90-83000 - Camcorder National Geographic - Free user manual and instructions

Product Type	Action Camera (Camcorder)
Brand	National Geographic
Model	90-83000
Dimensions	59.3 × 41.1 × 24.6 mm
Weight	60 g
Battery Capacity	900 mAh
Recording Time	Approx. 70 minutes (1080p)
Charging Time	Approx. 3 hours
Waterproof Depth	Up to 30 m (with case)
Lens Angle	140° wide angle
Display	1.5 inch TFT
Max Video Resolution	1920×1080 (Full HD)
Max Photo Resolution	12 MP (4032×3024)
Storage	Micro SD card up to 32 GB (not included)
Video Format	AVI (MJPEG compression)
Interface	Micro USB 2.0, Micro HDMI
Accessories Included	Waterproof case, bicycle mount, base mounts, multifunction mounts, belt clip, tripod adapter, USB cable, AC adapter, straps, cleaning cloth, etc.
Safety Warnings	Choking hazard from small parts; battery acid risk; electric shock; do not disassemble; avoid high temperatures.
Cleaning Instructions	Use soft lint-free cloth for lenses; dry cloth for exterior; rinse waterproof case with clean water.
Warranty	2 years (extendable to 5 years upon registration at www.bresser.de/warranty within 3 months of purchase)

Frequently Asked Questions - 90-83000 National Geographic

How do I open the waterproof case?

Press and hold the ▼ switch (1) then slide the ◀ arrow (2) to open the clamp (3). To close, press the case door down (1), snap the clamp to the hinge (2), then press the clamp down (3).

How do I replace the battery?

Open the battery cover by pressing on it. Insert the battery correctly. To remove, simply open the cover and take out the battery. Charge via USB with the included adapter or computer.

How do I record video?

Turn on the camera by holding the power switch for 3-5 seconds. It defaults to video mode. Insert a Micro SD card and press OK to start/stop recording. The icon indicates video mode.

What memory card does it support?

It supports Micro SD cards up to 32 GB. For best performance, use a branded card and format it on your computer before use.

Is the camera waterproof without the case?

No, the camera itself is not waterproof. It must be used inside the included waterproof case to achieve a depth rating of up to 30 meters.

Can I charge the camera while recording?

Yes, the camera supports video recording while charging. You can charge via USB power adapter or computer even when the camera is off.

How do I mount the camera on a helmet?

Use the flat or curved base with double-sided sticker (12) for vertical mount. For side mount, combine multifunction mounts (6a, 6b) and base (9/5) with sticker.

How do I reset the camera to factory settings?

In settings menu, select System Reset and confirm. This restores default settings and erases all user data.

What should I do if the camera doesn't turn on?

Ensure the battery is charged and properly inserted. Press and hold the power switch for 3-5 seconds. If still off, try connecting to USB power. If problem persists, contact customer service.

How can I view videos on a TV?

Connect the camera to a TV using a Micro HDMI cable (not included). In playback mode, videos will be displayed on the TV screen.

USER MANUAL 90-83000 National Geographic

NATIONAL GEOGRAPHIC™

BRESSER

Action Camera

12 MP

1080p Full HD

Black and white photo of a national geographic video camera with visible lens and mounting base (no text or symbols on body)

EN Operating instructions

8 1/4" Stativadapter (male/female)

Close-up of a small electronic device with a black cover and circular button, no visible text or symbols

Black industrial pipe clamp with three vertical posts and a central valve (no text or symbols visible)

Four black mechanical components arranged in a row, with one component above it (no visible text or symbols)

Two mechanical components, one resembling a tool or bracket and the other a device with a handle (no visible text or symbols)

Three identical mechanical components labeled (a), (b), and (c) with no visible text or symbols on the parts themselves.

DE

Two black plastic electronic components with no visible text or symbols

Two black plastic components, one with a spiral tip and the other a flanged cap (no text or symbols visible)

Two black rectangular electronic components with circular holes, no visible text or symbols

Two transparent plastic containers with black bolt holes, labeled 10 and 11 above (no text or symbols on the containers themselves)

Abstract curved lines with three dots at endpoints, no text or symbols present

Two rectangular electronic cards with visible traces and labels, no readable text or symbols on the cards themselves.

