Q: The battery of my BLAUPUNKT CARLA 190 is not charging, what should I do?

First, check these essential points: Connection order: Always connect the charger to the battery first, then to the wall outlet. When disconnecting, reverse the order: unplug the wall outlet first, then the charger. Charge indicator: The charger's light should change from red to green during charging. If there is no change, there may be an issue with the charger or the battery. Charging temperature: Charge the battery between 0-45 °C. If the ambient air is too cold or too hot, wait for the temperature to return to normal (ideally 15-25 °C). Normal duration: A full charge of the CARLA 190 takes 3 to 4 hours. The LCD screen will display all LED segments lit once the charging is complete. If the problem persists: Check the physical condition of the charger and the cable (no cracks, no burns). Test another electrical outlet to rule out a home power fault. If the battery remains empty despite these checks and the charger's light shows no reaction, the battery or the original Blaupunkt charger is likely defective and needs replacement.

Q: How to turn on the BLAUPUNKT COMFORT 112 NOISE CANCELLING headphones?

To turn on the BLAUPUNKT COMFORT 112 NOISE CANCELLING headphones, you activate the active noise cancellation function. Unlike a standard headset, these headphones do not have a traditional power switch: turning them on corresponds to activating the noise cancellation. Step 1 - Install the AAA batteries: First, make sure that two new alkaline AAA batteries (1.5 V) are properly placed in the battery compartment located on the right earcup . Press the cover until it clicks audibly. The operating time is approximately 70 hours with alkaline batteries. Step 2 - Activate noise cancellation: Locate the ON/OFF sliding switch positioned on the left earcup . Slide it to the ON position. Immediately, the operation indicator lights up red , confirming that noise cancellation is activated and operational. The headset then activates its superior active noise cancellation technology of over 16 dB in the frequency range of 150-250 Hz. Step 3 - Adjust the cancellation level: Once activated, use the ANC LEVEL regulator (rotary knob) also located on the left earcup to adjust the intensity of the noise cancellation to your sound environment and personal preferences. Important points: Without batteries, this headset functions as a simple passive wired audio headset, without noise cancellation. After use, deactivate the noise cancellation by switching the switch back to the OFF position to save the batteries. When the operation indicator stops lighting up, replace the batteries.

Q: How to reset the BLAUPUNKT Bremen SQR 46 DAB car radio?

The BLAUPUNKT Bremen SQR 46 DAB car radio offers several reset methods depending on your needs: Method 1: Reset via the user menu (recommended) This method restores all factory settings of the audio system. Briefly press the MENU button to open the user menu. Turn the rotary knob to select the NORMSET item in the VARIOUS menu (Various settings). Press the rotary knob: the screen displays “ PLEASE CONFIRM ”. Press the rotary knob again to confirm the reset. The car radio will automatically turn off and restart with the original factory settings. Method 2: Reset using the reset hole (front) If your device is frozen or unresponsive, you can use the hardware reset. Locate the small hole marked “ Reset ” on the front of the car radio. Use a thin, pointed object (unfolded paperclip tip, toothpick, or awl). Gently insert this object into the hole and press without forcing for about 3 to 5 seconds . The car radio will reset immediately. Method 3: Reset button (rear) A RESET button is also accessible at the back of the device. Locate the RESET button positioned at the back of the car radio. Press and hold it for about 5 seconds . The car radio will reset to factory settings. Important: Do not apply excessive force to avoid damaging the button or internal connector. A gentle and sustained pressure is sufficient. The reset will resolve malfunctions, incorrect settings, and Bluetooth or DAB/FM tuner connection issues.

Question 1

How to set the time on the BLAUPUNKT microwave 5MA46510?

Accepted Answer

Initial setting (at first startup)

When you connect the microwave for the first time, the display shows "00:00" blinking with a beep. Here’s how to proceed:

Press the + button to adjust the time (between 00:00 and 23:59)
Press the © button to confirm your setting

Change the time later

To change the time after the initial setup:

In standby mode, press and hold the ⊙ button for about 3 seconds
The time display disappears and the time starts blinking
Use the + button to set the new time
Press © to confirm the adjustment

Note: The microwave uses a 24-hour format (00:00 to 23:59).

