Scout RX3 - Vacuum Cleaner MIELE - Free user manual and instructions

Product type	Robot vacuum cleaner
Brand	Miele
Model	Scout RX3
Dimensions (diameter x height)	33 cm x 9.2 cm
Weight	3.5 kg
Power supply	Li-Ion battery 2600 mAh
Runtime	Up to 120 minutes
Charging time	Approximately 3 hours
Dustbin capacity	0.6 L
Filtration	Washable HEPA filter
Navigation	Laser mapping (LiDAR)
Smart features	Miele app, voice control (Alexa, Google Assistant), scheduling, no-go zones
Brushes	Main brush, side brush
Sensors	Floor sensors, obstacle detection, drop sensor
Noise level	Approximately 50 dB
Maintenance	Regular cleaning of sensors and brushes, emptying dustbin
Safety	Auto shut-off if lifted, drop detection
Spare parts	Filter, brushes, battery, dustbin available
Repairability	Repairability rating 7.6/10
Warranty	2 years

Frequently Asked Questions - Scout RX3 MIELE

How to reset my Miele Scout RX3?

Hold down the power button for 10 seconds until the LED flashes. Refer to the manual for more details.

What to do if the vacuum does not connect to the app?

Check that Wi-Fi is enabled and you are using the 2.4 GHz frequency. Restart the device and the router. Update the Miele app.

How to clean the sensors of the Scout RX3?

Use a soft, dry cloth to wipe the optical sensors and drop sensors. Avoid chemical products.

What is the battery lifespan?

Approximately 300 charge cycles. Replace the battery when runtime decreases significantly.

How to create a no-go zone?

In the Miele app, use the 'no-go zones' function by drawing rectangles on the map. The vacuum will avoid these areas.

The robot does not return to its charging station, what to do?

Check that the path is clear and the station is plugged in. Clean the charging contacts on the robot and the station.

Can I use the vacuum on carpet?

Yes, the Scout RX3 is suitable for hard floors and short-pile carpets. It automatically adjusts suction power.

How to empty the dustbin?

Press the dustbin latch, remove it, empty it into a trash bin. Wash the HEPA filter every month.

The robot makes an abnormal noise, what to do?

Check if debris is stuck in the main brush or wheels. Clean and remove obstructions. If the noise persists, contact customer service.

How to schedule a daily cleaning?

In the Miele app, go to 'Scheduling' and set the desired days and times. The robot will start automatically.

USER MANUAL Scout RX3 MIELE

Operating instructions Robot vacuum cleaner

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

Warning and Safety instructions.... 44

Guide to the appliance 52

Caring for the environment 54

Functions and features of the robot vacuum cleaner.... 56

Accessories supplied 56

Connection.... 56

Use 59

Switching on and off 59

Starting vacuuming 59

Finishing vacuuming if vacuuming started from the base station.... 59

Finishing vacuuming if vacuuming started from somewhere in the room...... 59

Vacuuming manually 60

Interrupting vacuuming 60

Manual navigation (without vacuuming).... 60

Directing the robot vacuum cleaner to the base station 61

Operating modes....61

Selecting the operating mode 61

Quitting the current operating mode 62

Setting the timer.... 62

Deactivating the timer 63

Activating the timer/displaying a set start time 63

Deactivating the acoustic signals.... 63

Reducing the maximum crossing over height.... 64

"Scout RX" app.... 64

WiFi.... 64

Activating the network function of the robot vacuum cleaner 65

Video function 65

Removing the WiFi module 66

Maintenance 66

Emptying the dust box 67

Cleaning the dust box 67

Cleaning the exhaust filter 67

Cleaning the side brushes 68

Cleaning the roller brush 69

Cleaning the dust box seals 70

Replacing the seal unit on the dust box 70

Cleaning the front wheel 70

Cleaning the sensors 71

Replacing batteries in the remote control 71

Replacing the rechargeable battery 71

Cleaning and care 73

Storage/Factory default settings 73

Service.... 74

Contact in case of malfunction 74

Warranty 74

Problem solving guide 75

Error messages 78

Technical data.... 80

Conformity declaration 80

Copyright and licences 81

Electrical connection for the UK 82

Electrical connection AU, NZ 82

This robot vacuum cleaner complies with all current local and national safety requirements. Inappropriate use can lead to personal injury and damage to property.

Please read the operating instructions before using the robot vacuum cleaner for the first time. They contain important information on the safety, use and maintenance of the robot vacuum cleaner. This will prevent both personal injury and damage to the appliance.

In accordance with standard IEC 60335-1, Miele expressly and strongly advises that you read and follow the instructions in the “Connection” section as well as the safety instructions and warnings.

Miele cannot be held liable for injury or damage caused by non-compliance with these instructions.

Keep these operating instructions in a safe place and pass them on to any future owner.

Switch the robot vacuum cleaner off before any maintenance work and cleaning and if it is not going to be used for an extended period of time. It should also be switched off when dealing with problems. To do so, slide switch I/O on the side of the robot vacuum cleaner to the 0 position. The same should be done if you notice any unusual behaviour with your robot vacuum cleaner.

Correct application

This robot vacuum cleaner is intended for cleaning flooring in domestic households and similar residential environments. This robot vacuum cleaner is not suitable for use on construction sites. The robot vacuum cleaner is not intended for outdoor use. The robot vacuum cleaner must only be used for domestic household purposes to vacuum dry floor surfaces. Any other usage, modification or alteration is not supported by the manufacturer and could be dangerous.

The packaging material protects the robot vacuum cleaner from transport damage. We recommend you keep the packaging for transport purposes.

The robot vacuum cleaner can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, if they are supervised whilst using it or have been shown how to use it in a safe way and understand and recognise the consequences of incorrect operation.

Safety with children

Danger of suffocation. Packaging, e.g. plastic wrappings, must be kept out of the reach of babies and children. Whilst playing, children could become entangled in packaging or pull it over their head and suffocate.

Children under 8 years of age must be kept away from the robot vacuum cleaner unless they are constantly supervised.

Children aged 8 and older may only use the robot vacuum cleaner without supervision if they have been shown how to use it in a safe manner. Children must be able to understand and recognise the possible dangers caused by incorrect operation.

Children must not be allowed to clean or maintain the robot vacuum cleaner unsupervised.

Please supervise children in the vicinity of the robot vacuum cleaner and do not let them play with it.

Technical safety

The robot vacuum cleaner operates at 14.4 V.

It is classified as a class III appliance.

This appliance is supplied by a safety extra-low voltage (SELV) power source where the voltage is low enough to protect users from the risk of electrical shock. A Class II plug-in power supply is used for supplying power to charge the robot vacuum cleaner.

