Q: What is the symbol for the rinse and spin program?

The Rinse and Spin program of the TEKA TKX1 600T does not have a distinct specific symbol on the control panel. Instead, it is a full program that you select via the program selection dial located on the control panel. This program allows you to initiate an additional spin of your laundry after a wash, without restarting a full cycle. This is particularly useful when you want to extract more water before drying. To use this program: Turn the program selection dial to the

Q: What does it mean when the power indicator is flashing and the machine does not start?

This symptom corresponds to error code Err 01 on your TEKA TKX1 600T machine. Cause: The door of the machine is not properly closed. The machine has a safety system that prevents the washing cycle from starting until the door is securely locked. Solution Close the door completely until you hear a distinct click - this is the signal that the locking has engaged Ensure that the door is properly in contact with the frame and has no obstructions Press the power button once to restart If the problem persists: Unplug the machine from the power outlet for 30 seconds, then plug it back in. If the indicator continues to flash, contact a certified TEKA technician.

Q: What does error code E02 mean on the TEKA LI5 1280 washing machine and how can it be resolved?

The error code E02 indicates a water filling problem on your TEKA LI5 1280 washing machine. The machine is unable to fill with water properly. Here are the checks to perform in order: Step 1 - Check the water supply Make sure the water supply tap is fully open Check that the water supply hose is not kinked, bent, or blocked Consult the installation to ensure that the drainage connection is at the correct height (minimum 50 cm) Step 2 - Check the inlet filter Close the water supply tap Unscrew the supply hose at the back of the machine Check that the anti-sand filter is not clogged or blocked Clean it if necessary with water or a cloth Reattach the hose Step 3 - Check the filter compartment Inspect the filter compartment for foreign objects (lime, debris) that could obstruct the water flow Clean or replace the filter if necessary If after these checks the E02 code persists, contact the authorized TEKA technical service. The problem may be due to a defective filling solenoid valve or a damaged water level sensor, requiring professional intervention.

Question 1

What is the symbol for the rinse and spin program?

Accepted Answer

The Rinse and Spin program of the TEKA TKX1 600T does not have a distinct specific symbol on the control panel. Instead, it is a full program that you select via the program selection dial located on the control panel.

This program allows you to initiate an additional spin of your laundry after a wash, without restarting a full cycle. This is particularly useful when you want to extract more water before drying.

To use this program:

Turn the program selection dial to the

Question 2

Does a dirty dispenser affect the operation of the TEKA TKX3 1263 washing machine?

Accepted Answer

Yes, a dirty dispenser can affect the operation of your TEKA TKX3 1263. A clogged dispenser prevents the detergent and fabric softener from dissolving properly in water and being distributed at the right times during the cycle.

Problems caused by a dirty dispenser:

Detergent blockage - water cannot dilute and carry the product properly
Residue buildup - detergent remnants get stuck in the drawer
Water leaks - debris can cause abnormal flow during the cycle
Poor rinsing - fabric softener is not distributed at the scheduled time

How to clean the dispenser:

Press the arrows located on the fabric softener lid
Lift the clip and remove the drawer from the dispenser
Clean all grooves and interior cavities with warm water
Gently brush off any dried detergent buildup
Rinse thoroughly and let dry before reinstalling

Your TEKA TKX3 1263 manual recommends periodic cleaning of the detergent drawer to avoid blockages. Additional tip: dilute thick or clumped detergent in a little water before pouring it into the dispenser, especially if using powder doses in humid weather.

Question 3

How do I clean the drainage pump of my TEKA TKX3 1263 washing machine?

Accepted Answer

Here are the steps to clean the drainage pump of your TEKA TKX3 1263:

Preparation

Completely turn off the washing machine and wait for the water to cool down
Open the service panel located at the front base of the appliance
Place a container under the pump to catch any residual water

Cleaning

Gently unscrew the pump cap by turning it counterclockwise
Remove any objects blocking the impeller (coins, buttons, threads, fabrics) - you can manually rotate the impeller to check its proper functioning
Clean the inside if necessary with a damp cloth
Tighten the cap securely
Close the service panel

Important precautions

Never remove the cap while the machine is running or immediately after a cycle - risk of burns from hot water
Ensure that the cap is tightly secured to avoid leaks during the next cycles
Prefer simple tools (screwdriver or wrench if necessary) - do not force if the cap is stuck

Question 4

Where is the drainage pump of the TEKA TKX3 1263 washing machine located?

Accepted Answer

The drainage pump of the TEKA TKX3 1263 is located at the lower front part of the appliance. To access it:

Make sure the washing machine is turned off and unplugged.
Remove the maintenance panel located at the bottom of the front (usually held by screws or clips).
The pump is positioned at the bottom of the motor compartment, near the drainage outlet.
It is easily recognizable by its connections: a drainage hose and electrical connectors.

If you need to replace the pump or access the drainage filter, refer to the maintenance section of the manual for the exact procedure and spare part references.

Question 5

What does it mean when the power indicator is flashing and the machine does not start?

Accepted Answer

This symptom corresponds to error code Err 01 on your TEKA TKX1 600T machine.

Cause: The door of the machine is not properly closed. The machine has a safety system that prevents the washing cycle from starting until the door is securely locked.

Solution

Close the door completely until you hear a distinct click - this is the signal that the locking has engaged
Ensure that the door is properly in contact with the frame and has no obstructions
Press the power button once to restart

If the problem persists: Unplug the machine from the power outlet for 30 seconds, then plug it back in. If the indicator continues to flash, contact a certified TEKA technician.

Question 6

What does error code E02 mean on the TEKA LI5 1280 washing machine and how can it be resolved?

Accepted Answer

The error code E02 indicates a water filling problem on your TEKA LI5 1280 washing machine. The machine is unable to fill with water properly. Here are the checks to perform in order:

Step 1 - Check the water supply

Make sure the water supply tap is fully open
Check that the water supply hose is not kinked, bent, or blocked
Consult the installation to ensure that the drainage connection is at the correct height (minimum 50 cm)

Step 2 - Check the inlet filter

Close the water supply tap
Unscrew the supply hose at the back of the machine
Check that the anti-sand filter is not clogged or blocked
Clean it if necessary with water or a cloth
Reattach the hose

Step 3 - Check the filter compartment

Inspect the filter compartment for foreign objects (lime, debris) that could obstruct the water flow
Clean or replace the filter if necessary

If after these checks the E02 code persists, contact the authorized TEKA technical service. The problem may be due to a defective filling solenoid valve or a damaged water level sensor, requiring professional intervention.

User manual TEKA Washing machine : user manuals and guides in PDF

Models TEKA Washing machine most viewed

Other categories TEKA

Recent questions about Washing machine TEKA