Three black plastic components arranged horizontally on a white background (no text or symbols visible)

Black-and-white photo of a connected USB cable and a black plug (no text or symbols visible)

Simple 3D-rendered object with a curved line extending from it, no text or symbols present

Akku austauschen

Two electronic devices with a close-up of one showing a magnified view of its internal components (no visible text or symbols)

DE

Two electronic devices: a USB cable and a black plug, both with no visible text or symbols.

Close-up of a camera module being held, showing front and side views with no visible text or symbols

Funktionen

Three identical black-and-white images of a camera module with a circular lens, shown from different angles (no text or symbols)

Product photo of four electronic components: a connector, a compact case, a flat capacitor, and a battery (no visible text or symbols)

Close-up of a mechanical component with a curved black base and metallic housing (no visible text or symbols)

DE

Three black plastic electrical connectors with metallic leads, one small gray component nearby (no text or symbols visible)

Two electronic components with metallic pins, one showing a circular top and the other a rectangular pin (no visible text or symbols)

Three electronic components: a black hard drive, a black compact case, and a white rectangular box (no visible text or symbols)

Black and white photo of a HiFi geografiR camera with attached mechanical arm (no visible text or symbols)

Fahrradhalterung:

Gürtelhalterung:

DE

Black and white photo of a national geographic video camera with visible lens and mounting base (no text or symbols on body)

EN

Operating instructions

About this Instruction Manual

Please read the safety instructions and the operating instructions carefully before use. Keep these instructions for renewed use at a later date. When the device is sold or given to someone else, the instruction manual must be provided to the new owner/user of the product.

EN

Intended Use

This product is intended only for private use. It was developed as an electronic medium for the use of multimedia services.

General Warnings

• Risk of choking — Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as these materials pose a choking hazard. This product contains small parts that could be swallowed by children.
• Leaking battery acid can lead to chemical burns. Avoid contact of battery acid with skin, eyes and mucous membranes. In the event of contact, rinse the affected region immediately with a plenty of water and seek medical attention.
• Risk of electric shock — Never bend, pinch or pull the power and connecting cables, extensions and adapters. Protect the cables from sharp edges and heat. Before operating, check the device, cables and connections for damage. Never use a damaged unit or a unit with damaged power cables. Damaged parts must be exchanged immediately by an authorised service centre.
• Risk of property damage! — Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.
• Do not expose the device to high temperatures. Use only the supplied power adapter. Do not short-circuit the device or throw them into a fire. Excessive heat or improper handling could trigger a short-circuit, a fire or an explosion.

- Do not interrupt an on-going data connection to a computer before all data has been transferred. This could lead to data loss for which the manufacturer is not liable.

Notes on cleaning

• Turn off the camera
• Clean the eyepieces and/or lenses only with a soft, lint-free cloth, (e.g. microfibre cloth). To avoid scratching the lenses, use only gentle pressure with the cleaning cloth.
• Only use a dry cloth to clean the exterior of the device. To avoid damaging the electronics, do not use any cleaning fluid.
• Clean the protective case after each use with clear, clean water and dry it thoroughly.

EC Declaration of Conformity

Bresser GmbH has issued a Declaration of Conformity' in accordance with applicable guidelines and corresponding standards. This can be viewed any time upon request.

Disposal

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.

EN

Do not dispose of electronic devices in the household garbage! As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner. Empty, old batteries must be disposed of at battery collection points by the consumer. You can find out more information about the disposal of devices or batteries produced after 6 January 2006 from your local waste-disposal service or environmental authority.

The integrated battery must only be removed for disposal. Opening the device housing can damage the unit.

Drain the battery completely before disposal. Remove all the screws in the housing and open the device housing. Remove the connections to the battery and remove it. Cover the open contacts with tape and package the battery in such a way that it cannot shift in the packaging.

