EY74A2X - Drill PANASONIC - Free user manual and instructions

Product type	Cordless hammer drill
Brand	Panasonic
Model	EY74A2X
Rated voltage	14.4 V
Battery type	Lithium-ion
Battery capacity	2.0 Ah
No-load speed	0 - 600 rpm (1st speed) / 0 - 2000 rpm (2nd speed)
Max torque	30 Nm
Chuck	Keyless, 1.5 - 13 mm
Max drilling diameter (wood)	38 mm
Max drilling diameter (steel)	13 mm
Max drilling diameter (concrete)	10 mm
Weight (with battery)	1.6 kg
Dimensions (L x W x H)	250 x 70 x 230 mm
Power supply	Rechargeable Li-ion battery
Main functions	Drilling, screwdriving, hammering
Maintenance and cleaning	Clean with a dry cloth; do not use solvents
Safety	Chuck brake, spindle lock, electronic speed control
Spare parts and repairability	Battery, charger, carbon brushes, chuck available
General information	2-year warranty, made in Japan

Frequently Asked Questions - EY74A2X PANASONIC

How to change the chuck of the Panasonic EY74A2X drill?

To change the chuck, insert an Allen key into the fixing screw inside the chuck and turn it counterclockwise. Then unscrew the chuck by hand.

Which battery is compatible with the EY74A2X model?

This model uses a Panasonic 14.4 V lithium-ion battery from the EY range. Compatible references include EY9L21B or EY9L22B.

How to adjust the torque setting?

Turn the torque adjustment ring located behind the chuck. The numbers indicate the torque level, from lowest (1) to highest (20+). For drilling, set the ring to the drill symbol.

The drill no longer starts, what to do?

First check that the battery is charged and properly engaged. If the problem persists, clean the battery and tool contacts. If nothing works, contact customer service.

How to use the hammer function?

To activate hammering, slide the mode selector to the hammer symbol. This function is ideal for drilling brick or concrete.

What is the rotation speed in first gear?

In first gear, the no-load speed is 0 to 600 rpm, suitable for screwdriving or drilling large diameters.

How to maintain the drill?

Clean the tool regularly with a dry cloth. The ventilation openings must be clear. Do not use chemicals. The motor carbon brushes should be checked every 200 hours of use.

Can I use SDS bits?

No, the EY74A2X chuck is a standard keyless chuck accepting cylindrical shanks from 1.5 to 13 mm. SDS bits require a specific adapter not provided.

How long does the battery charge take?

With the original charger, a 2.0 Ah battery fully charges in about 30 minutes. A 3.0 Ah battery takes 45 minutes.

Does the drill have an LED light function?

Yes, the EY74A2X is equipped with an integrated LED above the chuck. It lights up automatically when you press the trigger to illuminate the work area.

USER MANUAL EY74A2X PANASONIC

Pictured: EY74A2

Before operating this unit, please read these instructions completely and save this manual for future use.

NOTE: Not all battery packs display the alignment mark (Q).

Attaching

Attaching

Connecting

Connecting

Attaching

Coupling

Mounting

Mounting

Mounting

Attaching

Inserting

Mounting

Installation

Connection

Removing

Removal

Removal

Removal

Removal

Removal

Removal

Removal

Removal

Removal

Removal

Removal

Removal

Removal

[Fig.8]

[Fig.9]

Pack cover

Battery cover

Battery cover

battery pack cover

Battery pack cover

Battery cover

Battery cover

Battery cover

Battery cover

Battery cover

Battery pack cover

Battery pack cover

Battery cover

Block cover

Battery unit cover

Battery unit cover

Label (red or yellow)

Label (red or yellow)

Label (red or yellow)

Battery pack release button

Alignment marks

Original instructions: English Translation of the original instructions: Other languages

Read the "Safety Instructions" booklet and the following before using.

I. INTENDED USE

These tools can be used to tighten screws in clutch mode and to drill holes in wood and metal in drill mode. Additionally, model EY79A2 can be used to drill holes in soft concrete and similar materials in hammer mode.