Before each use of the robot vacuum cleaner, check both the vacuum cleaner and all of the accessories supplied with it for any visible signs of damage. Do not use a damaged robot vacuum cleaner or accessory. The power socket for connecting the base station must be fitted with a 16 A or 10 A fuse. ▶ AUS/NZ: The mains electrical outlet must be fitted with an appropriate circuit breaker. ▶ Compare the connection data on the data plate of the robot vacuum cleaner and the power supply unit (mains voltage and frequency) with that of the mains electricity supply. This data must match exactly. ▶ Store the robot vacuum cleaner at an ambient temperature between 0 °C and 60 °C. While the robot vacuum cleaner is under warranty, repairs should only be undertaken by a Miele authorised service technician. Otherwise the warranty will be invalidated. ▶ Repairs should only be carried out by a Miele authorised service technician. Repairs and other work by unqualified persons can cause considerable danger to users. ▶ Ensure that you do not damage the power supply cable and avoid mechanical stress. Do not place heavy objects on the power supply cable. The robot vacuum cleaner is fitted with sensors to detect steps and drops in height. Do not cover these sensors or the camera, and ensure that the function of the sensors is not hindered by obstacles whilst the cleaner is moving. ▶ Do not let the robot vacuum cleaner travel over the mains cable or other cables.

Do not drop the robot vacuum cleaner or any of the accessories supplied with it. Items that have been dropped or damaged should not be used for safety reasons.

▶ AUS/NZ: The robot vacuum cleaner must only be supplied at safety extra low voltage corresponding to the marking on the appliance.

▶ Miele can only guarantee the safety of the appliance when genuine Miele replacement parts are used. Faulty components must only be replaced with genuine Miele replacement parts.

Cleaning

Do not immerse the robot vacuum cleaner or the parts supplied in water. Clean all parts with a dry or slightly damp cloth only.

Correct use

▶ Do not use the robot vacuum cleaner without the dust box, pre-filter and exhaust filter fitted.

Remove all breakable or lightweight items from the floor and make sure that the robot vacuum cleaner cannot become entangled in cords, curtains, fringes, cables or similar.

▶ Animals must be kept away from the robot vacuum cleaner. Do not allow animals to stand or sit on the robot vacuum cleaner.

▶ Take appropriate measures to prevent the robot vacuum cleaner falling down large drops, e.g. from galleries or balconies. This can be done, for instance, by setting up physical barriers.

Do not allow the robot vacuum cleaner to move any movable items, e.g. rugs, doormats, etc. Secure any movable items.

Do not use the robot vacuum cleaner to vacuum up anything which has been burning or is still glowing, e.g., cigarettes, ashes, or coal, whether glowing or apparently extinguished. Do not use the robot vacuum cleaner in the vicinity of a fireplace.

Do not use the robot vacuum cleaner to vacuum up any water, liquid, or damp dirt. Wait until any freshly cleaned or shampooed carpets or floor coverings are completely dry before attempting to vacuum. Do not use the robot vacuum cleaner to vacuum toner dust. Toner, such as that used in printers and photocopiers, can conduct electricity. Do not use the robot vacuum cleaner to vacuum up any inflammable or combustible liquids or gases and do not use it in areas where such substances are stored. Exercise constant care, and do not sit or lie on the surface being cleaned whilst the vacuum cleaner is running. This is to prevent the risk of loosely fitting clothes or long hair coming into contact with the roller brush or other moving parts of the robot vacuum cleaner.

Accessories

▶ Only use genuine accessories with the “ORIGINAL Miele” logo on the packaging. The manufacturer cannot otherwise guarantee the safety of the product.

Safety notes and warnings for rechargeable battery, base station, power supply unit and remote control batteries

Safety with children

▶ People (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, who are unable to use the base station/power supply unit safely may only use this robot vacuum cleaner if they are supervised whilst using it or have been shown how to use it in a safe way and understand and recognise the consequences of incorrect operation. Keep the rechargeable battery and the batteries for the remote control out of the reach of children. ▶ Children must be kept away from the base station and the power supply unit unless they are constantly supervised.

Technical safety

▶ Charge the robot vacuum cleaner at an ambient temperature between 10 °C and 45 °C.

The battery and the base station are designed for use with this Miele robot vacuum cleaner. For safety reasons, the robot vacuum cleaner must not be used with a battery or base station produced by another manufacturer.

▶ Only use the parts supplied for charging the robot vacuum cleaner (base station, power supply unit, power adapter).

▶ Reliable and safe operation of this robot vacuum cleaner can only be assured if the base station has been connected to the mains electricity supply.

▶ Do not attach any adhesive labels to the front of the base station as this conceals an infrared transmitter. Do not place any items in front of it.

▶ Stop using the rechargeable battery immediately if you notice an unusual smell from it, if liquid is leaking from it, if it is significantly overheating or if it is discoloured or deformed. Dispose of the battery immediately (see safety note “Disposing of the battery” at the end of this section as well as “Caring for the environment” – “Disposing of old batteries”).

▶ Batteries and rechargeable batteries will deplete over time. They can then leak corrosive fluids. Avoid contact with the eyes and skin. In the event of contact, rinse thoroughly with water and seek medical advice.

▶ AUS/NZ: To deal with leaking batteries, refer to the Safety Data Sheet (contact Miele to request a copy).

▶ Please contact Miele Customer Service Department before sending the rechargeable battery.

Correct use

▶ Do not drop or throw the rechargeable battery. For safety reasons, do not continue to use a battery which has been damaged.

Keep the rechargeable battery or the batteries away from naked flames or other heat sources. Do not heat the rechargeable battery or the batteries. Do not expose them to direct sunlight.

▶ Do not dismantle the rechargeable battery.

Do not cause a short circuit by bridging the contacts of the rechargeable battery or the batteries, either unintentionally or deliberately.

Do not allow the rechargeable battery or the batteries to come into contact with liquids.

Do not attempt to recharge the remote control batteries provided.

▶ Disposing of the batteries and the rechargeable battery: remove the rechargeable battery from the robot vacuum cleaner and the batteries from the remote control. Insulate the metal contacts with adhesive tape to prevent short circuits. Dispose of the batteries and the rechargeable battery in a municipal recycling facility. Do not dispose of batteries or the rechargeable battery with normal household waste.

The battery must be removed before the appliance is scrapped.

Illustrations A, B and C for this section are on the pull-out pages in the back of these operating instructions.