Question 2

How to disable the demo mode (DEMO) on the BLAUPUNKT BUENOS AIRES 200 car radio?

Accepted Answer

To disable the demo mode (DEMO) on your BLAUPUNKT BUENOS AIRES 200:

Press and hold the MENU (⑤) button for about 2 seconds to open the user menu
Press the AM (⑬) or FM (⑭) button as many times as necessary until you see the “DEMO” option
Press the < (②) or > (③) button to switch to “OFF” (disabled)
Press MENU (⑤) briefly to exit the menu and confirm the change

Note: If the automatic shut-off is activated (setting 20M, 40M, or 60M), the demo mode will be disabled automatically.

Question 3

The battery of my BLAUPUNKT CARLA 190 is not charging, what should I do?

Accepted Answer

First, check these essential points:

Connection order: Always connect the charger to the battery first, then to the wall outlet. When disconnecting, reverse the order: unplug the wall outlet first, then the charger.
Charge indicator: The charger's light should change from red to green during charging. If there is no change, there may be an issue with the charger or the battery.
Charging temperature: Charge the battery between 0-45 °C. If the ambient air is too cold or too hot, wait for the temperature to return to normal (ideally 15-25 °C).
Normal duration: A full charge of the CARLA 190 takes 3 to 4 hours. The LCD screen will display all LED segments lit once the charging is complete.

If the problem persists:

Check the physical condition of the charger and the cable (no cracks, no burns).
Test another electrical outlet to rule out a home power fault.
If the battery remains empty despite these checks and the charger's light shows no reaction, the battery or the original Blaupunkt charger is likely defective and needs replacement.

Question 4

How to turn on the BLAUPUNKT COMFORT 112 NOISE CANCELLING headphones?

Accepted Answer

To turn on the BLAUPUNKT COMFORT 112 NOISE CANCELLING headphones, you activate the active noise cancellation function. Unlike a standard headset, these headphones do not have a traditional power switch: turning them on corresponds to activating the noise cancellation.

Step 1 - Install the AAA batteries: First, make sure that two new alkaline AAA batteries (1.5 V) are properly placed in the battery compartment located on the right earcup. Press the cover until it clicks audibly. The operating time is approximately 70 hours with alkaline batteries.

Step 2 - Activate noise cancellation: Locate the ON/OFF sliding switch positioned on the left earcup. Slide it to the ON position. Immediately, the operation indicator lights up red, confirming that noise cancellation is activated and operational. The headset then activates its superior active noise cancellation technology of over 16 dB in the frequency range of 150-250 Hz.

Step 3 - Adjust the cancellation level: Once activated, use the ANC LEVEL regulator (rotary knob) also located on the left earcup to adjust the intensity of the noise cancellation to your sound environment and personal preferences.

Important points: Without batteries, this headset functions as a simple passive wired audio headset, without noise cancellation. After use, deactivate the noise cancellation by switching the switch back to the OFF position to save the batteries. When the operation indicator stops lighting up, replace the batteries.

Question 5

What should I do if my BLAUPUNKT LAGUNA CD36 radio produces no sound?

Accepted Answer

If your BLAUPUNKT LAGUNA CD36 car radio produces no sound, several elements need to be checked before concluding that there is a fault. Start with the simplest aspect: the volume.

Check the volume setting

The volume is adjustable from 0 (silence) to 66 (maximum). Press button 4 to increase the volume. It is possible that the volume is set to 0 and you think the radio is not working.
Also check the device's startup volume: press the MENU button (button 7), then hold down the arrow keys 8 until "ON VOLUME" appears. This initial volume can be very low. If you have selected "LAST VOL", be aware that there is a maximum safety limit of 38 to protect your hearing.

Check the mute function

If the radio display shows "MUTE", it means that the mute function is activated. Briefly press button 1 to disable this function and restore sound. Also check the mute level by accessing the MENU (button 7) until you reach "MUTE LVL".

Check the selected audio source

The LAGUNA CD36 radio has several sources: FM/AM radio, CD, CD changer, and AUX input. Press the SRC button to switch between these sources and ensure you are listening to the desired source. If you are connected to an external CD player via the AUX input, make sure this input is activated by accessing MENU (button 7) and looking for "AUX ON".

