CHO-60CHA210A GX - Range hood Vivax - Free user manual and instructions

Product Type	Range Hood (Cooker Hood)
Model	CHO-60CHA210A GX
Brand	Vivax
Width	60 cm
Installation Height	65–75 cm above cooking surface
Power Supply	220–240 V ~ 50 Hz
Number of Fan Speeds	3 (Low, Medium, High)
Controls	Mechanical push buttons or touch control (depending on version)
Lighting	LED (Round 1.5W/2W or Rectangle 2W)
Grease Filter	Aluminum, washable (monthly cleaning)
Activated Carbon Filter	Optional for recirculation mode; replace annually
Exhaust Diameter	150 mm
Modes	Ducted (external vent) or Recirculation (with carbon filter)
Timer	Yes (5-minute quick timer on touch control)
Automatic Shut-Off	Yes (after timer countdown)
Noise Level	Low noise operation
Material	Stainless steel (presumed)
Weight (approx.)	15 kg
Dimensions (H x W x D)	Adjustable chimney height; base 60 cm × ~50 cm
Safety Features	Overheat protection (presumed), child safety lock (not specified)
Warranty	3 years (as per warranty section for range hoods)

Frequently Asked Questions - CHO-60CHA210A GX Vivax

What is the recommended installation height for the Vivax CHO-60CHA210A GX range hood?

The range hood should be installed 65–75 cm above the cooking surface for optimal performance.

Can I use this range hood in recirculation mode?

Yes, you can use it in recirculation mode. You need to install an activated carbon filter (sold separately) to trap odors.

How do I clean the grease filter?

Remove the aluminum grease filter and clean it monthly with warm soapy water or a household detergent. Allow it to dry completely before reinstalling.

How often should I replace the activated carbon filter?

The carbon filter should be replaced at least once a year, or more frequently if the hood is used intensively.

What should I do if the fan does not work but the light is on?

Check if the fan blade is jammed. If not, the motor may be damaged. Switch off the unit and contact a qualified service technician.

How do I replace the LED light?

First, remove the aluminum grease filter. Then unplug the LED lamp cable and take out the whole LED light. Replace it with a new LED of the same type and rating (round 1.5W/2W or rectangle 2W).

What is the diameter of the exhaust pipe?

The exhaust pipe should have an interior diameter of 150 mm.

Can I use the range hood with a gas stove?

Yes, but ensure the distance between the hood and the gas cooking surface is at least 65 cm. Also, adequate ventilation is required.

Is the touch control version equipped with a timer?

Yes, on the touch control version, press the '+' and '-' buttons together for 1 second to activate a 5-minute countdown timer. The motor and light will turn off automatically.

What should I do if the range hood vibrates excessively?

Check if the fan blade is damaged or if the motor is not fixed tightly. Also ensure the hood is properly hung on the bracket. Contact a qualified technician if needed.

USER MANUAL CHO-60CHA210A GX Vivax

VAŽNE SIGURNOSNE UPUTE

Simbol munje u trokutu upozorava korisnika na prisutnost opasnog napona koji nije izoliran unutar proizvoda i koji može biti dovoljno snažan da predstavlja rizik od strujnog udara.

Uskličnik unutar trokuta upozorava korisnika na važne upute za rad i održavanje u dokumentu priloženom u ambalaži.

OPREZ

RIZIK OD STRUJNOG UDARA NE OTVARAJ

Nemojte otvarati poklopac. Korisniku ni u kojem slučaju ne smije obavljati radove unutar uređaja. Samo kvalificirani tehničar ima pravo obavljati popravke. U slučaju nepridržavanja sigurnosnih uputa, proizvođač neće snositi odgovornost za štetu.

SIGURNOSNE NAPOMENE

Diagram of airflow around a mechanical structure with directional arrows indicating movement (no text or symbols)

b. Prije ugradnje isključite uređaj i izvucite kabel iz utičnice.

Hand inserting a plug into an electrical outlet (no text or symbols visible)

Pure technical line drawing of a 3D geometric structure without any text, numbers, or symbols

- Podignite kuhinjsku napu i objesite napu na nosač.

