SP10 - Sewing machine TOYOTA - Free user manual and instructions

USER MANUAL SP10 TOYOTA

= TOYOTA SP10 Series

HOME-USE SEWING MACHINE

INSTRUCTION MANUAL + Read this manual carefully before use and always follow the instructions. + Keep the manual in a convenient place for easy reference. + If you give the sewing machine to someone else, also give them this instruction manual.

+ Partnames +_ How to use handwheel + _ How to use presser foot lever + How to use reverse sewing leve + How to remove extension tabl + _ How to use quick adviser. X_Sewing preparations Sewing = — — — — — — preparations + Connecting the power. +_ Installation of battery for winding the lower thread + Winding the lower thread. Threading the lower thread- Threading the upper thread Pulling up the lower thread - Application of each stitch patter! Changing the presser foot Changing the needle Relationship between the needle, thread and fabric, and adjusting the thread tension X Sewing Sewing +. Straight stitching and reverse sewing - Zigzag sewing Adjusting thread tension Buttonhole sewing - + Overcastin €) + _Zipper insertion + Blind hem stitching- 3% Maintenance Maintenance + _ Feed dog and hook maintenance : + Changing light bulb…… + Troubleshooting-… + _ Servicing double- sulated products (23ov- 240V Others > Others +_ Safety precaution about the battery- Recycling --…

X Beïore use Be sure to read this section before use + Important safety instructions ? CVCOCCOCTTTOCTTTTTCTCTTTTTTT These safety instructions are designed to prevent danger or damage arising from the incorrect operation of the machine. Read carefully and always follow the instructions. Explanation of “/\ Warning” A\Warning An incorrect operation could result in death or serious injury. A An incorrect operation could result in an injury or damage to the Â\ Caution machine. Symbol explanati RQ) Do not touch. W Prohibited actions . . p Remove the power plug O Required actions from the outlet. Use an AC 220 to 240 V power source. à 2 Not doing so could cause an electric shock or a fire. eË5) Do not damage the power cord, W modify it, bend it excessively, me jerk it or twist it. NID Doing so could cause an electric shock or a fire. If the power cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. Do not use outdoors. Doing so could cause an electric shock or a fire. Do not operate where aerosol ( spray ) products are being used or where oxygen is being administered. Doing so could cause a fire. A\ Caution When the machine is not in use it should be stored safely, not on the floor as protruding parts could cause injury if a person fell on the machine. Not doing so could cause an injury.

A\Caution Remove the power plug from the outlet when replacing the needle, presser foot, setting the upper or lower thread. Not doing so could cause an injury. Do not look away from the needle while operating the sewing machine. If the needle breaks it could cause an injury. Do not touch moving parts such as the needle, take-up lever or handwheel. Doing so could cause an injury. Children should only use the machine under the supervision of a parent or guardian. f{? Otherwise they could injure themselves. Si Do not use when young children are near the machine. EN They could touch the needle and be injured. RE? When leaving the sewing machine after use, remove the power plug from the outlet. Not doing so could cause an injury. Before using the sewing machine make sure that the presser foot holder clamp screw, needle clamp screw and needle plate screw are firmly tightened, and that the presser foot is properly set in the presser foot holder. Not doing so could cause an injury. Sewing without lowering the presser foot. Sewing while the needle is incorrectly installed Using a bent needie. Sewing while jerking the fabric. Moving the pattern selection dial while sewing. Do not performthe * following actions. : Doing so could cause . an injury. . Do not operate on an unstable surface such as a sofa or a bed. If the sewing machine falls down, it could cause an injury or damages to the machine. Do not drop or insert any foreign objects into any openings such as opening space when you remove the face cover and / or the outer casing space of bobbin case. Doing so could cause an injury or damages to the machine. Do not repair, disassemble or modify except what is mentioned in the instruction manual. Doing so could cause an electric shock, a fire or an injury. ) QID|QIOI e1R1DIe1S1S

UK ONLY IMPORTANT PLEASE READ CAREFULLY

+ How to change the power plug ?

