Q: How do I pair my BOOST PS 6000 via Bluetooth?

Here’s how to pair your BOOST PS 6000 with a Bluetooth device: Pairing Steps Activate Bluetooth mode : Press the MODE or BLUE button (on the device or remote) until "BT" appears on the screen. Get close : Place your phone or device within 10 meters of the speaker. Start Bluetooth search : On your device, open Bluetooth settings and start a search for available devices. Select the speaker : Look for "BOOST-PS6000" in the list of detected devices and select it to establish the connection. Control the music : Once paired, you can use the buttons on the speaker or remote (play/pause, next/previous track) to control playback. The speaker features Bluetooth 4.2 technology with a stable range of up to 10 meters. If you encounter difficulties during the search, ensure that your device's Bluetooth is turned on and that the speaker is in search mode ("BT" indicator visible).

Q: How to reset the BOOST PS 6000 speaker?

To reset your BOOST PS 6000 speaker, follow these steps: Unplug the device from its power source for about 10 seconds Then plug it back in This performs a complete software reset of the device and restores its default settings. Note: If the speaker enters sleep mode (after 30 minutes of inactivity), make sure it is properly powered before proceeding with a reset.

Q: How to replace the charger of the BOOST STUPDJ10 speaker?

The charger included with your BOOST STUPDJ10 speaker is a power adapter that converts alternating current 220-240V AC (50/60 Hz) into direct current 15V DC via a 15V DC jack at the back of the device. The speaker is not equipped with a battery and must remain plugged into the mains. Replacement charger specifications: Input voltage: 220-240V AC, 50/60 Hz Output voltage: 15V DC Connector type: 15V DC Jack Where to find a replacement adapter: Universal 15V DC adapters available on major online retail sites (Amazon, Cdiscount, Darty, etc.) or on specialized electronic spare parts sites (PCDT.fr, Fixpart.fr, etc.). Contact BOOST support directly through their official website to obtain the original adapter suitable for this model. Installation advice: Ensure that the 15V DC Jack connector of your new adapter matches exactly with that of your speaker and respect the polarity (usually positive in the center).

Question 1

How do I pair my BOOST PS 6000 via Bluetooth?

Accepted Answer

Here’s how to pair your BOOST PS 6000 with a Bluetooth device:

Pairing Steps

Activate Bluetooth mode: Press the MODE or BLUE button (on the device or remote) until "BT" appears on the screen.
Get close: Place your phone or device within 10 meters of the speaker.
Start Bluetooth search: On your device, open Bluetooth settings and start a search for available devices.
Select the speaker: Look for "BOOST-PS6000" in the list of detected devices and select it to establish the connection.
Control the music: Once paired, you can use the buttons on the speaker or remote (play/pause, next/previous track) to control playback.

The speaker features Bluetooth 4.2 technology with a stable range of up to 10 meters. If you encounter difficulties during the search, ensure that your device's Bluetooth is turned on and that the speaker is in search mode ("BT" indicator visible).

Question 2

How to reset the BOOST PS 6000 speaker?

Accepted Answer

To reset your BOOST PS 6000 speaker, follow these steps:

Unplug the device from its power source for about 10 seconds
Then plug it back in

This performs a complete software reset of the device and restores its default settings.

Note: If the speaker enters sleep mode (after 30 minutes of inactivity), make sure it is properly powered before proceeding with a reset.

Question 3

How to solve a TWS synchronization problem on the BOOST JUPITER 600?

Accepted Answer

If your two BOOST-JUPITER6000 speakers are not synchronizing in TWS (Wireless Stereo) mode, start by checking the essential conditions: make sure both speakers are turned on, properly charged (Li-ion battery 7.4V 3.6Ah), and placed within 10 meters of each other. A low battery prevents the device from maintaining a stable Bluetooth connection.

Next, proceed to TWS pairing. On one of the two speakers (the one you want to use as the main speaker), press and hold the play/pause button until the display shows "SLAU" flashing. This is the signal that the speaker is in TWS pairing mode. The screen will stop flashing once the second speaker has successfully connected. Do not interrupt this step too early.

Once TWS mode is activated on the main speaker, turn on your Bluetooth device (phone, tablet, etc.) and search for available Bluetooth devices. Select "JUPITER6000" from the list of found devices and connect. The two speakers will then play in synchronized stereo.