Diagram of a brick wall with a chimney and a person standing on top, no text or symbols present

- Izbušite rupe od 2×8 mm koji će pridržavati nosač dimnjaka i pritegnite nosač na zid s dva predviđena vijka. Montirajte dimnjak na uređaj i učvrstite ga s 2 vijka za nosač.

Technical line drawing of a brick chimney mounted on a base, showing structural details without any text or symbols.

- Povucite unutarnji dimnjak kako biste postavili visinu dimnjaka. Kada dosegnete željenu visinu, tada pričvrstite 2 vijka od 4x8 mm na učvrsne rupe na zidnom nosaču "II" kao što je prikazano na desnoj slici.

• Izbušite rupe od 2×8 mm za montiranje nosača "II" dimnjaka. Pričvrstite i pritegnite nosač na zid s dva predviđena vijka.
• Montirajte dimnjak na uređaj i učvrstite ga na nosač "II" s dva vijka.

Diagram of a mechanical or fluid system with directional arrows indicating flow or movement (no text or symbols)

Illustration showing two hand-drawn diagrams of a mechanical or architectural component, one with a downward arrow and the other with a curved arrow (no text or symbols)

Technical line drawing of a mechanical fan or motor assembly with no visible text or symbols

UPORABA

Mehanička / Elektronička kontrola

Four circular icons with different symbols: a fan, a propeller, a sun, and a light bulb, arranged horizontally (no text or labels)

Verzija 1

A. Okrugla LED rasveta (1,5W i 2W)

1.A Uklonite Aluminijskie filtre
2.A Odvojite LED lampu kako je prikazano i odspojite konektor napajanja LED lampe.

3 A Priključite novu LED lampu istog tipa i snage i vratite ju natrag u napu.

Mechanical diagram showing two wheels mounted on a frame with directional arrows indicating motion (no text or symbols)

Technical line drawing of a ceiling-mounted appliance with circular components and an upward arrow indicating motion (no text or symbols)

B. 2W Kvadratna LED rasvjeta

1.B Uklonite Aluminijski filtar

2.B Odvojite LED

lampu kako je prikazano i odspojite konektor napajanja LED lampe.

Priključite novu LED lampu istog tipa i snage i vratite ju natrag u napu

RJEŠAVANJE PROBLEMA

Diagram of airflow around a mechanical structure with directional arrows indicating movement (no text or symbols)

Hand inserting a plug into an electrical outlet (no text or symbols visible)

Oprez! Obratite pažnju na upozorenje u uputstvu o radu uređaja kada se vazduh ispušta iz prostorije.

Kada je aspirator instaliran pored kuhinjske ploče koji se snabdeva energijom koja nije električna (plinska ploča) i kada uređaji rade istovremeno, negativni pritisak u sobi ne sme biti veći od 4 Pa ( 4 × 10^5 bara)

- Izbušite rupe od 3 x 8 mm za montažu nosača. Postavite i pritegnite nosač na zid predviđenim tiplama i vijcima.

- Za model s nagnutom prednjom pločom, pre ugradnje trebate da izbušite dodatne rupe od 4 x 8 mm i pričvrstite nosač.

Pure technical line drawing of a 3D geometric structure without any text, numbers, or symbols

- Podignite aspirator i objesite ga na nosač.

Diagram of a brick wall with a chimney and a person standing on top, no text or symbols present

- Izbušite rupe od 2×8 mm koji će da pridržavaju nosač dimnjaka i pritegnite nosač na zid sa dva predviđena vijka. Montirajte dimnjak na uređaj i učvrstite ga sa 2 vijka za nosač.

Technical line drawing of a brick chimney mounted on a wall, showing structural details without any text or symbols.

- Donji dimnjak učvrstite pomoću 2 vijka od 4x8 mm.

- Povucite unutarnji dimnjak kako biste podesili visinu dimnjaka. Kada dosegnete željenu visinu, tada pričvrstite 2 vijka od 4x8 mm na učvrsne rupe na zidnom nosaču "II" kao što je prikazano na desnoj slici.

