Q: Where is the SET button on the Oregon Scientific BAR928 weather station?

The Oregon Scientific BAR928 weather station does not have a button specifically labeled "SET". The button used to access the setup mode is the MODE button, identified by the letter Y on the front panel diagram. The MODE button is located on the main front panel of the device, in the control area. This is the button that triggers the clock setting mode and allows access to the configuration of the settings. Once the setup mode is activated, you will use the UP and DOWN buttons (W buttons) to adjust the values. To access the settings: Press the MODE button for three seconds when the current time is displayed The time digits will light up and blink Use the UP and DOWN buttons to adjust the hours, then press MODE again to move to the minutes Continue this procedure to set the time, date, and other settings If you need to completely reset the device to factory settings, you will find the RESET button (Z button) inside the battery compartment. This button should only be used if the device is not functioning properly.

Question 1

How to change the time on the Oregon Scientific RM336PES weather station?

Accepted Answer

To change the time on your Oregon Scientific RM336PES weather station, you first need to disable the reception of the radio clock signal, then access the manual setting menu.

Step 1: Disable radio signal reception

Press and hold the - button to disable the reception of the radio clock signal. This step is necessary before you can manually set the time.

Step 2: Access the setting menu

Press and hold the clock setting button (represented by the calendar and clock icon) to enter manual setting mode.

Step 3: Adjust the settings

Use the + and - buttons to change the values. The settings are displayed in this order: time zone, 12/24 hour format, hour, minutes, year, calendar format (day-month or month-day), month, and day. Press the clock setting button to confirm each setting and move to the next.

Time zone setting

Your RM336PES model receives the DCF-77 signal (available in Western Europe, near Frankfurt). The time offset can be set from -23 to +23 hours relative to the received signal. If you have disabled signal reception, you can ignore this setting.

Confirmation and return to normal display

Once all settings have been changed, press the clock setting button one last time to confirm and return to the normal time display. Your clock will now show the correct time in the chosen format (12 or 24 hours).

Question 2

How to calibrate the temperature on the OREGON SCIENTIFIC BAR928 weather station?

Accepted Answer

To calibrate the temperature on your OREGON SCIENTIFIC BAR928 weather station, follow these simple steps:

Steps to calibrate the temperature:

Access calibration mode: Press the SET or MODE button until the display indicates that you are in calibration mode. On some models, you may need to hold the SET button for a few seconds.
Select the temperature to adjust: Use the + or - buttons to navigate to the option regarding the temperature you wish to correct (indoor or outdoor temperature).
Adjust the value: Once the temperature is selected, use the + or - buttons to modify the displayed value so that it matches the actual temperature measured by a reliable thermometer.
Confirm the settings: Press SET or MODE to save the changes and exit calibration mode.
Check accuracy: After calibration, compare the displayed temperature with a reliable source to ensure that the correction is correct.

This procedure helps to correct any measurement discrepancies and improve the accuracy of your weather station.

Question 3

Where is the SET button on the Oregon Scientific BAR928 weather station?

Accepted Answer

The Oregon Scientific BAR928 weather station does not have a button specifically labeled "SET". The button used to access the setup mode is the MODE button, identified by the letter Y on the front panel diagram.

The MODE button is located on the main front panel of the device, in the control area. This is the button that triggers the clock setting mode and allows access to the configuration of the settings. Once the setup mode is activated, you will use the UP and DOWN buttons (W buttons) to adjust the values.

To access the settings:

Press the MODE button for three seconds when the current time is displayed
The time digits will light up and blink
Use the UP and DOWN buttons to adjust the hours, then press MODE again to move to the minutes
Continue this procedure to set the time, date, and other settings

If you need to completely reset the device to factory settings, you will find the RESET button (Z button) inside the battery compartment. This button should only be used if the device is not functioning properly.

Question 4

How do I set the date and time on the OREGON SCIENTIFIC BAR928 weather station?

Accepted Answer

The Oregon Scientific BAR928 weather station allows you to easily set the date and time using the MODE, UP, and DOWN buttons located on the main unit. The process is divided into two steps: setting the time and setting the calendar.

