PWSAP 20-Li A1 - Grinder PARKSIDE - Free user manual and instructions

Brand	Parkside
Model	PWSAP 20-Li A1
Product Type	Angle Grinder
Power Source	20 V Li-Ion battery
Disc Diameter	125 mm (5 in)
No-Load Speed	8500 RPM
Dimensions (L x W x H)	300 x 120 x 100 mm
Weight (without battery)	1.5 kg
Battery Compatibility	Parkside 20 V series
Overload Protection	Yes
Restart Protection	Yes
Soft Start	No
Safety Switch	Yes, lock-off button
Protection Guard	Adjustable
Spindle Lock	Yes
Ergonomic Handle	Yes, with soft grip
Vibration Control	Yes
Cleaning	Wipe with dry cloth, keep vents clean
Carbon Brush Replacement	Required periodically
Spare Parts Available	Discs, brushes, battery, charger, guard
Repairability	Modular design, replaceable components

Frequently Asked Questions - PWSAP 20-Li A1 PARKSIDE

How do I change the grinding disc?

Press the spindle lock button, then use the wrench to loosen the flange nut. Replace the disc and tighten the nut firmly.

What battery does this grinder use?

It uses a 20 V Parkside Li-Ion battery from the PWP series. Ensure the battery is fully charged before use.

Is the grinder suitable for cutting metal?

Yes, with an appropriate cutting disc (max 125 mm diameter). Always use the guard and wear protective gear.

How do I clean the grinder?

Disconnect the battery. Wipe the housing with a dry cloth. Clean air vents with compressed air. Do not use water.

What is the no-load speed?

The no-load speed is 8500 RPM. This may vary slightly depending on the battery charge level.

Does it have a safety trigger?

Yes, it has a lock-off switch that prevents accidental start-up. Press the safety button first, then squeeze the trigger.

Can I use grinding wheels with a 22.23 mm bore?

Yes, the spindle has a standard M14 thread and accepts discs with a 22.23 mm bore.

How do I replace the carbon brushes?

Remove the brush caps on the motor housing. Take out worn brushes and insert new ones. Ensure they are identical to the original.

Why does the grinder stop during use?

This may be due to overload protection or a low battery. Allow the tool to cool down and use a fully charged battery.

Where can I find spare parts?

Spare parts are available from Parkside service centers or online retailers. Common parts include discs, brushes, and the battery.

USER MANUAL PWSAP 20-Li A1 PARKSIDE

CORDLESS ANGLE GRINDER 20 V PWSAP 20-Li A1

OWIM GmbH & Co. KG

Sahargate

267/167 Necosulin

GERMANY

Model No: HG02735

Vencor 01/2017

GJ CY

CORDLESS ANGLE GRINDER 20 V

Operation and Safety Notes

Translator of the original expression

1、公司基本情况

(14)

