes can increase due to contact pressure and centripetal forces.

Device-specific safety instructions for small drill PMGS 12 B2 and mains adapter-PMGS 12 B2-1

When you use the drill / grinder wear the following protective equipment: safety glasses and protective gloves.
CAUTION! The tool continues to rotate after it has been switched off! Avoid contact with rapidly rotating drill/grinder components.
WARNING! Securely support the workpiece. Use clamps or a vice to grip the workpiece firmly. This is much safer than holding it in your hand.
WARNING! Never support yourself by placing your hands near or in front of the device or the workpiece surface. A slip can result in injury.

- Avoid contact with moving sanding or grinding tools.

DANGER OF FIRE FROM FLYING SPARKS! Abrading metal creates flying sparks. For this reason, always

make sure that nobody is placed in any danger and that there are no inflammable materials near the working area.

DUTHEMARD! Any

harmful / noxious dusts generated from machining represent a risk to the health of the person operating the device and to anyone near the work area.

Wear a dust mask!

NOXWORSHUJES!

Ensure that there is adequate ventilation when machining surfaces containing plastic or covered with paint, varnish etc.

- Do not soak the materials or the surface you are about to work on with liquids containing solvents.

- Avoid abrading paints containing lead or other substances hazardous to health.

Do not machine materials containing asbestos. Asbestos is a known carcinogen.

- Do not machine moist materials or damp surfaces.

NOTE! Do not allow the tool to come to a standstill by overloading it!

■ My WAINING and allow it to come to a standstill be- fore you put it down.

■ Always keep the de vice clean, dry and free of oil or grease.

Children or persons who lack the knowledge or experience to use the device or whose physical, sensory or intellectual capacities are limited must never be allowed to use the device without supervision or instruction by a person responsible for their safety. Children must never be allowed to play with the device.

Operation

■ Never use the device for a purpose for which it was not intended or with non-original parts/accessories. The use of tools or accessories other than those recommended in the operating instructions could lead to you suffering an injury.

- Inserting or replacing a tool / collet

☐ Press the spindle lock 7 and keep it pressed.

☐ Rotate the clamping nut 5 until the lock engages.

☐ Loosen the clamping nut 5 with the combination key 23.

☐ If a tool is already inserted, remove it.

☐ First insert the tool you wish to use though the clamping nut 5 before you insert it into the collet 18 suitable for the tool shaft.

☐ Press the spindle lock 7 and keep it pressed.

☐ Insert the collet 18 into the threaded insert and tighten the clamping nut 5 on the thread using the combination key 23.

Using the Insertion tool with mandrel 13: NOTE: Use the screwdriver end of the combination key 23 to release or tighten the screw of the mandrels 13.

☐ Insert the mandrel 13 into the electrical tool as described.

☐ With the aid of the combination wrench 23, unscrew the screw from the mandrel 13.

Place the insertion tool you wish to have onto the screw between the two washers.

☐ With the aid of the combination wrench 23, tighten the screw on the mandrel 13.

- Switching on and off / Setting the speed range

Switching on / Setting the speed range:

☐ Connect the plug 4 to the power supply unit 10 by inserting it into the plug-in device 8 provided for such purposes (see Fig. C).

Operation

☐ Connect the device to the power supply by inserting the mains plug into the socket.
Press down the ON / OFF switch and then move it in direction of the rotational speed control 1. Then set the rotational speed control to a position between "5" and "20".

Switching off:

Set the rotational speed control to position "5". Press down the ON / OFF switch 2 and then move it in direction of the cable.

● Advice on working with materials/Tools/Speed ranges

☐ Use the highest speed when working on steel or iron with the milling bits 20.
☐ Use a short trial on a test piece to determine the optimum rotational speed range for working on zinc, zinc alloy, aluminium, copper and lead.
☐ Use the low speed range for working on plastics and low-melting point materials.
□ Use high speeds on wood.
☐ Use the medium speed range for cleaning, polishing and buffing.

The following information shall be considered as recommendatory only. Learn by practical experience which tools and settings are the best for the materials you work with.