If synchronization does not work on the first try, completely turn off both speakers, wait at least 5 seconds, then turn them back on and try again. If you had a previous failed attempt, first forget the pairing "JUPITER6000" in your phone's Bluetooth settings before trying again. In case of persistent failure, reset both speakers by simultaneously holding the Power and Volume buttons for about 10 seconds until you see a change on the display, then repeat the entire TWS pairing procedure.

Question 4

How to replace the charger of the BOOST STUPDJ10 speaker?

Accepted Answer

The charger included with your BOOST STUPDJ10 speaker is a power adapter that converts alternating current 220-240V AC (50/60 Hz) into direct current 15V DC via a 15V DC jack at the back of the device. The speaker is not equipped with a battery and must remain plugged into the mains.

Replacement charger specifications:

Input voltage: 220-240V AC, 50/60 Hz
Output voltage: 15V DC
Connector type: 15V DC Jack

Where to find a replacement adapter:

Universal 15V DC adapters available on major online retail sites (Amazon, Cdiscount, Darty, etc.) or on specialized electronic spare parts sites (PCDT.fr, Fixpart.fr, etc.).
Contact BOOST support directly through their official website to obtain the original adapter suitable for this model.

Installation advice:

Ensure that the 15V DC Jack connector of your new adapter matches exactly with that of your speaker and respect the polarity (usually positive in the center).

Question 5

How to resolve a stuck volume issue on the BOOST JUPITER 600 powered speaker?

Accepted Answer

If the volume of your BOOST JUPITER 600 powered speaker is stuck or cannot be increased, several causes may be behind this issue. Here are the steps to resolve it.

Check the physical volume knob. Make sure that the volume knob on the top panel of the speaker is not stuck or damaged. Turn it slowly in both directions to check if it responds correctly. If the knob does not turn freely, this may indicate an obstruction or malfunction of the internal volume potentiometer.

Use the included remote control. The JUPITER 600 offers volume control from the 20-button remote control. The main volume button (button 19) allows you to adjust the sound level from a distance. Ensure that the 2 AAA batteries are correctly installed in the compartment at the back of the remote control. If the volume does not respond to the remote control, replace the batteries and check that the remote control works by pressing other buttons (play, mode, etc.).

Check advanced audio controls. The speaker has EQ, Bass, and Treble controls that can affect the perception of volume. Access the MENU button and follow these steps: press once to display Treble, then turn the volume knob to adjust the high frequencies. Press twice to display Bass and adjust the low frequencies. Ensure that these settings are not at minimum. Also, test the "Mega Bass" mode from the remote control (button 14) which can increase the bass but also affect the overall perceived volume.

Test with different audio sources. Change the audio source (Bluetooth, USB, Micro-SD card, or Line-in input) to check if the problem persists. Also, ensure that the volume on your source device (phone, computer, USB player) is not set to minimum. If one specific source works and another does not, the problem may come from the connected device rather than the speaker.

Check connections and cables. Ensure that all audio cables are properly connected and in good condition. A faulty cable can limit the transmission of the audio signal and affect the ability to change the volume from the source. Make sure that the Line-in input (3.5 mm jack), USB, or any other connector used does not have contact issues.

Reset the speaker. If the speaker is in standby mode, switch it to active mode by pressing the power button or using the remote control. Note that the built-in battery (Li-ion 7.4V 3.6Ah) does not charge in standby mode. Wait 10 minutes after powering on, then test the volume again. If the problem persists, completely unplug the speaker from the power for one minute, then plug it back in and turn it on.

If none of these solutions work, it is possible that the volume potentiometer or an internal component is defective. In this case, a technical diagnosis and repair by a professional are recommended.

Question 6

How to reduce the echo effect on the BOOST Luna 50 amplified speaker?

Accepted Answer

To reduce the echo effect on your BOOST Luna 50 amplified speaker, follow these steps:

Check the speaker controls: On the control panel of the Luna 50, look for a button or setting dedicated to echo, reverb, or sound effects.
Adjust the echo setting: If a button or potentiometer is present, turn it or press it to reduce the intensity of the echo. Generally, turning it to the left decreases the effect.
Test the sound: After making adjustments, listen to the audio output to check that the echo is reduced to your liking.
If no echo setting is available: The echo effect may come from the audio source or the room configuration. Try changing the source or repositioning the speaker to limit natural reverb.

