Q: How to resolve the message "No signal input A" on the EPSON EMP-TW10 projector connected to a laptop via HDMI/VGA?

If your EPSON EMP-TW10 projector displays the message "No signal input A" while your laptop is connected via an HDMI or VGA cable, here are several steps to follow to resolve this issue: 1. Check the connections Make sure the HDMI or VGA cable is properly connected to both the laptop and the projector. If you are using an HDMI to VGA adapter, ensure it is properly connected and functional. 2. Select the correct input source on the projector Use the remote control or the buttons on the projector to select the source corresponding to the port used (HDMI or VGA). On the projector, press the Source or Input button and choose the correct input. 3. Configure the display on your laptop On Windows, press Windows + P to open the display options. Select Duplicate or Extend to enable projection on the projector. 4. Test the hardware Try another HDMI or VGA cable to rule out a faulty cable. Test the HDMI/VGA adapter with another device if possible. 5. Restart the devices Turn off and then turn on your laptop and the projector to reset the connection. 6. Check the display resolution Ensure that your laptop's resolution is compatible with the projector. If necessary, reduce the resolution in your laptop's display settings to test if this resolves the issue. By following these steps, you should be able to resolve the message "No signal input A" and display your laptop's image on the EPSON EMP-TW10 projector.

Question 1

How to turn on and print with my Epson WorkForce WF-2930 printer?

Accepted Answer

Turning on the Epson WorkForce WF-2930

To start using your printer, follow these steps:

Unpack the printer and remove all shipping protection elements.
Plug the power cord into an electrical outlet and press the power button located at the front of the device.
The printer will perform an automatic initialization (about 1 to 2 minutes).
Fill the ink cartridges in the appropriate slots (usually black, cyan, magenta, and yellow for this multifunction model).
Load paper into the feed tray up to the maximum fill mark.

Printing with the Epson WF-2930

Three methods are available:

From a computer: Install the Epson printer drivers (available on the Epson website). Open your document, select 'Print' and choose 'Epson WorkForce WF-2930'.
Direct printing: Some models allow direct printing from a USB stick or memory card via the control panel.
Network printing (Wi-Fi): You can connect the printer to your Wi-Fi network to print without a USB cable (configuration required via the device menu).

The control panel has an LCD screen that will guide you through the initial settings. For more specific details, refer to the complete manual on this page.

Question 2

Is the EPSON ACULASER CX17 WiFi or WLAN compatible?

Accepted Answer

No, the EPSON ACULASER CX17 is not WiFi or WLAN compatible.

The CX17 is an entry-level monochrome laser printer that only has wired connectivity:

USB Connection - Standard USB port for direct connection to a computer
Ethernet Network - Wired network connection via RJ45 port (on some variants)

If you need a wireless EPSON printer in the same range, the model ACULASER CX17NF or ACULASER CX17WF (the

Question 3

The motor runs but the feed tray or photo tray does not move

Accepted Answer

If the motor of your EPSON EXPRESSION PHOTO XP-750 runs but the tray (paper or photo) does not move, it is generally a mechanical drive issue.

Preliminary checks:

Completely turn off the printer - press and hold the power button for 10 seconds, then restart
Check for blockages - ensure that no paper, photo, or debris is blocking the feed path or the removable CD/DVD tray (if applicable)
Check the side guides - on the XP-750, the removable paper units have side guides; make sure they are not blocked or misaligned
Never force - do not attempt to manually move the tray if the motor is running, as you could damage the gears

If after these checks the motor continues to run but the tray remains stationary, the drive system (belt, gears, or mechanical coupler) is likely damaged and requires professional repair. Contact EPSON support with the model number XP-750 for assistance or a repair quote.

Question 4

The output tray does not deploy

Accepted Answer

The output tray of the EPSON EXPRESSION PHOTO XP-750 is designed to open automatically during printing. If the tray does not extend, here are some points to check:

First of all

Check for any objects on the tray - The manual states: "make sure nothing is placed on the output tray." Even a small object can block the mechanism.
Clear the space in front of the printer - The tray needs free space to fully deploy when ejecting paper.

During printing

Check that the printer is operational - According to the manual, paper is automatically ejected "after a certain time." Wait for the end of the printing cycle before concluding that the tray is stuck.
Test with a single sheet - Try with a simple document and standard paper to eliminate issues related to paper type or print format.

If the problem persists

A tray that remains stuck despite these checks may indicate an internal mechanical problem (gear, tray motor). Refer to the troubleshooting section of the complete user guide or contact EPSON support.

Question 5

How do I remove the alert message asking to remove the waste paper box if it is empty?

Accepted Answer

On the Epson SureLab SL-D1000 printer, the waste paper box collects the scraps of paper cut during printing on roll paper. The printer has a detection system to monitor the filling of this box and displays an alert when it is time to empty it. If you receive an alert message while the box is empty or insufficiently filled, it is possible that the sensor is malfunctioning.

Sensor reset procedure:

Make sure the printer's power light is on (and not blinking).
Locate the waste paper box on the right side of the printer.
Remove the waste paper box by pulling it forward until it clicks.
Once the box is removed, the status light blinks: this is normal.
Reinsert the waste paper box completely until you hear a locking click.
Wait a few seconds and check that the status light turns off.

This action resets the filling sensor. If the alert message disappears, the issue was a simple desynchronization of the sensor.

Checking the alert threshold:

If you do not want to be alerted so frequently, you can adjust the alert threshold via the control panel menu. Go to Settings > Paper Settings > Remaining Alert and set the numeric value according to your preferences.