АКУМУЛАТОРЕНЪГЛОШЛАЙФ 20 V

Original belief in meaning

GB/CY Operation and Safety Notes Pages 5

HP: Insub to and cloumout. Stavlon 20

HK Spale zu den / sigui 02 Srlu 153 20

BG Указания за употреба и веасопасност стр. 25

Table of contents

List of pictograms used....Page 6

Introduction Page 6

Intended use Page 6

Parts description......Page 6

Scope of delivery....Page 6

Technical data...... Page 7

Safety warnings Page 7

General power tool safety warnings...... Page 7

Angle grinder warnings Page 9

Vibration and noise reduction Page 12

Behaviour in emergency situations......Page 12

Residual risks......Page 12

Battery charger safety warnings Page 12

Initial use......Page 13

Unpacking Page 13

Accessories Page 13

Before use Page 13

Attaching / removing the battery pack......Page 13

Charging the battery pack...... Page 14

Checking the battery level Page 14

Attaching / removing the auxiliary handle Page 14

Adjusting the guard......Page 14

Attaching / removing the accessory......Page 15

Operation Page 16

Switching on and off Page 16

Trial run Page 16

Grinding......Page 16

Wire brushing Page 16

After use......Page 16

Cleaning and care Page 16

Cleaning Page 16

Maintenance......Page 17

Repair Page 17

Storage Page 17

Transportation Page 17

Troubleshooting Page 17

Disposal Page 18

Service Page 18

Warranty Page 18

Translation of original declaration of conformity...... Page 19

List of pictograms used:
	Read the instruction manual. Protect the battery pack and moisture.		ck against water and moisture.
			Protect the battery pack from fire.
	Use in dry indoor rooms only.		Alternating current
	Switch the appliance off and remove the battery pack before replacing attachments, cleaning and when not in use.		Direct current
		T3.15A	Fuse
	Protection class II (Double insulation)	Wear ear protection!
	Protect the battery pack against heat and continuous intense sunlight.		Wear ear protection!

Cordless Angle Grinder 20 V PWSAP 20-Li A1

● Introduction

We congratulate you on the purchase of your new product. You have chosen a high quality product. The instructions for use are part of the product. They contain important information concerning safety, use and disposal. Before using the product, please familiarise yourself with all of the safety information and instructions for use. Only use the product as described and for the specified applications. If you pass the product on to anyone else, please ensure that you also pass on all the documentation with it.

- Intended use

This cordless angle grinder 20 V (hereinafter "product" or "power tool") is designed for grinding and wire brushing.

The product is not intended for any other types of applications (e.g. grinding with unsuitable grinding tools, grinding with a coolant solution, grinding or cutting hazardous materials such as asbestos). The product is to be used by adults. Children under the age of 16 may not use the tool except under supervision.

Any other use or modification of the product are considered improper use and can result in hazards such as death, life-threatening injuries and damage. The manufacturer is not liable for any damages caused by improper use. The product is not intended for commercial use or for any other application.

- Parts description

Figure A:

1 Battery level button
2 Release button
3 Battery level indication light
4 Battery pack
5 Chuck key
6 Auxiliary handle with chuck key storage
7 Guard
8 Locking flange
9 Backing flange
10 Spindle lock button
11 Threads for auxiliary handle
12 On / off switch
13 Charger
14 Charging status LED - Red
15 Charging status LED - Green

- Scope of delivery

1 Cordless angle grinder 20 V PWSAP 20-Li A1
1 Battery pack PWSAP 20-Li A1-1
1 Rapid battery charger PWSAP 20-Li A1-2
1 Auxiliary handle
1 Guard
1 Chuck key stored in auxiliary handle
1 Instruction manual

● Technical data

Cordless angle grinder: PWSAP 20-Li A1

Rated voltage: 20 V ---

Rated speed n: 10000 min -1

Rated capacity: ∅ 125 mm

Disc thickness: max. 6 mm

Spindle thread: M14

Weight (incl.

accessories): 2.66 kg

Battery pack: PWSAP 20-Li A1-1

Type: Lithium ion

Rated voltage: 20 V — max.

Capacity: 5 Ah

Number of cells: 10

Rapid battery charger: PWSAP 20-Li A1-2

INPUT:

Rated voltage and 100 - 240 V\~,

frequency: 50 - 60 Hz

Power consumption: 95 W

OUTPUT:

Rated voltage: 14.4 - 20 V ---

Charging current: 4 A

Charging time: approx. 90 min

Protection class: II / ☐

Noise emission value:

Noise measurement value determined in accordance with EN 60745. The A-rated noise level of the product is typically as follows:

Sound pressure level L_pA : 68.7 dB(A)

Uncertainty K_pA : 3 dB

Sound power level L_WA : 79.7 dB(A)

Uncertainty K_WA : 3 dB

Vibration values:

Total vibration values (vector total of three directions) determined in accordance with EN 60745:

(main handle)

Hand/arm

vibration a_h,AG : 4.37 m/s ²

(auxiliary handle)

Hand/arm

vibration a_h,AG : 5.23 m/s ²

Uncertainty K: 1.5 m/s²

The values apply for the work mode surface grinding. Other applications may have different vibration emission values

WARNING!

Wear ear protection!

WARNING!