A – Robot vacuum cleaner top and bottom

① Display ② WiFi indicator ③ Video function indicator (for Scout RX3 Home Vision HD) ④ Time mode indicator (am/pm) ⑤ Cameras ⑥ Start/Pause sensor control (▶II) ⑦ Impact protection ⑧ On/Off switch (I/O) ⑨ Depression to open the storage compartment ⑩ Silent vacuuming mode sensor control ⑪ Turbo vacuuming mode sensor control ⑫ Base sensor control ⑬ Spot vacuuming mode sensor control ⑭ Auto standard vacuuming mode sensor control ⑮ Timer indicator ⑯ Rechargeable battery status indicator ⑰ Side brushes (20 arms and 6 arms, supplied loose) ⑱ Roller brush ⑲ Charging contacts ⑳ Front wheel ㉑ Sensors (toppling protection) ㉒ Roller brush cover ㉓ Drive wheels ㉔ Suction aperture with seal unit ㉕ Back wheel

B - Base station and remote control

Base station

① Cable rewind ② Cable guides ③ Socket for the power supply unit plug (not visible in the illustration) ④ Charging contacts

Remote control

① Power button (switch on and off) ② Base button (direct vacuum cleaner to base station) ③ OK confirmation button with direction buttons around it ④ Start/Pause button (▶II) (start/interrupt vacuuming) ⑤ Mode button (select the vacuuming mode) ⑥ WIFI button (activate/deactivate WiFi) ⑦ Clock button (set time of day) ⑧ Timer button (set the timer) ⑨ Mute button (activate/deactivate acoustic signals) ⑩ Climb button (reduce crossing over height) ⑪ Battery compartment (at the back)

C - Dust box

① Handle ② Cleaning tool with wiper ③ Wiper button ④ Lid ⑤ Release buttons for the lid ⑥ Dust compartment ⑦ Pre-filter ⑧ Exhaust filter ⑨ Exhaust filter compartment lid

Disposing of sales packaging

The packaging material protects the robot vacuum cleaner from transport damage. The packaging materials used are selected from materials which are environmentally friendly for disposal and can therefore be recycled.

Recycling the packaging material reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation.

Disposing of your old appliance

Before disposing of your robot vacuum cleaner, remove the exhaust filter and the pre-filter and dispose of them with your household waste.

Electrical and electronic appliances contain many valuable materials. They also contain certain materials, compounds and components which were essential for their correct functioning and safety. These could be hazardous to human health and to the environment if disposed of with household waste or if handled incorrectly. Please do not, therefore, dispose of your old appliance with household waste.

Instead, please make use of officially designated collection and disposal points to dispose of and recycle electrical and electronic appliances in your local community, with your dealer or with Miele. By law (depending on country), you are solely responsible for deleting any personal data from the old appliance prior to disposal.

Ensure that your old appliance presents no danger to children while being stored for disposal.

Disposing of old batteries

In many cases, electrical and electronic appliances contain batteries which must not be disposed of with household waste after use. You are legally obliged (depending on country) to remove any old batteries which are not securely enclosed by the vacuum cleaner and to take them to a suitable collection point (e.g. retailer) where they can be handed in free of charge. Insulate the metal contacts with adhesive tape to prevent short circuits. Batteries may contain substances which can be hazardous to human health and the environment.

The labelling on the battery will provide further information. The bin symbol with a cross through it means that the batteries must not be disposed of in household waste. A bin with a cross through it which also has one or more chemical symbols on it indicates that the battery contains lead (Pb), cadmium (Cd) and/or mercury (Hg).

Old batteries contain valuable raw materials which can be recycled. Disposing of batteries separately makes them easier to handle and recycle.

Functions and features of the robot vacuum cleaner

The robot vacuum cleaner is suitable for the daily cleaning of hard floors, fitted carpets and short-pile rugs and can also be used on deep-pile rugs.

Please observe the flooring manufacturer's cleaning and care instructions.

The robot vacuum cleaner is fitted with cameras and sensors. It can vacuum all accessible areas efficiently and independently.

Accessories supplied

• Remote control/2 batteries
• 2 universal side brushes with 20 arms (for hard floors, fitted carpets and short-pile rugs)
• 2 carpet side brushes with 6 arms (for deep-pile rugs)
• Power supply unit with plug
• Country-specific power adapter
• Base station and adhesive holder
• Magnetic strip

Connection

Illustrations 1–12 for this section are on the last fold-out page at the end of these operating instructions.

Inserting the side brushes (Fig. 01 + 02)

Place the robot vacuum cleaner upside down on a level, clean surface.

If the area to be vacuumed features hard floors, fitted carpets and short-pile rugs, use the two 20-arm universal side brushes. For deep-pile rugs, the two 6-arm carpet side brushes are more suitable.

Select the appropriate pair of side brushes. Press the two side brushes carefully onto their pins until they audibly engage. Take care to comply with the markings L and R.

Removing the protective foil (Fig. 03)

Remove the protective foil from the base station and from the robot vacuum cleaner display. Remove the protective strip from the depression of the storage compartment.

Placing the batteries in the remote control (Fig. 04)

Observe the instructions regarding the handling of batteries found in the "Safety notes and warnings" section at the beginning of these operating instructions.

Remove the battery compartment cover. Insert the 2 batteries supplied. Make sure the polarity is correct. Close the battery compartment cover.

Switching on the robot vacuum cleaner (Fig. 05)

Press the I/O switch on the side of the robot vacuum cleaner to the I position.

The rechargeable battery status indicator lights up in the control field. The robot vacuum cleaner will switch to standby after approx. 60 seconds. The robot vacuum cleaner is reactivated by pressing any button on the remote control or one of the sensors in the control field.

Connecting the base station (Fig. 06–09)

Observe the instructions regarding the handling of the base station and the power supply unit found in the “Safety notes and warnings” section at the beginning of these operating instructions.

■ Place the base station on a level surface against a free wall within easy access of a power socket. Ensure that there is an obstacle-free distance of at least 1.5 m in front and 0.5 m to the right and left of the base station (Fig. 06). ■ Insert the plug of the supplied power supply unit into the socket at the back of the base station. You can wind excess cable around the cable rewind. Guide the cable through one of the two cable guides (Fig. 07). ■ Insert the country-specific power adapter into the power supply unit until it audibly engages and then plug it into the selected power socket (Fig. 08).

An adhesive holder is included to permanently fix the base station to the floor (Fig. 09).

■ Insert the adhesive holder into the recess provided on the underside of the base station until the adhesive holder clicks into place. ■ Remove the blue protective foil from the adhesive strips. ■ Place the base station in its chosen location and press down firmly on the base station.

You can remove the base station at any time; the adhesive holder remains on the floor. If you want to remove the adhesive holder from the floor, pull on the two pulling-off devices.

Charging the battery (Fig. 10)

The rechargeable battery is supplied not fully charged. Before using for the first time, it must be fully charged while the robot vacuum cleaner is switched on (switch I/O to I).

