Q: How to disable or reduce the dishwasher's ringing?

Yes, the Candy CDI 2DS36 dishwasher allows you to completely disable the end-of-program ringing . Here is the procedure to follow: Steps to disable the ringing: Start with the dishwasher completely off Press and hold the PROGRAMS button and simultaneously press the ON/OFF button (a brief sound will be heard) Continue to hold the PROGRAMS button for at least 15 seconds (you will hear 2 beeps during this time) Release the button when you hear the 2nd beep . The display will show b1 , indicating that the ringing is currently enabled Press the PROGRAMS button again just once. The display will then show b0 , confirming that the ringing is disabled Turn off the dishwasher by pressing ON/OFF to validate the settings The ringing will then be completely silent at the end of the program. To reactivate the ringing, simply repeat the same procedure: the display will change from b0 to b1 when you press the PROGRAMS button at step 4. Important: This function only controls the end-of-program acoustic signal. Other sound signals (errors, door opening during drying) are not affected.

Q: The dishwasher does not heat the water, I checked the NTC probe and I measure 20K ohm. Is this normal?

No, 20K ohm is a bad sign. A properly functioning NTC probe of the Candy CDI 3615 has a much lower resistance depending on the temperature: Cold water (20°C): 2.5K to 3.5K ohms Warm water (50°C): 1.5K to 2K ohms Hot water (80°C): 500 to 800 ohms The value of 20K ohms that you measure is abnormally high and very likely indicates a defective probe or a poor electrical connection . Steps to follow: Check the connectors: Make sure the probe is properly plugged in and that no corrosion is affecting the connectors. Clean the contacts: Disconnect the probe and clean the connectors with a dry, clean cloth. Re-measure: After cleaning, take the measurement again with your ohmmeter. Replace the probe if necessary: If the resistance remains above 5K ohms, the NTC probe must be replaced. Your dishwasher will display error code E8 or Ei to indicate a heating problem due to a defective or disconnected probe. You can find compatible replacement probes for Candy CDI 3615 from specialized appliance spare parts suppliers, using your device's reference (16 characters starting with 3) found on the nameplate inside the dishwasher.

Q: My dishwasher won't start and beeps twice with all the lights flashing, what should I do?

When your CANDY CS 3E6L0W dishwasher won't start, emits 2 beeps , and all the lights are flashing , it generally indicates a power or locking issue. Here are the checks to perform: Troubleshooting Steps Check the door closure. The dishwasher will only start if the door is properly closed. Open the door completely, then close it firmly until you hear a click. The lights should stop flashing. Reset the appliance. Press the Power/Off button and hold it for 3 seconds to turn off the appliance. Wait 30 seconds, then turn it back on. Select a program and restart the start process. Check the power supply. Ensure that the appliance is properly plugged in. The required power supply is 220-240 V / 50 Hz / 10 A. If the appliance is on a power strip or extension cord, plug it directly into a wall outlet. Check the child safety lock. If the child safety lock is activated (lock symbol), hold the corresponding button for 5 seconds to deactivate it, then try to start again. If after these checks the appliance continues to beep with the lights flashing, it may be an electronic fault. Contact CANDY customer service for a thorough diagnosis.

Q: The P3 code is flashing on my Candy Rapido CF 3E7L0X and I can't configure the programs

Important: The P3 code displayed alone (without abnormal flashing) simply indicates the ECO program operating at 45°C. However, if this code flashes and prevents you from configuring programs, it indicates a problem. Try the following solutions in this order: Reset the device: Completely turn off the dishwasher by pressing the ON/OFF button, wait 30 seconds, then turn it back on. Check the door: Make sure the door is properly closed. If it is not securely latched, the device will not allow you to select a program. Check the water supply: Ensure that the water inlet tap is open and that the device is receiving water. A lack of water can block program selection. Completely empty the device: Open the main filter (at the bottom center) and clean it to remove any debris that may be blocking the sensors. If the P3 flashing persists after these checks, refer to the Troubleshooting section of your manual or contact Candy customer service, as this may indicate an electronic malfunction requiring technical intervention.

Q: What does the P3 code displayed on my Candy Rapido CF 3E7L0X dishwasher mean?

P3 is not an error code , it is the ECO program designation of your Candy Rapido CF 3E7L0X. This program operates at 45°C with a cycle duration of 233 to 236 minutes. If your dishwasher is flashing or showing a persistent light , there may be a real error code. Errors on this model are displayed with the letter E followed by a number (for example E2, E3, E8, etc.). The main error codes for your dishwasher are: E2, E3 : Drainage problem - check that the drain hose is at the correct height and clean the filter E4 : Water leak detected - inspect the hoses E8 : The heating element is not functioning properly or the filter plate is clogged E18 : Water level issues - clean the filter plate E21 : Uncontrolled water supply - immediately close the tap If you see a code with an E, refer to the list above. If your appliance is flashing without displaying a code, check the condition of the filters and hoses.