Check the phone mode

If the display shows "PHONE", the car radio has automatically muted because a mobile phone is connected and active. Hang up or disconnect the phone to restore normal sound.

Check electrical connections and speakers

If none of the previous steps work, the problem may stem from a poor connection. Check that the +12V power supply is properly connected to the vehicle's electrical system. Also, ensure that all speaker cables (front left LF+/LF-, front right RF+/RF-, rear left LR+/LR-, rear right RR+/RR-) are properly connected to the corresponding speakers. A faulty connection, even from a single speaker, can prevent the overall operation of the audio system.

Question 6

Can the left needle that holds the base on the Blaupunkt Santa Cruz 370 radio be repaired or replaced?

Accepted Answer

Yes, the left needle of the support frame can indeed be replaced. This needle is part of the DIN fixing mechanism that holds the Blaupunkt Santa Cruz 370 car radio in place in the dashboard. It is a usable part that wears out gradually over time, especially if you regularly remove the device.

There are two solutions to solve this problem:

Replace just the needle: You can contact Blaupunkt or an authorized dealer by providing the model "Santa Cruz 370" to request the replacement part. The left needle is sold separately, but Blaupunkt can guide you to the exact part number.
Replace the entire support frame: This is often the most practical and economical solution. The universal 2 DIN support frame (compatible with the Santa Cruz 370) costs about 10 to 20 euros and is easily found at automotive accessory retailers, on general websites (Amazon, eBay, Conrad), or at specialized automotive stores.

Procedure for replacing the support frame: You will need to remove the car radio from the dashboard using the ISO extraction keys (normally provided or available for free). Once the device is removed, detach the old support frame and plug the new universal frame around the device. This operation is simple and does not require any special electrical skills.

If you wish to keep the original Blaupunkt frame, you can also order just the broken needle from Blaupunkt's customer service by providing your device's serial number. However, given the very affordable prices of universal frames, a complete replacement generally remains the best option.

Question 7

How to safely unplug the BLAUPUNKT hood model 5IX94290?

Accepted Answer

To safely unplug your BLAUPUNKT hood model 5IX94290, follow these simple steps:

Locate the electrical outlet: The hood is usually plugged into an outlet located under the kitchen cabinets or in a nearby closet.
Turn off the hood: Make sure the appliance is turned off and all lights are off before unplugging.
Handle the plug carefully: Grasp the plug by the plastic part, never by the cord, to avoid damaging the power cord.
Pull gently: Remove the plug from the outlet by gently pulling towards you, without forcing.

These precautions ensure your safety and protect your hood from any damage during unplugging.

Question 8

How to clean the interior of the BLAUPUNKT extractor hood model 5IX94290?

Accepted Answer

To maintain the optimal efficiency of your BLAUPUNKT 5IX94290 extractor hood, regular cleaning is essential. Before any intervention, unplug the hood from the power supply to avoid any electrical risk.

The first step is to remove the grease filters. This hood has aluminum filters that are generally clipped or secured by quick-release systems. Refer to your installation manual to locate the attachment points precisely. These filters should be cleaned regularly; an alarm signal will display after 30 hours of operation of the hood to indicate that cleaning is necessary.

To clean the aluminum grease filters, you have two options: wash them in warm soapy water with a soft sponge, or place them in the dishwasher (these filters are dishwasher safe). Rinse them thoroughly and dry them completely before reinstalling. Regular cleaning prevents grease buildup and maintains optimal airflow.

If your hood operates in filter mode, it also has activated carbon filters. These should be washed only once in the dishwasher, and must be replaced after approximately 120 hours of operation (depending on usage). An alarm will signal the need for replacement. In extraction mode, the carbon filter alarm remains disabled.

Next, clean the interior of the hood with a soft cloth or a sponge dampened with warm water and mild detergent. Avoid abrasive products, harsh detergents, or solvents that could damage the interior surfaces. Wipe with a damp cloth to remove soap residues, then dry thoroughly with a clean, dry cloth to avoid limescale marks.