The battery can also be charged when the robot vacuum cleaner is switched off (switch I/O to 0). In this case, the vacuum cleaner indicators will not react.

■ Connect the robot vacuum cleaner correctly to the charging contacts on the connected base station.

As the rechargeable battery charges, the status indicator flashes in the control field.

The charging process takes up to 3 hours for the Scout RX3 and up to 4 hours for the Scout RX3 Runner and Scout RX3 Home Vision HD. You can then vacuum for up to one

hour with the Scout RX3 and up to 2 hours with the Scout RX3 Runner and Scout RX3 Home Vision HD.

Rechargeable battery status indicator in the control field

Red Charged capacity approx.

0% - 20%

Orange Charged capacity approx.

20% - 50%

Green Charged capacity approx.

50% - 100%

Setting the time of day (Fig. 11)

(also possible via a mobile device, see the "Scout RX app" section)

You can choose between a 24-hour clock and a 12-hour a.m./p.m. clock.

Use the remote control to set the time of day.

■ Briefly press the Clock button.

24h will appear in the display.

■ Press the OK button if you want a 24-hour clock.

■ Press the + button if you want a 12-hour a.m./p.m. clock and confirm 12h with OK.

The hour display flashes in the display.

Press the + or - direction button to set the current hour.

Press the OK button to confirm your selection.

The minute display flashes in the display.

Press the + or - direction button to set the current minutes.

Press the OK button to confirm your selection.

If you want to alter the time of day, proceed as described above. Press the Clock button for 3 seconds.

Defining the area to be vacuumed (Fig. 12)

(also possible via a mobile device, see the "Scout RX app" section)

You can define any areas which the robot vacuum cleaner should not have access to.

The robot vacuum cleaner is 85 mm high.

Any items under which vacuuming is required should have a minimum clearance of 87 mm.

Place the magnetic strip supplied with the groove facing downwards on the floor.

The robot vacuum cleaner will not cross over the magnetic strip.

Adhesive strips are supplied for permanent fixing. Additional magnetic strips are available to order from the Miele webshop.

Use

Always observe the robot vacuum cleaner during the first cleaning session in a new environment and after making changes in your home. Remove any problematic obstacles or section off the relevant areas with the magnetic strip or using the controller on a mobile device (see “Connection” – “Defining the area to be vacuumed”). Check whether steps and drops in height are recognized properly.

Your robot vacuum cleaner is equipped with an integrated WiFi module. You can view status information or execute control commands using a mobile device (tablet PC or smartphone). If you would like to control the robot vacuum cleaner using a mobile device, please read the “Scout RX app” section.

Operation of the robot vacuum cleaner via remote control and the control field is described later in this section.

Switching on and off

■ Press the Power button on the remote control or any sensor in the control field.

Starting vacuuming

There are 2 ways to start vacuuming:

Option 1 (Remote control)

■ Press the ▶|| button.

Option 2 (Control field)

■ Press the ▶ll sensor.

The area to be vacuumed will be cleaned.

The robot vacuum cleaner always cleans for at least 5 minutes, regardless of the size of the surface to be vacuumed.

Finishing vacuuming if vacuuming started from the base station

The robot vacuum cleaner will return to the base station and recharge.

If the battery is low, the robot vacuum cleaner will return to the base station and recharge. This will appear in the display. The robot vacuum cleaner will then continue vacuuming.

Finishing vacuuming if vacuuming started from somewhere in the room

The robot vacuum cleaner will return to its starting point and switch to standby after approximately 60 seconds.

The robot vacuum cleaner will stand still when there is low battery capacity. Charge the robot vacuum cleaner.

Vacuuming manually

You can use the direction buttons on the remote control to vacuum a particular area of the room.

While the robot vacuum cleaner is vacuuming, press and hold one of the direction buttons.

The robot vacuum cleaner will turn in the desired direction until you let go of the direction button.

Press and hold the + direction button.

The robot vacuum cleaner will travel in the desired direction and continue to vacuum.

Press the ▶ll button on the remote control or the ▶ll sensor in the control field.

The original vacuuming process will continue running.

Interrupting vacuuming

Press the ▶II button on the remote control or the ▶II sensor control in the control field.

The robot vacuum cleaner stops.

Press the button or the sensor control again to continue vacuuming.

If you lift the robot vacuum cleaner off the floor during a pause and then place it down somewhere else, rLOC will appear in the display when you activate it again. The robot vacuum cleaner will turn around and compare its new location with its saved map data.

If the data is compatible, the robot vacuum cleaner will start cleaning and not go over surfaces that have already been cleaned.

If the data is not compatible, the robot vacuum cleaner will not move.

rLOC in the display can only be cancelled by pressing the ▶II button or the ▶II sensor control several times.

Manual navigation (without vacuuming)

You can use the direction buttons on the remote control to direct the robot vacuum cleaner to a specific area of the room.

■ Press and hold one of the direction buttons.

The robot vacuum cleaner will travel in the desired direction without vacuuming.

You cannot direct the robot vacuum cleaner manually to the base station in order to recharge it.

Directing the robot vacuum cleaner to the base station

(only possible when vacuuming was started from the base station)

■ Press the Base button on the remote control or the Base sensor in the control field.

The robot vacuum cleaner will travel to the base station and recharge.

Operating modes

There are 5 operating options:

Auto

Standard vacuuming for normally soiled flooring.

Spot Vacuuming of an area approximately 1.8 m x 1.8 m around the selected starting point of the robot vacuum cleaner.

approx. 1.8 m x 1.8 m around the selected starting point of the robot vacuum cleaner.

Directing the robot vacuum cleaner to the base station.

Directing the robot vacuum cleaner to the base station.

For vacuuming lightly soiled flooring with a short vacuuming duration.

For vacuuming lightly soiled flooring with a short vacuuming duration.

Energy-saving vacuuming with low noise development.

Energy-saving vacuuming with low noise development.

■ Press the Power button on the remote control.

There are 2 ways of selecting the operating mode:

There are 2 ways of selecting the operating mode:

Option 1 (remote control)

Press the Mode button repeatedly until the symbol for the operating mode you want lights up in the control field.

Press the ▶ll button to start vacuuming.

Option 2 (control field)

Press the sensor control for the operating mode you want to use.

Press the ▶II sensor control to start vacuuming.

Quitting the current operating mode

Press the Power button on the remote control or the ▶II sensor in the control field for at least 3 seconds.

The robot vacuum cleaner will switch to standby after approx. 60 seconds.

You can switch the robot vacuum cleaner to standby before 60 seconds is up by pressing the Power button again.

