Q: Why does the battery of the AEG Boomerang 10 phone discharge quickly?

The AEG Boomerang 10 cordless phone is equipped with 2 rechargeable AAA NiMH batteries of 1.2 V, 650 mAh each . A rapid discharge can have several causes: Possible causes and solutions Battery not charged enough initially - During the first use, leave the handset on the base for 15 full hours for optimal initial charging. Incomplete charging reduces battery life. Worn or old batteries - NiMH batteries degrade over time. If the phone is more than 2-3 years old, the original batteries may have reached their recharge cycle limit. Replace them with new AAA NiMH batteries of at least 650 mAh . Intensive use - The active communication time is 13 hours , but it decreases quickly with use. Standby shows better battery life (230 hours). Ambient temperature - The phone operates optimally between 0°C and 40°C . A temperature that is too low or too high reduces battery performance. Improper charging - Ensure that the handset is correctly positioned on the base (a double beep and a light indicator should activate). Poor contact prevents charging. Make sure to use only the provided or compatible rechargeable NiMH batteries . Standard alkaline batteries are not suitable and may damage the device.

Q: What does the flashing green light on the AEG POWERBASE 60 charger mean?

The flashing green light on your AEG POWERBASE 60 charger indicates a specific condition related to the battery status. According to the official manual, this light can have three different meanings: Solid green light: Fast charging is proceeding normally (temperature between 0°C and 45°C). Flashing green light: The battery is either too hot, too cold, or fully charged in maintenance charge mode. Battery too hot (above 45°C): When the light flashes for this reason, the charger automatically switches to maintenance charge mode to protect the battery. Remove it from the charger and allow it to cool naturally to room temperature until it drops below 45°C. Then reinsert it into the charger: normal charging will automatically resume. Battery too cold (below 0°C): If the battery is too cold, no charging occurs initially. Simply leave the battery in the charger: it will gradually warm up due to maintenance charge mode, and charging will automatically restart without any action required from you. Battery fully charged: Once charging is complete (usually between 10 and 60 minutes depending on the 1.4 Ah capacity), the charger switches to maintenance charge mode, indicated by the flashing light. In this state, the battery maintains its maximum capacity and can remain connected to the charger indefinitely without risk of overcharging. You can therefore leave your AEG POWERBASE 60 battery in the charger permanently, ensuring it is always ready for use.

Q: What to do in case of a water admission error on the AEG FSE83617P dishwasher?

The water admission error (codes i10 or i11) means that your AEG FSE83617P is not filling up correctly. Here’s how to diagnose and resolve the issue: Checks to perform in order Water supply tap - Make sure it is fully open Water pressure - The minimum required pressure is 0.5 bar . If it is lower, contact your water supplier Water supply hose - Check that it is not twisted, bent, or damaged Hose filter - Ensure that the water supply filter is not blocked by deposits or debris Water tap - Check that the connection point to the tap is not obstructed Tip: If you have recently had new plumbing installed or if the water was turned off for maintenance, let the tap run for a few minutes (until it is clear) before reconnecting the dishwasher to eliminate any debris in the pipes. If the problem persists after these checks, contact an authorized AEG service center with your appliance's PNC number (visible on the nameplate inside the door).

Q: How to adjust the cutting depth on the AEG PS 254 L jigsaw?

Your AEG PS 254 L is a radial saw (sliding compound miter saw). To adjust the cutting depth, you need to use the adjustment system consisting of two parts: the adjustment knob (part no. 28) and the cutting depth adjustment plate (part no. 27) . These elements allow you to adjust the height of the blade relative to the workpiece. Adjustment procedure: Before any handling, unplug the saw from the power supply and wait for the blade to come to a complete stop. Locate the cutting depth adjustment knob (no. 28) located on the side of the saw. Release this knob (unlock it if necessary). Position the adjustment plate (no. 27) to the desired depth, depending on the thickness of your material. Tighten the adjustment knob firmly to lock the position. Cutting capabilities: Your PS 254 L radial saw can cut pieces up to 90 mm deep at a 0° miter and bevel angle. This depth varies depending on whether you are making cuts with miter angles or bevel cuts. Refer to the product specifications for other angle configurations. Important tip: After each depth adjustment, perform a test cut without running the motor (by moving the blade) to ensure that nothing interferes with the material and that the depth is correctly set. This check ensures safe and precise operation.

Question 1

Why does the battery of the AEG Boomerang 10 phone discharge quickly?