Scope of delivery

① Camera
② Waterproof case
③ Bicycle mount
4 Thumb knobs and cap nut
5 Base mounts
⑥ Multifunction mounts 2x 90° (a+b) and 1x straight (c)

⑦ Camera housing and belt clip

⑧ 1/4" Tripod adapter (male/female)

9 Base for flat and curved surface

10 Case doors

⑪ Cable ties

12 Double sided sticker for base mounts

13 Straps

14 USB cable and AC adapter

15 Metal safety wire and cleaning cloth

Black industrial pipe clamp with three vertical posts and a central valve (no text or symbols visible)

Two mechanical components, one resembling a gear or clamp and the other a bracket (no visible text or symbols)

Close-up of a small electronic device with a black cover and circular button, no visible text or symbols

Four black mechanical components arranged in a row, with one component above it (no visible text or symbols)

Three identical mechanical components labeled (a), (b), and (c) with no visible text or symbols on the parts themselves.

EN

Two black plastic electronic components with no visible text or symbols

Two black, textured objects resembling mechanical or electronic components, one with a white mark and the other with a spiral pattern (no text or symbols)

Two black rectangular electronic components with circular holes, labeled with number 9 in top-left corner (no other text or symbols)

Two transparent plastic containers with black bolt holes, labeled 10 and 11 above (no text or symbols on the containers themselves)

Abstract curved line pattern with four dots at endpoints (no text or symbols)

Two credit cards with visible branding and printed markings (no readable text or symbols)

Three black plastic components arranged horizontally on a white background (no text or symbols visible)

Black-and-white photo of a connected USB cable and a black plug (no text or symbols visible)

Simple 3D-rendered object with a curved line extending from it, no text or symbols present

How to open and close the waterproof case

How to open:

Press and hold down the

▼ switch (1) and then use the ◀ arrow (2) to open the clamp (3).

How to close:

Press the case door all the way down (1) and then snap the clamp to the hinge (2).

Now, simply press the clamp down (3) to close.

How to replace the battery

Charge with the included power adapter or via a computer using the usb cable.

How to swap the case door

Align the case door with the hinge and press down until it clicks into place.

Close-up of a black electronic device with a close-up view showing a button labeled '17.4' and an arrow pointing to it (no readable text or symbols beyond the label)

Two electronic devices: a USB cable and a black plug, both with no visible text or symbols.

Close-up of a camera module being held, showing front and side views with no visible text or symbols

EN

Functions

Battery cover
Switch to open the Waterproof case

EN

Mount your camera

Flat surface or curved surface mount:

Choose the flat or curved base depending on the surface.

Three identical black-and-white images of a camera module with a circular lens, shown from different angles (no text or symbols)

Mount on flat base:

graph TD
    A["Device Setup"] --> B["Internal Display"]
    B --> C["Assembly Module"]
    C --> D["Final Display"]
    style A fill:#f9f,stroke:#333
    style B fill:#ccf,stroke:#333
    style C fill:#cfc,stroke:#333
    style D fill:#fcc,stroke:#333

EN

Mount - Examples:

Base-Mount:

Snap the base mount (5) into the base (9). Use the flat or curved base, depending on the surface. Now use the thumb knobs (4) to mount the waterproof case (2).

Bicycle mount:

Attach the waterproof case with camera (1/2) on the multifunction mount (6a). Now secure the bicycle mount (3) to multifunction mount (6a) and then attach to the handlebars. Tighten the thumb knobs (4) firmly.

Belt mount:

Place the camera (1) in the housing and then snap the clip for the belt holder to the housing. Fix the clip to the belt.

EN

Helmet-Mount (Vertical mount):

Apply the double sided sticker (12) at the base (9) and attach the base mounted camera to the helmet.

Helmet-Mount (Side mount):

Attach the multifunction mount (6a) on the multifunction mount (6b) and then mount the base (9/5) to multifunction mount (6a). Finally mount the waterproof case with camera to (6b). Apply the double sided sticker (12) at the base (9) and attach to the helmet.

Product features

• A water-resistant casing that allows you to film fascinating water sports: Water-resistant up to 30 metres underwater.
• High definition screen that displays and replays fascinating videos that have been recorded.
• Rechargeable battery that is easy to replace and prolongs your camera's service life.
  • Video recording while charging.
  • Video recording with battery.
  • 12 mega pixel (HD) wide-angle lens.
• HDMI HD output.
  • Supports Micro SD/TF Memory cards up to 32 GB maximum.

