RTT88 - Turntable Ricatech - Free user manual and instructions

USER MANUAL RTT88 Ricatech

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER. PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Black triangular warning symbol with a white lightning bolt and downward arrow (no text)

The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.

CAUTION

RRISSKK OOFF EELLEECCT DDOO NNOOTT OOPPE

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER - SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

C S S H O

The exclamation point within an equilateral triangle is intended to alert user to the presence of important operating and maintenance (servicing) instruction in the literature accompanying the appliance.

"Ventilation not being impeded."

"Do not exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus."

Specification

FREQUENCY

: FM 88 -108 MHz

AM 530 - 1600 KHz

USB Port 2.0

: Full Speed 512MB - 4GB (Support FAT16, FAT32)

POWER SOURCE

: AC230V/50Hz

ANTENNA

: External antenna for FM

Built-in ferrite bar for AM

POWER CONSUMPTION

: 15W

SPEAKER SIZE

: 2" x 3" Dynamic type x 2

SPEAKER OHM

: 4 ohm

SPEAKER WATT

: 3-5W

POWER OUTPUT

: 1.2W x 2

* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

IMPORTANT SAFEGUARDS FOR AUDIO PRODUCTS

PLEASE READ CAREFULLY THE FOLLOWING IMPORTANT SAFEGUARDS THAT ARE APPLICABLE TO YOUR EQUIPMENT.

1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5. Water and Moisture - The appliance should not be used near water-for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swim ming pool and the like.

6. Carts and Stands - The appliance should be used only with a cart or stand that is recommended by the manufacturer.

6A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

1. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.

2. Ventilation - The appliance should be situated so that its location or position does not interfere with-its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

3. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

4. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance.

5. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means of an appliance is not impeded.

6. Power - Cord Protection - Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, and the point where they exit from the appliance.

7. Cleaning - The appliance should be cleaned only as recommended by the manufacturer.

8. Antenna - This product is designed for use with the antenna attached and should not be connected to any other external antennas.

9. Non-use Periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time.

16.Object and Liquid Entry - Care should be taken so objects do not fall and liquids are not spilled into the enclosure through openings

1. Damage Requiring Service - The appliance should be serviced by qualified service personnel when:

A. The power-supply cord of the plug has been damaged; or

B. Objects have fallen, or liquid has been spilled into the appliance; or

C. The appliance has been exposed to rain, or

D. The appliance does not appear to operate normally or exhibits a marked change inperformance, or

E. The appliance has been dropped, or the enclosure damaged.

1. Servicing - The user should not attempt to service the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

LOCATION OF PARTS

BACKWARD SKIP X-BASS ON/OFF FORWARD SKIP REC/ERASE POWER INDICATOR LCD DISPLAY PROGRAM STOP/ SD/USB PLAY/ PAUSE REPEAT RICHATECH® VOLUME ON/OFF MAX OFF X-BASS UK REC/ERASE SD/USB RADIO PHONO SENSOR AM 530 600 700 900 1200 1400 1600 KHz FM.88 92 96 100 104 106 108 MHz AM FM.5ST USB PORT DIAL SCALE AM/FM FM.ST SWITCH TUNING KNOB SPEAKER VOLUME ON/OFF KNOB RADIO\ SD/USB\ PHONO SWITCH EARPHONE JACK SD CARD SUSKER USB TUNING KNOB SPEAKER

EXTERNAL FM ANTENNA LINE OUT L R LINE IN ON OFF LINE IN JACK LINE OUT JACK LINE IN SWITCH AC POWER PLUG

LOCATION OF PARTS

STOP/SD/USB PLAY/PAUSE BACKWARD SKIP 0-9 REC/ERASE 12 45 7 REC/ERASE SD/USB PROG FORWARD SKIP PROGRAM 6 8 3 9 0 REPEAT REPEAT

SPEED CONTROL SWITCH TONE ARM REST TONE ARM ADAPTER FOR 45 RPM RECORDS SPINDLE TURNTABLE

Unpacking

Pure mechanical assembly diagram without any text, numbers, or symbols

1 packing materials from unit. Note: Save all packing materials.
2 Remove plastic bag covering radio.
3 Remove tie from A/C cord and untie antenna wire on back of radio.
4 Open lid and remove styrofoam shipping material from turntable.
5 Remove black tie-wrap from under the tone arm.
6 Remove white protective needle cover by gently pulling towards the front of the unit.