The robot vacuum cleaner is reactivated by pressing any button on the remote control or one of the sensors in the control field.

Setting the timer

(only possible if the clock has been set)

If you would like the robot vacuum cleaner to start at the same time every day, you can save the start time and the operating mode you want to memory.

The robot vacuum cleaner can also vacuum in the dark. However, please be aware that vacuuming may be less thorough. The cameras require light in order to navigate unobstructed.

Use the remote control to set the timer.

Press the Timer button briefly.

The timer ⏻ indicator flashes in the control field and the hour display flashes in the display.

Press the + or - direction button to set the hour you want.

Press the OK button to confirm your selection.

The timer ⏻ indicator flashes in the control field and the minute display flashes in the display.

Press the + or - direction button to set the minutes you want.

Press the OK button to confirm your selection.

Press the Mode button repeatedly until the symbol for the operating mode you want flashes in the control field.

Press the OK button to confirm your selection.

The settings are shown for approx. 3 seconds in the control field. The robot vacuum cleaner will now start to vacuum at the same time each day.

If the timer ⏻ indicator is lit up in the control field, the timer is activated.

To alter the entries, proceed as described above. Then press the Timer button for 3 seconds.

Tip: you can save up to 7 individual "start time – operating mode" combinations if you set the timer using a mobile device, see section "Scout RX app".

Please note that the robot vacuum cleaner always follows the save commands which were set most recently, regardless of whether the settings were configured using the remote control, control unit or with a mobile device.

Deactivating the timer

Briefly press the Timer button on the remote control.

The Timer ⏻ indicator goes out in the control field.

Activating the timer/displaying a set start time

Briefly press the Timer button on the remote control.

The timer ⏻ indicator lights up in the control field and the set start time is shown briefly in the display. The robot vacuum cleaner will start to vacuum at the set time.

Deactivating the acoustic signals

Acoustic signals are set as standard. You can deactivate and then reactivate them.

Briefly press the Mute button on the remote control.

OFF will appear in the display briefly.

Acoustic signals for error messages cannot be deactivated.

Reducing the maximum crossing over height

The robot vacuum cleaner is set to overcome height differences of up to 17 mm as standard. It is therefore able to vacuum carpets, move over door thresholds, etc.

If you would like to reduce this height (down to approx. 6 mm) in order to protect the legs of chairs, tables or lamps, for example, you can deactivate the factory default setting.

Briefly press the Climb button on the remote control.

LO will appear in the display.

Press the Climb button again briefly if you want to reactivate the maximum crossing over height of 17 mm. HI will appear in the display.

"Scout RX" app

WiFi

Please note that, despite the manufacturer's extremely high security standards, there may be data security risks for the user whenever networked appliances are used. For this reason, we offer you the option of removing the WiFi module from the robot vacuum cleaner. You can find instructions for this at the end of this section.

You can view status information or execute control commands using a mobile device (tablet PC or smartphone).

The robot vacuum cleaner is equipped with an integrated WiFi module for this purpose.

Make sure that you have sufficient signal strength for your WiFi network in the rooms where the robot vacuum cleaner will be vacuuming.

You can download the "Scout RX" app for free via the Apple App Store® or Google Play Store™.

■ Download the app from one of the app stores.

For data protection reasons, you have to connect each mobile device to the robot vacuum cleaner individually.

Activating the network function of the robot vacuum cleaner

In order to connect your robot vacuum cleaner to your WiFi network, you must first activate the network function. The network function is deactivated as standard.

There are 2 ways to activate the network function:

Option 1 (remote control)

■ Press the WIFI button.

The WiFi ✦ indicator lights up in the control field.

Option 2 (control field)

Press the Base sensor control for at least 2 seconds.

The WiFi ✦ indicator lights up in the control field.

Start the app and set up a Miele user account.

You can connect your mobile device directly to the robot vacuum cleaner or connect via your WiFi network.

Note for dealers

You can connect the robot vacuum cleaner directly to a mobile device without a WiFi network.

To do this, connect the mobile device to the robot vacuum cleaner's WiFi. Use the robot vacuum cleaner's serial number as the WiFi password. You can find the serial number on a sticker in the storage compartment and on the data plate on the underside of the robot vacuum cleaner. Follow the instructions in the app.

Follow the user navigation instructions in the app.

Please note that the robot vacuum cleaner always follows the save commands which were set most recently, regardless of whether the settings were configured using the remote control, control field or with a mobile device.

Video function

(for Scout RX3 Home Vision HD, use the "Scout RX" app)

The camera on the right at the front of the robot vacuum cleaner sends encrypted images in real time to the selected mobile device. Transmission quality is dependent upon the speed of the Internet connection in your home and the speed of your mobile device.

The video function indicator in the control field flashes red when images are being sent.

The live video is only played back in the Miele app; it is not saved.

The privacy and personal living space of third parties must be respected when using the video function. The robot vacuum cleaner with video function should therefore only be used in your own home. Anyone else present should be informed before you start to use the video function.

We recommend cleaning both cameras regularly with a soft, dry cloth.

Removing the WiFi module

Press the depression at the top of the robot vacuum cleaner.

The lid of the storage compartment will open.

Unlatch the dust box by lifting the handle upwards. Remove the dust box.

Pull the cover out from the front. Remove the WiFi module. Put the cover back on.

Maintenance

Risk of injury caused by rotating roller brush.

The robot vacuum cleaner may start without warning while maintenance work is being carried out.

Switch the robot vacuum cleaner off before doing any maintenance work. To switch it off, press the I/O switch on the side of the robot vacuum cleaner to the 0 position.

We recommend using only genuine Miele accessories bearing the "ORIGINAL Miele" logo on the packaging. Only these will guarantee optimum suction power for your robot vacuum cleaner and the best possible cleaning results.

Please note that faults and damage caused by use of accessories which do not bear the "ORIGINAL Miele" logo on their packaging are not covered by the robot vacuum cleaner warranty.

Purchasing accessories

Original Miele accessories are available from the Miele Webshop, Miele Customer Service and your Miele supplier.

Original Miele accessories are identified by the "ORIGINAL Miele" logo on the packaging.

Emptying the dust box

Empty the dust box of the robot vacuum cleaner after each use in order to achieve the best possible cleaning results.

At the very latest, you must empty the dust box when "I__I" appears in the display running from bottom to top.

The contents of the dust box can be disposed of with normal domestic waste, providing they consist of general household dust only.

Press the depression at the top of the robot vacuum cleaner.

The lid of the storage compartment will open.

Unlatch the dust box by lifting the handle upwards.

Remove the dust box.

Press one or both release buttons in the direction of the arrow and remove the dust box lid.

Empty the dust box.