Operating

1. Inserting Micro SD card\*

Note: For best performance, please choose a branded Micro SD card and format it on your computer before use. Unbranded cards are not guaranteed to work flawlessly.

2. Installing or removing the battery

A. Press on the battery cover to open it.
B. Correctly install the battery into the camera.
C. Remove Battery: Simply open battery cover to take the battery out.

3. Charging

A. Charging can be done with the power adapter or by connecting the action camera to a computer via the usb cable.
B. The action camera can record video while charging
C. Charging of the action camera can be done even when it's powered off.

*SD card not included

4. Turning camera on and off

A. Press and hold the power switch for three to five seconds to turn the camera on or off.

B. Switch the display screen on or off by pressing the [DOWN] button to save battery life during use.

5. Mode Switching

A. Press the [Power On-Off / mode] button [💡] repeatedly to cycle through the camera modes.

Camera mode
Description

	Video recording mode Video, Loop Recording, Motion detect
	shooting mode Single, Photo timer, Burst, Time lapse
	Play back mode Play back content on the TFT display or on a TV via HDMI cable.
	Settings Adjust all camera settings

6. How to record videos and configure recording setting

6.1. Video Recording

Turn the camera on. You will start with the video recording mode. There will be an

icon in the upper left corner. Insert a SD card and start recording by pressing

"OK". Press "OK" again if you want to stop the recording.

6.2. Photo shooting & Settings

Switch to photo shooting mode by pressing [💡]. There will be an icon in the upper left corner. Press "OK" to take photos.

6.3. File Storage & Play back

After you have finished recording use a USB cable to export the videos onto a computer for play back. You can also take the Micro SD card out and access the image data with a card reader.

Settings

Video Resolution Change	video resolution(1920X1080 recommended)
Picture Resolution Change	Picture resolution(12M - 4032X3024 recommended)
Photo Timer Off / 2s / 5s / 10s
Burst Off / 3 Picture / 5 Picture
Time-lapse Single / 3s / 5s / 10s
Time Stamp Off / On
Motion Detect Off / On (video mode only)
Loop Recording Off / 1 Min. / 2 Min. / 3 Min. (video mode only)

EN

Audio Record Off / On
EV (Exposure value) +2/3 / +1/3 / +0.0 / -1/3- 2/3 / -1.0 / -4/3 / -5/3 / -2.0
Delete Delete One / Delete All
Protect Lock One / Unlock OneLock All / Unlock All
Format All data on the sd card will be deleted
Language Choose OSD language
Volume Change OSD volume
Auto Off Off / 1 Min. / 3 Min. / 5 Min.
LCD Off (Auto screen off) Off / 3 Min. / 5 Min. / 10 Min.
System Reset Reset system to default settings
Refresh rate 50 Hz / 60 Hz
Date/Time Set current date and time
Panel Rotate Off / On
Version View current fi rmware version

Technical Data

TFT Display 1.5 inch (3.81 cm) display
Lens 140° wide angle
Waterproof case Resistant up to 30 metres
Language options English / German / French / Spanish / Italian / Portuguese / Chinese Traditional / Chinese Simplifi ed / Japanese / Russian
Resolution of photos 12 MP (4032x3024), 10 MP (3648x2736), 8 MP (3264x2448), 5 MP (2592x1944), 3 MP (2048x1536), 2 MP (1920x1080), 1.3 MP (1280x960), VGA (640x480),
Resolution of videos 1920x1080,	1440x1080, 1280x720, 848x480, 640x480
Video format AVI
Compressed format of videos mjpeg

EN

Storage Micro SD card up to 32 GB (not included)

Shooting mode Single shot / Self-timer (2s/5s/10s)

Frequency of optical source 50Hz/60Hz

USB interface USB 2.0

Power source interface 5 V === 500 mA

Battery capacity 900 mAh

Power dissipation 400mA@4.2V

Recording time About 70 minutes (at 1080p)

Charging time About 3 hours

Operating systems (OS) Window XP / Vista / Win 7 / Mac OS X

Dimensions 59.3x41.1x24.6 mm

Weight 60 g

Note: Specifications could be subject to change due to upgrading or updating. Please regard the actual product as the standard.