Remarks:

a) ESD remark: In case of malfunction due to electrostatic discharge, just reset the product (reconnect of power source may be required) to resume normal operation.
b) Electrical Fast Transient (Burst) Remark (I2): In case of malfunction due to electrical fast transient (Burst), just reset the product. (reconnect of power source may be required) to resume normal operation.

SETUP

1. Unwind the AC POWER CORD at the back of unit.
2. Untie the FM antenna and allow it to hang down in a straight line for optimum FM reception. If you have trouble tuning a FM station, move the external FM antenna for best reception. Do not connect FM antenna to outside antenna.

Power Source

1. Plug the A/C cord into appropriate outlet.

Radio Operation

1. Set the Function switch to RADIO.
2. Switch the unit ON by turning the VOLUME knob to the on Position.
3. Turn the VOLUME control in mid-range position.
4. Slide the Band switch to the desired band (AM or FM or FM.ST).
5. Select the desired radio station by rotating Tuning Knob
6. Adjust the Volume Knob to the desired sound level.

Antenna

Antenna: for FM reception, the unit is provided with a FM WIRE ANTENNA, move the wire until the reception is clear and with no interferences. For AM reception, the unit is provided with a directional build-in ferrite antenna. Rotate the set to find the position in which the best reception is obtained. Do not connect the EXTERNAL FM ANTENNA to any outside antenna.

1. Slide THE FUNCTION Switch to SD/USB mode.

2. Switch the unit ON by turning the VOLUME knob to the on Position. If no Card has been detected, "Read"*'3f"No Card" will be show on the display.

1. Turn the VOLUME control in mid-range position.
2. Insert SD-Card into the card slot. "READ" is displayed as the system scans the contents of SD card.
3. Track no. 1 of root folder (Folder 1) will be displayed after reading SD card contents.
   Press PLAY/PAUSE / 📋 to start music.
4. Press the FORWARD SKIP / 🎨 / BACKWARD SKIP / 🎨 once or repeatedly until the desired track number appears on the display. Release the button – the track will start playing automatically.
5. Press STOP / ☐ stop playback.
6. To pause the music, press PLAY/PAUSE / ▶, press it again to resume play.

USB operation:

1. Slide the FUNCTION Switch to SD/USB mode.
2. Switch the unit ON by turning the VOLUME knob to the on Position.
3. Turn the VOLUME control in mid-range position.
4. In stop mode Press STOP / (NDUSB) and hold key over 2 seconds will switch SD->USB. If no USB has been detected, "NO USB" will show on the Display.

1. Plug-in USB mass storage device. READ is displayed as the system scans the contents of USB device.

1. Track no. 1 of root folder (Folder 1) will be displayed after reading USB device contents. Press PLAY/PAUSE / 📋 to start music.

1. Press the FORWARD SKIP / 🎨 / BACKWARD SKIP / 🎨 once or repeatedly until the desired track number appears on the display. Release the button – the track will start playing automatically.
2. Press STOP / ☑ to stop playback.
3. To pause the music, press PLAY/PAUSE / ⬤, press it again to resume play.

Remarks:

1. USB connector does not support connection with USB extension cable is not designed for communication with computer directly.
2. It is not guarantee that all USB memory devices and SD cards will work on this audio system

IMPORTANT:

Do not disconnect the USB device SD card during USB/SD card mode, as this may damage the external device or its files. Please power off first or press another Mode before safely disconnecting the USB device /SD card.