RAR LRLRLRLRLRLLRLLLLLLLLLLLÈLLELS SA

A\Warning When you change the power plug or cord, do not repair, disassemble or modify except at the authorised dealer or service centre. Doing so could cause an electric shock or a fire If for any reason the power plug for this product is removed 1 it should be immediately disposed of safety and not stored anywhere where it could be inadvertently used again. Doing so could cause an electric shock or a fire The wires in this mains lead are coloured in accordance with the following code: BLUE-NEUTRAL BROWN-LIVE (OR ACTIVE ) As the colours of the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug - PROCEED AS FOLLOWS: The earth plug pin is unnecessary. As the machine is designed under double insulation structure, the earth wire is removed from the machine. The wire coloured BROWN must be connected to the terminal marked L or À or coloured RED. The wire coloured BLUE must be connected to the terminal marked N or coloured BLACK. Neither core is to be connected to the earth terminal of a three-pin plug.

> Betore use + Part names ‘ ÉOLRLALLLLLLLL A + External appearance may differ from model to model. Upper thread tension dial Spool pin Thread guid read guide Quick adviser Take-up lever \ Pattern selection dial Light bulb Face cover Reverse sewing lever Extension table (Accessory Box) Needle clamp screw Needle thread guide Presser foot holder Needle plate Presser foot holder clamp screw Feed dog Presser foot Bobbin case cover Bobbin case

Thread winding spindle Thread winding switch Hollow for carrying Insert your hand to the hollow ) when carrying sewing machine Presser foot lever Handwheel Thread cutter Buttonhole adjustment screw Battery holder Foot controller

RE | —— H — eee > Betore use + How to use handwheel RRARLALLLLRLLLLLLLLLLLA Handwheel Always turn the handwheel towards yourself. (in the direction of the arrow, forwards) Note: If you turnit in the reverse direction it could tangle the thread.

+ How to use presser foot lever ; VIT TCTTTTTTTTTTTTTTTTTTTIT ER ———— + When sewing, lower the presser foot lever to lower the presser foot. (Position @O) + When inserting fabric, lift up the presser foot lever to raise the presser foot. (Position @) + Wheninserting very thick fabric under the presser foot, the lift height can be increased by holding the presser foot lever at this position. (Position ©) : le + How to use reverse sewing lever ; VITITCTTCTTTTTTTTTTTTTTTTTTTT + While lowering the reverse sewing lever, reverse sewing is performed. + Remove your finger from the reverse sewing lever to return to forward direction sewing. + How to remove extension table £

RAR LLLLLLLLLLLLLLLLLLLLLL SA

Pull out the extension table (accessory box) in the direction of the arrow.

+ How to use quick adviser oovvooocoooooooerss + Jammed stitches + Unbalanced stitches + The fabric wrinkles/puckers + Missed stitches Above troubles happen, refer to illustration @ for countermeasures. When you want to know how to attach presser foot, refer to illustration © for countermeasures. This quick adviser describes basic countermeasures about the main troubles. Describes below 3 operations. © Adiusting thread tension. @ Threading the lower thread @ correctly.

Threading the upper thread correctly. Describes how to attach presser foot. O Paise the presser foot lever. @ Set the presser foot under the presser foot holder correctly. 6 Lower the presser foot lever. im...

x Sewing preparations + Connecting the power PLV TOCTTITTTCTTCTTTTTTT Prepare the foot controller. à Insert the power cord connector into the terminal box. 3 Insert the power plug into the outlet. The power is turned on. —— Terminal box |__ Connector

Step on the foot controller to operate the sewing machine. \ The more you press the foot controller, the faster the Ÿ machine runs. Release the foot controller to stop the machine. Foot controller

x Sewing preparations + Installation of battery for winding the lower thread ? COCO TTTTTCTTTTTCTTOTTTTTCTTTTTTTT A battery is supplied as one of the accessories. Before winding the lower thread, install it in the battery holder on back of sewing machine. Attention |. Pull the battery holder cover out as the arrow.

Install the battery while confirming polarity of it. Attach battery holder cover. Note: Refer to page 42, 43 when purchasing or changing batteries.