The vibration level varies in accordance with the use of the power tool and may be higher than the value specified in these instructions in some cases. There is a risk of underestimation of the vibration load if the power tool is used regularly in this manner. Try to keep the vibration loads as low as possible. Measures to reduce the vibration load are, e.g. wearing gloves and limiting the working time. Wherein all states of operation must be included (e.g. times when the power tool is switched off and times where the power tool is switched on but running without load).

NOTE

The vibration level specified in these instructions has been measured in accordance with a standardised measuring procedure specified in EN 60745 and can be used to make equipment comparisons. The specified vibration emission value can also be used to make an initial exposure estimate.

Safety warnings

● General power tool safety warnings

WARNING!

Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

1. Keep work area clean and well lit.
   Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while operating a power tool.
   Distractions can cause you to lose control.

Electrical safety

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
2. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
5. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
6. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

1. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

4. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

5. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

6. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

Power tool use and care

1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

4. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
5. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool's operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

Battery tool use and care

1. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
2. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
3. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
4. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

Service

1. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

● Angle grinder warnings

Safety warnings common for grinding and wire brushing operations:

1. This power tool is intended to function as a grinder and wire brush. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
2. Operations such as sanding, polishing or cutting-off are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
3. Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
4. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
5. The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.

6. Threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour size hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.

7. Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.

8. Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
9. Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
10. Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the power tool "live" and could give the operator an electric shock.

11. Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.

12. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.

13. Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.
14. Do not operate the power tool near flammable materials. Sparks could ignite these materials.
15. Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.

Further safety instructions for all operations - Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel's movement at the point of pinching. Abrasive wheels may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

• Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
  ■ Never place your hand near the rotating accessory. Accessory may kickback over your hand.

Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel's movement at the point of snagging.
Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback.
Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control.

Additional safety instructions for grinding - Safety warnings specific for grinding

1. Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.
2. The grinding surface of centre depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.
3. The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with wheel and sparks that could ignite clothing.
4. Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.
5. Always use undamaged wheel flanges that are of correct size and shape for your selected wheel.

Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

1. Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst.

Additional safety instructions for wire brushing operations - Safety warnings specific for wire brushing operations:

1. Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin.

2. If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces.

Additional angle grinder warnings

• Only use grinding discs where the indicated rotational speed is at least as high as what has been specified on the name plate of the product.
• Carry out a visual inspection of the grinding disc before use. Do not use any damaged or deformed discs. Replace any damaged or worn discs.
  ■ Make sure that the sparks produced by grinding do not present a danger, e.g. reach people or ignite flammable substances.
  ■ Always wear safety goggles, safety gloves, respiratory protection and ear protection when grinding.
  ■ Never keep the fingers between the disc and spark protection or in close proximity to the protective hoods. There is a risk of crushing.
  The rotating parts of the product cannot be covered due to functional reasons. Therefore, proceed cautiously and hold the workpiece firmly in order to avoid slipping which could cause your hands to come into contact with the disc.
  The workpiece gets hot during grinding. Do not touch the machined area, allow it to cool down. There is a risk of burning. Do not use coolants or the like.
• Do not work with the product, if you are tired or have consumed alcohol or tablets. Always have a break on time.
  ■ Turn off the product and, before doing any servicing, remove the battery pack.

● Vibration and noise reduction

To reduce the impact of noise and vibration emission, limit the time of operation, use low-vibration and low-noise operating modes as well as wear personal protective equipment. Take the following points into account to minimise the vibration and noise exposure risks:

■ Only use the product as intended by its design and these instructions.
■ Ensure that the product is in good condition and well maintained.
- Use correct cutting attachments for the product and ensure they are in good condition.
- Keep tight grip on the handles/grip surface.
- Maintain this product in accordance with these instructions and keep it well lubricated (where appropriate).
Plan your work schedule to spread any high vibration tool use across a longer period of time.

● Behaviour in emergency situations

Familiarise yourself with the use of this product by means of this instruction manual. Memorise the safety warnings and follow them to the letter. This will help to prevent risks and hazards.