By following these tips, you should be able to control and reduce the echo effect on your BOOST Luna 50 for better sound quality.

Question 7

How to connect a Samsung Galaxy S23 to the BOOST Jupiter 600 amplified speaker?

Accepted Answer

To connect your Samsung Galaxy S23 to the BOOST JUPITER 600 amplified speaker, you have two main options: Wireless Bluetooth connection (recommended for mobility) or 3.5 mm auxiliary cable connection (for a stable wired connection).

Bluetooth Connection (Wireless)

Turn on the JUPITER 600 speaker and press the MODE button on the device or remote until BT appears on the screen. The speaker will then enter Bluetooth pairing mode.
Place your Samsung Galaxy S23 within 10 meters of the speaker for optimal connection.
On your phone, open Settings, select Connections or Bluetooth and enable Bluetooth.
Start searching for available Bluetooth devices. You will see JUPITER6000 appear in the list.
Select JUPITER6000 to establish the connection. Pairing will happen automatically.
Once connected, play your music on the phone. The sound will come from the JUPITER 600 speaker. You can control playback with the buttons on the speaker or with the provided remote control.

Auxiliary Cable Connection (AUX 3.5 mm)

Obtain a 3.5 mm stereo jack cable (standard AUX cable).
Press the MODE button on the speaker or remote until LINE appears. You are now in auxiliary input mode.
Plug one end of the cable into the headphone jack (3.5 mm) of your Samsung Galaxy S23.
Connect the other end of the cable into the Line-in 3.5 mm input of the JUPITER 600 speaker (located on the top of the device).
Turn on or ensure the speaker is in LINE mode (the screen should display “LINE”).
Play your music on the phone. The sound will be immediately output by the speaker.

Practical Tips: The Bluetooth connection is ideal as the JUPITER 600 speaker has a Li-ion battery offering up to 12 hours of battery life in wireless use. You can move freely within a radius of 10 meters. If you encounter connection issues, ensure that Bluetooth is enabled and that the speaker is not in standby mode. The speaker automatically goes into standby after 10 minutes of inactivity.

Question 8

How to resolve the issue when the name of the BOOST STUPDJ10 speaker does not appear during Bluetooth search?

Accepted Answer

If you do not see the name of the BOOST STUPDJ10 speaker when searching for Bluetooth devices, here are several steps to follow to resolve this issue:

1. Check that the speaker is on and in Bluetooth mode

Make sure the speaker is turned on.
Activate Bluetooth mode on the speaker by pressing the dedicated button. A light indicator should confirm that Bluetooth mode is active and the speaker is ready to pair.

2. Proximity and interference

Place your device (smartphone, tablet, etc.) close to the speaker, ideally within 10 meters.
Avoid obstacles or interference that may disrupt the Bluetooth connection.

3. Restart the devices

Turn off and then turn on the speaker to reset the Bluetooth function.
Also restart your device to eliminate any temporary bugs.

4. Check existing Bluetooth connections

If the speaker is already connected to another device, disconnect it from that device so that it is visible to your device.

5. Reset the speaker

If the problem persists, perform a factory reset of the speaker. This operation will remove all previous connections and start with a clean configuration.

By following these tips, you should be able to see and connect your device to the BOOST STUPDJ10 speaker via Bluetooth without difficulty.

Question 9

How to use the BOOST STUPDJ10 powered speaker?

Accepted Answer

The BOOST STUPDJ10 powered speaker is a 500W DJ box equipped with 2 10-inch (25 cm) speakers. It allows you to play music from various sources: Bluetooth, USB, micro-SD, FM radio, or auxiliary line. It also includes a wireless microphone, a remote control, and recording and karaoke features.

Powering on and electrical connection: Plug the speaker into a power outlet (220-240V AC, 50/60Hz) using the supplied adapter (15V DC). Press the power button located on the front panel. A blue LED indicator lights up to confirm that the speaker is functioning.