Make sure that the thread winding spindle rotates by turning the thread winding switch on by pushing in the direction of arrow. Note: Thread winding spindle rotates while pushing the switch to the left.

x Sewing preparations à ù ? + Winding the lower thread, COCO TCITTTTTTITTTTTTIT The exclusive motor driven by a battery winds the lower thread. (ACaution].. N

(attention ) » 0 QUES TOO EE ) : à Pull up th | pin. ull up the spool pin <= Spool cap

Position the felt, the thread spool and the spool cap on to the spool pin. Note: A felt was originally put on to the spool pin. L J Pull the thread from the thread spool. Support the thread on the sewing machine with one hand, using the other hand pass the thread around the thread guide as shown in the diagram. nm 4

Pass the thread end through the hole of the bobbin as shown. Thread Hole S Place the bobbin on to the Groove thread winding spindle so the 1 groove will meet the shaft 4 rojection. indi prof Thread winding Shaft projection U spindle J

Hold the thread end and push the thread winding switch to the left and start winding. After winding a little, release the thread winding switch to the right and stop winding. Note: While pushing the winding switch to the left, thread winding spindle rotates.

8 | Cut extra thread above the bobbin hole. Push the thread winding switch to the left again. Wind the thread in the amount you need. 1 To stop winding, release the thread winding switch to the right.

right wrong u Remove the bobbin from the spindle. Cut the thread. 15=__

x Sewing preparations ° Threading the lower thread VIT TCTTITTTTTITTTTTITTTTT Take off the bobbin case cover by sliding it towards yourself. Pull bobbin case cover forward and lift to remove.

Insert the bobbin into the bobbin case, so it rotates counterclockwise. Note: Inserting the bobbin in the wrong direction causes irregular thread tension. Pull the end of thread through the cut-out guide @ to guide E) of the bobbin case and pull out in direction of arrow.

Bobbin a NS J Pull back end of thread about 15cm. Put bobbin case cover projections into the race retainer grooves and push closed.

x Sewing preparations ° Threading the upper thread ? VTC TOTTITTOTITTTTTITTTTT Take-up lever Turn handwheel towards yourself to raise take-up lever. Line on handwheel should be up position.(12 o'clock) Raise presser foot lever. Note: If the presser foot lever is not raised, the thread can not be threaded correctly.

Pull up the spool pin. Position the felt and the thread spool. Note: A felt was originally put on to the spool pin. Pull the thread from thread spool. Support the thread on the sewing machine with one hand, using the other hand pass the thread around the thread guide as shown in the diagram.

Pass the thread between the thread guide plate and the upper thread tension dial. Upper thread tension dial Pass the thread along the groove of the thread guide plate, as the arrow in the diagram. Pass the thread through the take-up lever.

C8 | Pass the thread through the right side needle guide. LL Check that the thread is threaded correctly. Raise the presser foot and pull the upper thread towards yourself. The thread should pull out smoothly. Lower the presser foot and pull the upper thread towards yourself. It should be resistant and difficult to pull. Needle guide Pass the thread through the needle eye from the front. Pull back about 15 cm. nm 18

x Sewing preparations ° Pulling up the lower thread ? RRRRLRLLALLALLRLLLLLLLLLLRLSSA

Hold the end of the thread, turn the handwheel towards yourself for one full turn, and stop when the needle is at its highest position. Handwheel Note: Always turn the handwheel towards yourself (in the direction of the arrow). If you turn it in the wrong direction it could tangle the thread. Note: If the thread is tight the lower thread will not come out, so hold the thread loosely. L J 2 Pull up the upper thread and the loop of the lower thread will come out. Pull out this lower thread. K LT Upper thread | Cuier thread L J 3 Align the upper thread and lower thread, and thread through the groove of the presser foot. Pull back about 15 cm. L J

x Sewing preparations

• Application of each stitch pattern PTIT TTIOTTTTTCTTTTTTTTTOTT Don't turn the pattern selection dial while operating the sewing machine. Doing so could cause an injury. Turn the handwheel towards yourself to raise the needle in the highest position. Turn the pattern selection dial to choose the pattern. Pattern selection dial 1-2-3:4 11 [ Î (] Û Buttonhole 3 Blind hem stitch 5-6 Zigzag 12 Applique Scallop stitch Overcasting 7-8 13 © © Straight stitch 1! Sewing-seams Casile stitch l û Zipper insertion = Thin fabric straight stitch ê Decorative Stitch 1 Fagotting

x Sewing preparations + Changing the presser foot RAR RRLAALRLRLRLLLLLLELLLLA ce (ORNE Men Removad Raise the presser foot lever. Turn the handwheel towards yourself (| to raise the needle. Note: Never turn in the wrong direction. Handwheel