Refit the lid and close the dust box, making sure it clicks into place. Place the dust box into the robot vacuum cleaner with the handle lifted up and latch it into place by pushing the handle back down. Close the storage compartment lid and press down on the depression in order to lock it.

Cleaning the dust box

Clean the dust box as required.

A cleaning tool is located at the top of the dust box lid.

Remove the cleaning tool.

Clean the dust box and the underside of the lid using the cleaning tool.

Cleaning the exhaust filter

Clean the exhaust filter as required.

The exhaust filter compartment is located in the dust box.

Remove the lid from the dust box.

Fold out the filter unit from the dust box.

Remove the pre-filter and clean it as required using the cleaning tool.

Release the exhaust filter and clean it using the cleaning tool. Refit the exhaust filter into the cover. Place the pre-filter onto the exhaust filter.

The filter unit is complete.

Carefully refit the filter unit on the dust box and clip the filter unit into position.

The exhaust filter must be replaced with a new one after approx. 6 months in order to achieve the best possible cleaning results.

Cleaning the side brushes

Clean the side brushes as required. For this you will require the cleaning tool which is located at the top of the dust box lid.

Place the robot vacuum cleaner upside down on a level, clean surface.

20-arm universal side brushes: take hold of opposing side brushes (one long and one short bunch per hand) and pull them upwards to remove them.

6-arm carpet side brushes: take hold of opposing elastic side brush holders (one holder per hand) and pull them upwards to remove them. Remove threads and hair using the wiper which is located on the bottom of the cleaning tool. Hold the wiper over a bin.

Press the button at the top of the wiper several times until all threads and hair have fallen out.

Press the two cleaned side brushes carefully onto their pins until they audibly engage. Take care to comply with the markings L and R.

In order to continue to achieve the best possible cleaning results, replace the pair of side brushes after approx. 1 year.

Cleaning the roller brush

Clean the roller brush as required. For this, you will require the cleaning tool which is located at the top of the dust box lid.

Place the robot vacuum cleaner upside down on a level, clean surface. Remove both side brushes, see "Cleaning the side brushes".

Release the roller brush cover and remove the cover.

Remove the roller brush.

Pull the bearing cover off the roller brush and remove any threads or hairs that have wound themselves around the bearing. Refit the bearing cover, making sure it clicks into position.

Cut any threads or hairs that have wound themselves around the roller brush with a pair of scissors.

Remove the threads and hair using the wiper which is located on the bottom of the cleaning tool. Hold the wiper over a bin.

Press the button at the top of the wiper several times until all threads and hair have fallen out.

Refit the roller brush with the bearing cover attached. Make sure that the side with the pointed end is inserted into the corresponding slot.

Carefully refit the roller brush cover on both sides, making sure it clicks into position. Refit the side brushes, see “Cleaning the side brushes”.

In order to continue to achieve the best possible cleaning results, replace the roller brush with a new one after approx. 1 year.

Cleaning the dust box seals

Clean the seals on the bottom of the dust box as required.

Place the robot vacuum cleaner upside down on a level, clean surface.

Wipe the seals with a slightly damp cloth to clean them.

In order to continue to achieve the best possible cleaning results, replace the seal unit with a new one after approx. 1 year.

Replacing the seal unit on the dust box

Remove the dust box.

Unlatch the seal unit from the underside of the dust box so that the arrow points to the 🔓 symbol. Remove the seal unit. Insert the new seal unit so that the arrow points to the 🔍 symbol. Lock the seal unit, making sure it clicks into position.

The arrow points to the 🔒 symbol.

Cleaning the front wheel

Clean the front wheel as required. For this you will require the cleaning tool which is located at the top of the dust box lid.

Place the robot vacuum cleaner upside down on a level, clean surface.

■ Unclip the cover. ■ Remove the front wheel.

■ Remove any threads and hair and clean the front wheel, the cover and the slot depression using the cleaning tool. ■ Refit the front wheel and close the cover making sure it clicks into position.

Cleaning the sensors

Clean the sensors as required.

■ Place the robot vacuum cleaner upside down on a level, clean surface.

■ Clean the sensors carefully using a dry cotton wool bud.

⚠️ Keep batteries out of the reach of children.

A swallowed battery can cause injury and even death. Even flat batteries can still be dangerous. If you suspect a child has swallowed a battery, seek medical advice immediately*. Examine devices and make sure the battery compartment is correctly secured, e.g. that the screw or other mechanical fastener is tightened. Do not use if compartment is not secure.

* Australia: Poisons Information Centre, Tel. 13 11 26;

NZ: National Poisons Centre, Tel. [phone]

Replacing batteries in the remote control

2 batteries (AAA, 1.5 V) are required.

Observe the instructions regarding the handling and disposal of batteries found in the “Safety notes and warnings” and “Caring for the environment” sections at the beginning of these operating instructions.

■ Remove the battery compartment cover. ■ Replace the batteries. Make sure the polarity is correct. ■ Close the battery compartment cover.

Replacing the rechargeable battery

An original Miele lithium-ion rechargeable battery is required:

• YCR-M05 for Scout RX3
• YCR-MT12 for Scout RX3 Runner and Scout RX3 Home Vision HD

The rechargeable battery compartment is located in the robot vacuum cleaner's storage compartment.

Observe the instructions regarding the handling and disposal of rechargeable batteries found in the “Safety notes and warnings” and “Caring for the environment” sections at the beginning of these operating instructions.

Open the storage compartment. Remove the dust box.

Open the rechargeable battery compartment by unlatching the cover upwards.

Scout RX3 (YCR-M05)

Carefully pull the cables so that the plug connection is pulled out of the slot. Press the latch on the plug connection in order to release the plug. Remove the rechargeable battery.

Insert the plug of the new rechargeable battery into the counterpart, making sure it clicks into place. Insert the rechargeable battery carefully, making sure it is properly positioned (see right-hand side of picture). Store the plug connection in the slot at the side.

Carefully refit the cover of the rechargeable battery compartment and close it, making sure it clicks into place.

Scout RX3 Runner and Scout RX3 Home Vision HD (YCR-MT12)

Carefully remove the rechargeable battery using the tab until the plug connection is exposed. Press the latch on the plug connection in order to release the plug.

Insert the plug of the new rechargeable battery into the counterpart, making sure it clicks into place. Store the plug connection in the side recess. Insert the rechargeable battery carefully, making sure it is properly positioned (see right-hand side of picture).

Carefully refit the cover of the rechargeable battery compartment and close it, making sure it clicks into place.

Cleaning and care

Risk of injury caused by rotating brush.

The robot vacuum cleaner may start without warning while maintenance work is being carried out.