USB Specification:

Interface

• USB 2.0 Full speed, HOST (USB HUB is not supported) Corresponding Flash memory
• Compatible with MPEG Audio 1, 2, 2.5
• Compatible with Layer 1, 2, 3
• Compatible with Bit rate: 128 – 320 Kbps
• Subfolder nest : 8 levels
• Number of track / titles max 999
• Support ID3 tag V2.0

TURNTABLE

PREPARING TO USE THE TURNTABLE

1. Lift up lid and remove black tie-wrap by untwisting and gently sliding out from TONE ARM
2. Remove cardboard shipper.
3. Remove white protective needle cover by gently pulling towards front of unit.
4. Release TONE ARM and hold-down clip by gently pushing to the right.
   This will unlock tone arm from its ARM REST. Re-lock the hold-down clip when moving the unit to another location.

TURNTABLE OPERATION

1. Slide the FUNCTION Switch to PHONO mode.
2. Switch the unit ON by turning the POWER switch to the on Position.
3. Turn the VOLUME control in mid-range position.
4. Set the SPEED CONTROL SWITCH to the correct speed (33 1/3, 45 or 78 rpm) for the selected record.
5. Move the tone arm over the record and lower it to the point you want the record to start.
6. At the end of the record, the TONE ARM will stop automatically. You must return it to the TONE ARM REST by hand.

ACCESSORY SUPPLIED :

Adaptor for 45 rpm records

To play a 45 rpm record, remove the adaptor by placing thumb & forefinger in recesses and pulling it upwards.

Then placing it on the SPINDLE. The record can then be placed on the turntable.

Abstract circular diagram with three curved segments and a central dot (no text or symbols)

PROGRAMMING TRACKS

You may store up to 20 tracks in the desired sequence.

1. In the stop position, press PROGRAM / Ⓞ to start programming. Icon “P” and P0-01 start flashing. ☐☐1 P - 01

2. Press the FORWARD SKIP/ 🎨 / BACKWARD SKIP/ 🎨 once or repeatedly until the desired track number appears in the display.

3. Press PROGRAM / PROG to confirm, display shown stored track no. and next store position.

1. Repeat step 2-3 to select and store all desired tracks. FULL is displayed if you attempt to program more than 20 tracks

。 FULL

1. Press PLAY/PAUSE/ to play the program.

Erasing the programme

You can erase the contents of the memory by :

• once if in stop position, twice during playback
• Press POWER
• Select another sound source

Play mode

1. Press REPEAT / ON remote at Play mode.
2. Default Play Mode function is OFF.
3. REPEAT 1 / REPEAT FOLDER / REPEAT ALL . THREE kinds of Play Mode can be chosen in MP3 type.

X-BASS

Press the X-BASS ON/OFF to ON or OFF the X-BASS effect(Adjust the volume level to mid to maximize the X-BASS effect).

Line Out Outputs

1. You can connect this unit to different sources using the auxiliary output jacks.
2. Connect the auxiliary cables (not supplied) to the LINE OUT JACK and to the auxiliary inputs of the desired component. See the owner's manual for the operating instructions for the desired component. The LINE OUT JACK only output a signal and will not run external speakers without using a separate amplified source.

Auxiliary Input

1 You can connect external components to your unit by using the Auxiliary Input.
2 Plug Auxiliary cable into the LINE IN JACK on the back of your unit.
3 Switch the LINE IN SWITCH to the ON position.
4 Plug the other end of the Auxiliary cable into the output jack on your desired external component.
5 Check the volume level of your external component.
6 See operators manual for correct operation of the external component.

NOTE: When not using the Auxiliary Input, make sure the LINE IN SWITCH is in the OFF position.

MP3 copying

1. In USB or SD card playback, Press REC/ERASE/ RECREASE to start Mp3 copying from USB to SD card or SD card to USB.Playback will be stopped and system will scan the contents of USB/SD card and create folder to store MP3 track.

