Q: How do I maintain and care for my HiKOKI WR36DB screwdriver?

Regular Inspection Socket: Regularly inspect the wear of the hexagonal or square threaded holes. A worn or deformed socket compromises tightening and reduces torque. Replace it if necessary. Fixing Screws: Regularly check all fixing screws and ensure they are tight. Immediately tighten any loose screws to avoid hazards. Motor and Terminal Maintenance Protect the motor winding by carefully ensuring it is not damaged and/or wet from oil or water. Regularly clean the terminals of the tool and battery. Remove any chips or dust that have accumulated on the terminals. Check before, during, and after use. External Cleaning Use a dry, soft cloth. For stubborn dirt, wipe with a cloth dampened with soapy water. Avoid solvents and thinners that damage plastics. Storage Store your screwdriver in a dry place at less than 40 degrees Celsius, out of reach of children.

Question 1

What filter bags should I buy for the HiKOKI RP200SL vacuum cleaner?

Accepted Answer

The HiKOKI RP200SL offers two options for filter bags suitable for your use:

Non-woven filter bag: recommended for applications generating a small amount of fine dust
PE (polyethylene) disposal bag: advised for applications generating a large amount of fine dust

The device has a 20-liter collection container. Replacement bags must be original HiKOKI models compatible with this model. Check the part number in the manual to order the bag suitable for your type of use.

Question 2

Where can I find the parts diagram (exploded view) for the HiKOKI C10RJ saw to order spare parts?

Accepted Answer

The detailed spare parts diagram (exploded view) for the HiKOKI C10RJ saw is included in the manual through two key documents:

1. Figure 2 - Parts included in the packaging: This figure lists the 22 items provided with the machine (assemblies, accessories, and tools): mobile table saw (A), stand (B), guard blade assembly (C), anti-kickback claws (D), output support assembly (E), rip fence (F), stop (G), support chassis assembly (H), wheel shaft (I), wheel (J), foot assembly (K), handle assembly (L), screws M8 x 45 (M), lock nuts (N-R), hex keys (T-V), and other screws. Refer to this figure to identify the exact references and quantities when restocking.

2. Internal exploded diagram: The manual contains a detailed diagram numbered from 1 to 49 that identifies all internal and external components of the machine (blade, bearings, handles, locking levers, cutting guides, switches, etc.). Each part has a reference number that allows you to order exactly what you need.

Ordering procedure:

Locate the faulty component on one of the two diagrams in the HiKOKI C10RJ manual
Note the exact reference number (for example: blade ø254 mm × ø30 mm, screw M8 x 45, lock nut M10, etc.)
Contact an authorized HiKOKI dealer in France or online with your machine's serial number (indicated on the nameplate)
Request the identical replacement parts HiKOKI bearing the reference number in the diagram

Important: The HiKOKI manual clearly states that only identical spare parts should be used for repairs. For any specific part you cannot find, a HiKOKI dealer can advise you by referring to the complete technical documentation.

Question 3

How to change the cutting line of the HiKOKI CG36DA lawn mower

Accepted Answer

Replacing the cutting line of your HiKOKI CG36DA (string trimmer) involves several simple steps:

Preparation

Obtain 4 m of genuine nylon line (code no. 335235 if you take the original HiKOKI spool).

Replacement procedure

Remove the cover: Press on the opposite tabs of the chassis, then remove the cover.
Remove the spool: Take the spool off the chassis.
Wind the line: Unwind about 150 mm of line on each side, fold the center and attach it to the hook of the spool. Then wind the line onto the spool in the direction indicated by the arrow.
Secure the stop: Leave between 100 mm and 150 mm of unwound line, then hook and secure the line in the stop.
Insert the spool: Reinsert the spool aligning the stop with the eyelet of the line guide, insert the button and thread the line.
Close the cover: Press the tabs of the chassis to snap them into the locking holes.
Cut the line to length: Pull the line to ensure it is taut, then cut it to a length of 90 mm to 110 mm.

Your lawn mower is ready for use.

Question 4

How to change the cutting line of the HiKOKI CG36DA lawn mower

Accepted Answer

Replacing the cutting line of your HiKOKI CG36DA (string mower) is done in several simple steps:

Preparation

Get 4 m of genuine nylon line (code no. 335235 if you take the original HiKOKI spool).

Replacement procedure

Remove the cover: Press on the opposite tabs of the chassis, then remove the cover.
Remove the spool: Take the spool off the chassis.
Wrap the line: Unwind about 150 mm of line on each side, fold the center and attach it to the hook of the spool. Then wrap the line around the spool in the direction indicated by the arrow.
Secure the stop: Leave between 100 mm and 150 mm of unwound line, then hook and secure the line in the stop.
Insert the spool: Reinsert the spool aligning the stop with the line guide eyelet, insert the button and thread the line.
Close the cover: Press on the tabs of the chassis to snap them into the locking holes.
Cut the line to length: Pull the line to make it taut, then cut it to a length of 90 mm to 110 mm.

Your lawn mower is ready for use.

Question 5

How do I maintain and care for my HiKOKI WR36DB screwdriver?

Accepted Answer

Regular Inspection

Socket: Regularly inspect the wear of the hexagonal or square threaded holes. A worn or deformed socket compromises tightening and reduces torque. Replace it if necessary.

Fixing Screws: Regularly check all fixing screws and ensure they are tight. Immediately tighten any loose screws to avoid hazards.

Motor and Terminal Maintenance

Protect the motor winding by carefully ensuring it is not damaged and/or wet from oil or water.

Regularly clean the terminals of the tool and battery. Remove any chips or dust that have accumulated on the terminals. Check before, during, and after use.

External Cleaning

Use a dry, soft cloth. For stubborn dirt, wipe with a cloth dampened with soapy water. Avoid solvents and thinners that damage plastics.

Storage

Store your screwdriver in a dry place at less than 40 degrees Celsius, out of reach of children.

Question 6

How to replace the blade of the CJ 18DSL jigsaw?

Accepted Answer

Preparation

Turn off the device and disconnect the battery. Important note: do not open the lever while the piston is in motion.

Removal and installation

Use the provided wrench to loosen the blade fixing screw
Remove the old blade and insert the new one, ensuring that the protruding parts of the blade are properly inserted into the blade holder
Make sure the blade is positioned between the groove of the roller
Tighten the fixing screw securely

After replacement

Check that the blade rotates correctly after installation. Select the type of blade according to your material: refer to table 3 of the manual for the appropriate references (wood, metal, plastic).

For more details with visual diagrams, refer to pages 181-183 of the user manual.

Question 7

How to replace the motor brushes (carbon) of the CJ 18DSL jigsaw?

Accepted Answer

The PDF of this manual does not specify the procedure for replacing the motor brushes (carbon). The brushes are internal parts of the motor that are not intended for replacement by the user.

However, here is what you need to know about the brushes of your CJ 18DSL:

Signs of wear: If the motor produces visible sparks, loses power, or makes abnormal noises, the brushes are likely worn.
Recommendation: Have the replacement done by an authorized HiKOKI repair shop. They have the original parts and specialized tools for a safe intervention.
Preventive maintenance: The manual recommends keeping the device clean by regularly wiping it with a dry cloth or one dampened with soapy water. This reduces premature wear of the motor.

User manual HiKOKI : user manuals and guides in PDF

Models HiKOKI most viewed

Browse manuals HiKOKI by appliance type

Recent questions about devices HiKOKI