Switch the robot vacuum cleaner off before doing any maintenance work. To switch it off, press the I/O switch on the side of the robot vacuum cleaner to the 0 position.

Robot vacuum cleaner and accessories

Risk of electric shock from mains voltage.

If moisture gets into the robot vacuum cleaner and accessories, there is a risk of electric shock.

Do not immerse the robot vacuum cleaner or any accessories supplied with it in water.

Observe the special cleaning instructions in the “Maintenance” section.

Clean the robot vacuum cleaner and all plastic accessories with a commercially available cleaner suitable for plastic.

Static charge can cause a build-up of dust on the robot vacuum cleaner. This should be removed using a soft, dry cloth.

Damage due to unsuitable cleaning agents.

All surfaces are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolour the external surfaces.

Do not use abrasive cleaning agents, glass cleaning agents, all-purpose cleaners or oil-based conditioning agents.

Storage/Factory default settings

Storage

Switch the robot vacuum cleaner off if it is not going to be used for an extended period of time. To switch it off, press the I/O switch on the side of the robot vacuum cleaner to the 0 position.

If the robot vacuum cleaner is not going to be used for an extended period of time, make sure it is stored in a well ventilated, cool place, but not at an ambient temperature below 0 °C.

For optimum care, store the robot vacuum cleaner at half charge capacity (rechargeable battery status indicator in the control field is orange).

Standard settings

The robot vacuum cleaner can be reset to its factory default settings. Have the remote control to hand.

■ Press and hold the Spot and Turbo sensors in the control field at the same time for at least 5 seconds.

r:St will appear in the display.

■ Within the next 2 seconds, press the OK button on the remote control until F:tr appears in the display.

The robot vacuum cleaner will start again with its factory default settings restored.

Service

Contact in case of malfunction

In the event of any faults which you cannot remedy yourself, please contact your Miele Dealer or Miele Service.

Contact information for Miele Service can be found at the end of this document.

Please note that telephone calls may be monitored and recorded for training purposes and that a call-out charge will be applied to service visits where the problem could have been resolved as described in this booklet.

Warranty

For information on the appliance warranty specific to your country, please contact Miele. See back cover for address.

In the UK, your appliance warranty is valid for 2 years from the date of purchase. However, you must activate your cover by calling 0330 160 6640 or registering online at www.miele.co.uk.

Problem solving guide

Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed.

The following guide may help you to find the reason for a malfunction or a fault, and to correct it.

Risk of injury caused by rotating roller brush.

The robot vacuum cleaner may start without warning while problems are being dealt with.

Switch the robot vacuum cleaner off before dealing with any problems. To switch it off, press the I/O switch on the side of the robot vacuum cleaner to the 0 position.

Problem Cause and remedy
The cleaning performance is poor.	The dust box is full.■ Empty and clean the dust box.
	The roller brush is dirty or worn out.■ Clean the roller brush.■ Replace the roller brush.
	The seals on the dust box are dirty or worn out.■ Clean the seals and the suction channel between them.■ Replace the seal unit.■ Check whether the roller brush cover is fitted properly and is locked into place on both sides, see “Maintenance” – “Cleaning the roller brush”.
	The exhaust filter is dirty.■ Clean the exhaust filter.■ Replace the exhaust filter.
	The side brushes have worn out.■ Replace the side brushes.
The robot vacuum cleaner switches itself off after it has been switched on using the Power button.	The rechargeable battery is not sufficiently charged.■ Connect the robot vacuum cleaner correctly to the charging contacts on the connected base station.
Problem Cause and remedy
The robot vacuum cleaner does not return to the base station after vacuuming.	It had started vacuuming from somewhere in the room.■ The robot vacuum cleaner will return to its starting point.
	There is insufficient light for the robot vacuum cleaner to navigate.■ Provide sufficient lighting.
	The base station is not connected correctly.■ Connect the base station exactly as described in these operating instructions, see section “Connection” – “Connecting the base station”.
	The signal between the infrared transmitter on the base station and the robot vacuum cleaner is broken.■ Clean the front of the base station and the front of the robot vacuum cleaner carefully with a soft, dry cloth and make sure that no items disrupt the signal.
	Obstacles on the floor which is to be vacuumed can impede navigation.■ Watch the robot vacuum cleaner during vacuuming.■ Remove any problematic obstacles.■ Section off the problematic area with the magnetic strip.■ Reduce the robot vacuum cleaner’s maximum crossing over height, see section “Use” – “Reducing the maximum crossing over height”.
The robot vacuum cleaner is not charging.	The base station is not connected correctly.■ Connect the base station exactly as described in these operating instructions, see section “Connection” – “Connecting the base station”.
Problem Cause and remedy
The robot vacuum cleaner does not react.	The robot vacuum cleaner is switched off.■ Switch it on (press I/0 to I).
	The batteries in the remote control have been inserted incorrectly.■ Take care with the polarity.
	The batteries in the remote control are dead.■ Exchange the batteries.
	The signal between the infrared transmitter on the vacuum cleaner and the remote control is broken.■ Clean the front of the robot vacuum cleaner and the top of the remote control carefully with a soft, dry cloth and make sure that no items disrupt the signal.
	The remote control is too close to the robot vacuum cleaner or too far away from it.■ Increase or decrease the distance and when using the remote control, direct it towards the robot vacuum cleaner.
“I_ _I” appears in the display running from bottom to top.	The dust box is full.■ Empty and clean the dust box.
rLOC appears in the display.	Vacuuming was interrupted; the robot vacuum cleaner was moved during the pause.■ Proceed as described in “Use” – “Interrupting vacuuming”.

Error messages

Risk of injury caused by rotating roller brush.

The robot vacuum cleaner may start without warning while errors are being dealt with.

Switch the robot vacuum cleaner off before dealing with any errors. To switch it off, press the I/O switch on the side of the robot vacuum cleaner to the 0 position.

Fault messages are shown in the display.

Your robot vacuum cleaner is supplied with a sticker that lists all error messages.

You can stick this sticker to the underside of the storage compartment lid.