■ Always be alert when using this product, so that you can recognise and handle risks early. Fast intervention can prevent serious injury and damage to property.
- Switch the product off and remove the battery pack if there are malfunctions. Have the product checked by a qualified professional and repaired, if necessary, before you operate it again.

- Residual risks

Even if you are operating this product in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this product:

■ Health defects resulting from vibration emission if the product is being used over long periods of time or not adequately managed and properly maintained.
Injuries and damage to property due to broken cutting attachments or the sudden impact of hidden objects during use.

■ Danger of injury and property damage caused by flying objects.

WARNING!

This product produces an electromagnetic field during operation! This field may under some circumstances interfere with active or passive medical implants! To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their doctor and the medical implant manufacturer before operating this product!

● Battery charger safety warnings

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

■ Children shall not play with the appliance.
■ Cleaning and user maintenance shall not be made by children without supervision.
- Do not charge non-rechargeable batteries. Disregarding this instruction may be hazardous.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
■ Protect the electrical parts against moisture. Do not immerse such parts in water or other liquids to avoid electrical shock. Never hold the appliance under running water. Pay attention to the instructions provided for cleaning, maintenance and repair.
■ The appliance is suitable for indoor use only.
■ This appliance is only designed for charging the battery pack type: Parkside Performance 20 V battery.

CAUTION! RISK OF EXPLOSION

Never charge non-rechargeable batteries! Protect the battery against heat, e. g., against continuous intense sunlight, fire, water and moisture. Danger of explosion.

Initial use

Unpacking

WARNING!

The product and the packaging are not children's toys! Children must not play with plastic bags, sheets and small parts! There is a danger of choking and suffocation!

1. Unpack all parts and lay them on a flat, stable surface.
2. Remove all packing materials and shipping devices if applicable.
3. Make sure the delivery contents are complete and free of any damage. If you find that parts are missing or show damage do not use the product but contact your dealer. Do not use the product unless missing parts have been delivered in addition or defective parts have been replaced. Using an incomplete or damaged product represents a hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and operation. This also includes suitable personal protective equipment.

Accessories

To operate this product safely and correctly, the following accessories, i. e. tools and attachments, are necessary:

□ Grinding disc
□ Wire brush

Accessories and tools are available through your authorised dealer. When buying always consider the technical requirements of this product (see "Technical data").

If you are not certain, ask a qualified specialist and get advice from your trusted dealer.

NOTE

This instruction manual contains information and suggestions for several attachments and their uses. The attachments mentioned are not necessarily included in the shipment, but are meant to indicate additional possibilities for using this product.

Before use

Attaching / removing the battery pack

Attaching the battery pack:

1. Align the battery pack 4 to the handle and slide it onto it. Ensure it clicks noticeably in place.

Removing the battery pack:

1. Press the release button 2 and remove the battery pack 4.

● Charging the battery pack

NOTE

The battery pack comes partly charged. Charge the battery pack 4 prior to first use, ideally at least 90 minutes.
Always pull out the plug of the charger from the mains before removing or connecting the battery pack 4 to the charger.
▶ Never charge the battery pack when the ambient temperature is below 10 °C or above 40 °C.
Rest the charge for at least 15 minutes between successive charging sessions.
If no battery pack is inserted into the charger 13 and the charger is connected to mains, the charging status LED 15 lights up green.

1. Connect the battery pack 4 to the battery charger 13.
2. Insert the mains plug into the socket. The charging status LED 14 lights up red. Once the battery pack 4 is completely charged, the green charging status LED 15 indicates that the charging process is complete.
3. Disconnect the charger 13 from the mains and remove the battery pack 4 from the charger.
4. Attach the battery pack 4 back to the product.

Charging status LEDs

Green LED lights up without battery pack	Charger ready
Green LED lights up with battery pack	Battery pack fully charged
Red LED lights up with battery pack	Battery pack charging
Red LED flashes with battery pack	Battery pack defect
Green LED flashes with battery pack	Battery pack too cold or warm

- Checking the battery level

☐ Press the battery level button 1 to check the charging level of the battery pack 4. The charging level will be shown on the battery level indication light 3.

