SSME 1000 A1 - Food processor SILVERCREST - Free user manual and instructions

Product type	Countertop blender / Food processor
Brand	SilverCrest
Model	SSME 1000 A1
Dimensions (L x W x H)	approx. 192 x 192 x 465 mm
Weight	approx. 3,800 g (3.8 kg)
Power supply	220-240 V~, 50/60 Hz
Power	1000 W
Bowl capacity	1.8 L (max)
Maximum speed	2400 rpm
Speed setting	Continuous (MIN to MAX) + presets
Preset functions	Smoothie, Crushed ice, Pulse (P)
Bowl material	Glass
Continuous operation duration	2 minutes maximum
Automatic shut-off	Yes (after 1 min 40 s in crushed ice mode)
Safety	Safety switch, safety lock, overheat protection
Bowl cleaning	Dishwasher safe
Motor base cleaning	Dry or damp cloth, do not immerse
Cord length	100 cm
Cord storage	Yes, under the motor base
Warranty	3 years
Product code (IAN)	292859
Intended use	Domestic, indoor – blend, puree, mix, crush ice
Package contents	Motor base, bowl with blade, lid, measuring cap, manual

Frequently Asked Questions - SSME 1000 A1 SILVERCREST

How to use the SilverCrest SSME 1000 A1 blender?

Place the bowl on the motor base, lock it by turning clockwise. Add ingredients, close the lid and measuring cap. Plug in the appliance, turn the rotary switch to ON then select a speed or a preset program (Smoothie, Crushed ice, Pulse). To stop, turn the switch back to OFF and unplug.

How to clean the blender after use?

Unplug the appliance. The bowl, lid and measuring cap are dishwasher safe. For a quick clean, pour 750 ml warm water with a few drops of dish soap into the bowl, close, and press the Pulse button several times. Then rinse with clear water. The motor base is cleaned with a damp cloth, do not immerse.

Can I blend hot or boiling foods?

No, never put hot or boiling foods in the bowl. The glass could crack and the motor could overheat. Let food cool to room temperature before blending.

What to do if the blades do not turn or turn slowly?

Check that the bowl is correctly locked on the motor base and that the lid is closed with the safety lock engaged. If the blades are stuck, turn off and unplug, then remove hard pieces or add a little liquid to facilitate blending.

What is the maximum capacity of the bowl?

The graduated bowl can hold up to 1.8 litres. Do not exceed this level to avoid overflow and ensure good mixing.

How long can I use the blender continuously?

The maximum continuous operation time is 2 minutes (temporary service duration). After this time, turn off the appliance and let the motor cool to room temperature before using again.

Can I wash the blender bowl in the dishwasher?

Yes, the glass bowl, lid and measuring cap are dishwasher safe. Place them in the top basket preferably. The motor base and cord must never be immersed.

How to crush ice with the blender?

Put a maximum of 200 g of ice cubes in the bowl. Turn the switch to ON then press the Crushed ice button. The blender operates intermittently for a maximum of 1 minute 40 seconds. You can stop earlier by pressing the button again. Once the ice is crushed, turn the switch to OFF.

What is the Smoothie button for?

The Smoothie button activates a constant speed optimized for preparing smoothies, blending and chopping food. Press it after turning the switch to ON. The blender automatically turns off after 1 minute or you can stop it manually by pressing the button again.

How to properly install the bowl on the motor base?

Make sure the rotary switch is at OFF and the appliance is unplugged. Place the bowl on the motor base with the handle facing the right, then turn the bowl clockwise until it clicks into place. The safety lock must activate the safety switch on the handle.

USER MANUAL SSME 1000 A1 SILVERCREST

Black-and-white photo of a modern blender with pineapple, grapes, and fruit in foreground (no text or symbols on main objects)

Power-Mixer SSME 1000 A1
Power Blender SSME 1000 A1
Power-Mixer SSME 1000 A1

TARGA GMBH

Coederweg 45

DE-SVAVA CERMANI

Deutsch....2

English 27

Français....49

Nederlands 77

Čeština 101

Español....123

Português....149

Inhalt

Warnung!

