Q: How to set the temperature of the ALPATEC AC 9 E air conditioner?

Temperature setting: Use the + / - buttons (marker M) on the control panel Each press increases or decreases the temperature by 1°C The set temperature is displayed on the LED screen (E) After a few seconds, the screen automatically returns to displaying the ambient temperature Temperature range: You can set the temperature between 16°C and 31°C . Important depending on the mode of use: In Cooling mode: temperature setting available In Dehumidification mode: temperature setting is disabled and adjusts automatically In Ventilation mode: temperature setting has no effect Memory: The air conditioner will automatically resume the last temperature settings upon restarting.

Q: Is it necessary to clean the filter of the ALPATEC AC 9 E air conditioner?

Yes, it is essential to regularly clean the filter of your ALPATEC AC 9 E air conditioner to maintain its optimal performance. Cleaning Frequency Clean the air filter at least every 2 months . A clogged filter significantly reduces the efficiency of the air conditioner. How to clean the filter Before any operation, turn off and unplug the air conditioner Remove the filter holder by making a upward movement Clean it with warm soapy water to remove impurities Allow the filter to dry completely before reinstalling it Replace the filter holder in its original position Important Points Do not use chemical solvents that could damage the filter or the device. The filter is washable with water and can be reused indefinitely. Proper maintenance of the filter ensures the optimal operation of your air conditioner.

Q: What is the purpose of the TIME button on the ALPATEC AC 9 E air conditioner?

The TIME button (marker K on the control panel) allows you to program the delayed start and stop of your ALPATEC AC 9 E air conditioner, up to 12 hours in advance. Program a delayed start (device off but plugged in) Press the TIME button once Set the desired delay using the +/- buttons (from 0.5 to 12 hours) The PROG indicator lights up to confirm the programming The air conditioner will automatically turn on after the defined delay To cancel, set to 00:00 Program a delayed stop (device already in operation) Press the TIME button while the air conditioner is running Set the stop delay using the +/- buttons The PROG indicator lights up The device will automatically stop after this delay To cancel, set to 00:00 Note: The LED screen displays the remaining time before the programmed activation or stop. Adjustments are made in increments of 0.5 hours up to 10 hours, then in increments of 1 hour from 10 to 12 hours.

Q: Does the ALPATEC AC 9 E air conditioner have a drain plug for water evacuation?

Yes, the ALPATEC AC 9 E air conditioner has a drain plug (part 9) at the back of the water evacuation system. This plug is equipped with a sealing gasket and allows for the manual evacuation of water accumulated in the condensate tank. When to use the drain plug? Normally, the evacuation of condensates occurs automatically through the hot air duct (capacity of 48 L/day). However, in very humid environments, a removable collection tank (part 14) captures excess condensates. When this tank is full, the device displays the error E2 on the LED screen and emits alert beeps. Drainage procedure Turn off the air conditioner Place the removable tank under the drain plug Remove the drain plug and its gasket to allow the water to drain Replace the gasket and the plug Restart the device

Question 1

How to use the cooling mode of the ALPATEC AC 9 E air conditioner?

Accepted Answer

The cooling mode of your ALPATEC AC 9 E allows you to cool the ambient air to the desired temperature. Here’s how to use it:

Activating the cooling mode

Plug in the device and press the ON/OFF button to start
Press the MODE button to select the cooling mode (the circular indicator light will turn on)
The device will automatically resume the last settings (mode, temperature, and speed)

Temperature and speed settings

Set the desired temperature using the +/- buttons, between 16°C and 31°C (in increments of 1°C)
The LED screen continuously displays the ambient temperature and the set temperature
Choose the fan speed using the SPEED button: Low, Medium, or High

Power and capacity

This device offers a maximum cooling power of 2360 W (absorbed power 777 W) with an air flow rate of 270 m³/h, ideal for effectively cooling spaces up to 16 m². The refrigerant used is R407C.

Key points

The device must remain in an upright position during operation
The exhaust duct must be properly installed (maximum length 1.5 m)
The condensation drainage is done automatically via the duct

Question 2

How to set the temperature of the ALPATEC AC 9 E air conditioner?