- Izbušite rupe od 2×8 mm za montažu nosača "II" dimnjaka. Pričvrstite i pritegnite nosač na zid s dva predviđena vijka.

- Montirajte dimnjak na uređaj i učvrstite ga na nosač "II" s dva vijka.

Diagram of a mechanical or fluid system with directional arrows indicating flow or movement (no text or symbols)

Illustration showing two hand-drawn diagrams of a mechanical or architectural component, one with an arrow indicating direction and the other with a curved arrow (no text or symbols)

Technical line drawing of a mechanical fan or motor assembly with no visible text or symbols

KORISNIČKE INSTRUKCIJE

Mehanička / Elektronska tastatura

Four circular icons with different leaf and sun symbols, no text or labels present

Verzija 1

A. Okrugla LED rasveta (1,5W i 2W)

1.A Uklonite Aluminijskie filtere
2.A Odvojite LED svetlo kako je prikazano i odspojite konektor napajanja LED svetla.
3 A Priključite novo LED svetlo istog tipa i snage i vratite svetlo natrag u aspirator.

Mechanical diagram showing two wheels mounted on a frame with directional arrows indicating motion (no text or symbols)

Technical line drawing of a ceiling-mounted fixture with circular components and an upward arrow indicating direction (no text or symbols)

B. 2W Kvadratno LED svetlo

1.B Uklonite Aluminijski filter

2.B Odvojite LED svetlo kako je prikazano i odspojite konektor napajanja LED svetla.

Priključite novo LED svetlo istog tipa i snage i vratite svetlo natrag u aspirator.

REŠAVANJE PROBLEMA

Hand inserting a plug into an electrical outlet (no text or symbols visible)

Pure technical line drawing of a 3D geometric structure without any text, numbers, or symbols

Isometric line drawing of a brick wall with a small object on top, no text or symbols present

Technical line drawing of a chimney structure mounted on a brick wall (no text or symbols)

Two-step diagram showing hand positioning of a rectangular object on a flat surface, with no text or symbols present.

Four circular icons with different symbols: a fan, a three-blade fan, a four-blade fan, and a sun (no text or labels)

Верзија 1

Mechanical diagram showing two wheels mounted on a frame with directional arrows indicating motion (no text or symbols)

Technical line drawing of a ceiling structure with circular components and an upward arrow indicating direction (no text or symbols)

Diagram of airflow around a mechanical structure with directional arrows indicating movement (no text or symbols)

Hand inserting a plug into an electrical outlet (no text or symbols visible)

Pure geometric diagram of a 3D object with dashed lines and control points, no text or symbols present

Architectural diagram of a brick wall with a chimney and support structure (no text or symbols)

Technical line drawing of a chimney mounted on a brick wall, showing structural details without any text or symbols.

Instalimi (Ventilimi i brendshëm)

Diagram of a mechanical or fluid system with directional arrows and a central block, no text or symbols present.

Two-step diagram showing hand positioning of a mechanical component, one with an arrow indicating motion (no text or symbols)

Technical line drawing of a mechanical fan or motor with a close button and rotation arrow (no text or symbols on the diagram itself)

Vërejtje:

Four circular icons with different symbols: a fan, a propeller, a turbine, and a sun (no text or labels)

Versioni 1

0 Butoni i fikjes (Off button)

Mechanical diagram showing two wheels mounted on a rail, with directional arrows indicating motion (no text or symbols)

Technical line drawing of a ceiling-mounted room with circular components and an upward arrow indicating direction (no text or symbols)

Diagram of airflow around a mechanical structure with directional arrows indicating movement (no text or symbols)

Hand inserting a plug into an electrical outlet (no text or symbols visible)

Pure geometric diagram of a 3D object with dashed lines and control points, no text or symbols present

- Kuhinjsko napo obesite na kavelj za stenski nosilec.

Architectural diagram showing a brick wall and a pedestal structure with a person standing on top (no text or symbols)

Technical line drawing of a chimney mounted on a brick wall, showing structural details without any text or symbols.

- Spodnji dimnik pritrdite z 2 kosoma vijakov 4x8 mm.