3 Red LEDs light up maximum charging level

2 Red LEDs light up medium charging level

1 Red LEDs lights up low charging level

☐ Charge the battery pack4 before operation when it is at medium or low charging level.

● Attaching / removing the auxiliary handle

NOTE

The product must only be operated with the auxiliary handle mounted.

1. Screw the auxiliary handle 6, depending on the type of work, to the left, right or top of the product using the threads for the auxiliary handle 11.

- Adjusting the guard

WARNING!

▶ Always remove the battery pack from the product before adjusting the guard in order to avoid switching it on accidentally.

CAUTION! RISK OF INJURY!

▶ Wear protective gloves. Be careful when gripping and turning the guard due to potential finger squeezing hazard between the guard and disc.

NOTE

The product must only be operated with the guard mounted.

1. Adjust the guard 7 such that any sparks or detached parts cannot hit either the user or any bystanders.
2. The guard 7 must also be positioned such that the sparks cannot ignite combustible parts, including those in the surroundings.
3. Turn the guard 7 to the required position so the clamp should match the notches on the guard 7.

- Attaching / removing the accessory

WARNING!

▶ Always remove the battery pack from the product before changing the accessory in order to avoid switching it on accidentally.
Always use the correct accessories according to the intended use! Observe the technical requirements of this product (see section Technical data) when purchasing and using accessories!
Accessories can be sharp and become hot during use! Handle them carefully! Wear safety gloves when handling accessories in order to avoid injuries like burns and cuts!
▶ Never press the spindle lock whilst the spindle is rotating!
The arrow on the accessory must correspond to the arrow showing the direction of rotation (running direction shown on the product).
▶ Ensure that the accessory is suitable for the rotational speed of the product.
Do not use any saw blades.

CAUTION! RISK OF INJURY!

▶ Only use accessory recommended by the manufacturer. Using other attachment tools and other accessories can represent a risk of injury for you.
▶ Only use accessory, which bear information about the manufacturer, type of binding, dimension and permitted number of revolutions.
▶ Only use grinding discs where the printed rotational speed is at least as high as what has been specified on the product marking.
Do not use any broken, cracked, or otherwise damaged accessories.
Only use flawless grinding discs (ringing test: when you strike the disc with a plastic hammer, it results in a clear sound).
▶ Ensure that the accessory dimensions match those of the product.
▶ Never re-drill a locating hole which is too small to make it larger.
▶ Never use separate bushings or adapters in order to make discs with a hole that is too large fit the product.
▶ Never operate the product without protective equipment.
▶ Support plates or workpieces to reduce the risk of kickback from a jammed disc. Large workpieces may bend under their own weight. The workpiece must be supported on both sides of the disc, near the disc as well as at the edge.
▶ Always reassemble the product completely after replacing accessories.

1. Press and hold the spindle lock button 10.
2. Release the locking flange 8, with the chuck key 5.
3. Mount the desired accessory onto the backing flange 9 . Label should always face the product.
4. Mount the locking flange 8 on the spindle.
5. Press and hold the spindle lock button 10 and tighten the locking flange 8 tight again using the chuck key 5.

Operation

CAUTION! RISK OF INJURY!

Keep your hands away from the accessory when the product is in operation.

Switching on and off

This power tool is to be switched on in two steps.

Switching on:

1. Push the rear part of the on / off switch 12 down and slide it forward. For continuous activation, now tilt the front part downwards until it engages.

Switching off:

1. Press the rear part of the on / off switch 12 so that it snaps back into its off-position to switch the product off.

Trial run

NOTE

Always carry out a trial run before carrying out your first grinding procedure and after every accessory replacement. Switch the product off immediately if the accessory is not rotating smoothly, if considerable vibration occurs or if you hear abnormal noises.

Grinding

WARNING!

▶ Never use a cutting disc for grinding!

1. Hold the product at a 10° to 15° angle for easy handling and smooth grinding results.
2. Apply the grinding disc to the work surface with a light, steady pressure for maximum grinding efficiency. It should never be necessary to force the product. The weight of the product applies adequate pressure.
3. Excessive pressure will overload the motor, slow the grinding action, put dangerous stress on the grinding disc and causes breakage.
4. Move the product back and forth steadily.