Question 1

How to disable the end-of-program beep on the CANDY CDI 2DS36 dishwasher?

Accepted Answer

To disable the beep at the end of the program on the CANDY CDI 2DS36, follow these steps:

Turn off the dishwasher using the ON/OFF button
Press and hold the PROGRAMS button while turning on the appliance (a first beep sounds)
Continue to hold PROGRAMS for at least 15 seconds (two beeps will be heard)
Release when the second beep sounds: the display shows b1 (sound currently enabled)
Press PROGRAMS again: the display changes to b0 (sound disabled)
Turn off the appliance to validate the setting

By default, the dishwasher emits a 5-second acoustic signal at the end of the cycle, repeated 3 times every 30 seconds. This procedure completely eliminates these sound notifications. To reactivate the beep later, follow the exact same procedure.

Question 2

How to disable or reduce the dishwasher's ringing?

Accepted Answer

Yes, the Candy CDI 2DS36 dishwasher allows you to completely disable the end-of-program ringing. Here is the procedure to follow:

Steps to disable the ringing:

Start with the dishwasher completely off
Press and hold the PROGRAMS button and simultaneously press the ON/OFF button (a brief sound will be heard)
Continue to hold the PROGRAMS button for at least 15 seconds (you will hear 2 beeps during this time)
Release the button when you hear the 2nd beep. The display will show b1, indicating that the ringing is currently enabled
Press the PROGRAMS button again just once. The display will then show b0, confirming that the ringing is disabled
Turn off the dishwasher by pressing ON/OFF to validate the settings

The ringing will then be completely silent at the end of the program. To reactivate the ringing, simply repeat the same procedure: the display will change from b0 to b1 when you press the PROGRAMS button at step 4.

Important: This function only controls the end-of-program acoustic signal. Other sound signals (errors, door opening during drying) are not affected.

Question 3

What washing programs are available on the Candy CDP 4609 X?

Accepted Answer

The CDP 4609 X is a CANDY dishwasher offering a wide range of programs suitable for different types of dishes and levels of soiling. Although the detailed content of the PDF manual is not directly accessible, this model typically offers:

Eco Program: for minimal water and energy consumption
Normal/Standard Program: for everyday dishes
Intensive Program: for very dirty pots and pans
Delicate Program: for glassware and fine china
Quick Program: for a short and efficient wash
Soak Program: for pre-treating heavily soiled dishes

Each program can generally be adjusted via the control buttons located on the front of the dishwasher. To check the exact specifications of each program (temperature, duration, water and energy consumption), I recommend downloading and consulting the complete manual provided on this page.

Question 4

How much rinse aid should be added to the reservoir?

Accepted Answer

The rinse aid reservoir does not have a precise dosage in ml. It is equipped with an optical indicator that shows you the level:

Dark reflection = FULL reservoir
Light reflection = EMPTY reservoir (to be refilled)

Simply fill the reservoir until you achieve a dark reflection. The reservoir is located to the left of the detergent compartment: press the designated marking and pull the tab upwards to open it.

Dosage adjustment

A dosage slider (positions 1 to 6) is located under the lid and can be adjusted with a coin. Position 4 is recommended.

Adjust according to the results:

Visible deposits on the dishes → decrease by one position
Whitish halos → increase by one position

Only use a specific rinse aid for automatic dishwashers.

Question 5

The dishwasher does not heat the water, I checked the NTC probe and I measure 20K ohm. Is this normal?

Accepted Answer

No, 20K ohm is a bad sign. A properly functioning NTC probe of the Candy CDI 3615 has a much lower resistance depending on the temperature:

Cold water (20°C): 2.5K to 3.5K ohms
Warm water (50°C): 1.5K to 2K ohms
Hot water (80°C): 500 to 800 ohms

The value of 20K ohms that you measure is abnormally high and very likely indicates a defective probe or a poor electrical connection.

Steps to follow:

Check the connectors: Make sure the probe is properly plugged in and that no corrosion is affecting the connectors.
Clean the contacts: Disconnect the probe and clean the connectors with a dry, clean cloth.
Re-measure: After cleaning, take the measurement again with your ohmmeter.
Replace the probe if necessary: If the resistance remains above 5K ohms, the NTC probe must be replaced. Your dishwasher will display error code E8 or Ei to indicate a heating problem due to a defective or disconnected probe.

You can find compatible replacement probes for Candy CDI 3615 from specialized appliance spare parts suppliers, using your device's reference (16 characters starting with 3) found on the nameplate inside the dishwasher.

Question 6

My dishwasher won't start and beeps twice with all the lights flashing, what should I do?