Diagram of a mechanical component with two labeled parts (1 and 2), showing rotational motion around a central hexagonal hole (no text or symbols beyond labels)

1. Intended use.... 28
2. Package contents 29
3. Controls 29
4. Technical specifications 29
5. Safety instructions .... 30
6. Before you start.... 35
7. Getting started 36
   7.1 Setting up the blender....36
8. Usage 36
   8.1 Filling the blender jug....36
   8.2 Attaching the blender jug to the motor unit 37
   8.3 Control panel....37
   8.4 Switching on / selecting speed 38
   8.5 Filling the blender jug while the blender is running....39
   8.6 Removing the blender jug from the motor unit 39
   8.7 General tips on using the blender....39
   8.7.1 Chopping and blending food 40
   8.7.2 Preparing smoothies and milkshakes....40
   8.7.3 Crushing ice cubes....40
   8.7.4 Hard ingredients 40
9. Sample recipes 41
   9.1 Mojo Picón....41
   9.2 Guacamole 41
   9.3 Piña Colada....42
   9.4 Frozen Cappuccino....42
   9.5 Smoothie 42
   9.6 Bulgarian Tarator 43
   9.7 Tropical Shake....43
   9.8 Hawaii Mix....43

9.9 Banana Shake 44
9.10 Cosmopolitan....44

10. After use.... 44

10.1 Maintenance/cleaning....44
10.1.1 Cleaning the motor unit....45
10.1.2 Cleaning the lid and the measuring cup....45
10.1.3 Cleaning the blender jug manually 45
10.2 Storage when not in use....45

11. Troubleshooting 46

12. Environmental regulations and disposal information.... 46

13. Conformity 47

14. Warranty information 47

Congratulations!

By purchasing the SilverCrest SSME 1000 A1 table-top blender, hereinafter referred to as the blender, you have opted for a quality product.

Before first using it, familiarise yourself with the way the blender works and read these operating instructions through carefully. Be careful to follow the safety instructions and only use the blender as described in the operating instructions and for the applications given.

Keep these operating instructions in a safe place. If you pass the blender on to someone else, make sure to give them all the relevant documents with it.

1. Intended use

This blender is suitable exclusively for use indoors, in dry, sealed spaces.

Always make sure the blender is on a stable surface.

The blender is exclusively designed for mixing, pureeing and stirring food and crushing ice cubes in private households.

This blender is not intended for commercial use.

The blender may not be used to grind or chop nuts, seeds or stalks or to process hot or boiling foods. It must also not be used to reduce the grain of sugar or salt. Non-food substances should also not be processed.

The blender fulfils all relevant norms and standards associated with CE Conformity. Any modifications to the device other than recommended changes by the manufacturer may result in these standards no longer being met.

2. Package contents

• Motor unit with power cable and plug
- Blender jug with cutting blade
- Measuring cap
- Lid
- This user manual

3. Controls

These operating instructions have a fold-out cover. On the inside of the cover, the blender is shown with figures indicated. The meanings of the numbers are as follows:

1	Measuring cap 9	Rotary switch
2	Lid	10 Smoothie	button
3	Safety catch 11	Crushed ice button
4	Blender jug with scale	12 Pulse button P
5	Handle	13 Non-slip	feet
6	Cutting blades	14 Cord wrap (on the underside of the motor unit)
7	Safety switch	15 Power cable
8	Motor	unit

4. Technical specifications

Manufacturer:	SilverCrest
Model name:	SSME 1000 A1
Operating voltage: 220 - 240 V	~ (AC), 50/60 Hz
Power consumption:	1000 W
Speed:	stepless adjustment, max. 2400 rpm
Power cable length:	100 cm
Dimensions:	approx. 192 x 192 x 465 mm (W x D x H)
Weight:	approx. 3,800 g

Short-time duty (KB time)*: 2 minutes

Protection Class II

* The short-time duty (KB time) is the maximum permitted continuous operating time without the electric motor overheating and potentially being damaged. After this operating period, you must switch off the blender and wait for the motor to cool down to ambient temperature.

5. Safety instructions

Before you use this device for the first time, please read the following notes in this manual and heed all warnings, even if you are familiar with handling electronic devices. Keep these operating instructions in a safe place for future reference. If you sell the device or give it away, pass on the operating instructions at the same time. They form part of the product.

Explanation of symbols

In this user manual, warnings are used as follows. Some symbols are affixed to the product itself in order to alert the user to potential risks.

WARNING!

This symbol denotes important information for the safe operation of the product and user safety. It warns against risks which could, if left unheeded, cause danger to life and limb, injuries or material damage.