Warranty and warranty term extension

The warranty term is two years from the date of purchase. Please keep your proof of purchase. Register at www.bresser.de/warranty and fill out a brief questionnaire to get your warranty term extended to five years. Registration must be completed within three months of purchase (date of receipt) to validate the warranty. If you register thereafter, the warranty term will not be extended.

If you have problems with your device, please contact our customer service fi rst. Do not send any products without consulting us fi rst by telephone. Many problems with your device can be solved over the phone. If the problem cannot be resolved by phone, we will take care of transporting your device to be repaired. If the problem occurred after the warranty ended or it is not covered by our warranty terms, you will receive an estimate of repair costs, free of charge.

Service Hotline: [phone]

Important for any returns:

Please make sure to return the device carefully packed in the original packaging in order to prevent damage during transport. Also, please enclose your receipt for the device (or a copy) and a description of the defect. This warranty does not imply any restriction of your statutory rights.

EN

Your dealer: Art. No.:

Description of problem: ....

Name: Telephone:

Street: Date of purchase:

City/Postcode:...... Signature:......

Black and white photo of a national geographic video camera with visible lens and mounting base (no text or symbols on body)

ES

Close-up of a small electronic device with a black cover and circular button, no visible text or symbols

Black industrial pipe clamp with three vertical posts and a central valve (no text or symbols visible)

Four black mechanical components arranged in a row, with one component above it (no visible text or symbols)

Two mechanical components, one resembling a tool or bracket and the other a device with a handle (no visible text or symbols)

Three identical mechanical components labeled (a), (b), and (c) with no visible text or symbols on the parts themselves.

Two black plastic electronic components with no visible text or symbols

Two black plastic components, one with a spiral tip and the other a flanged circular base (no text or symbols)

Two black rectangular electronic components with circular holes, labeled with number 9 in top-left corner (no other text or symbols)

Two transparent plastic enclosures labeled 10 and 11, each with a black bolt on the surface (no text or symbols on the enclosure itself)

Abstract curved line pattern with four dots at endpoints (no text or symbols)

Two credit cards with visible branding and printed markings (no readable text or symbols)

Three black plastic components labeled 13 and 14, arranged horizontally (no text or symbols on the objects themselves)

Black and white photo of a connected USB cable and a black plastic plug (no text or symbols visible)

Simple 3D-rendered object with a curved line extending from it, no text or symbols present

Black rectangular electronic device with a small screen and directional arrow indicator (no text or symbols)

Tapa de la batería

Two electronic devices with a close-up of one showing a mechanical component and the other with a magnified inset (no visible text or symbols)

ES

Two electronic devices: a USB cable and a black plug, both with no visible text or symbols.

Close-up of a camera module being held, showing front and side views with no visible text or symbols

Funciones

Three identical black-and-white images of a camera module with a circular lens, shown from different angles (no text or symbols)

Montaje vertical:

Four electronic components: a connector, a switch, a compact case, and a memory card (no visible text or symbols)

Close-up of a mechanical component with a curved black base and two circular features (no visible text or symbols)

ES

Montaje lateral:

Three black plastic electrical connectors with metallic leads, one small gray component nearby (no text or symbols visible)

Two electronic components with pins, one showing a dome-like top and the other a metallic connector (no visible text or symbols)

Three electronic components: a black USB drive, a black rectangular case with a screw, and a white CD card (no visible text or symbols)

Exterior view of a NATO GEOGRAPHIC camera module (no visible text or symbols on body)

National Geographic supports vital work in conservation, research, exploration, and education.

Visit our website: www.nationalgeographic.com

© 2016 National Geographic Partners LLC.

All rights reserved. NATIONAL GEOGRAPHIC and

Yellow Border Design are trademarks of the

National Geographic Society, used under license.

BRESSER

Bresser GmbH

Gutenbergstr. 2

DE-46414 Rhede