Setting the appropriate speed:

Numeral on the rotational speed control 1	Material to be worked on
5	Plastics and low melting point materials
8	Stone, Ceramics
12	Softwood, metal
16	Hardwood
20	Steel

Examples of appropriate tool selection Function:

Function Accessory Application
Drilling	HSS drill 12	Drilling wood
Milling Milling bits 20	Various tasks, e.g. hollowing out, gouging, shaping, grooving or slotting
Engraving Engraving bits 21	Making marks, craft projects (see Fig. D)
Polishing, derusting	Metal brush 16	Derusting
⚠CAUTION! Use only the lightest contact pressure of the tool on the work-piece.	Polishing wheel 14	Working on various metals and plastics, in particular noble metals like gold or silver (see Fig. E)
Cleaning Plastic brush 19	E.g. cleaning complex plastic housings or the area around a door lock
Grinding Grinding wheels 15, grinding bits 22	Grinding work on stone, wood; fine work on hard materials such as ceramic or alloyed steel (see Figs. F, G)
Cutting and sawing	Cutting discs 17	Cutting metal, plastic or wood

- Tips and tricks

If you use press too hard you run the risk of breaking the tool or damaging the workpiece. You will achieve the best results by operating the tool at a constant rotational speed and using a low contact pressure on the workpiece.

● Maintenance and cleaning

The device is maintenance-free.

□ Clean all the dirt off the drill / grinder. Use a dry cloth for cleaning.

- Service

Aute YoNt device repaired at the service centre or by qualified specialist personnel using original manufacturer parts only. This will ensure that your device remains safe to use.

■ The WORLICK ad needs to be replaced, always have the replacement carried out by the manufacturer or its service centre. This will ensure that your device remains safe to use.

- Warranty

The warranty for this appliance is for 3 years from the date of purchase. The appliance has been manufactured with care and meticulously examined before delivery. Please retain your receipt as proof of purchase. In the event of a warranty claim, please make contact by telephone with our Service Department. Only in this way can a post-free despatch for your goods be assured.

The warranty covers only claims for material and manufacturing defects, but not for transport damage, for wearing parts or for damage to fragile components, e.g. buttons or batteries. This product is for private use only and is not intended for commercial use.

The warranty is void in the case of abusive and improper handling, use of force and internal tampering not carried out by our authorized service branch. Your statutory rights are not restricted in any way by this warranty.

The warranty period will not be extended by repairs made unter warranty. This applies also to replaced

and repaired parts. Any damage and defects extant on purchase must be reported immediately after unpacking the appliance, at the latest, two days after the purchase date. Repairs made after the expiration of the warranty period are subject to payment.

GB Service Great Britain Tel.: [phone] (0,10 GBP/Min.)

e-mail: [e-mail]

IAN 66445

IE Service Ireland Tel: [phone] (0,08 EUR/Min. (peak) 0,06 EUR/Min. (off peak)) e-mail: [e-mail]

IAN 66445

The packaging is wholly composed of environmentally-friendly materials that can be disposed of at a local recycling centre.

Do not dispose of electric tools in the household waste!

In accordance with European Directive 2002 / 96 / EC about waste electrical and electronic equipment and its transposition into national legislation, worn out electric tools must be collected separately and taken for environmentally compatible recycling.

Please contact your municipal or city council to ask about how to dispose of old electrical tools.

● Conformity Declaration / Manufacturer CE

We, Kompernaß GmbH, the person responsible for documents: Mr Semi Uguzlu, Burgstr. 21, D-44867 Bochum, Germany, hereby declare that this product complies with the following standards, normative documents and EU directives:

Machinery Directive (2006/42/EC)

EU Low Voltage Directive (2006/95/EC)

Electromagnetic compatibility (2004/108/EC)

Applicable harmonized standards

EN 60745-1:2009, EN 60745-2-1:2010
EN 60745-2-3:2007+A11
EN 55014-1:2006+A1
EN 55014-2:1997+A1+A2
EN 61558-1:1997+A1+A11, EN 61558-2-6:1997
EN 61000-3-2:2006+A1+A2
EN 61000-3-3:2008

Type / Device description:

Modelling and engraving set PMGS 12 B2

Date of manufacture (DOM): 09-2011 Serial number: IAN 66445

Bochum, 30.09.2011

Semi Uguzlu

- Quality Manager -

We reserve the right to make technical modifications in the course of further development.

Uvod

Namjenska uporaba....Stranica 18

Oprema....Stranica 18

Opseg pošiljke....Stranica 19

Tehnički podaci....Stranica 19

Nazivni napon: 12 V ---

Nazivna snaga: 22 W

Praznohodna

brzina vrtnje: n 0 5000-20000 min ^-1

Maks. bušilice: ∅ 3,2 mm

provjerenosukladno:EN60745-1;EN60745-2-1

EN60745-2-3

Informacija o buci i vibraciji:

44867 Bochum (Germany)

Njemačka

HR

Servis Hrvatska

Tel.: [phone]

e-mail: [e-mail]

IAN 66445

/// PARKSIDE

- Otklanjanje otpada

Semi Uguzlu

- Menadžer kakvoće -

Izjava o sukladnosti za ovaj proizvod dostupna je na internet stranici www.lidl.hr.

© by ORFGEN Marketing

Last Information Update · Stanje informacija · Versiunea