Accepted Answer

When your CANDY CS 3E6L0W dishwasher won't start, emits 2 beeps, and all the lights are flashing, it generally indicates a power or locking issue. Here are the checks to perform:

Troubleshooting Steps

Check the door closure. The dishwasher will only start if the door is properly closed. Open the door completely, then close it firmly until you hear a click. The lights should stop flashing.
Reset the appliance. Press the Power/Off button and hold it for 3 seconds to turn off the appliance. Wait 30 seconds, then turn it back on. Select a program and restart the start process.
Check the power supply. Ensure that the appliance is properly plugged in. The required power supply is 220-240 V / 50 Hz / 10 A. If the appliance is on a power strip or extension cord, plug it directly into a wall outlet.
Check the child safety lock. If the child safety lock is activated (lock symbol), hold the corresponding button for 5 seconds to deactivate it, then try to start again.

If after these checks the appliance continues to beep with the lights flashing, it may be an electronic fault. Contact CANDY customer service for a thorough diagnosis.

Question 7

The P3 code is flashing on my Candy Rapido CF 3E7L0X and I can't configure the programs

Accepted Answer

Important: The P3 code displayed alone (without abnormal flashing) simply indicates the ECO program operating at 45°C. However, if this code flashes and prevents you from configuring programs, it indicates a problem.

Try the following solutions in this order:

Reset the device: Completely turn off the dishwasher by pressing the ON/OFF button, wait 30 seconds, then turn it back on.
Check the door: Make sure the door is properly closed. If it is not securely latched, the device will not allow you to select a program.
Check the water supply: Ensure that the water inlet tap is open and that the device is receiving water. A lack of water can block program selection.
Completely empty the device: Open the main filter (at the bottom center) and clean it to remove any debris that may be blocking the sensors.

If the P3 flashing persists after these checks, refer to the Troubleshooting section of your manual or contact Candy customer service, as this may indicate an electronic malfunction requiring technical intervention.

Question 8

What does the P3 code displayed on my Candy Rapido CF 3E7L0X dishwasher mean?

Accepted Answer

P3 is not an error code, it is the ECO program designation of your Candy Rapido CF 3E7L0X. This program operates at 45°C with a cycle duration of 233 to 236 minutes.

If your dishwasher is flashing or showing a persistent light, there may be a real error code. Errors on this model are displayed with the letter E followed by a number (for example E2, E3, E8, etc.).

The main error codes for your dishwasher are:

E2, E3: Drainage problem - check that the drain hose is at the correct height and clean the filter
E4: Water leak detected - inspect the hoses
E8: The heating element is not functioning properly or the filter plate is clogged
E18: Water level issues - clean the filter plate
E21: Uncontrolled water supply - immediately close the tap

If you see a code with an E, refer to the list above. If your appliance is flashing without displaying a code, check the condition of the filters and hoses.

Question 9

What should I do if the Candy BRAVA dishwasher gets stuck or remains stuck on program 1?

Accepted Answer

If your Candy BRAVA dishwasher is stuck or remains on program 1 (ECO), first try a manual interruption by holding down the START/CANCEL button for 3 seconds. This should stop the current cycle.

If the program does not stop, perform a full restart:

Hold the ON/OFF button for 3 seconds to turn off the appliance
Wait about thirty seconds
Restart by pressing the ON/OFF button again for 3 seconds

If the blockage persists, also check that the tub filters are not clogged (debris, crumbs, dirt). A dirty filter can interrupt or block the cycle. Clean them with clear water.

If after these steps the appliance remains stuck on program 1 and you see a displayed error code (E2, E3, E8, etc.), refer to the Troubleshooting section of this manual for specific code interpretation.

Question 10

How to resolve the message "Wait for conf" on the power button of the Candy RAPIDò CS3E6LOW?

Accepted Answer

The message "Wait for conf" appears when the dishwasher is waiting for confirmation to validate the start of the cycle. This is not a malfunction, but rather a normal startup phase. Here’s how to resolve this issue:

Causes and solutions:

Insufficient pressure on the ON/OFF button ① - Hold the button down longer (about 2-3 seconds) until the program indicator lights up completely and the cycle starts. A simple touch may trigger this waiting message.
Incorrect program selection - Ensure that you have selected a program before pressing ON/OFF. The machine is waiting for confirmation of the selected cycle.
Door not completely closed - Close the dishwasher door firmly and audibly. The waiting message appears if the closure detection is incomplete.
Startup delay - Wait 10-15 seconds after pressing ON/OFF. Some models display this message before automatically confirming and starting the cycle.
Rinsing the water circuit - If this is your first use, the machine performs an automatic rinse of the circuit before truly starting. This may generate this waiting confirmation message.

Important: If the message persists after 20 seconds and the cycle does not start, turn off the device by pressing ON/OFF again, wait 30 seconds, then try again after properly closing the door and selecting a program.

User manual CANDY Dishwasher : user manuals and guides in PDF

Models CANDY Dishwasher most viewed

Other categories CANDY

Recent questions about Dishwasher CANDY