Accepted Answer

The AEG Boomerang 10 cordless phone is equipped with 2 rechargeable AAA NiMH batteries of 1.2 V, 650 mAh each. A rapid discharge can have several causes:

Possible causes and solutions

Battery not charged enough initially - During the first use, leave the handset on the base for 15 full hours for optimal initial charging. Incomplete charging reduces battery life.
Worn or old batteries - NiMH batteries degrade over time. If the phone is more than 2-3 years old, the original batteries may have reached their recharge cycle limit. Replace them with new AAA NiMH batteries of at least 650 mAh.
Intensive use - The active communication time is 13 hours, but it decreases quickly with use. Standby shows better battery life (230 hours).
Ambient temperature - The phone operates optimally between 0°C and 40°C. A temperature that is too low or too high reduces battery performance.
Improper charging - Ensure that the handset is correctly positioned on the base (a double beep and a light indicator should activate). Poor contact prevents charging.

Make sure to use only the provided or compatible rechargeable NiMH batteries. Standard alkaline batteries are not suitable and may damage the device.

Question 2

How to change the temperature unit (Celsius or Fahrenheit) on the AEG EK7D19S1 freezer?

Accepted Answer

The AEG EK7D19S1 freezer allows you to switch between displaying in Celsius (°C) and Fahrenheit (°F) via the Configuration mode.

Procedure to change the temperature unit:

Press and hold the Extra Cool button for about 3 seconds to activate Configuration mode
Press the Extra Cool button repeatedly until "CF °C" appears on the screen
Press the refrigerator temperature button to toggle between °C and °F
Exit Configuration mode

Freezer temperature range: -15°C to -24°C. The recommended temperature is -18°C for optimal food preservation.

Question 3

What does the flashing green light on the AEG POWERBASE 60 charger mean?

Accepted Answer

The flashing green light on your AEG POWERBASE 60 charger indicates a specific condition related to the battery status. According to the official manual, this light can have three different meanings:

Solid green light: Fast charging is proceeding normally (temperature between 0°C and 45°C).
Flashing green light: The battery is either too hot, too cold, or fully charged in maintenance charge mode.

Battery too hot (above 45°C): When the light flashes for this reason, the charger automatically switches to maintenance charge mode to protect the battery. Remove it from the charger and allow it to cool naturally to room temperature until it drops below 45°C. Then reinsert it into the charger: normal charging will automatically resume.

Battery too cold (below 0°C): If the battery is too cold, no charging occurs initially. Simply leave the battery in the charger: it will gradually warm up due to maintenance charge mode, and charging will automatically restart without any action required from you.

Battery fully charged: Once charging is complete (usually between 10 and 60 minutes depending on the 1.4 Ah capacity), the charger switches to maintenance charge mode, indicated by the flashing light. In this state, the battery maintains its maximum capacity and can remain connected to the charger indefinitely without risk of overcharging. You can therefore leave your AEG POWERBASE 60 battery in the charger permanently, ensuring it is always ready for use.

Question 4

How to remove the air intake filter and the cartridge from the humidifier?

Accepted Answer

Before any intervention, ensure that the device is completely powered off and unplugged from the electrical outlet.

Remove the air intake filter

Start by removing the air intake filter according to the procedure indicated in your user manual.

Remove the cartridge from the humidifier

Locate the fixing screw situated on the top of the humidifier cartridge
Loosen this screw
Pull the cartridge forward, then upward using its handle to completely extract it

Cleaning and reinstallation

Once removed, gently clean these components under a cold water tap with a low flow. Allow them to dry completely before reinstalling. Do not use the device until it is fully reassembled.

Question 5

How to perform a simple spin on the AEG LR63XXL washing machine?

Accepted Answer

To perform a simple spin on your AEG LR63XXL washing machine, you need to use the Spin button located on the control panel.

Procedure:

Press the Spin button repeatedly to decrease or increase the spin speed according to your needs. The speed can go up to 1400 rpm depending on the selected program.
If you want a final spin without draining the water from the last rinse, select the Full Drum Stop option.
For draining and spinning only (without washing), use the Spin/Drain Only cycle.
Once you have made your selection, press the Start/Pause button to start the spin.

If you have chosen an option without final drainage, make sure to press Start/Pause to execute the spin and drainage before opening the door of your appliance.

Question 6

How to turn the oven on and off?

Accepted Answer

To turn on the AEG OK8NW00MB oven:

Select a cooking mode by pressing the dedicated button on the touch control panel
Set the temperature using the +/- sliders or the selection bar
Set the cooking duration by pressing the appropriate button
Press the start button (▷) to begin cooking
Make sure the oven door is properly closed before starting

To turn off the oven:

Press the power button (⏻) to return to standby mode
To immediately cancel an ongoing cooking process, hold the button (⏻) down for 3 seconds

The manual recommends turning off the appliance after each use.