Diagram of a mechanical or fluid system with directional arrows indicating flow or movement (no text or symbols)

Two-step diagram showing hand positioning of a mechanical component, one with downward arrow and the other with curved arrow (no text or symbols)

V enoto vložite filter z aktivnim ogljem in ga obrnite v smeri urnega kazalca. Enako ponovite tudi na drugi strani.

Opomba:

Technical line drawing of a mechanical fan or motor assembly with no visible text or symbols

DELOVANJE

Mehanski / elektronski gumb

Four circular icons with different leaf-like shapes, arranged horizontally (no text or symbols)

Različica 1

0 Gumb za izklop

Mechanical diagram showing two wheels mounted on a rail, with arrows indicating motion direction (no text or symbols)

Isometric diagram of a ceiling-mounted appliance with circular components and an upward arrow indicating direction (no text or symbols)

Thank you for choosing this cooker hood.

This instruction manual is designed to provide you with all required instructions related to the installation, use and maintenance of the appliance.

In order to operate the unit correctly and safety, please read this instruction manual carefully before installation and usage.

The cooker hood use high quality materials, and is made with a streamlined design. Equipped with large power electricmotor and centrifugal fan, it also provides strong suction power, low noise operation, non-stick grease filter and easy assembly installation

It is important that you read these instructions before using your product and we strongly recommend that you keep them in a safe place for future reference.

WELCOME!

This device meets the highest standards, innovative technology and high comfort use.

Read these instructions carefully before using your new unit, and keep it carefully.

If you follow the instructions, your new appliances will provide you with many years of good service.

READ CAREFULLY THIS MANUAL AND KEEP THEM FOR FUTURE REFERENCE!

IF YOU SELL OR TRANSFER DEVICE TO OTHER PEOPLE, BE SURE TO INCLUDE THESE INSTRUCTIONS!

IMPORTANT SAFETY INSTRUCTIONS WARNING

The flash with the symbol of arrowhead, inside an equilateral triangle alerts the user about the presence of a dangerous tension not isolated inside the product which can be sufficiently powerful to constitute a risk of electrocution.

The point of exclamation inside an equilateral triangle alerts the user about the presence of important operating instructions and maintenance in the document enclosed in the package.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

Do not open the cover. In no case the user is allowed to operate inside the unit. Only a qualified technician from the manufacture is entitled to operate. By ignoring the safety instructions, the manufacturer cannot be hold responsible for the damage.

SAFETY PRECAUTIONS

1. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction.
2. Children being supervised not to play with the appliance.
3. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
4. Children shall not play with the appliance.
5. Cleaning and user maintenance shall not be mad by children without supervision.

6. There shall be adequate ventilation in the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge air back to the room).

7. There is a fire risk if cleaning is not carried out in accordance with the instructions!

8. Do not flame under the range hood
9. CAUTION: Accessible parts may become hot when used with cooking appliances.
10. The Air must not be discharged into a flue that is used for exhausting fumes from appliances brning gas or other fuels.
11. When the range hood is located above gas appliance, this distance shell be at least 65cm
12. Regulations concerning the discharge of air have to be fulfilled.
13. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
14. Never unplug the feed cable from the plug by tugging on the cable. Do not touch the feed cable with wet hands. Never move the appliance by pulling the cord and make sure the cord cannot become entangled.
15. Always disconnect the appliance from the supply before assembling, disassembling or cleaning.
16. The user must not leave the device unattended while it is in work.
17. This appliance is only to be used for household purposes and only for the purpose it is made for.
18. This appliance is intended for indoor use only
19. The appliance is not intended to be operated by means of an external timer or a separate remote-control system. Your device must not be used connected to the same

power cable or fuse with another device.

1. Only use the appropriate power connection and power socket for this device.
2. Failure to maintain the appliance in a clean condition could lead to damage of the surface that could adversely affect the life of the appliance and possibly result in a hazardous situation. Such damages are not included in the warranty.
3. WARNING: Switch off the appliance before changing accessories or approaching parts which move in use.
4. Steam cleaner is not to be used.
5. The use of accessory attachments, not recommended or sold by the appliance manufacturer, may cause hazards.
6. Do not use appliance other than for its intended use.