Risk of electric shock!

This symbol warns of risks which could, if left unheeded, cause damage to life and limb through electric shock.

This symbol designates products whose physical and chemical composition has been tested and found to be non-hazardous to health when used in contact with food in accordance with the requirements of Ordinance EU 1935/2004.

This symbol denotes further information on the topic.

Children and persons with disabilities

This device is not to be used by children. The device and its power cable (15) should be kept out of the reach of children. Devices may be used by persons with reduced physical, sensory or mental capabilities and/or who have no experience in, or knowledge of, using such devices providing they are supervised or have been instructed in how to use the device safely and have understood the associated risks. Children must not play with the device.

Risk of suffocation!

Packaging material is not a toy. Do not allow children to play with plastic bags. There is a risk of suffocation.

Risk of falling objects!

Make sure that children cannot pull the device from the work surface by the power cable (15). There is a danger of injury.

Keep the device out of the reach of children.

General safety instructions

Risk of electric shock!

- The power cable (15) must not be damaged. Never replace a damaged power cable (15), instead contact

our hotline (see "Warranty information" on page 47). There is a risk of electric shock in the case of a damaged power cable (15).

• Do not open the blender housing - it contains no serviceable parts. Opening the housing can expose you to the risk of electric shock.

• If you notice any smoke, unusual noises or strange smells, switch off the device immediately and remove the plug from the mains socket. If this occurs, do not continue to use the device and have it checked out by an expert. Never inhale smoke from a possible device fire. If you do inadvertently inhale smoke, seek medical attention. Smoke inhalation can be damaging to your health.

• Make sure that the power cable (15) cannot be damaged by sharp edges or hot spots. After use, always wind the power cable (15) back around the cord wrap (14) underneath the motor unit (8).

• Make sure that the power cable (15) cannot become crushed or squashed.
• The device must always be disconnected from the mains when left unsupervised and before assembly, disassembly or cleaning.

• When disconnecting the mains plug from the mains socket, always pull on the plug and never on the cable itself.

• If you notice visible damage to the blender or the power cable (15), switch off the device, remove the mains plug from the mains socket, and contact customer service (see "Warranty information" on page 47).

• Only connect the blender to a properly installed, easily accessible mains socket whose mains voltage corresponds to that on the rating plate. After connecting the device, the mains socket must still be easily accessible so that you can remove the mains plug quickly in the event of an emergency.

- Never immerse the motor unit (8), the power cable (15) or the mains plug in water or other liquids. If liquid does penetrate the motor unit (8), disconnect the plug from the mains socket immediately and contact the hotline (see "Warranty information" on page 47).

Warning about property damage

• Do not leave the blender unattended while running so you can react quickly in the case of hazards.
• If necessary, place something underneath the device, as work-surfaces are sometimes treated with detergents which could attack or even dissolve the non-slip feet (13).
• The blender may not be used to grind or chop nuts, seeds or stalks or to process hot or boiling foods. It must also not be used to reduce the grain of sugar or salt.

- Remove thick or tough fruit skins (e.g. pineapple, citrus fruits, etc.) before blending.

Risk of overheating and fire

• Only ever operate the blender with the blender jug (4) filled and never empty.
• Do not use the device in direct sunlight or near heating devices (heaters, stoves, ovens, etc.).
• Do not place hot or boiling foods in the blender jug (4). Otherwise the motor unit (8) could overheat or the blender jug (4) could crack. Always leave hot or boiling foods to cool down first before adding them to the blender jug (4) and processing with the blender.
• If the cutting blades (6) do not turn or turn only very slowly after you switch it on, switch off the device immediately and remove the mains plug from the socket. Check whether the food is too tough, whether the cutting blades are stuck against a large piece or the device has been incorrectly assembled.

Risk of injury

• Check that the blender is in perfect working order before each use. If there is any visible damage, do not use the blender. This applies in particular to the power cable (15), the motor unit (8) and the blender jug (4).
• Never open the lid (2) while the blender is running. Otherwise, rotating bits of food may be ejected with great

force.