Presser foot lever TN L J Press the presser foot holder lever in the direction of the arrow to release the presser foot.

x Sewing preparations ° Changing the needle’ RAA ALRLLRLLRELRELRELEEÉÀ Turn the handwheel towards yourself to raise the end of the needle higher than the needle plate. Screw driver for the needle plate Hold the needle in one hand, loosen the needle clamp screw with the screw driver for the needle plate, and remove the needle. Note: Do not remove the needle clamp screw. Loosen the needle clamp screw to remove the needle. [3 | Face the flat surface of the needle to the rear and insert until it makes contact with the pin. Firmly tighten the needle clamp screw with the screw driver for the needle plate. Flat surface + GCormectneedieselection + If a faulty needle is used, not only could it impair the sewing O Good needle performance, but it could also damage the needle plate or hook, or break the needle. Incorrect stitching or thread breaking, try replacing the needle.

The entire needle is bent The point of the needle The point of the needle is crushed / worn away is bent 23m

x Sewing preparations

• Relationship between the needle, thread and fabric, and adjusting

The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric. Follow the directions in the table below.

Relationship between the needle, thread and fabric

Sewingihinfabric | Sewing normal fabric Sewing thick fabric No. 75/11 No. 90/14 No. 100/16 < Thread Polyester No. 90 Cotton No. 80 to No. 120 Silk No. 80 Polyester No. 50 to No. 60 Cotton No. 60 to No. 80 Silk No. 50 to No. 80 Polyester No. 30 to No. 50 Cotton No. 40 to No. 50 Silk No. 50 ! Fabric Normal back cloth Quipler Georgette Lawn Lace, etc. Normal front cloth Broad Soft denim Satin Pile Gingham, etc. Curtains Denim Quilting Fleece Tweed Felt, etc. Adjusting the thread tension Thread tension 1-8 +1 - +3 + Use a ball point needle for the sewing alignment of stretch fabric. + Please purchase any needles not included as accessories, after checking they are specified as home-use sewing machine needles. + Use the same kind of threads for upper/lower thread. + The bigger the needle number is , the thicker the needle is, the bigger the thread number is, the thinner the thread is.

XX Sewing ° Straight stitching and reverse sewing£ VIT TCTTOTTTTITTTTTTTTTOTTTTTTIV en Straightstith 16 Turn the handwheel towards yourself to raise the needle. Turn the pattern selection dial to choose the pattern. Zigzag sewing foot (Originally attached to the sewing machine) Position the fabric and lower the presser foot lever. Step on the foot controller to begin sewing. dé Ends RG 1: After sewing, turn handwheel towards yourself until the needle is in the highest position. Raise the presser foot and pull out the fabric to the rear.

Line up two threads and cut with the thread cutter on the presser bar. Thread cutter

Reverse sewing is performed at the beginning and the end of sewing to prevent the thread from unraveling. Reverse sewing is performed while pressing down the reverse sewing lever. - Stitch 1 cm from the edge of the fabric to prevent unraveling at the start of sewing. + Sew 3 to 4 reverse stitches at the end of sewing. Note: Remove your finger from the reverse sewing lever to return to forward direction sewing. Reverse sewing lever

DL Un —— CS TO e Sewingihikiabie + When sewing thick fabric from the edge, the presser foot may tilt and be unable to feed through the fabric. Place fabric or thick paper of the same thickness as the fabric you wish to sew under the presser foot. This will enable smooth sewing. Fabric or Sewing fabric thick paper

When sewing thin fabric, sometimes fabric puckers or is not fed correctly. At that time, sewing is easier if tissue paper is placed under the fabric. After sewing remove the paper carefully. 27m

DL Un —— CS TO + Sewingtube-<hapedfabrics +

Pull out the extension table (accessory box) in the direction of the arrow. Sew tube-shaped fabrics such as trousers or sleeves, by pulling them over the machine free arm as shown in the diragram.

