Question 1

Where to buy a replacement blade for the Güde GRKS 1400 trimmer?

Accepted Answer

To replace the blade of your Güde GRKS 1400 trimmer, you have several options:

Specialized retailers

Kamody.fr - Specialist in Güde spare parts, offers blades compatible with the GRKS 1400
Cdiscount - Spare parts and rotary blades for the GRKS 1400
Amazon.fr - Replacement blades and accessories for Güde mowers and trimmers
eBay.fr - Secondary market with used or new spare parts

Important advice: Before replacing the blade, make sure to completely unplug the device and wait for the blade to come to a complete stop. Check that the replacement blade is well balanced once installed to avoid excessive vibrations.

Question 2

How to properly adjust the Bowden cable of the Güde Eco Wheeler 412.2 P lawn mower?

Accepted Answer

The Bowden cable of your Güde Eco Wheeler 412.2 P lawn mower connects the control handle (Start-Stop) to the recoil starter and the priming pump lever. A correct adjustment is essential for starting the engine effortlessly and ensuring reliable operation.

Location of the Bowden cable: On this model, the Bowden cables are located along the handlebars and pass under the engine cover. One controls the Start-Stop lever (on/off), the other operates the priming pump. Look for the hollow nut (junction nut) that holds the cable to the control box near the carburetor or the starting system.

Checking and tension: Gently pull on the Start-Stop handle and observe if the reaction is immediate and without resistance. If the cable feels loose (excess play), the engine may not start properly. If the handle is difficult to operate, the cable is likely too tight. The cable should slide freely without any sticking points.

Adjustment with the hollow nut: Locate the hollow nut that holds the cable. By slightly turning this nut clockwise, you tighten the cable; counterclockwise, you loosen it. Before adjusting, clean the cable with a cloth. Make small adjustments of a quarter turn at a time, then test the handle after each adjustment to achieve optimal tension: little play, but without forcing the Start-Stop lever.

Finishing and maintenance: Once the tension is correctly adjusted, ensure that the hollow nut is securely tightened to prevent slipping. Apply a light lubrication with a Teflon spray on the cable to facilitate its sliding and prevent corrosion. Regularly test the operation of the priming pump (6 presses when the engine is cold, 3 when it is hot): the cable should return to its initial position quickly and smoothly.

If after adjustment the engine remains difficult to start, check the condition of the cable itself (corrosion, fraying) and consult the "Troubleshooting" section of the manual. A good adjustment of the Bowden cable is crucial for ensuring the reliable starting of your Güde Eco Wheeler 412.2 P lawn mower.

Question 3

How to remove the spark plug cover on the Güde BIG WHEELER 554.1 R LIES lawn mower?

Accepted Answer

To remove the spark plug cover on your Güde BIG WHEELER 554.1 R LIES lawn mower, follow these simple steps:

1. Ensure safety

Before any handling, make sure the mower is turned off and the ignition key is removed. Allow the engine to cool down if the machine has been used recently to avoid any risk of burns.

2. Locate the spark plug cover

The cover is usually located above the spark plug, often in the form of a plastic or metal cap.

3. Identify the fasteners

Check if the cover is held by screws, clips, or fasteners. Depending on the type of fastener, you will need a suitable screwdriver or pliers.

4. Remove the cover

Gently unscrew or unclip the fasteners without forcing to avoid damaging the parts.
Then carefully remove the cover to access the spark plug.

5. Access the spark plug

Once the cover is removed, you can check, clean, or replace the spark plug as needed.

By following these steps, you will be able to easily access the spark plug of your Güde BIG WHEELER 554.1 R LIES lawn mower safely.

Question 4

How to change the spark plug of the Güde BIG WHEELER 554.1 R LIES mower?

Accepted Answer

To change the spark plug of your Güde BIG WHEELER 554.1 R LIES mower, first ensure that the mower is turned off. Remove the anti-interference (cable) from the spark plug by pulling on the protective cap, then wait for all moving parts to come to a complete stop and for the engine to cool down sufficiently before starting your work.

Locate the spark plug, usually visible on top of the engine block. Carefully disconnect the spark plug cable by pulling it directly, being careful not to pull on the wire itself. Use the spark plug wrench (suitable wrench from 16 to 20 mm depending on the spark plug) to unscrew the used spark plug by turning counterclockwise. Completely remove the old spark plug.

Before installing the new spark plug, check that the electrode gap is properly set to 0.6 to 0.8 mm, in accordance with the specification of the 4-stroke engine. Use a gap gauge to check this distance. Gently screw in the new spark plug by hand to avoid cross-threading, then tighten it securely using the spark plug wrench, without over-tightening to avoid damaging the seal.

Reconnect the spark plug cable, ensuring it is pushed all the way onto the spark plug cap. The connection should be tight and secure. Then restart the mower to check that the engine runs properly with the new spark plug. If you experience difficulties starting or engine misfires, check the electrode gap again.

According to the manufacturer's maintenance schedule, replace the spark plug every 24 months or after 250 hours of operation, whichever comes first. Using original Güde replacement parts is highly recommended to ensure compatibility and durability.

User manual Güde Lawn mower : user manuals and guides in PDF

Models Güde Lawn mower most viewed

Other categories Güde

Recent questions about Lawn mower Güde