Question 7

What to do in case of a water admission error on the AEG FSE83617P dishwasher?

Accepted Answer

The water admission error (codes i10 or i11) means that your AEG FSE83617P is not filling up correctly. Here’s how to diagnose and resolve the issue:

Checks to perform in order

Water supply tap - Make sure it is fully open
Water pressure - The minimum required pressure is 0.5 bar. If it is lower, contact your water supplier
Water supply hose - Check that it is not twisted, bent, or damaged
Hose filter - Ensure that the water supply filter is not blocked by deposits or debris
Water tap - Check that the connection point to the tap is not obstructed

Tip: If you have recently had new plumbing installed or if the water was turned off for maintenance, let the tap run for a few minutes (until it is clear) before reconnecting the dishwasher to eliminate any debris in the pipes.

If the problem persists after these checks, contact an authorized AEG service center with your appliance's PNC number (visible on the nameplate inside the door).

Question 8

How to adjust the cutting depth on the AEG PS 254 L jigsaw?

Accepted Answer

Your AEG PS 254 L is a radial saw (sliding compound miter saw). To adjust the cutting depth, you need to use the adjustment system consisting of two parts: the adjustment knob (part no. 28) and the cutting depth adjustment plate (part no. 27). These elements allow you to adjust the height of the blade relative to the workpiece.

Adjustment procedure:

Before any handling, unplug the saw from the power supply and wait for the blade to come to a complete stop.
Locate the cutting depth adjustment knob (no. 28) located on the side of the saw.
Release this knob (unlock it if necessary).
Position the adjustment plate (no. 27) to the desired depth, depending on the thickness of your material.
Tighten the adjustment knob firmly to lock the position.

Cutting capabilities: Your PS 254 L radial saw can cut pieces up to 90 mm deep at a 0° miter and bevel angle. This depth varies depending on whether you are making cuts with miter angles or bevel cuts. Refer to the product specifications for other angle configurations.

Important tip: After each depth adjustment, perform a test cut without running the motor (by moving the blade) to ensure that nothing interferes with the material and that the depth is correctly set. This check ensures safe and precise operation.

Question 9

Why is the touch panel not displaying and how do I turn off the light that stays on?

Accepted Answer

Your AEG GDP869PB hood features a touch control panel with illuminated symbols (On/Off, Speeds 1-3, Lighting, etc.). If these symbols are not displaying, it usually means that the panel is not powered or is in standby mode.

Reactivating the touch panel

Check that the metal drawer of the hood is fully extended - some modern hood models disable the panel if the filter is not in the open position.
Press the On/Off symbol on the panel. If the symbols remain invisible but the panel responds, it means the display is active but the symbols' LEDs are not lighting up (minor display issue).
Cut the main power to the hood (circuit breaker) for 30 seconds, then turn it back on. This restart resets the electronic system and often resolves touch panel bugs.

Turning off the light

The light operates independently of the rest of the appliance. According to your manual, the lighting symbol allows you to change the color temperature (neutral, warm, or cool). Try pressing this symbol several times or hold it down for a few seconds to find the complete off mode (some AEG models offer a long press to turn off).

If the hood still does not ventilate

Clean the metal filters - they get dirty quickly and can block ventilation. You can wash them in the dishwasher (short cycle, low temperature).
If after resetting the panel and cleaning the filters the hood still does not respond beyond the lighting, it is likely an electronic failure. Contact the authorized AEG service.

Question 10

What is the price of the door latch for the AEG F78022VI0P dishwasher in euros?

Accepted Answer

The door latch for the AEG F78022VI0P dishwasher has the original part number 1522344058. In France, on the official site shop.aeg.fr, this latch is sold for 9.27 euros (discounted from 10.90 euros, which is a 15% reduction). It is an original AEG spare part that ensures compatibility and quality for your dishwasher model.

This latch ensures the secure closure of the door during all washing cycles and prevents water leaks. It is an essential component of your appliance's closing and locking system. AEG recommends using original spare parts to maintain the optimal performance of your dishwasher.

To purchase this part, visit the official AEG France store (shop.aeg.fr) where it is currently in stock. You can also check specialized retailers for spare parts like Spareka or SOS-Accessoire. Before proceeding with the purchase, check the compatibility of the part by entering the PNC number (11 digits) of your dishwasher found on the nameplate of your appliance.

User manual AEG : user manuals and guides in PDF

Models AEG most viewed

Browse manuals AEG by appliance type

Recent questions about devices AEG