XX Sewing . Zigzag sewing < There are various zigzag applications, such as applique and overcasting. CRRRLALRLALLLLLLA Turn the handwheel towards yourself to raise the needle. Turn the pattern selection dial to choose the pattern. Zigzag sewing foot (Originally attached to the sewing machine) L _ J m : à Position the fabric and lower the presser foot. Step on the foot controller to begin sewing. L J 29m

XX Sewing ° Adjusting thread tension ‘ RRRALLALRLLRLLLLLLLLLÈLSA . ee @Upper thread is tight

Lower the upper thread tension. @Upper thread is loose Upper thread is tight Wrong Increase the upper side thread tension. Upper thread is loose Note: If the tension does not change even when you adjust the upper thread tension, thread the upper thread and lower thread again.

• Buttonhole sewing COCO TTTTCOTTTTTIT Buttonhole sewing to match the size of the button is possible. For stretch fabric or thin fabric, it is recommended to use a stabilizer for a better buttonhole finish. Change to the buttonhole foot. (Refer to “Changing the presser foot”, p19.) = 1 2 3 4 Buttonhole foot [ fl [] Û = 7 L J Set the buttonhole size and mark Center line lines on the fabric. oo 3mm

Le] 5 Start line a 4 of sewing Button thickness (Button diameter+button thickness+3mm) L J 3 Align the buttonhole foot division line _. … closest to you with the guide line, and Division line lower the presser foot to the start line of Start line sewing on the fabric. . of sewing —ù D Guide line L Center line )

DL Un —— CS TO Raise the needle to the highest position, a set the pattern dial to “1”, sew the left fl side and stop at the line marked on the fabric. A —Ù _ i h 0 il L J . u Le à Raise the needle to the highest position, set the pattern dial to “2”, and sew 5 to <> HN 6 bar-tack stitches. “2” and “4” on the pattern selection dial use the same dial — _ position. (1 L J . . . à T6] Raise the needle to the highest position, HÏTR set the pattern dial to “3”, sew the right side and stop at the line marked on the fabric. \ ; — ' ll

L J . . mn à Raise the needle to the highest position, a set the pattern dial to “4”, and sew 5 to 6

8 | Use the buttonhole cutter to cut the center, making sure not to cut the stitches. er — | Note: If a marking pin is put in the bar-tack area it helps to prevent cutting the bar-tack with the buttonhole cutter. { NS J + Adjustment of buttonhole balance + UT. Use the buttonhole adjustment screw to adjust the balance between the stitches (rear side). + Adjust by turning with the © screw driver of your own. + Don't turn the screw more than 90°. . Note: The original position of buttonhole à “. JButtonhole adjustment screw may vary adjustment according to the model of machine. Screw If the stitches are loose on the right side of the buttonhole, turn slightly in the “- direction.

If the stitches are loose on the left side of the buttonhole, turn slightly in the “+ direction. O

X Sewing ? Thisis a sewing method that prevents unraveling at the ° Overcasting © edge of the fabric. VTT TTTTIT Select one pattern from No.5, No.6 and No.10. Note: Select pattern No.10 when sewing thin fabric. Zigzag sewing foot (Originally \ 6 attached to the \ | | : 5 « {J $ sewing machine) L J

Position the fabric so that the | . right needle entry point at the Right needle entry point edge of the fabric is slightly on the outside. L ” CET

XX Sewing ° Zipper insertion’ VITCOCTTIITTTTIV First sew the left side of the zipper. Set the right side pin of the zipper | Left side pin Right side pin foot to the presser foot holder. N

Align the zipper and the fabric, and tack. Position the fabric so that the zipper is on the 7 right side of the presser foot. & Zipper L J

Sew until just before the presser foot makes contact with the slider, and then stop the sewing machine. Turn the handwheel towards yourself to lower the needle into the fabric. Raise the presser foot. Move the slider to the rear of the presser foot, and finish the sewing. Slider sé: -eSewingihemightsiderontheZippen- cé; a à Release the presser foot and set to the left side pin. Sew the right side of the zipper using the same procedures as for the left side. Note: Sewing in the same direction as the left side will help prevent sewing misaligment.

