LP 2 Go - Turntable ION - Free user manual and instructions

USER MANUAL LP 2 Go ION

Make sure that the items listed below are included in the box:

• Quick Start Guide
  • Safety Instructions and Warranty Information Booklet
  • EZ Vinyl/Tape Converter Software CD
  • Pre-Mounted Needle
  • Pre-Mounted Slipmat
  • 45 RPM Adapter
• USB Cable
  • USB-to-AC Power Supply

READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT

Go to http://www.ionaudio.com for product registration.

INTRODUCTION

You should install EZ Vinyl/Tape Converter to take advantage of computer recording. EZ Vinyl/Tape Converter is the quickest and easiest way to turn your recordings into digital media. EZ Vinyl/Tape Converter conveniently saves your recordings in your iTunes* library. We have included a handy software Quickstart Guide with step-by-step instructions on software installation and operation.

Visit www.ionaudio.com/ezvc to download the latest version of EZ Vinyl/Tape Converter software or for helpful troubleshooting guide and additional support.

To install the software: simply insert the included CD into your computer and follow the on-screen instructions. After you finish converting your vinyl, you can then burn to CD or load onto portable media devices.

Visit www.ionaudio.com/computer-optimization for more information on optimizing your computer for audio.

* iTunes is a trademark of Apple, Inc., registered in the U.S.A. and other countries.

FEATURES

1. PLATTER – Place your record here.
2. TONEARM - LP2GO comes with a ready to use pre-balanced tonearm and cartridge.
3. ARM CLIP - This specially designed arm clip secures the tonearm while at rest or when not in use. The arm clip has been designed to remain in the up position while unlocked. When a record is on the platter, place the arm clip down to avoid scratching your vinyl.
4. 45 RPM ADAPTER HOLDER - Holds the included 45 RPM adapter. When not using the adapter, please place it in this holder.

1 2 3 4 5 6 7 8 9 10 33/45 USB BATT UV DC turn this knob clockwise

1. VOLUME/POWER KNOB – To power on LP2GO, turn this knob clockwise until it clicks. When powered on, use this knob to adjust the volume. To turn off LP2GO, turn this knob counterclockwise until it clicks.

2. 33 / 45 SWITCH – This switch controls the RPM of the turntable platter.

3. SPEAKER – The record's audio will be played through this built-in speaker.

4. USB/BATTERY SWITCH – When the switch is in the "down" position, the turntable will be powered through a USB connection

IMPORTANT: Make sure that the slipmat is always placed on top of the platter while using the turntable. Failure to use the slipmat may cause damage to your media as well as damage to the turntable.

Remove the plastic cartridge cover (needle cover) before operating the turntable.

- the USB AUDIO OUTPUT connected to either (A) your computer or (B) wall power, using the included USB-to-AC power supply. When the switch is in the "up" position, the turntable will be powered by batteries (if batteries are installed).

1. HEADPHONE OUTPUT – Connect 1/8" stereo headphones here (not included). The speaker output stops playing audio once headphones are connected.

2. USB PORT – Use the included USB cable to connect your turntable to your computer. The USB connection will provide power to the turntable as well as the audio from the turntable to your computer. You can also power the turntable by using the included USB cable and USB-to-AC power supply to connect your turntable to wall power.

Note: LP2GO may appear as "USB Microphone" or "USB Composite Device" in your computer's sound control panel (even though the included EZ Vinyl/Tape Converter manual says it appears as "USB Audio Codec").

1. BATTERY COMPARTMENT – Remove the cover and place 4 AA batteries into this compartment. Be sure the positive and negative poles of the batteries are facing the proper direction.

1. Undo and lower arm clip.
2. Raise the tonearm, then move it to the side.
3. Place the record on the platter.
4. Select speed (33/45 RPM); use the included 45 RPM adapter if needed.
5. Lower the tonearm onto record; the record will begin playing.
6. Adjust volume with ON/OFF knob.
7. When finished, raise the tonearm and return it to rest on the arm clip.

Diagram of a mechanical device with a speech bubble containing radiating lines, no text or symbols present

Diagram of a mechanical or optical setup with directional arrows and components, no visible text or symbols

3

4 33/45

5 板·磨

6 VOLUME

Line drawing of a mechanical device with no visible text or symbols

TROUBLESHOOTING

Refer to the following troubleshooting scenarios if you experience difficulty recording your vinyl to your computer.

PROBLEM CAUSE SOLUTION
I am not hearing any audio when I am recording.	Needle is not on the record.	Place the needle on the record.
	Turntable not powered.	Make sure that the turntable is connected to a computer that is powered on.
I am experiencing poor sound quality.	Cartridge connection is not secure.	Cartridge must be securely connected to the tonearm whenever you are using the turntable.
	Vinyl record is dirty or scratched.	Try dusting off and gently wiping the surface of the record before playing it.
When recording into my computer on Windows Vista, my recordings are mono instead of stereo.	Recording input properties in Vista not set to “stereo”.	In Vista, you may need to manually specify “stereo” for the recording input.Go to Start ▶ Control Panel ▶ Sound (in Classic View). Then, click on the Recording tab and highlight the Microphone input (USB Audio Codec). Click on Properties to bring up the input settings. Next, click on the Advanced tab and select “2 channel, 16 bit, 44100 Hz (CD quality)” in the Default Format pull-down menu. Lastly, click Apply to accept the settings.
My music is playing at a strange pitch.	Incorrect speed selected on the turntable.	Make sure that you are playing your records at the speed they were intended to be played. Select between the different speeds (33 or 45 RPM).

BEFORE RETURNING THE PRODUCT, please contact ION Audio or your retailer for technical support. Contact information can be found in the Safety Instruction Booklet included with this product.

Technical line drawing of a mechanical assembly with a magnified inset showing radial blades (no text or symbols)

Diagram of a mechanical or industrial process with directional arrows indicating movement (no text or symbols)

Diagram of a mechanical setup with a rotating disk and a robotic arm (no text or symbols)

4 33/45

5 板·肋

6 VOLUME

Line drawing of a mechanical device with no visible text or symbols

Diagram of a train with a thought bubble showing radiating lines, no text or symbols present

Diagram of a mechanical or optical setup with arrows indicating motion or force direction (no text or symbols)

3

4 33/45

Line drawing of a mechanical device with a lever and base, no text or symbols present

6 VOLUME

Line drawing of a mechanical device with no visible text or symbols

DÉPANNAGE

Simple line drawing of a mechanical device with a speech bubble containing abstract lines, no text or symbols present.

Diagram of a mechanical device with directional arrows indicating motion or force (no text or symbols)

3

4 33/45

5 控制

6 VOLUME

Line drawing of a mechanical device with no visible text or symbols

Diagram of a mechanical device with a thought bubble showing radiating blades (no text or symbols present)

Diagram of a mechanical or optical setup with directional arrows and components (no text or symbols)

3

4 33/45

5 双 一 钢

VOLUME X X

Line drawing of a mechanical device with no visible text or symbols

FEHLERHILFE

Technical line drawing of a mechanical device with a thought bubble showing radiating blades (no text or symbols)

Diagram of a mechanical or industrial process with directional arrows indicating movement (no text or symbols)

3

4 33/45

Line drawing of a mechanical device with no visible text or symbols

6 VOLUME

Line drawing of a mechanical device with a cylindrical component and a circular base (no text or symbols)

PROBLEEM OPLOSSING