Accepted Answer

Temperature setting:

Use the + / - buttons (marker M) on the control panel
Each press increases or decreases the temperature by 1°C
The set temperature is displayed on the LED screen (E)
After a few seconds, the screen automatically returns to displaying the ambient temperature

Temperature range: You can set the temperature between 16°C and 31°C.

Important depending on the mode of use:

In Cooling mode: temperature setting available
In Dehumidification mode: temperature setting is disabled and adjusts automatically
In Ventilation mode: temperature setting has no effect

Memory: The air conditioner will automatically resume the last temperature settings upon restarting.

Question 3

How to adjust the fan speed of the ALPATEC AC 9 E air conditioner?

Accepted Answer

The fan speed adjustment of your ALPATEC AC 9 E air conditioner is very simple via the control panel.

How to adjust the speed

Press the SPEED (J) button on the control panel
Each press toggles the speed in this order: SLOW - MEDIUM - FAST - SLOW
Three indicator lights show you the active speed:
- Slow Indicator (B): minimum speed
- Medium Indicator (C): intermediate speed
- Fast Indicator (D): maximum speed

Important - Dehumidification Mode

In dehumidification mode, the fan speed cannot be adjusted manually - it adjusts automatically according to the needs of the device.

In ventilation mode only, you can freely change the speed with the SPEED button.

Question 4

Is it necessary to clean the filter of the ALPATEC AC 9 E air conditioner?

Accepted Answer

Yes, it is essential to regularly clean the filter of your ALPATEC AC 9 E air conditioner to maintain its optimal performance.

Cleaning Frequency

Clean the air filter at least every 2 months. A clogged filter significantly reduces the efficiency of the air conditioner.

How to clean the filter

Before any operation, turn off and unplug the air conditioner
Remove the filter holder by making a upward movement
Clean it with warm soapy water to remove impurities
Allow the filter to dry completely before reinstalling it
Replace the filter holder in its original position

Important Points

Do not use chemical solvents that could damage the filter or the device. The filter is washable with water and can be reused indefinitely. Proper maintenance of the filter ensures the optimal operation of your air conditioner.

Question 5

What is the purpose of the TIME button on the ALPATEC AC 9 E air conditioner?

Accepted Answer

The TIME button (marker K on the control panel) allows you to program the delayed start and stop of your ALPATEC AC 9 E air conditioner, up to 12 hours in advance.

Program a delayed start

(device off but plugged in)

Press the TIME button once
Set the desired delay using the +/- buttons (from 0.5 to 12 hours)
The PROG indicator lights up to confirm the programming
The air conditioner will automatically turn on after the defined delay
To cancel, set to 00:00

Program a delayed stop

(device already in operation)

Press the TIME button while the air conditioner is running
Set the stop delay using the +/- buttons
The PROG indicator lights up
The device will automatically stop after this delay
To cancel, set to 00:00

Note: The LED screen displays the remaining time before the programmed activation or stop. Adjustments are made in increments of 0.5 hours up to 10 hours, then in increments of 1 hour from 10 to 12 hours.

Question 6

Does the ALPATEC AC 9 E air conditioner have a drain plug for water evacuation?

Accepted Answer

Yes, the ALPATEC AC 9 E air conditioner has a drain plug (part 9) at the back of the water evacuation system. This plug is equipped with a sealing gasket and allows for the manual evacuation of water accumulated in the condensate tank.

When to use the drain plug?

Normally, the evacuation of condensates occurs automatically through the hot air duct (capacity of 48 L/day). However, in very humid environments, a removable collection tank (part 14) captures excess condensates. When this tank is full, the device displays the error E2 on the LED screen and emits alert beeps.

Drainage procedure

Turn off the air conditioner
Place the removable tank under the drain plug
Remove the drain plug and its gasket to allow the water to drain
Replace the gasket and the plug
Restart the device

User manual ALPATEC Air conditioner : user manuals and guides in PDF

Models ALPATEC Air conditioner most viewed

Other categories ALPATEC

Recent questions about Air conditioner ALPATEC