● Wire brushing

WARNING!

Do not use brush that is damaged, or which is out of balance. Use of damaged brush could increase potential for injury from contact with broken brush wires.

1. Avoid applying too much pressure which causes over bending of wires, leading to premature breakage.
2. Work with moderate feed, suited to the material being worked.
3. Avoid bouncing and snagging the wire brush, especially when working corners, sharp edges etc. This can cause loss of control and kick-back.

After use

1. Switch the product off, remove the battery pack 4 and let it cool down.
2. Check, clean and store the product as described below.

● Cleaning and care

WARNING!

Always switch the product off, remove the battery pack and let the product cool down before performing inspection, maintenance and cleaning work!

- Cleaning

☐ The product must always be kept clean, dry and free from oil or grease. Remove debris from it after each use and before storage.
☐ Regular and proper cleaning will help ensure safe use and prolong the life of the product.
☐ Inspect the product before each use for worn and damaged parts. Do not operate it if you find broken and worn parts.
□ Never allow fluids to get into the product.
□ Clean the product with a dry cloth. Use a brush for areas that are hard to reach.
☐ In particular clean the air vents after every use with a cloth and brush.
☐ Remove stubborn dirt with high pressure air (max. 3 bar).

NOTE

Do not use chemical, alkaline, abrasive or other aggressive detergents or disinfectants to clean this product as they might be harmful to its surfaces.

● Maintenance

Before and after each use, check the product and accessories (or attachments) for wear and damage. If required, exchange them for new ones as described in this instruction manual. Observe the technical requirements (see "Technical data").

Repair

This product does not contain any parts that can be repaired by the user. Contact an authorised service centre or a similarly qualified person to have it checked and repaired.

Storage

☐ Switch the product off and remove the battery pack 4.
□ Clean the product as described above.
☐ Store the product and its accessories in a dark, dry, frost-free, well-ventilated place.
□ Always store the product in a place that is inaccessible to children. The ideal storage temperature is between 10 °C and 30 °C.
☐ We recommend using the original package for storage or covering the product with a suitable cloth or enclosure to protect it against dust.
☐ Regularly check the charge level of the battery pack, if it is to be stored for an extended period. Optimum storage conditions are cool and dry.
☐ Grinding discs must be dry and stored upright, and should never be stacked.

- Transportation

☐ Switch the product off and remove the battery pack 4.
□ Attach transportation guards, if applicable.
□ Always carry the product by its handles.
☐ Protect the product from any heavy impact or strong vibrations which may occur during transportation in vehicles.
☐ Secure the product to prevent it from slipping or falling over.

● Troubleshooting

WARNING!

Only perform the steps described within these instructions! All further inspection, maintenance and repair work must be performed by an authorised service centre or a similarly qualified specialist if you cannot solve the problem yourself!

Suspected malfunctions are often due to causes that the users can fix themselves. Therefore check the product using this section. In most cases the problem can be solved quickly.

Problem Possible cause		Solution
Product does not start	Battery pack not properly attached	Attach properly
	Battery pack discharged	Remove and charge battery pack
	Battery pack damaged	Check by a specialist electrician
	Other electrical defect to the product	Check by a specialist electrician
Product does not reach full power	Air vents are blocked	Clean the air vents
Unsatisfactory result	Accessory is worn	Replace with a new one
	Accessory not suitable for intended operation	Use suitable accessory
Product suddenly stops	Product overloaded	Remove the product from the workpiece and switch it on again
	Battery pack discharged	Remove and charge battery pack
	Battery pack too hot	Remove battery pack and let it cool down
Excessive vibration or noise	Accessory is dull/damaged	Replace with a new one
	Bolts/nuts are loose	Tighten bolts/nuts
Guard cannot be adjusted	Debris Clean the	product and lubricate the guard base if necessary

● Disposal

The packaging is made entirely of recyclable materials, which you may dispose of at local recycling facilities. The Green Dot is not valid for Germany.