To set the time:

When the current time display is visible, press the MODE button for 3 seconds to enter setting mode.
The 12h/24h format numbers will blink first. Use the UP or DOWN buttons to select your preferred format, then press MODE.
The hour numbers will blink. Use UP or DOWN to enter the hour. You can hold the button down to scroll quickly through the values.
Press MODE to move to the minutes.
Set the minutes in the same way as the hours using UP or DOWN.
Press MODE one last time to confirm and exit setting mode.

To set the calendar:

When the calendar display is visible, press the MODE button for 3 seconds.
The altitude compensation value will blink first. Set it to 0 for a standard barometric pressure reading, or enter your altitude (-100 to 2500 meters) if you live in the mountains.
Press MODE. The year numbers will blink. Enter the year using UP or DOWN.
Press MODE. The D or M indicator will blink to select the date format: D for day-month or M for month-day.
Press MODE and set the month, then the day of the month in the same way.
Press MODE. The language indicator will blink (E, I, D, F, or S). Select F for French using UP or DOWN.
Press MODE. The day of the week will blink. Enter it using UP or DOWN, then press MODE to confirm and exit.

Important points: Ensure that your station is powered correctly during these operations. If you change the time settings, the seconds will automatically reset to zero. All settings will be saved and remain active even after a brief battery cut if you install new batteries correctly. If needed, you can completely reset the device by pressing the RESET button located inside the battery compartment.

Question 5

What should I do if my OREGON SCIENTIFIC BAR122HGN weather station does not start after changing the batteries?

Accepted Answer

After changing the batteries in your OREGON SCIENTIFIC BAR122HGN weather station, it is important to check several elements to ensure the system functions properly. Here are the steps to follow:

1. Check the types and quality of the batteries

Make sure you have inserted the right new high-quality batteries:

Main unit: 4 batteries of type LR06 or AA
Remote sensor: 2 batteries of type LR03 or AAA

Used or low-quality batteries will not provide enough power. If you are using low voltage or partially drained batteries, replace them with new alkaline batteries from a reliable brand.

2. Check the polarity and positioning of the batteries

When inserting the batteries, strictly follow the polarity indicated inside the compartment (+ and -). Reversing the polarity will completely prevent the device from functioning. Also, ensure that the batteries are properly seated and in place.

3. Clean the battery contacts

Before reinstalling the batteries, gently clean the metal contacts in the compartment with a dry cloth or cotton swab to remove any signs of oxidation or corrosion. Dirty or oxidized contacts prevent good electrical contact.

4. Bring the sensor closer to the main unit and perform a reset

To ensure better synchronization between the transmission and reception of signals, place the remote sensor as close as possible to the main unit, then press the RESET button with a pointed object. Allow the main device to automatically search for the sensor signals for about 3 minutes. If the reception is successful, the temperature and humidity readings will be displayed.

5. Force a signal search if necessary

If after 3 minutes the main device still only displays dashes (---), manually force a search: press and hold the [CHANNEL] and [MEMORY] buttons simultaneously for 2 seconds. This will initiate a new 3-minute search. This procedure is very useful for synchronizing transmission and reception.

6. Check the LED indicator of the sensor and eliminate interference

Observe the LED indicator of the remote sensor: it should blink within a minute after installing the batteries. If it does not blink, replace the batteries in the sensor. Also, keep the main unit away from all sources of electromagnetic interference, including DECT phones, mobile phones, microwave ovens, and Wi-Fi routers. These devices can temporarily block radio signals at 433 MHz.

Important note on cold temperatures: When the outside temperature drops below zero, the batteries in the outdoor sensors freeze and their voltage drops, reducing their performance and communication range (about 100 meters under normal conditions).

If after following all these steps the device still does not start, there may be a hardware defect. In this case, contact Oregon Scientific customer service or the retailer for repair or replacement.

User manual OREGON SCIENTIFIC Weather Station : user manuals and guides in PDF

Models OREGON SCIENTIFIC Weather Station most viewed

Other categories OREGON SCIENTIFIC

Recent questions about Weather Station OREGON SCIENTIFIC