Electrical connection

Make sure that the voltage (see name plate) and your home power supply match.

The mains plug should only be inserted into a correctly installed 220-240 V \~ 50 Hz socket.

No user-serviceable parts inside. Refer servicing to qualified service personnel.

Only plug this unit into a properly earthed outlet. If in doubt seek advice from a suitably qualified engineer.

Failure to follow these instructions can result in death, fire, or electrical shock.

INSTALLATION

1. Prepare for installation

a. If you have an outlet to the outside, your cooker hood can be connected as below picture by means of an extraction duct (enamel, aluminum, flexible pipe or inflammable material with an interior diameter of 150mm).

b. Before installation, turn the unit off and unplug it from the outlet.

c. The cooker hood should be placed at a distance of 65\~75cm above the cooking plane for best effect.

Diagram of airflow around a mechanical structure with directional arrows indicating movement (no text or symbols)

Hand holding a plug inserted into an electrical socket, with a black arrow indicating the direction of insertion (no text or symbols present)

Attention! Observe the warning in the instruction sheet concerning the operation of the appliance when air is discharged from the room.

When the range hood and appliance supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must be not exceed 4 Pa (4×10-5 Bar)

- Drill 3 x 8mm holes to accommodate the bracket. Screw and tighten the bracket onto the wall with the screws & screw plugs provided.

- For inclined panel Model, need to drill 4 x 8mm extra holes & fixing screws & screw plugs before installation.

Pure geometric diagram of a 3D object with dashed lines and circular markers, no text or symbols present

- Leave up the cooker hood and hang onto the wall bracket hook.

- Fix the one-way-valve to the air outlet of the cooker hood. Then, attached the exhaust pipe onto the one-way-valve as shown below.

2. Chimney installation

2.a Glass model and T shape model

- By Put the upper chimney into lower chimney .Then pulling out the upper chimneyupwards. Adjustto reach the height required.

- Sliding the chimney to adjust the chimney height. When the height you required is reached, then hang the fixing hole to the fixing screws as showed in below pictures.

Isometric line drawing of a brick wall with a small object on top, no text or symbols present

- Drill 2×8mm holes to accommodate the plate II. Screw and tighten the plate II onto the wall with 2 screws provided. Assembly the chimney onto the unit and fix it with 2 screws.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

2.b Tower model

- By Put the inner chimney into upper chimney. Then pulling out the upper chimneyupwards. Adjust to reach the height required.

Technical line drawing of a brick chimney mounted on a wall, showing structural details without any text or symbols.

- Fix the lower chimney with 2 pcs of 4x8mm screws.

- Sliding the chimney to adjust the chimney height. When the height you required is reached, then fix 2 pcs of 4x8mm screws onto the hole fixing with plate I as showed in below pictures

• Drill 2 x 8mm holes to accommodate the plate II. Screw and tighten the plate II onto the wall with 2 screws provided.
• Assembly the chimney onto the unit and fix it with 2 screws.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Installation (Vent inside)

If you do not have an outlet to the outside, exhaust pipe is not required and the installation is similar to the one show in section "Installation (Vent outside)".

Activated carbon filter can be used to trap odors.

In order to install the activated carbon filter, the grease filter should be detached first. Press the lock and pull it downward.

Diagram of a mechanical or fluid system with directional arrows and a central block, no text or symbols present.

Two-step diagram showing hand pressing a component on a flat surface, with no text or symbols present.

Plug the activated carbon filter into the unit and turn it in clockwise direction. Repeat the same on the other side.

Note:

• Carbon filter(s) are not included into Range Hood standard accessories. To purchase Carbon filter, please ask your dealer or service.
• Make sure the filter is securely locked. Otherwise, it would loosen and cause dangerous.
• When activated carbon filter attached, the suction power will be lower.

- The electrical connection must correspond to the electrical requirement noted on the rating plate, which is placed inside the cooker hood.

- The appliance should now be connected to the electrical supply.

- Check that the appliance is operating correctly by selecting each speed and switching the light bulbs on and off.

- Use a stainless steel cleaner and polish on the stainless steel sections of the appliance.