2. icon "REC" displayed

3. Message COPY will be displayed.

4. The target device icon "USB" or "CARD" start flashing, MP3 copying start, the process will stop as copy finished.
5. Current MP3 will be playback from beginning
6. You can copy Mp3 from USB to SD card or SD card to USB at Stop Mode press REC/ERASE / RECREASE It may not to copy all MP3 depending on the MP3 file, USB device and SD card

From Phono to SD / USB

The system is capable of converting audio signal from PHONO input to MP3 format and store in USB mass storage device or SD card (default USB if both devices are detected)

1. Slide the FUNCTION button to PHONO mode.

1. Press REC/ERASE / RECREASE to start ripping, the system will scan the contents of USB/SD card and create folder to store MP3 tracks.
2. Icon "REC" and message "TO" are displayed of about 15 seconds, icon "USB" start flashing.
3. The target device icon "USB" or "CARD" start flashing as REC begins.

1. Press STOP / ☐ exit PHONO Rec

Delete MP3 tracks

The system support deleting previous recorded MP3 or existing files.

1. In USB or SD card playback mode, press and hold REC/ERASE / (RECERASE) for 2 seconds, current playback track is stopped and will be deleted.
2. Message "delete" is displayed

Auxiliary Output

1 You can connect your radio to different sources using the auxiliary output.
2 Plug Auxiliary cables (not supplied) into the LINE OUT JACK.
3 Connect the other end of the Auxiliary cables into the input on your desired component.
4 See the owners' manual for the component for correction operation.

NOTE: The Auxiliary Output is a passive signal level output only and will not power speakers.

Auxiliary Input

1 You can connect external components to your unit by using the Auxiliary Input.
2 Plug Auxiliary cable into the LINE IN JACK on the back of your unit.
3 Set the FUNCTION SWITCH to LINE IN mode
4 Plug the other end of the Auxiliary cable into the output jack on your desired external component
5 Check the volume level of your external component.
6 See operator's manual for correct operation of the external component.

Headphone Jack Operation

1 Connect headphones to the Headphone Jack
2 Adjust volume to the desired listening level.

NOTE: When using headphones, the sound to the unit speakers will be cut off.

NOTE: Headphones not included with unit.

Headphone jack

The sound from all speakers is cut off

Troubleshooting

There is no Power

1 The AC Power plug is not well connected.
2 Check to see that the ON/OFF volume knob is in the on position.

There is no Sound

1 Check the volume level by turning the volume knob.
2 Make sure the LINE IN SWITCH is in the OFF position if the LINE IN JACK is not being used.

Turntable will not work

1 Make sure the function switch is set to phono.
2 Try moving the tone arm to the right until you hear a click.
3 Make sure the protective needle cover is removed.

Recycling

Simple line drawing of a trash bin with two crossed lines (no text or symbols)

This crossed bin symbol on the appliance indicates that the product, at the end of its life must be disposed of seperatly from domestic waste, either by taking it to a separate waste disposal site for electric and electronic appliance or by returning it to your dealer when you buy another similar. The user responsible for taking the appliance to a special waste disposal site at the end of its life. If the disused appliance is collected correctly as separate waste, it can be recycled, treated and disposed of ecologically, this avoids a negative impact on both the environment and health, and contributed toward the recycling of the product's materials. For further information regarding the waste disposal service available, contact your local waste disposal agency or the place of purchase.

CUSTOMER SUPPORT

You can contact the Ricatech customer service when you have a question or a problem with your Ricatech product. You can contact us by telephone and email.

Email

For customer support by email, please sent a email to [e-mail] Please make sure that you mention the model number and serial number of the product, mention your name & address and describe your question or problem clearly.