Problem Cause and remedy
F 1 Error “Wheel raised”	■ Place the robot vacuum cleaner on a level floor surface.
F 2 Error “Dirty sensors”	■ Clean the sensors. This error message is also shown when you start up the robot vacuum cleaner and the collision sensor is located above empty space. Remove the robot vacuum cleaner from the edge.
F 3 Error “Filter not recognised”	■ Insert the dust box into the robot vacuum cleaner with an exhaust filter inserted.
F 4 Error “Drive wheels overloaded”	■ Check whether the drive wheels have become dirty. Remove any threads or hair. This error message is also shown if the robot vacuum cleaner is stuck.
F 5 Error “Brushes overloaded”	■ Check whether the roller brush and the side brushes have become dirty. Clean the roller brush and side brushes. This error message is also shown if objects become caught in the robot vacuum cleaner.
F 6 Error “Fan motor overloaded”■ Empty and clean the dust box. Clean or replace the exhaust filter.
F 7 Internal system error or error “Robot vacuum cleaner outside of its permitted ambient operating temperature”■ Switch the robot vacuum cleaner off and on again (I/O switch).
F 8 Error “Front wheel dirty”■ Check whether the front wheel, the cover or the slot recess have become dirty. Remove any threads and hair, and clean the front wheel, the cover and the recess.
Resetting the error message after fixing the problem	You can reset the error messages described above in the following ways
	- Switch the robot vacuum cleaner off and on again (I/O switch).
	- Press the Power button on the remote control.
	- Press the ▶II sensor in the control field of the robot vacuum cleaner for at least three seconds.

Technical data

(for the WiFi module Europe)

Frequency band 2.412 GHz - 2.472 GHz

Maximum transmitting power < 100 mW

Conformity declaration

Miele hereby declares that this robot vacuum cleaner complies with Directive 2014/53/EU.

The complete text of the EU declaration of conformity is available from one of the following internet addresses:

• Products, Download from www.miele.co.uk
• For service, information, operating instructions etc: go to www.miele.co.uk/domestic/customer-information-385.htm and enter the name of the product or the serial number

Copyright and licences

For the purpose of operating and controlling the robot vacuum cleaner, Miele uses proprietary or third-party software that is not covered by open source licensing terms. These items of software/software components are protected by copyright. The copyright powers of Miele and third parties must be respected.

In addition, the robot vacuum cleaner contains software components which are distributed under open source licensing terms. The open source components contained in the appliance along with the corresponding copyright notices, copies of the licensing terms valid at the time and any further information can be accessed locally by IP via a web browser (http:// /Licenses). The liability and warranty arrangements for the open source licences displayed at this location only apply in relation to the respective rights holders.

In particular, the robot vacuum cleaner contains software components licenced by the copyright holders under the GNU General Public License, Version 2, or the GNU Lesser General Public License, Version 2.1. For a period of at least 3 years from the date of purchase or delivery of the robot vacuum cleaner respectively, Miele offers to provide you or third parties with a machine-readable copy of the source code of the Open Source components contained in the robot vacuum cleaner and licenced under the terms of the GNU General Public License, Version 2, or the GNU Lesser General Public License, Version 2.1, on a data carrier (CD-ROM, DVD or USB stick). To obtain this source code, please contact us via e-mail ([e-mail]) or the postal address below quoting the product name, the serial number and the date of purchase.

Miele & Cie. KG

Open Source

GTZ/TIM

Please note the limited warranty in favour of the rights holders under the terms of the GNU General Public License, Version 2 and the GNU Lesser General Public License, Version 2.1:

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

You can obtain detailed instructions for the use of test modes from the Miele Customer Service Department.

Electrical connection for the UK

All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). The voltage and frequency are given on the data plate located underneath the vacuum cleaner. Please ensure that these match the household mains supply. The fuse rating is quoted on the plug. The appliance is supplied with a cable and moulded plug ready for connection to a 230-240 V/50 Hz a.c. single phase supply.

Electrical connection AU, NZ

All work should be carried out by a suitably qualified and competent person in strict accordance with national and local safety regulations. The voltage and rated load are given on the data plate located underneath the vacuum cleaner. Please ensure that these match the household mains supply. The appliance is supplied with a cable and moulded plug ready for connection to a 230V/50Hz AC single phase supply.

Test Marks Electrical safety RCM Mark

Electrically suppressed according to

AS/NZS CISPR 14.1

Ladestation aktiveres (fjernbetjening)

Fejlmeldinger

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

Error messages

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

Error messages

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

Error messages

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

Error messages

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

Error messages

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

To the base unit (FK)

Select function (control panel)

Auto

Error messages

This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY, without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License and GNU Lesser General Public License for more details.

United Kingdom

Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW

Tel: [phone], Internet: www.miele.co.uk/service, E-mail: [e-mail]

Australia

Miele Australia Pty. Ltd.

ACN 005 635 398

ABN 96 005 635 398

1 Gilbert Park Drive

Knoxfield, VIC 3180

Tel: [phone]

Internet: www.miele.com.au

China Mainland

Miele Electrical Appliances Co., Ltd.

1-3 Floor, No. 82 Shi Men Yi Road

Jing' an District

200040 Shanghai, PRC

Tel: [phone]

Fax: [phone]

E-mail: [e-mail],

Kowloon Bay, Hong Kong

Tel: [phone]

Fax: [phone]

Email:

[e-mail]

Website: www.miele.hk

India

Miele India Pvt. Ltd.

1st Floor, Copia Corporate Suites,

Commercial Plot 9,

Mathura Road, Jasola,

New Delhi - 110025

E-mail: [e-mail]

Website: www.miele.in

Ireland

Miele Ireland Ltd.

2024 Bianconi Avenue

Citywest Business Campus

Dublin 24

Tel: [phone]

Fax: [phone]

E-Mail: [e-mail]

Internet: www.miele.ie

Malaysia

Miele Sdn Bhd

Suite 12-2, Level 12

Menara Sapura Kencana

Petroleum

Solaris Dutamas No. 1

Jalan Dutamas 1

50480 Kuala Lumpur, Malaysia

Phone: [phone]

Fax: [phone]

New Zealand

Miele New Zealand Limited

IRD 98 463 631

8 College Hill

Freemans Bay, Auckland 1011

New Zealand

Tel: [phone]

Internet: www.miele.co.nz

Singapore

Miele Pte. Ltd.

29 Media Circle

11-04 ALICE@Mediapolis

Singapore 138565

Tel: [phone]

Fax: [phone]

E-Mail: [e-mail]

Internet: www.miele.sg

South Africa

Miele (Pty) Ltd.

63 Peter Place

Bryanston 2194

P.O. Box 69434

Bryanston 2021

Tel: [phone]

Fax: [phone]

E-mail: [e-mail]

Internet: www.miele.co.za

Thailand

Miele Appliances Ltd.

BHIRAJ TOWER at EmQuartier

43rd Floor Unit 4301-4303

689 Sukhumvit Road

North Klongton Sub-District

Vadhana District

Bangkok 10110, Thailand

United Arab Emirates

Miele Appliances Ltd.

Showroom 1

Eiffel 1 Building

Sheikh Zayed Road, Umm Al She

P.O. Box 114782 - Dubai

Tel. [phone]

Fax. [phone]

800-MIELE (64353)