Observe the marking of the packaging materials for waste separation, which are marked with abbreviations (a) and numbers (b) with following meaning: 1 - 7: plastics / 20 - 22: paper and fibreboard / 80 - 98: composite materials

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

Contact your local refuse disposal authority for more details of how to dispose of your worn-out product.

To help protect the environment, please dispose of the product properly when it has reached the end of its useful life and not in the household waste. Information on collection points and their opening hours can be obtained from your local authority.

Faulty or used batteries / rechargeable batteries must be recycled in accordance with Directive 2006/66/EC and its amendments. Please return the batteries / rechargeable batteries and / or the product to the available collection points.

Environmental damage through incorrect disposal of the batteries / rechargeable batteries!

Remove the batteries / battery pack from the product before disposal. Batteries / rechargeable batteries may not be disposed of with the usual domestic waste. They may contain toxic heavy metals and are subject to hazardous waste treatment rules and regulations. The chemical symbols for heavy metals are as follows: Cd = cadmium, Hg = mercury, Pb = lead. That is why you should dispose of used batteries / rechargeable batteries at a local collection point.

● Service

WARNING!

▶ Have your product repaired at the service centre or an electrician, using only original manufacturer parts. This will maintain the safety of this product.
▶ Always have a plug or power cord replaced by the product manufacturer or its service centre. This will maintain the safety of this product.

● Warranty

The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of product defects you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below. The warranty for this product is 5 years from the date of purchase. Should this product show any fault in materials or manufacture within 5 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you. The warranty period begins on the date of purchase. Please keep the original sales receipt in a safe location. This document is required as your proof of purchase. This warranty becomes void if the product has been damaged, or used or maintained improperly.

The warranty applies to defects in material or manufacture. This warranty does not cover product parts subject to normal wear, thus possibly considered consumables (e.g. batteries) or for damage to fragile parts, e.g. switches, rechargeable batteries or glass parts.

The warranty for this rechargeable battery pack is 1 year from the date of purchase.

Warranty claim procedure

To ensure quick processing of your case, please observe the following instructions:

Please have the till receipt and the item number (e.g. IAN 123456) available as proof of purchase. You will find the item number on the type plate, an engraving on the front page of the instructions (bottom left), or as a sticker on the rear or bottom of the product.

If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.

You can return a defective product to us free of charge to the service address that will be provided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.

GB

Service Great Britain

Tel.: [phone]

(£ 0.10/Min.)

E-Mail: [e-mail]

CY

Service Cyprus

Tel.: [phone]

E-Mail: [e-mail]

IAN 289752

● Translation of original declaration of conformity

We, OWIM GmbH & Co. KG, Stiftsbergstraße 1, DE-74167 Neckarsulm, GERMANY, hereby declare under our sole responsibility that the product: cordless angle grinder 20 V PWSAP 20-Li A1, Model No.: HG02735, Version: 08 / 2017, to which this declaration refers, complies with the standards / normative documents of 2006/42/EC, 2014/35/EU, 2014/30/EU, 2011/65/EU.

Applied harmonised standards:

EN 60745-1:2009/A11:2010

EN 60745-2-3:2011/A13:2015

EN 60335-1:2012/A11:2014

EN 62233:2008

EN 60335-2-29:2004/A2:2010

EN 55014-1:2006/A2:2011

EN 55014-2:2015

EN 61000-3-2:2014

EN 61000-3-3:2013

EN 50581:2012

Serial number: IAN 289752

Tobias König

Division Manager / Responsible for documentation

The declaration of conformity can also be viewed at: www.owim.com.

The object of the declaration described above satisfies the provisions of Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on limiting the use of certain harmful substances in electrical and electronic appliances.

Sadržaj

Popis korištenih piktograma....Stranica 21

Uvod ...... Stranica 21

Namjena....Stranica 21

Nazivni napon: 20 V ---

Nazivni napon: 20 V --- max.

Kapacitet: 5 Ah

Broj ćelija: 10

Brzi punjač za baterije:

ULAZ:

Nazivni napon i 100 - 240 V\~,