Question 1

How to pair the transmitter and receiver of the AKG WMS 470 wireless microphone system?

Accepted Answer

The AKG WMS 470 system uses infrared synchronization to pair the transmitter and receiver. Before you begin, make sure you have at least two AA batteries (alkaline or rechargeable) and that both devices are close to each other.

Step 1: Turn on the receiver. Connect the SR 470 receiver to a 12V power source (power adapter provided) or insert the AA batteries into its battery compartment. The receiver will turn on and display the current frequency on its LCD screen.

Step 2: Select a frequency on the receiver. Use the menu buttons to navigate to the "GROUP/CHANNEL" menu and select an available frequency group (100 preset channels cover the UHF band 500-865 MHz). You can also use the "AUTO" menu to start an automatic search for interference-free channels. Confirm your choice: the frequency will be displayed on the receiver's LCD screen.

Step 3: Prepare the transmitter in programming mode. Install an AA battery in the transmitter (HT 470 or PT 470 transmitter). Set the three-position switch "ON-MUTE/PRG-OFF" (19) to the middle position "MUTE/PRG". The LCD screen of the transmitter will alternate between the current frequency and "PRG IR" to indicate that it is ready to receive settings from the receiver.

Step 4: Synchronize via infrared. Point the infrared sensor (17) located on the front of the transmitter directly at the infrared transmitter (8) of the receiver, at a maximum distance of 10 cm (4 inches). Hold this position for a few seconds. The infrared will then transmit the selected frequency, audio gain (HI or LO), and receiver settings to the transmitter. The infrared sensor of the WMS 470 has a very narrow radiation angle (about 10°) to ensure that only one transmitter will be tuned to the same frequency.

Step 5: Remove the transmitter from programming mode. Once the display of the transmitter stabilizes, switch the "ON-MUTE/PRG-OFF" switch to the "ON" position. The transmitter is now active and operates on the frequency synchronized with the receiver. The status LED (20) will light up green.

Step 6: Check the connection. Speak into the transmitter's microphone and observe the audio bar graph (d) on the receiver's LCD screen. If the signal level rises, the synchronization is successful. The "LOCK" symbol will also confirm that the receiver is correctly receiving the RF signal from the transmitter.

Tip: if you have multiple transmitters to synchronize, repeat steps 3 and 4 for each transmitter. Each transmitter will receive the receiver's settings via infrared, without needing to change the frequency on the receiver.

Question 2

How to use the AKG HT 40 PRO wireless microphone system?

Accepted Answer

To effectively use the AKG HT 40 PRO wireless microphone system, follow the steps below:

1. Installing the batteries

Open the battery compartment located at the back of the microphone.
Insert new AA batteries, ensuring the correct polarity is observed.

2. Powering on

Turn on the microphone by pressing the power button. A light indicator should turn on.

3. Setting the frequency

Ensure that the microphone and receiver are set to the same frequency. Use the frequency selection button on the microphone to choose the appropriate frequency.

4. Connecting to the receiver

Connect the receiver to your audio system (mixer, amplifier, etc.) using a suitable audio cable.
Turn on the receiver and check that the signal indicator is active.

5. Sound test

Speak into the microphone to check the sound transmission.
Adjust the volume on the receiver if necessary.

6. Regular use

Use the microphone normally while staying within range of the receiver to avoid dropouts.

7. Powering off

Turn off the microphone and receiver after use to save battery.

Question 3

Why does the light on the AKG HT 40 wireless microphone turn on and then quickly turn off?

Accepted Answer

When the light on the AKG HT 40 wireless microphone turns on and then quickly turns off, it may indicate several possible causes. Here’s how to diagnose and resolve this issue:

1. Checking the power supply

Make sure that the batteries are correctly inserted with the right polarity.
Replace the batteries if they are worn out or depleted, as low power can cause this behavior.

2. Checking the power switch

Ensure that the microphone switch is in the ON position.
A faulty or improperly engaged switch can lead to unstable power.

3. Checking connections and interference

Make sure the microphone is at a reasonable distance from the wireless receiver.
Keep the device away from other sources of electronic interference (mobile phones, Wi-Fi routers, etc.).

4. Resetting the device

Turn off and then turn on the microphone to attempt a reset.
If the problem persists, disconnect and reconnect the receiver, or reset the settings if possible.

If after these checks the light continues to turn on and off, it may indicate a hardware defect requiring repair or replacement.

User manual AKG : user manuals and guides in PDF

Models AKG most viewed

Browse manuals AKG by appliance type

Recent questions about devices AKG