Selecting the audio source: Use the MODE button on the device or the remote control to switch between modes: AUX (line input), USB, micro-SD, FM (radio), or BLUETOOTH. Each press of the button toggles to the next source. The display shows the selected mode.

Bluetooth connection: Press the MODE button until you reach Bluetooth mode. The display shows "blue" blinking. Enable Bluetooth on your phone or device. Search for available devices and select "STUPDJ10". If a password is requested, enter 0000. Once connected, press the PLAY button to start playback. Use the NEXT and PREV buttons to navigate between tracks.

Playback from USB or micro-SD: Insert a USB stick or micro-SD card into the corresponding ports ("plug & play" mode). Press the MODE button to access USB or TF (micro-SD) mode. Compatible files are MP3 and WMA. Use the navigation buttons (PLAY, PAUSE, NEXT, PREV) to control playback. You can activate repeat by pressing once (repeat a track) or twice (repeat all tracks).

FM radio reception: Press the MODE button to select FM mode. The frequency range is 87.5 to 108.0 MHz. For automatic station search, press and hold the PLAY/PAUSE button. Found stations are automatically stored. Navigate between stations using the NEXT and PREV buttons.

Connecting an auxiliary source (AUX): Select AUX mode using the MODE button. Connect your MP3 player, CD player, or any other audio device to the AUX jack. Adjust the main volume to set the sound level.

Using microphones and karaoke: The speaker has two independent microphone inputs. The included wireless microphone connects directly. Adjust the microphone volume with the MIC.VOL button and the echo with the ECHO button. The MIC PRIORITY button automatically reduces the music volume when you speak into the microphone (Talkover function).

Audio recording: Connect a USB stick or micro-SD card. In AUX mode, press the REC button to start. In USB/micro-SD mode, also press REC to record sound from the microphone or any ongoing source. The display shows "00:01" at startup. A folder is automatically created for recordings.

Sound settings: Use the BASS (low) and TREBLE (high) buttons to adjust frequencies. The speaker also offers equalization modes: Rock, Pop, Jazz. Adjust the main volume with the volume control located on the front panel.

Using the remote control: The supplied remote control works up to 6 meters with a 30° angle relative to the speaker. It replicates the main functions: power on/off, MODE, volume +/-, play/pause, next/previous track, recording, repeat, and source selection. Obstacles between the remote control and the sensor reduce the range.

Rear panel connectors: At the back, you will find the AUX IN jack for connecting external audio devices, the microphone priority switch for the Talkover function, and the DC 15V input for the power adapter. On the front panel, you have access to the two microphone inputs, the USB/micro-SD input, volume controls, echo, and bass/treble controls.

Question 10

How to pair two BOOST JUPITER 600 powered speakers for simultaneous use?

Accepted Answer

The BOOST JUPITER 600 features a TWS (True Wireless Stereo) function that allows you to pair two speakers for stereo playback. Here’s how to do it:

Step 1: Activate TWS mode
Turn on both BOOST JUPITER 600 speakers. On one of them, press and hold the play/pause button (located on the top) for several seconds. The screen will display “SLAU” and the indicator will blink continuously. This blinking indicates that the speaker is waiting to sync with the second speaker.

Step 2: Synchronize the speakers
Wait for both speakers to automatically detect each other. This synchronization occurs via Bluetooth and must be done with both speakers nearby (less than 10 meters apart). Once the connection is established between the two speakers, the blinking stops and the display on the first speaker stabilizes.

Step 3: Pairing with your audio source
Turn on your source device (smartphone, tablet, computer). Activate Bluetooth search on it and select “JUPITER6000” from the list of available devices. Once paired, your device is connected to the system of both speakers.

Step 4: Test playback
Start playing music on your source device. The sound should come out simultaneously from both BOOST JUPITER 600 speakers, creating a stereo output. Both speakers will play the same audio content in perfect synchronization.

Important: Ensure that both speakers remain close to each other during pairing in TWS mode (less than 10 meters). Once the pairing is established and the source device is connected via Bluetooth, you can move them a bit further apart, but good proximity ensures better connection stability.

User manual BOOST Powered speaker : user manuals and guides in PDF

Models BOOST Powered speaker most viewed

Other categories BOOST

Recent questions about Powered speaker BOOST