XX Sewing e. Blind hem stitching 4 In this sewing method the stitch cannot be seen on the front of the fabric. COCO TTIT Zigzag sewing foot (Originally | attached to the sewing machine)

Fold back the cloth so that the folded Tacking area protrudes by about 5 to 7 mm. . Iron and tack by hand. 5 to 7 mm m à Position the cloth so that the left side stitch catches 1 or 2 threads Inside fold of the inside fold. Lower the presser foot and start sewing. Sew evenly so that small Wrong stitches are evenly located on side the right side. Right After sewing, pull out the tacking, side open out the fabric.

Balanced stitches Wrong side Right side Small stitches evenly located on right side. Needle catches too much on the fold Wrong Right side side Needle does not catch on the fold Wrong Right side side Large stitches on right side. The blind hem stitches do not come through

• Feed dog and hook maintenance’ COCO TTTTCTOTTTTTTTTTTTTTTT If the sewing machine makes a loud noise or rotates slowly, or there could be thread waste or dust in the hook or feed dog. Perform maintenance on the hook and the feed dog. A\Caution | Attention AE - ©, Remove presser foot and needle. Loosen screws of needle plate with screw driver for the needle plate and take off needle plate. L J u | | | . à Lift bobbin case in the direction of the arrow and remove it. Brush off lint and dust on feed dog and \ hook, then clean it with a soft cloth. A vacuum cleaner wand or hose may be used to remove lint from this area. L J 39m

DL Un —— CS TO + Atachingthe BobbinCase + Install the bobbin case from the front. The red mark @ on the bobbin case should be in the position, as shown in the diagram. Align the red mark @ and ®), and attach the needle plate with the projection © on the bobbin case positioned as shown in the diagram. Make sure that bobbin case moves slightly from side to side as indicated by the arrow.

Tighten needle plate clamp screws. Turn the handwheel and see if hook moves smoothly. When the bobbin case is attached incorrectly, the handwheel is heavy and does not turn smoothly. At that time remove the needle plate and the bobbin case, attach them again. Attach the needle and presser foot. Make sure that the needle goes into the hole of needle plate correctly while turning the handwheel towards yourself.

RE | —— H — eee % Maintenance + Changing light bulb£ VTC TOTITTOITITTITT Loosen the screw with a “+” Screw screw driver of your own, and take off the face cover in the direction of the arrow. Face cover Turn the light bulb counterclockwise as the arrow in the diagram and remove. Turn the new light bulb clockwise to install. Note: Use a light bulb with a maximum power of 15 W. Always reinstall the face cover after replacing the light bulb. 4Aimmmm

X Maintenance > \Whatis the problem? Check the following 0 Troubleshooting > possibilities before contacting the service 911119114996, center torrepair. Trouble Cause Countermeasure Page The power plug is not inserted | Connect the power plug correctly 10 Does not : : rotate Thread is tangled in the hook, Does not work | ©fthere is a broken needle in Clean the hook 37 the hook Loud noise There is thread waste or dust Slow rotation in the hook or feed dog Remove thread waste or dust 37 The needle is incorrectly installed Install the needle correcily 21 ne needle clamp screw is Firmly tighten the screw 21 loose The needle is too fine for the Use a needle appropriate to the 22 cloth fabric Broken needle The tensi th e tension of the upper : ; thread is too tight Adjust the thread tension 28 MOE EEE IEEtES Do not pull the fabric strongly 23 strongly The bobbin case is not in the Put the bobbin case in the correct 38 correct position position The upper and lower thread are not correctiy threaded Thread the upper and lower thread | 14,15 The thread is tangled in the Remove thread waste from the 37 bobbin case or hook feed dog and hook Broken upper To one Ta thread e tension of the upper : ; thread is too tight Adjust the thread tension 28 The needle is bent The point of the needle is Use a good needle 21 burred Broken lower The lower thread is incorrectly Medio lorer rec 14 thread threaded There is thread waste in the Remove thread waste from the 37 Fabric not fed feed dog feed dog and hook through il al i gl The pattern selection dial is Set a correct pattern 18 set to “2” or “4”