• Never reach into the blender jug (4) while the blender is running because the cutting blade is extremely sharp and rotates quickly.
• Never insert cutlery or other stirring implements into the blender jug (4) while the blender is running as the cutting blades rotate very quickly and may cause considerable damage and injury.
• Children shall be supervised to ensure that they do not play with the blender.
• Be careful when handling the blender, emptying the blender jug (4) and cleaning the device. The cutting blades are extremely sharp.
• Always switch the blender off before removing the blender jug (4) from the motor unit (8).
• Always switch the blender off and disconnect the mains plug from the mains socket before changing accessories or touching parts which move when in use.
• Always switch the blender off and wait for the motor to stop before removing the blender jug (4) from the motor unit (8).

6. Before you start

Unpack the device. First check whether all the parts are complete and undamaged (see "Package contents" on page 29). If any items are missing or damaged, please phone our hotline (see "Warranty

information" on page 47). Keep the packaging material away from children and dispose of appropriately.

The blender jug (4) should be cleaned before first use. For more on this, please refer to the "Maintenance/cleaning" section on page 44.

7. Getting started

7.1 Setting up the blender

Warning!

• Only use the device in dry, enclosed spaces. Never use it outdoors.
- Place the blender on an even and stable surface only. If the blender is not placed on an even surface, it could tip over, possibly causing damage to property and injury.
- Make sure the power cable (15) is not in your working area. Otherwise, you could accidentally pull on it and tip it over or make the blender fall off the work surface.

1. Fully unwind the power cable (15) and feed it through the cable clip on the bottom of the motor unit (8).

2. Place the motor unit (8) on an even, non-slip and dry surface. Do not connect the power cable (15) plug to the mains socket yet!

8. Usage

8.1 Filling the blender jug

1. Remove the lid (2) and measuring cap (1) from the blender jug (4). To do this, hold the handle (5) in one hand and hold on tightly to the blender jug (4). Put the index finger of your other hand through the eyelet on the catch on the back of the lid (2) and lift the lid (2) up off the blender jug (4).
2. Add the desired ingredients to the blender jug (4).
3. Place the lid (2) and measuring cap (1) back on the blender jug (4). To do this, first push the lid (2) down with your thumb on the side of the safety catch (3) on the blender jug (4). Then push the lid (2) down on the front (where the spout is) until it catches. Make sure that the safety catch (3) actuates the safety switch on the top of the handle (5).

8.2 Attaching the blender jug to the motor unit

Warning!

If the rotary switch (9) is set at one of the various power levels between MINM and MAX, the blender will power on as soon as you place the blender jug (4) on the motor unit (8) and close the lid (2).

1. If the mains plug is connected to the mains socket, remove it from the mains socket.

2. Check that the blender's rotary switch (9) is in the OFF position.

3. Place the blender jug (4) on the motor unit (8) and lock it into position. To do this, first twist the blender jug (4) such that the handle (5) of the blender jug (4) is on the right hand side. Now lower the blender jug (4) onto the motor unit (8) and twist it clockwise until it slots into place. This activates the safety switch (7) so that you can then switch on the table-top blender.

4. Connect the power cable (15) plug to a live mains socket.

Warning!

Make sure the power cable (15) is not in your working area. Otherwise you could pull it inadvertently and knock the blender over.

8.3 Control panel

Use the control panel to switch the table-top blender on or off and select a speed.

Rotary switch (9)

You can adjust the speed of the cutting blades (6) steplessly. The speed range is marked from MIN to MAX as a guide.

In the OFF position, the table-top blender is switched off.

In the ON position, the table-top blender is switched on but the cutting

	blades (6) are not moving yet. The blue LEDs in the rotary switch itself light up. First, you need to use the rotary switch to set a speed between MIN and MAX or press the smoothie button (10), the crushed ice button (11) or the pulse button (12) to start the cutting blades (6) moving.
Smoothie button(10)	Press this button to activate the blender function. The cutting blades (6) then rotate at a constant speed optimised for preparing smoothies. This function is suitable for blending and chopping and for smoothies.When this function is activated, there is a blue light on the button.
Crushed ice button(11)	Press this button to activate the crushed ice function. The cutting blades (6) then rotate at high-speed in intervals. This function is suitable for crushing ice cubes.When this function is activated, there is a blue light on the button. The blender works in intervals to crush the ice. After 1 minute and 40 seconds, the blender switches off automatically. If you think that the ice is already properly crushed before this time has elapsed, you can cancel the ice-crushing function at any time (press the crushed ice button again).
Pulse button P (12)	Press this button to activate the pulse function. The cutting blades (6) then rotate at a higher speed for as long as you hold the pulse button pressed down. This function is suitable for chopping foods and cleaning the blender jug (4) and the cutting blades (6).When this function is activated, there is a blue light on the button.