- If you are using the appliance in recirculation mode, then you should now fit the carbon filter.

Technical line drawing of a mechanical fan or motor with a circular arrow indicating 'CLOSE' (no text or symbols on the diagram itself)

OPERATION

Mechanic/Electronic Push button

Four circular icons with different leaf and fan symbols, no text or labels present

Version 1

0 Off button

It's used for turning off the fan.

Low Speed button

It's used for Ventilation on the kitchen. It is suitable for simmering and cooking which do not make much steam.

Medium Speed button

Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button

When high density of smoke or steam produced, press high-speed button for highest effective ventilation.

Light button

NOTE: If Low / Medium/ High speed buttons are press at the same time, the unit will only operate at the highest speed

Touch control – Ver 1

Off button

It's used for turning off the fan.

+ Speed plus button

For increasing the speed of the fan

- Speed decrease button

For decreasing the speed of the fan.

Light button

8 Digital display

Fan speed display:"1" for Low speed, "2" for Medium speed, "3" for High speed.

Quick timer: Press "+" & "-" hold for 1 second, Digital display will flashing & into 5 minutes count down, after 5 minutes motor & light will turn off automatic & Buzzer sound for 1 second.

MAINTENANCE

Before any maintenance or start to cleaning switch the unit off and disconnect unit from mian supply!

Regular Cleaning

Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit.

Grease Filter Monthly Cleaning

WARNING: Clean the filter every month to prevent any risk of fire.

The filter collects grease, smoke and dust.

The filter is directly connected with efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate on the filter. Clean it with household cleaning detergent.

Annual Cleaning for Activated Carbon Filter

Apply to unit that installed internal air circulation (not vented to the outside).

This filter traps odours and must be replaced at least once a year depending on how frequent the cooker hood used.

To prurchase a new Carbon Filter, contact your dealer or Service centre.

Light Bulb replacement

WARNING

If the supply LED bulb is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

1. Switch the unit Off and unplug the appliance from mains supply.

2. Remove the LED lamp according to different type on the hood:

A. Round LED Lamp (1,5W i 2W)

1.A Remove the Aluminium Filter

2.A Unplug the LED lamp cable as shown on drawing

3A Take out the whole LED light from the panel and replace the same type and rated LED light

Mechanical diagram showing two wheels mounted on a frame with directional arrows indicating motion (no text or symbols)

Technical line drawing of a ceiling-mounted fixture with circular components and an upward arrow indicating direction (no text or symbols)

B. 2W rectangle LED

1.B Remove the Aluminium Filter

2.B Unplug the LED lamp cable as below drawing and take out the whole LED light from the panel and replace the same type and rated LED light

TROUBLESHOOTING

The following simple issues can be handled by the user. Please call the after-sale service department if the issues are not settled!

Problem Possible cause Solution
Light on, but fan does not work	The fan blade is jammed	Switch of the unit and repair by The motor is damaged. qualified service personnel only
	The motor is damaged
Both light and fan do not work	The light bulb burned	Replace the bulb with correct rating
	Power cord looses	Plug in to the power supply again.
Serious Vibration of the unit	The fan blade is damaged.	Switch of the unit and repair by qualified service personnel only.
	The fan motor is not fixed tightly.	Switch of the unit and repair by qualified service personnel only
	The unit is not hung properly on the bracket	Take down the unit and check whether the bracket is in proper location.
Suction performance not good	Too long distance between the unit and the cooking plane	Readjust the distance to 65-75cm

TRANSPORT AND SERVICE

WARNING: Handling and transportation. It is required to perform transportation of device in its own original box. Metal, Plastic or Glass parts may be broken during Incorrect packaging. Its electrical parts may be damaged.

Unplug It while It is operating for transport, maintenance or repair purposes.

DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT

To protect our environment and to recycle the raw materials used as completely as possible, the consumer is asked to return unserviceable equipment to the public collection system for electrical and electronic.

The symbol of the crossed indicates that this product must be returned to the collection point for electronic waste to feed it by recycling the best possible raw material recycling.

By ensuring this product you will prevent possible negative effects on the environment and human health, which could otherwise be caused due to improper disposal of that product. The recycling of materials from this product, you will help to preserve a healthy environment and natural resources.