II. ADDITIONAL SAFETY RULES

1) If the bit becomes jammed, immediately turn the trigger switch off to prevent an overload, which can damage the battery pack or motor. Use reverse motion to loosen jammed bits. 2) Do NOT operate Forward/Reverse lever when the trigger switch is on. The battery will discharge rapidly and damage to the main unit may occur. 3) During charging, the charger may become slightly warm. This is normal. Do NOT charge the battery for a long period. 4) Do not strain the tool by holding the speed control trigger halfway (speed control mode) so that the motor stops. 5) To prevent injury during use, hold the tool steady at all times and avoid waving it around. 6) Ensure that there are no hidden gas or water pipes in the area in which you will be working. Contact with hidden pipes or wires could cause electric shock or water or gas leaks. 7) Make sure to hold the object you are working on steady. 8) Check for damaged parts. - Check thoroughly for damage to the protective cover and other parts before operating.

• Check to make sure the tool and all of its functions are working properly.
• Check the adjustment of all movable parts, and check all fixed parts to make sure they are fitted properly and free of damage. Check all parts of the tool for abnormal function.

9) When attempting to repair the protective cover or other parts, please follow the instructions in the user manual. In cases where there are no instructions in the manual, please take it back to the store to have it repaired.

10) If the tool gets exceptionally hot during use, please take it in for service and repair. 11) To avoid potential injury, keep face and hands away from the drill bit and any shavings. 12) Do not wear gloves when operating the tool, as they may get caught by the drill, leading to injury. 13) Battery terminals, screw shavings, and tool accessories such as drill bits will be very hot immediately after operation. Do not touch them as there is a risk of burning yourself.

Symbol Meaning
V	Volts
---	Direct current
n0	No load speed
... min-1	Revolutions or reciprocations per minutes
Ah	Electrical capacity of battery pack
	Rotation only
(EY79A2 only)	Rotation with hammering
	Read the operating instructions before use.
	For indoor use only.

WARNING

• Do not use other than the Panasonic battery packs that are designed for use with this rechargeable tool.
• Panasonic is not responsible for any damage or accident caused by the use of recycled or counterfeit battery pack.
• Do not dispose of the battery pack in a fire, or expose it to excessive heat.
• Do not allow metal objects to touch the battery pack terminals.
• Do not carry or store the battery pack in the same container as nails or similar metal objects.
• Do not charge the battery pack in a high-temperature location, such as next to a fire or in direct sunlight. Otherwise, the battery may overheat, catch fire, or explode. • After removing the battery pack from the tool or the charger, always reattach the pack cover. Otherwise, the battery contacts could be shorted, leading to a risk of fire.
• When the Battery Pack Has Deteriorated, Replace It with a New One. Continued use of a damaged battery pack may result in heat generation, ignition or battery rupture. • To prevent leakage, overheating, smoke generation, fire, and rupturing from occurring, follow these instructions when handling our rechargeable power tools (tool main body/battery pack/charger).

- Do not allow material cuttings or dust to fall onto the battery pack.

- Before storing, remove any material cuttings and dust from the battery pack, fit the red plastic "terminal cover", then place it separately from metal objects (screws, nails, etc.) in the tool case.

Damage caused by loose objects in the case will not be covered by warranty.

- Do not handle the rechargeable power tools in the following way.

(There is a hazard of smoke generation, fire, and rupturing)

• Use or leave in places exposed to rain or moisture
• Use submerging in water

III. ASSEMBLY

Attaching or Removing Bit NOTE:

When attaching or removing a bit, disconnect the battery pack from the main unit or place the switch in the center position (switch lock).

The main unit is equipped with a keyless drill chuck.

1. Attachment

Insert the bit and turn the lock collar clockwise (looking from the front) to tighten firmly until it stops clicking.

[Fig.1]

1. Removal

Turn the lock collar counterclockwise (looking from the front), then remove the bit. [Fig.2]

NOTE:

If there is excessive play in the chuck, secure the drill in place and open the chuck jaws by turning the lock collar and tighten the screw (left-handed screw) with a screwdriver by turning it counterclockwise (viewed from the front). [Fig.3]

Attaching or Removing Battery Pack

NOTE:

When the battery pack is removed from the main unit, the control panel lamp may light up briefly. This is not a malfunction.

1. To attach the battery pack: [Fig.4] Align the highlighted marker points and attach battery pack.

Slide the battery pack until it locks into position.

1. To remove the battery pack: [Fig.4]

Push the button and slide the battery pack forward.

IV. OPERATION

WARNING!

- Do not inhale smoke emitted from the main unit or battery pack as it may be harmful.

[Main Unit]

CAUTION

When storing or carrying the tool, set the Forward/Reverse lever to the center position (switch lock).

NOTE:

Exercise caution to ensure no objects come into contact with the tool's trigger switch.

If an object comes into contact with the tool's trigger switch, even while the Forward/Reverse lever is in the center position (locked), a small amount of electric current may continue flowing, which may cause an excessive discharge from the battery pack and subsequent battery pack failure.

Switch and Forward/Reverse Lever Operation [Fig.5]

1. Push the lever for forward or reverse rotation. Check the direction of the lever before using.
2. Depress the trigger switch slightly to start the tool slowly.
3. Speed will increase by pressing the trigger. The tool stops working immediately by releasing the trigger.
4. When done with an application, lock the switch by centering the lever.

NOTE:

When the brake operates, a braking sound may be heard. This is normal.

CAUTION:

When operating the tool by pulling the trigger, there may be a momentary lag before rotation starts. This does not signal a malfunction.

* This lag occurs as the tool's circuitry starts up when the trigger is pulled for the first time after installing a battery pack or after the tool has not been used for at least 1 minute (or at least 5 minutes when the LED is on). Rotation will start without any lag during second and subsequent operations.

CAUTION:

To prevent damage, do not operate Forward/Reverse lever until the bit comes to a complete stop.

Clutch Torque Setting

Adjust the torque to one of the 18 clutch settings or the “☐” position (TEY79A2 only).

CAUTION:

• Set the clutch setting at this mark [Fig.6] before actual operation.
• If the clutch handle cannot be set to "drilling" mode after driving with clutch function, set the clutch handle to position 1 and operate the clutch for a second.

Speed Selection

Choose a low or high speed to suit the use. [Fig.7]

The more the variable speed control trigger is pulled, the higher the speed becomes.

CAUTION:

• Check the speed selector switch before use.
• Use in low gear when high torque is required in operation. (Using in high gear with high load can cause motor overload and possible failure.) • To prevent excessive temperature increase of the tool surface, do not operate the tool continuously using two or more battery packs. The tool needs cool-off time before switching to another pack.
• Ensure that air vents on the sides of the main unit are not blocked during operation. Covering them can cause the tool to overheat and motor damage to occur.
• Do NOT strain the tool (motor). This may cause damage to the tool.
• Avoid contact with air from vent holes during operation as under heavy load this can become hot and potentially cause injury.

EN

EN

Speed Control Function

Setting the maximum speed.

1. Press the speed setting button and select a speed. The speed changes to H, M, L and OFF (the light is off) in this order.
2. Select OFF to release it.

Display Low mode High mode
H Approx. 300 min	-1 (rpm) Approx. 1000 min	-1 (rpm)
M Approx. 200 min	-1 (rpm) Approx. 670 min	-1 (rpm)
L Approx. 150 min	-1 (rpm) Approx. 500 min	-1 (rpm)
OFF Ordinary speed	18 V Approx. 470 min -1 (rpm)	Ordinary speed
	14.4 V Approx. 400 min -1 (rpm)	18 V Approx. 1580 min -1 (rpm)
		14.4 V Approx. 1350 min -1 (rpm)

• Default setting: OFF
• The speed is the same using either 14.4 V or 18 V when H, M, L settings are selected.
• If a high mode is chosen, the speed is set as the table above.

3 Mode LED Light

Press the light button to select illumination setting.

Illuminated - Constant

Select by pressing lamp button light will activate when trigger is pressed. It will then stay illuminated for approximately 5 minutes even if tool is not used but will then switch off automatically to save power.

Illuminated - On trigger

By pressing the lamp button again, the mode will change to illumination only while the trigger is pressed. The light will switch off when the trigger is released.

Off

The light illuminates with very low current, and it does not adversely affect the performance or battery capacity.

CAUTION:

• The built-in LED light is designed to temporarily illuminate the small work area.
• Do not use it as a substitute for a regular flashlight, as it does not have sufficient brightness.

CAUTION: DO NOT STARE INTO BEAM.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

Battery Level Indicator

Press the battery level button. The battery level indicator shows the battery level in three levels while the button is pressed.

NOTE:

The indicator will not show the battery level when the button is pressed in the following cases:

• The tool is powered off. • Just after attaching the battery pack. • The main unit or battery level button has not been operated for approximately five minutes. Press the battery level button again after depressing the trigger switch. • If the battery temperature is high, stop the operation and wait until the battery temperature is low.

Indicator Battery status
	3 lamps illuminated	Fully charged or high charge level
	2 lamps illuminated	Approx. 60% remaining
	One lamp illuminated	Low level- Will require charging soon
	3 lamps flashing	Empty- Immediate charging required

This battery level function is only a guide, and the indication may change due to the condition of the battery or ambient temperature.

Excessive (complete) discharging of lithium ion batteries shortens their service life dramatically. The driver includes a battery protection feature designed to prevent excessive discharging of the battery pack.

Bit-locking Function

1. With the trigger switch not depressed and a screwdriver bit locked in place, the tool can be used as a manual screwdriver (up to 22.6 N·m, 230 kgf·cm, 199 in·lbs). There will be a little play in the chuck, but this is not a malfunction.
2. This feature is handy for tightening screws that require more torque than the maximum torque of the driver (position ☐ on the clutch), for confirming the tightness of a screw or to loosen an extremely tight screw.

Changing the Belt Hook Location Side [Fig.8]

The belt hook can be attached to either side of the unit.

1. Removing the hook

(1) Remove the nut. (2) Draw out the hook.

1. Attaching the hook to the other side

(1) Insert the hook in the other side. (2) Tighten the nut fully so that it securely fastened.

WARNING!

• Be sure to attach the belt hook securely to the main unit with the screw firmly fastened. When the belt hook is not firmly attached to the main unit, the hook may disconnect and the tool may fall. This may result in an accident or injury. • Periodically check screw for tightness. If found to be loose, tighten firmly.
• Be sure to attach the belt hook firmly and securely onto a waist belt or other belt. Pay attention that the tool does not slip off the belt. This may result in an accident or injury.
• When the tool is held by the belt hook, avoid jumping or running with it. Doing so may cause the hook to slip and the tool may fall. This may result in an accident or injury.
• When the tool is hooked onto the waist belt by the belt hook, do not attach driver bits to the tool. A sharp edge object, such as a drill bit, may cause injury or an accident.

Warning Functions

(1) Overheat Warning

Off (normal operation)

Illuminated: Overheat (motor)

Flashing: Overheat (battery)

Indicates operation has been halted due to motor or battery overheating.

To protect the motor or battery, be sure to note the following when carrying out this operation.

- If the motor or battery becomes hot, the protection function will be activated and the motor or battery will stop operating. The overheat warning lamp on the control panel illuminates or flashes when this feature is active.

• If the overheating protection feature activates, allow the tool to cool thoroughly (at least 30 minutes). The tool is ready for use when the overheat warning lamp goes out.
• Avoid using the tool in a way that causes the overheating protection feature to activate repeatedly.
• If the tool is operated continuously under high-load conditions or if it is used in hot-temperature conditions (such as during summer), the overheating protection feature may activate frequently.
• If the tool is used in cold-temperature conditions (such as during winter) or if it is frequently stopped during use, the overheating protection feature may not activate. The performance of the EY9L42 deteriorates significantly at and below 10°C due to work conditions and other factors.

(2) Voltage Reduction Warning

One lamp flashing

If the tool is subject to a sudden load during use that causes the motor to lock up, the overdischarge prevention sensor may be triggered, and the battery low warning lamp may flash. The lamp will stop flashing once you address the cause of the motor's locking up and cycle the trigger.

(3) Overload Warning

If the tool is subject to a sudden load during use that causes the motor to lock up, the overcurrent prevention sensor may be triggered, the voltage reduction warning lamp may illuminate and flash. (Bottom of it illuminates and middle and top flashes.)

The lamp will stop illuminating and flashing once you address the cause of the motor's locking up and cycle the trigger.

[Battery Pack]

For Appropriate Use of Battery Pack [Fig.9]

• The rechargeable batteries have a limited life.
• For optimum battery life, store the Li-ion battery pack following use without charging it.
• When operating the battery pack, make sure the work place is well ventilated.

For safe use

• The battery pack is designed to be installed by proceeding two steps for safety. Make sure the battery pack is installed properly to the main unit before use.
• If the battery pack is not connected firmly when the switch is switched on, the overheat warning lamp and the battery low warning lamp will flash to indicate that safe operation is not possible, and the main unit will not rotate normally. Connect the battery pack into the unit of the tool until the red or yellow label disappears.

[Battery Charger]

Charging

CAUTION:

1) If the temperature of the battery pack falls approximately below -10°C (14°F), charging will automatically stop to prevent degradation of the battery. 2) The ambient temperature range is between 0°C (32°F) and 40°C (104°F).

If the battery pack is used when the battery temperature is below 0°C (32°F), the tool may fail to function properly. 3) Use the charger at temperatures between 0°C and 40°C, and charge the battery at a temperature similar to that of the battery itself. (There should be no more than a 15°C difference between the temperatures of the battery and the charging location.)

4) When charging a cool battery pack (below 0°C (32°F)) in a warm place, leave the battery pack at the place and wait for more than one hour to warm up the battery to the level of the ambient temperature. 5) Cool down the charger when charging more than two battery packs consecutively. 6) Do not insert your fingers into contact hole, when holding charger or any other occasions. 7) Unplug the charger when not in use.

NOTE:

Your battery pack is not fully charged at the time of purchase. Be sure to charge the battery before use.

How to charge

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is inserted into the AC power supply, but this is not a problem in terms of safety.

1. Connect the battery pack firmly into the charger.

1 Line up the alignment marks and place the battery onto the dock on the charger.

NOTE:

Not all battery packs display the alignment mark (Q) (on page 2).

2 Slide forward in the direction of the arrow. [Fig.10]

1. During charging, the charging lamp will be lit. When charging is completed, an internal electronic switch will automatically be triggered to prevent overcharging.

- Charging will not start if the battery pack is hot (for example, immediately after heavy-duty operation). The orange standby lamp will be flashing until the battery cools down. Charging will then begin automatically.

1. The charge lamp (green) will flash slowly once the battery is approximately 80% charged.

1. When charging is completed, the charging lamp in green color will turn off.
2. If the temperature of the battery pack is 0°C or less, charging takes longer to fully charge the battery pack than the standard charging time.

Even when the battery is fully charged, it will have approximately 50% of the power of a fully charged battery at normal operating temperature.

1. Consult an authorized dealer if the charging lamp (green) does not turn off.
2. If a fully charged battery pack is inserted into the charger again, the charging lamp lights up. After several minutes, the charging lamp in green color will turn off.
3. Remove the battery pack while the battery pack release button is held up.

[Fig.10]

LAMP INDICATIONS

Battery Recycling

ATTENTION:

For environmental protection and recycling of materials, be sure that it is disposed of at an officially assigned location, if there is one in your country.