If the problem persists:

The waste paper box sensor may be defective. This can also happen if the sensor remains dirty. In this case, you can try gently cleaning the sensor (box insertion area) with a dry cloth. If the message continues to appear despite removal-reinsertion and after resetting, contact Epson technical support or an authorized dealer for sensor replacement or technical assistance.

Question 6

What are the error codes and error messages for the EPSON TM-U220?

Accepted Answer

Error Indicators and Troubleshooting

The EPSON TM-U220 does not have a comprehensive list of alphanumeric error codes. The printer primarily indicates problems through a ERROR light that turns on or blinks.

When the ERROR light is on

Paper roll finished - Check and replace the paper roll
Paper compartment cover open - Close the cover properly
Printer offline - Check connections and power supply

When the ERROR light is blinking

A blinking ERROR light generally indicates:

Abnormal printing temperature - Too high or too low (wait a few minutes or restart)
Paper compartment not secured - Ensure all components are properly positioned
Automatic paper cutter jammed - Clear the mechanism of any obstruction
Paper jam - Open the printer and remove any stuck paper

If the problem persists after checking these points, refer to the detailed troubleshooting in the manual provided with the device.

Question 7

Where can I find a detailed exploded view of the EPSON SureColor SCS80600L printer?

Accepted Answer

A detailed exploded view of the EPSON SureColor SCS80600L printer allows you to visualize the different parts and components of the device, which is useful for maintenance or repair.

To obtain this exploded view:

Check the technical documents provided by EPSON, often available on their official website in the support or download section.
Look for service manuals or maintenance guides specific to this model, which generally contain exploded diagrams.
If not available online, contact EPSON customer service or an authorized service center to request this information.

These detailed exploded views are not always included in consumer user manuals, but they are essential for technicians and can be provided upon request.

Question 8

What does the 'K' indicator flashing on the EPSON ACULASER C1700 printer mean and how can I resolve this issue?

Accepted Answer

When the "K" indicator is flashing on your EPSON ACULASER C1700 printer, it generally means that the black toner (K for "Black") is almost empty or empty. Here’s how to resolve this issue:

Steps to follow:

Check the toner level: Check your printer's menu or the print management software on your computer to find out the remaining black toner level.
Replace the black toner cartridge: If the toner is empty or almost empty, replace the cartridge with one compatible with the ACULASER C1700 model.
Reset the printer: After replacing the cartridge, turn the printer off and then back on to reset the indicator and check that the flashing has stopped.
Check for other causes: If the problem persists, ensure that the cartridge is properly installed and that the contacts are clean. Sometimes, a poor contact can cause flashing.

By following these steps, you should be able to resolve the issue related to the flashing "K" indicator on your EPSON ACULASER C1700 printer.

Question 9

How to resolve the message "No signal input A" on the EPSON EMP-TW10 projector connected to a laptop via HDMI/VGA?

Accepted Answer

If your EPSON EMP-TW10 projector displays the message "No signal input A" while your laptop is connected via an HDMI or VGA cable, here are several steps to follow to resolve this issue:

1. Check the connections

Make sure the HDMI or VGA cable is properly connected to both the laptop and the projector.
If you are using an HDMI to VGA adapter, ensure it is properly connected and functional.

2. Select the correct input source on the projector

Use the remote control or the buttons on the projector to select the source corresponding to the port used (HDMI or VGA).
On the projector, press the Source or Input button and choose the correct input.

3. Configure the display on your laptop

On Windows, press Windows + P to open the display options.
Select Duplicate or Extend to enable projection on the projector.

4. Test the hardware

Try another HDMI or VGA cable to rule out a faulty cable.
Test the HDMI/VGA adapter with another device if possible.

5. Restart the devices

Turn off and then turn on your laptop and the projector to reset the connection.

6. Check the display resolution

Ensure that your laptop's resolution is compatible with the projector.
If necessary, reduce the resolution in your laptop's display settings to test if this resolves the issue.

By following these steps, you should be able to resolve the message "No signal input A" and display your laptop's image on the EPSON EMP-TW10 projector.

Question 10

How to connect a laptop to the EPSON EMP-TW10 projector via an HDMI/VGA adapter?

Accepted Answer

To connect your laptop to the EPSON EMP-TW10 projector using an HDMI to VGA adapter, follow these steps:

1. Checking physical connections

Plug the HDMI/VGA adapter into the HDMI port of your laptop.
Connect the VGA cable from the adapter to the VGA port of the projector.
Make sure all connections are secure and in place.

2. Selecting the source on the projector

Turn on the EPSON EMP-TW10 projector.
Use the "Source" button on the control panel or remote to select the VGA input, which corresponds to the adapter connection.

3. Configuring the display on the laptop

On Windows: Press Windows + P and choose the desired display option (Duplicate, Extend, or Second screen only).
On Mac: Go to System Preferences > Displays and configure the external display.

4. Adjusting the resolution

If the image does not display correctly or is distorted, check and adjust your PC's resolution to be compatible with that of the projector (usually 1024x768 or 1280x720 for a standard model).

5. Transmitting sound

Note that the HDMI/VGA adapter typically does not transmit sound. If you want to play sound, you will need to connect a separate audio cable between your PC and an external audio source.

By following these steps, you should be able to use your EPSON EMP-TW10 projector with your laptop via an HDMI/VGA adapter without difficulty.

User manual EPSON : user manuals and guides in PDF

Models EPSON most viewed

Browse manuals EPSON by appliance type

Recent questions about devices EPSON