DL Un —— CS TO Trouble Cause Countermeasure Page The needle is incorrectly Install the needle correcily 21 installed Missed The needle is bent Use a straight needle 21 isse stitches The needle and thread are not | Sew with a needle and thread 22 appropriate for the fabric appropriate to the fabric The upper thread is not correctly thread Thread the upper thread correctly 15 Inread À oo AGE upper Adijust the thread tension 28 The fabric The upper and lower thread Thread the upper and lower thread à f 14,15 wrinkles / are not correcily thread again puckers The needle is too thick for the Use a needle appropriate to the 22 cloth fabric The needle is burred Use a good needle 21 The lower thread is incorrectl : Too much threaded Ÿ | Thread the lower thread again 14 lower thread The tension of the upper showing on thread is too tight Adjust the thread tension 28 right side of the fabric The bobbin is not correctly Insert the bobbin in the bobbin : s s 14 inserted in the bobbin case case correctly The upper thread is not correctly threaded Thread the upper thread correctly 15 Too much The tension of the upper upper thread : pp Adjust the thread tension 28 à thread is too loose showing on wrong side of The upper thread is not the fabric correcily threaded (not threaded through the thread Thread the upper thread correctly 15 guide) If the above treatments do not solve the problem, contact the service center as described in your warranty. When calling for service, please note the MODEL and SERIES that are inscribed on the back of your sewing machine.

220-240V L 50Hz Total 85W [5] max 15W porter Porateur Designed and engineered by

RE | —— H — eee > Maintenance / Others + Servicing double-insulated products < , ,(230V-240V + SOV-2AOV) oo oovoooooovet In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means are provided on a double-insulated product nor should a means for grounding be added to the product. Servicing a double-insulated product requires extreme care and should only be done by qualified service personnel with knowledge of the system under his or her responsibility. Replacement parts for a double- insulated product must be identical to those parts in the product. The symbol is marked on the double-insulated product. J% Others + Safety precaution about the battery CPC TTCTCCOCTTTTTTCOTCTTTTTTOTTTT A\Caution |

We are committed to the protection of the environment. We strive to minimize the environmental impact of our products by continuously improving product design and our manufacturing methods. At end of life please dispose of this product in an environmentally responsible way. The crossed-out wheelie bin symbol featured above and on the product's data-plate means that this product falls under the scope of the E.U. “Waste Electrical and Electronic Equipment” (WÉEE) directive and “Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment” (ROHS) directive and should not be disposed of with your household waste. At end of life, you must ensure that this product is disposed of in accordance with national and local legislation and that it is sorted as Category 2 “Small Domestic Appliances” WEEE. You may be liable under local and national laws for improper disposal of this product. Please consult the web, or a competent national or local body, for the return and collections systems available to you and the locations of your nearest recycling points. If you purchase a new product direct from us we will take your old product back, irrespective of the brand, if it is a like for like sale. As an individual you can make a positive impact on reuse, recycling and other forms of recovery of WEEE. This will reduce use of landfill and minimize the environmental impact of the products you use. Hazardous substances in electronic and electrical products can have a harmful impact on human health and on the environment. 45 mm

% Others + Specificationsi PCT Hook type Horizontal Needle Home-use sewing machine needle (HA-1) Bobbin TOYOTA-exclusive plastic bobbin Maximum stitch length 4 mm Maximum stitch width 5 mm Standard needle position Center standard, left standard Sewing machine weight (main unit) 6.3 kg Sewing machine size Width: 412 mm Depth: 192 mm Height: 292 mm Rated voltage 220 - 240V Rated frequency 50 Hz Rated power consumption 85W Light bulb 15W Battery Alkaline 1.5 V, Mignon/AA/LR6 If you have any queries about this TOYOTA sewing machine, check the warranty for details.