Information for Users on Collection and Disposal of Old Equipment and used Batteries

EN

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2012/19/EC and 2006/66/EC.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

V. MAINTENANCE

- Use only a dry, soft cloth for wiping the unit.

Do not use a damp cloth, thinner, benzine, or other volatile solvents for cleaning.

In the event that the inside of the tool or battery pack is exposed to water, drain and allow to dry as soon as possible. Carefully remove any dust or iron filings that collect inside the tool. If you experience any problems operating the tool, consult with a repair shop.

VI. ACCESSORIES

Use only bits suitable for size of drill's chuck.

VII. APPENDIX

MAXIMUM RECOMMENDED CAPACITIES

Model No. EY74A2 EY79A2
Motor voltage 14.4 V DC 18 V DC 14.4 V DC 18 V DC
Screw driving Ma	chine screw M5
	Wood screw Φ 6.8 mm Φ 8 mm Φ 6.8 mm Φ 8 mm
Drilling Self-drilling	screw Φ 6 mm
	For Wood	Φ 35 mm	Φ 38 mm	Φ 35 mm	Φ 38 mm
	For Metal	Φ 13 mm
	For Masonry	—		Φ 13 mm

EN

WARRANTY SUPPLEMENT

• The breakdown and damage caused by usage consistent for a long time (e.g.: factory work on the assembly line, etc.) is out of warranty.
• In the event that the inside of the tool or battery pack is exposed to water, drain and allow to dry as soon as possible. Carefully remove any dust or iron filings that collect inside the tool. If you experience any problems operating the tool, consult with a repair shop.

VIII. SPECIFICATIONS

NOTE: Weight indication

Greater than or equal to 1 kg: indicated by 0.05 kg.

Less than 1 kg: indicated by 0.01 kg.

MAIN UNIT

Model No. EY74A2 EY7		9A2
Motor voltage 14.4 V DC		18 V DC 14.4	V DC 18 V DC
No load speed	Low 30 – 400 min -1 (rpm)		30 – 470 min -1 (rpm)	30 – 400 min -1 (rpm)	30 – 470 min -1 (rpm)
	High	70 – 1350 min 1 (rpm)	70 – 1580 min 1 (rpm)	70 – 1350 min 1 (rpm)	70 – 1580 min 1 (rpm)
Chuck capacity 1.5 mm		m – 13 mm 1.5 mm – 13 mm
Clutch torque Approx. 0.5 N•m – 4.4 N•m Approx. 1.0 N•m – 4.4 N•m
Overall length 178 mm		188 mm
Weight	With battery pack: EY9L45	1.90 kg	—	1.95 kg	—
	With battery pack: EY9L47	1.70 kg	—	1.70 kg	—
	With battery pack: EY9L51	—	2.05 kg	—	2.05 kg
	With battery pack: EY9L52	—	1.80 kg	—	1.85 kg
	With battery pack: EY9L53	—	1.80 kg	—	1.85 kg
	With battery pack: EY9L54	—	2.05 kg	—	2.10 kg
Noise, Vibration		See the included sheet

ONLY FOR U. K.

IX. ELECTRICAL PLUG INFORMATION

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.

A 5 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 5 amp and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced.

If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY. THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below.

If in any doubt please consult a qualified electrician.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

Blue: Neutral

Brown: Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED. Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with the letter E or the Earth Symbol 1/2 .

How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse and fuse cover if it is removable.

This apparatus was produced to BS800.

Changing the position of the belt hook [Fig.8]

Overheating (motor)

Blinker:

Overheating (battery)

Lights: Overheating (motor)

Blinker: Overheating (battery)

VIII. TECHNICAL DATA

Panasonic Testing Centre

Panasonic Europe Ltd. Hamburg office

Winsbergring 15,

22525 Hamburg,

Germany

Panasonic Corporation

1006, Kadoma, Osaka 571-8501, Japan

http://www.panasonic.com

EN. DE. FR. IT. NL. ES. DA. SV. NO. FI. TR. PL. CS. HU.

EY971074A202 2015.10 F Printed in China