Empty the water collection tray located at the bottom of the hood. This tray has a capacity of 0.7 liters and should be emptied regularly to ensure the proper functioning of the appliance, especially after each filter reset. This operation is imperative to avoid overflow or damage to the equipment.

Once all components are dry, reinstall the filters in their original position, ensuring they are properly secured and clipped. Then plug the hood back in and check its proper functioning by testing the three power levels. Regular maintenance keeps your hood efficient, prolongs its lifespan, and prevents bad odors or electrical overloads.

Question 9

How to reset the BLAUPUNKT Bremen SQR 46 DAB car radio?

Accepted Answer

The BLAUPUNKT Bremen SQR 46 DAB car radio offers several reset methods depending on your needs:

Method 1: Reset via the user menu (recommended)

This method restores all factory settings of the audio system.

Briefly press the MENU button to open the user menu.
Turn the rotary knob to select the NORMSET item in the VARIOUS menu (Various settings).
Press the rotary knob: the screen displays “PLEASE CONFIRM”.
Press the rotary knob again to confirm the reset.
The car radio will automatically turn off and restart with the original factory settings.

Method 2: Reset using the reset hole (front)

If your device is frozen or unresponsive, you can use the hardware reset.

Locate the small hole marked “Reset” on the front of the car radio.
Use a thin, pointed object (unfolded paperclip tip, toothpick, or awl).
Gently insert this object into the hole and press without forcing for about 3 to 5 seconds.
The car radio will reset immediately.

Method 3: Reset button (rear)

A RESET button is also accessible at the back of the device.

Locate the RESET button positioned at the back of the car radio.
Press and hold it for about 5 seconds.
The car radio will reset to factory settings.

Important: Do not apply excessive force to avoid damaging the button or internal connector. A gentle and sustained pressure is sufficient. The reset will resolve malfunctions, incorrect settings, and Bluetooth or DAB/FM tuner connection issues.

Question 10

Why won't my BLAUPUNKT Bremen SQR 46 DAB car radio turn on and how can I resolve this issue?

Accepted Answer

If your BLAUPUNKT Bremen SQR 46 DAB car radio won't turn on, several causes may explain this malfunction. Start by checking the following points in order to quickly identify and resolve the problem.

First, check the vehicle's power supply: Make sure the vehicle's ignition is on (key in the On or Start position). The car radio may not turn on if the ignition is off, as it loses its switched power supply. If the ignition is on but the device does not respond, check that the vehicle's battery is sufficiently charged by looking at the dashboard indicators. A very weak or dead battery will prevent the device from functioning.

Examine the electrical connections: Access the back of the car radio to check the cable connections, especially the permanent positive cable (+12V, pin 4) and the ignition cable (pin 7, Kl.15/Ignition) which must be properly plugged into the connector. Also check the ground connection (pin 8, Ground) which must be securely attached. Visually inspect that the cables are not damaged, torn, or poorly connected. The power cables should have a minimum cross-section of 1.5 mm².

Press the Power/Off button firmly: Press the Power/Off button located on the control panel or use the button on the provided remote control. A short press should turn the device on. Note that if you had intentionally turned off the car radio by holding this button for more than 2 seconds, a simple press will reactivate it.

Reset the device to factory settings: If the car radio remains inactive despite correct power supply, perform a complete reset. Refer to the user menu by accessing the "NORMSET" menu (restoration of factory settings). This operation erases all custom settings but may resolve software freezes. After the reset, the device should turn off and then automatically restart with factory settings.

Check the control panel contacts: If the device still does not respond to the button press, regularly clean the control panel contacts using a soft cloth dampened with cleaning alcohol. Poor conductivity of the contacts may prevent the button from functioning properly.

Consult a specialist: If after following all these steps your car radio still does not turn on, consult a specialized BLAUPUNKT dealer or a professional car installer. They will be able to diagnose an internal hardware problem requiring repair or replacement. Your device is covered by a 2-year manufacturer's warranty that may cover this malfunction.

User manual BLAUPUNKT : user manuals and guides in PDF

Models BLAUPUNKT most viewed

Browse manuals BLAUPUNKT by appliance type

Recent questions about devices BLAUPUNKT