Telephone

For customer support by telephone, please dial [phone]. One of our service staff will be ready to serve you. For full procedure please visit the website of Ricatech at: www.ricatech.com

Hereby, Ricatech B.V. declares that this turntable is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Ricatech B.V.

Cornusbaan 1 2908 KB Capelle a/d IJssel The Netherlands

Nederlands

WAARSCHUWING :

STEL HET APPARAAT NIET BLOOT AAN REGEN OF VOCHT OM GEVAAR VOOR BRAND OF EEN ELEKTRISCHE SCHOK TE VOORKOMEN. DE BEHUIZING NIET VERWIJDEREN. CONTROLELAMPJES ZIJN OP HET APPARAAT GESOLDEERD. GEEN DOOR DE GEBRUIKER TE ONDERHOUDEN ONDERDELEN AAN DE BINNENKANT. LAAT ONDERHOUD OVER AAN GEKWALIFICEERD ONDERHOUDS PERSONEEL.

Black triangular warning symbol with a white lightning bolt and downward arrow (no text)

C S S H O

Pure mechanical assembly diagram without any text, numbers, or symbols

Abstract circular diagram with three curved segments and a central dot (no text or symbols)

TRACKS PROGRAMMEREN

U kunt maximaal 20 tracks opslaan in de gewenste volgorde.

Hereby, Ricatech B.V. declares that this turntable is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Ricatech B.V.

Cornusbaan 1

2908 KB Capelle a/d IJssel

The Netherlands

AVERTISSEMENT:

POUR RÉDUIRE LES RISQUES DE CHOC ÉLECTRIQUE, N'EXPOSEZ PAS CET APPAREIL À LA PLUIE NI À L'HUMIDITÉ. N'ENLEVEZ PAS LE COUVERCLE. LES VOYANTS SONT SOUDÉS SUR PLACE. L'INTÉRIEUR NE CONTIENT AUCUN COMPOSANT À RÉPARER PAR L'UTILISATEUR. CONFIEZ VOTRE APPAREIL SEULEMENT AU PERSO DE SERVICE QUALIFIÉ.

Black triangular warning symbol with a white lightning bolt and downward arrow (no text)

C S S H O

(Support FAT16, FAT32)

Pure mechanical assembly diagram without any text, numbers, or symbols

Abstract circular diagram with three petal-like shapes and a central dot (no text or symbols)

Hereby, Ricatech B.V. declares that this turntable is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Ricatech B.V.

Cornusbaan 1 2908 KB Capelle a/d IJssel The Netherlands

WARNUNG:

Black triangular warning symbol with a white lightning bolt and downward arrow (no text)

Black triangular warning symbol with exclamation mark (no text or numbers)

Pure mechanical assembly diagram without any text, numbers, or symbols

Abstract circular diagram with three petal-like shapes and a central dot (no text or symbols)

TITELPROGRAMMIERUNG

Hereby, Ricatech B.V. declares that this turntable is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Ricatech B.V.

Cornusbaan 1

2908 KB Capelle a/d IJssel

The Netherlands

ATENCIÓN :

PARA RÉDUCIR LOS RIESGOS DE CHOQUE ELÉCTRICO, NO EXPONGA ESTE APARATO À LA LLUVIA NI A LA HUMEDAD. NO QUITE LA TAPA. LOS PILOTOS SON SOLDADOS EN LUGAR. EL INTERIOR NO CUENTA CON COMPONENTES A REPARAR POR EL USUARIO. CONFÍE SU APARATO SOLAMENTE AL PERSONAL DE SERVICIO CALIFICADO.

Black triangular warning symbol with a white lightning bolt and downward arrow (no text)

C S S H O

Pure mechanical assembly diagram without any text, numbers, or symbols

Simple circular diagram with three petal-like shapes inside, no text or symbols present.

Antena

Hereby, Ricatech B.V. declares that this turntable is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Ricatech B.V.

Cornusbaan 1

2908 KB Capelle a/d IJssel

The Netherlands