8.4 Switching on / selecting speed

The blender can only be switched on once the blender jug (4) is properly locked into position, correctly seated on the motor unit (8) and the lid (2) is closed.

1. Place the rotary switch (9) in the ON position. The blue LEDs in the rotary switch (9) itself light up.
2. Use the rotary switch (9) to select a speed between the MIN and MAX positions or press the smoothie button (10), the crushed ice button (11) or the pulse button (12) to use one of the pre-set speeds.

Warning about property damage

Please note the short operating time of a maximum of 2 minutes. After this operating period, you must switch off the blender and wait for the motor to cool down to ambient temperature.

8.5 Filling the blender jug while the blender is running

Warning!

• When the blender is running, only ever open the measuring cap (1) and not the entire blender jug (4) lid (2). Otherwise rotating food could be catapulted out.
• When the measuring cap (1) is open, never insert cutlery or other items into the blender jug (4). There is a danger of injury!

Proceed as follows to add ingredients while the blender is running:

1. Rotate the measuring cap (1) clockwise and remove it.
2. Add the desired ingredients to the blender jug (4).
3. Close the measuring cap (1). To do so, insert it into the lid (2) and tighten in an anti-clockwise direction.

Diagram of a mechanical component with two labeled parts (1 and 2), showing rotational motion around a central hexagonal hole (no text or symbols)

8.6 Removing the blender jug from the motor unit

1. Place the rotary switch (9) in the OFF position. If you are finished blending, disconnect the mains plug from the mains socket.
2. Once the motor has stopped rotating, twist the blender jug (4) a little anticlockwise (the handle (5) must point right).
3. Lift the blender jug (4) vertically off the motor unit (8).

8.7 General tips on using the blender

Warning about property damage!

Remove thick or tough fruit skins (e.g. pineapple, citrus fruits, etc.) before blending.

• Wash or clean the ingredients.
  • If you wish to process solid ingredients, cut them into small pieces first (approx. 2 to 3 cm).
• To puree solid ingredients, gradually add small amounts into the blender jug (4) with the measuring cap (1) open. If necessary, add a little liquid.
• If you wish to mix liquid ingredients, start with just a little liquid. Then gradually add small amounts of liquid into the blender jug (4) with the measuring cap open (1).
  • If you are using fresh herbs, remove the stalks.

8.7.1 Chopping and blending food

1. Add the ingredients to the blender jug (4).
2. Use the rotary switch (9) to select the speed you want. If necessary, start with a low speed and increase as required to obtain the consistency you want.
3. To stop blending, move the rotary switch (9) to the OFF position.

8.7.2 Preparing smoothies and milkshakes

1. Add the ingredients to the blender jug (4).
2. Switch the table-top blender on. To do this, switch the rotary switch (9) to the ON position.
3. Press the smoothie button (10). The motor starts rotating.
4. To finish the blending process, press the smoothie button (10) again. Otherwise after 1 minute the blender switches off automatically. When you have finished, move the rotary switch (9) to the OFF position.

8.7.3 Crushing ice cubes

To crush ice, you should fill the blender jug (4) with a maximum of 200 g of ice cubes. Otherwise the ice will not be perfectly crushed.

1. Add the ice cubes to the blender jug (4).
2. Switch the table-top blender on. To do this, switch the rotary switch (9) to the ON position.
3. Press the crushed ice button (11). The motor starts rotating. The blender works in intervals to crush the ice.
4. To finish the process, press the crushed ice button (11) again. Otherwise after 1 minute and 40 seconds the blender switches off automatically. When you have finished, move the rotary switch (9) to the OFF position.

8.7.4 Hard ingredients

1. Add the ingredients to the blender jug (4).
2. Switch the table-top blender on. To do this, switch the rotary switch (9) to the ON position.
3. Hold the pulse button (12) down. The motor starts rotating.

Where possible, work with a series of short bursts. This is better for chopping hard ingredients.

1. To finish the process, release the pulse button (12). When you have finished, move the rotary switch (9) to the OFF position.

9. Sample recipes

This section contains some versatile recipes that can be altered to suit individual tastes by replacing certain ingredients.

9.1 Mojo Picón

This spicy paprika sauce is a recipe from the Canary Islands and is served with potatoes boiled in their skins with lots of coarse salt (Papas arrugadas) there. Also delicious with grilled meats or fish.

• 4 red peppers
• 50ml white wine vinegar
• 1 - 2 chillies
• Cumin
• 1 clove of garlic
  • Paprika (sweet or hot to suit personal taste)
• 200ml olive oil
• Salt

Chop the peppers into small pieces. Halve the chillies lengthways, remove and discard the seeds. Chop finely. Place in the blender jug (4) together with the oil and vinegar. Peel the head of garlic, press and add to the jug.

Purée for approx. one minute at a medium speed.

Season with salt, paprika and cumin and stir through again briefly before serving.

9.2 Guacamole

This extremely healthy avocado cream is popular throughout the South America region. Whether served with Mexican nachos or Argentinian steak, this green cream is a highlight for many dishes.

• 2 ripe avocados
• 1 / 2 lime or lemon
• 2 tomatoes
• Salt and pepper

• 2 - 4 cloves of garlic to suit personal taste

Halve the avocados and remove the stone. Remove the flesh of the fruit from the skin with a tablespoon and chop coarsely.

Place the avocados in the blender jug (4). Press the garlic and add to the jug as well. Squeeze the lime or lemon and pour in the juice. Purée for approx. one minute at a medium speed. Season with salt and pepper, add more lime juice and garlic to taste and stir through briefly. Transfer the avocado cream to a bowl. Chop the tomatoes into small pieces and stir through the avocado cream by hand. Do not leave to stand too long or the cream will go brown. Sprinkle with lemon or lime juice if necessary.

9.3 Piña Colada

The classic Caribbean cocktail made with pineapple and coconut.

For 1 cocktail:

- 100g ice cubes

- 4cl cream

- 5cl white rum

- 4cl coconut cream

- 2cl dark rum

- 10cl pineapple juice

Place the ice cubes in the blender jug (4) and crush for short bursts using the pulse button (12).

Place the crushed ice in a cocktail glass.

Place all other ingredients in the blender jug (4) and blend at a low speed, then beat on at a medium speed until frothy. Pour into the cocktail glass over the ice. Decorate with a pineapple wedge and cocktail cherry on the rim of the glass and serve with a straw.

9.4 Frozen Cappuccino

- 100g ice cubes

• 1 scoop of vanilla ice cream

• 1 cup of strong cold coffee

Place the ice cubes in the blender jug (4) and crush for short bursts using the pulse button (12).

Add vanilla ice cream and stir through at a medium speed. Add the cold coffee and blend briefly at a slow speed.

Serve immediately.

9.5 Smoothie

Serves 4

- 350g berries (e.g. strawberries, raspberries, blueberries or blackberries)

- 500ml orange juice

- 1 tbsp honey

- 1 banana

Wash and clean the berries, halving the strawberries. Slice the banana and place all ingredients in the blender jug (4). Blend for around 30 seconds for a medium to high speed. Serve immediately.

Tip: Particularly delicious in summer with frozen berries. Then, first crush the berries using short bursts with the pulse button (12) and then add the remaining ingredients and blend briefly at a medium speed.

9.6 Bulgarian Tarator

Refreshingly light dish, especially tasty on hot summer days. Serve with fresh bread or jacket potatoes.

• 500g natural yoghurt
• 50g walnuts
• 400g cucumber
• 50 ml olive oil
  • 4 cloves of garlic
• 400ml cold water
• 1 bunch of dill
• Salt and pepper

Roughly chop the walnut halves on a chopping board with a knife. Slice the cucumbers and place in the blender jug (4) with the yoghurt. Press and add the garlic. Cut the dill over the blender jug (4) with scissors. Purée everything briefly at a medium speed. Add the chopped nuts, water and olive oil and mix again (slow or medium speed). Season with salt and pepper.

Garnish with a little dill and a walnut half.

9.7 Tropical Shake

A refreshing cocktail for summer.

• 125 g ice cubes
• 125 ml pineapple juice
• 50 ml orange juice
• 12 small can of peaches with juice
• 60 ml papaya juice

Place the ice cubes in the blender jug (4) and crush for short bursts using the pulse button (12). Add the remaining ingredients to the blender jug (4) and blend at a medium speed.

9.8 Hawaii Mix

A lively cocktail for parties.

• 14 I pineapple juice
• 2 tbsp honey
  • 14 | rum
• 4 bananas
• 1/2 | milk

Peel the bananas, place in the blender jug (4) and purée at a low speed. Add the remaining ingredients to the blender jug (4) and blend at a low speed.

9.9 Banana Shake

The classic among shakes.

• 12 | milk

- A little lemon juice

- 2 bananas

- Approx. 1-2 tbsp sugar or vanilla sugar (depending on taste and how ripe the bananas are)

Peel the bananas, place in the blender jug (4) and purée at a low speed. Add the milk, lemon juice and sugar little by little and blend until everything is evenly mixed.

Serve cold.

9.10 Cosmopolitan

Not just for the jazz club.

- 12ml Cointreau

- 6 ice cubes

- 25ml red berry juice

- 40ml vodka

- Juice of 12 lime

Place the ice cubes in the blender jug (4) and crush for short bursts using the pulse button (12). Add the remaining ingredients to the blender jug (4) and blend at a medium speed.

10. After use

After use clean the blender as described in the "Maintenance / cleaning" section below. Wrap the power cable (15) around the cord wrap (14) and store the blender in a safe and dust-free place.

10.1 Maintenance/cleaning

The blender jug (4), the lid (2) and the measuring cap (1) are dishwasher-safe.

Risk of injury

Never reach into the blender jug (4) because the cutting blades are extremely sharp.

It is recommended that you clean the blender before first use and immediately after each use so that no remnants of food can set in the blender jug (4).

The quickest and easiest way to clean the blender jug (4) inside is to rinse it briefly under the tap and then proceed as follows:

1. Fill the blender jug (4) with approx. 750ml water.

2. Add a few drops of washing-up liquid, close the lid (2) and place the blender jug (4) on the motor unit (8).

3. Connect the mains plug on the power cable (15) to a mains socket, move the rotary switch (9) to ON and press the pulse button (12) a few times.
4. Rinse the blender jug (4) out with plain water.

This will generally be sufficient to clean the cutting blades and the interior of the blender jug (4). If you find it is not sufficient, proceed as described in the "Cleaning the blender jug manually" section below.

10.1.1 Cleaning the motor unit

Risk of electric shock!

• Always remove the plug from the mains socket before cleaning the motor unit (8). Failure to do so could cause an electric shock.
• Do not pour or spray any liquids onto the motor unit (8) and do not immerse it in water or other liquids. This could cause short circuits which could cause electric shocks or burns.

Warning about property damage

- Do not use abrasive or astringent detergents or tools which could scratch the motor unit (8) surface. This could cause damage to the motor unit (8) housing.

Clean the motor unit (8), plastic parts and the power cable (15) with a dry or damp cloth.

Dry the motor unit (8) well.

10.1.2 Cleaning the lid and the measuring cup

The lid (2) and measuring cup (1) can be rinsed as normal. Dry them thoroughly.

10.1.3 Cleaning the blender jug manually

Risk of injury

Never reach into the blender jug (4) because the cutting blades are extremely sharp.

You can rinse the blender jug (4) as normal. To remove stubborn dirt inside the blender jug (4) you can use a long-handled dishwashing brush or bottle brush.

Then rinse it with clean water and dry it thoroughly.

10.2 Storage when not in use

If you no longer need the blender, clean it as described in the "Maintenance / cleaning" section. Then proceed as follows:

1. Wind the power cable (15) around the cord wrap (14) underneath.
2. Store the blender in a safe, dry place away from dust.

11. Troubleshooting

If your blender does not work as normal, follow the instructions below to try to solve the problem. If working through the tips below does not fix the fault, please contact our hotline (see "Warranty information" on page 47).

Risk of electric shock!

Never try to repair the device yourself.

Problem	Possible cause	Remed
Blender does not work.	Mains plug not connected. Connect the mains plug to a live mains socket.
	Blender jug (4) incorrectly seated on the motor unit (8).	Place the blender jug (4) onto the motor unit (8) correctly. See "Attaching the blender jug to the motor unit" on page 37.
	Lid (2) is incorrectly fitted on the blender jug (4).	Place the lid (2) onto the blender jug (4) correctly. See "Filling the blender jug" on page 36.
The cutting blades (6) are turning slowly or not at all.	Cutting blades (6) are blocked or the food is too tough.	Remove any solid objects from the blender jug (4).If necessary, add a little liquid to the blender jug (4).

12. Environmental regulations and disposal information

A symbol depicting a crossed-out rubbish bin on a product means it is subject to European Directive 2012/19/EU. All electrical and electronic devices must be disposed of separately from household waste at official disposal centres.

Do not dispose of the device in household waste or bulky waste collections. Information on collection points and pick-up times can be obtained from your local council or waste disposal company.

Dispose of all packaging in an environmentally friendly manner. Cardboard packaging can be taken to paper recycling centres or public collection points for recycling. Any film or plastic contained in the packaging should be taken to your public collection points for disposal.

13. Conformity

This device complies with the basic and other relevant requirements of the EMC Directive 2014/30/EU, the Low-voltage Directive 2014/35/EU, the ErP Directive 2009/125/EC and the RoHS Directive 2011/65/EU.

The complete EU Declaration of Conformity is available for download from this link: www.targa.de/downloads/conformity/292859.pdf.

14. Warranty information

Dear Customer,

This device is sold with three years warranty from the date of purchase. In the event of product defects, you have legal rights towards the seller. These statutory rights are not restricted by our warranty as described below.

Warranty conditions

The warranty period commences upon the date of purchase. Please keep the original receipt in a safe place as it is required as proof of purchase. If any material or manufacturing faults occur within three years of purchase of this product, we will repair or replace the product free of charge as we deem appropriate.

Warranty period and legal warranty rights

The warranty period is not extended in the event of a warranty claim. This also applies to replaced and repaired parts. Any damage or defects discovered upon purchase must be reported immediately when the product has been unpacked. Any repairs required after the warranty period will be subject to charge.

Scope of warranty

The device was carefully manufactured in compliance with stringent quality guidelines and subjected to thorough testing before it left the works. The warranty applies to material and manufacturing faults. This warranty does not cover product components which are subject to normal wear and which can therefore be regarded as wearing parts, or damage to fragile components such as switches, rechargeable batteries or components made of glass. This warranty is void if the product is damaged, incorrectly used or serviced. To ensure correct use of the product, always comply fully with all instructions contained in the user manual. The warnings and recommendations in the user manual regarding correct and incorrect use and handling of the product must always be observed and complied with. The product is solely designed for private use and is not suitable for commercial applications. The warranty is rendered void in the event of incorrect handling and misuse, if it is subjected to force, and also if any person other than our authorised service technicians interfere with the device. No new warranty period commences if the product is repaired or replaced.

Submitting warranty claims

To ensure speedy handling of your complaint, please note the following:

Before using your product for the first time, please read the enclosed documentation carefully. Should any problems arise which cannot be solved in this way, please call our hotline.
- Always have your receipt, the product article number as well as the serial number (if available) to hand as proof of purchase.
- If it is not possible to solve the problem on the phone, our hotline support staff will initiate further servicing procedures depending on the fault.

Service

Phone: 020 - 70 49 04 03

E-Mail: [e-mail]

Phone: [phone]

E-Mail: [e-mail]

Phone: [phone]

E-Mail: [e-mail]

Phone: 02 - 20 09 025

E-Mail: [e-mail]

IAN: 292859

Manufacturer

Please note that the following address is not a service address. First contact the service point stated above.

TARGA

GmbH

Coesterweg 45

DE-59494 Soest

GERMANY

Table des matières

Commande rotative (9)

Bouton impulsion P (12)

Diagram of a mechanical component with two labeled parts (1 and 2), showing rotational motion around a central hexagonal hole (no text or symbols beyond labels)

Cher client, chère cliente,

Cher client, chère cliente,

Waarschuwing!

Diagram of a mechanical component with two labeled parts (1 and 2), showing rotational motion around a central hexagonal hole (no text or symbols present)

Varování!

Diagram of a mechanical component with two labeled parts (1 and 2), showing rotational motion around a central hexagonal hole (no text or symbols)

¡Advertencia!

Diagram of a mechanical component with two labeled parts (1 and 2), showing rotational motion around a central hexagonal hole (no text or symbols present)

Diagram of a mechanical component with two labeled parts (1 and 2), showing rotational motion around a central hexagonal feature (no text or symbols beyond labels)