For detailed information about the collection of EE products contact the dealer where you purchased the product.

EU DECLARATON OF CONFORMITY

This device is manufactured in accordance with the applicable European standards and in accordance with all applicable Directives and Regulations.

EU declaration of conformity can be downloaded from the following link: www.msan.hr/dokumentacijaartikala

JAMSTVENI LIST HR

VIVAX

MODEL UREĐAJA

SERIJSKI BROJ

DATUM PRODAJE

BROJ RAČUNA PRODAVATELJA

POTPIS I PEČAT PRODAVATELJA

1. Ovim jamstvom M SAN Grupa kao davatelj jamstva u Republici Hrvatskoj jamči besplatan popravak istog u skladu s važećim propisima i u skladu s uvjetima opisanim u ovom jamstvenom listu. Ovim jamstvom jamčimo da će predmet ovog jamstva raditi bez pogreške uzrokovane eventualnom lošom izradom ili lošim materijalom izrade. Svi, eventualno nastali, kvarovi biti će besplatno otklonjeni u ovlaštenom servisu u jamstvenom roku.

2. UVJETI JAMSTVA Jamstveni rok počinje od dana kupnje proizvoda i traje:

60 MJESECI (5 godina)	HLADNJACI,VERTIKALNE I HORIZONTALNE LEDENICE
36 MJESECI (3 godine)	SAMOSTOJEĆI ŠTEDNJACI, PERILICE I SUŠILICERUBLJA, PERILICE SUĐA, KUHINJSKE NAPEUGRADBENE PEĆNICE I PLOČE, KUHINJSKE NAPEGRIJALICE VODE

1. U slučaju kvara na proizvodu koji je predmet ovog jamstva, obvezujemo se da ćemo isti popraviti u najkraćem mogućem roku, a najkasnije u roku od 45 dana. Ako se proizvod ne može popraviti ili se ne popravi u roku od 45 dana, biti će zamijenjen novim. Jamstvo će biti produženo za vrijeme trajanja popravka.

2. Jamstvo se priznaje samo uz račun o kupnji, te uz ovaj jamstveni list koji mora biti ispravno popunjen odnosno mora sadržavati datum prodaje, pečat i potpis prodavatelja.

5. JAMSTVO NE OBUHVAĆA

POTPIS I PEČAT PRODAVATELJA

GARANCIJSKA IZJAVA

1. Ovom garancijom garantira proizvođač proizvoda, preko KIM TEC d.o.o., kao uvoznika i davatelja garancije u Bosni i Hercegovini besplatan popravak istog u skladu s važećim propisima i u skladu s uvjetima opisanim u ovom garantnom listu. Ovom garancijom garantiramo da će predmet ove garancije raditi bez greške uzrokovane eventualnom lošom izradom i lošim materijalom izrade. Svi eventualno nastali kvarovi biti će besplatno otklonjeni u ovlaštenom servisu u garantnom roku.

2. UVJETI GARANCIJE: Garantni rok počinje teći od dana kupnje proizvoda i traje:

60 MJESECI (5 godina)	HLADNJACI,VERTIKALNE I HORIZONTALNE ŠKRINJE
36 MJESECI (3 godine)	ŠTEDNJACI, PERILICE I SUŠILICE RUBLJA, PERILICESUĐA, KUHINJSKE NAPE, UGRADBENE PEĆNICE IPLOČE, GRIJALICE VODE

1. U slučaju kvara na proizvodu koji je predmet ove garancije, obavezujemo se da ćemo isti popraviti u najkraćem mogućem roku, a najkasnije u roku od 45 dana. Ako se proizvod ne može popraviti ili se ne popravi u roku od 45 dana, biti će zamijenjen novim.
2. Garancija se priznaje samo uz račun o kupnji, te uz ovaj garantni list koji mora biti ispravno popunjen odnosno mora sadržavati datum prodaje, pečat i potpis prodavatelja.
3. Davalac garancije osigurava servis i rezervne dijelove 7 godina od datuma kupnje.

GARANCIJA NE OBUHVAĆA: